ADDITION ALTERATION TO CERTAIN MARRIED ACCOMMODATION AT SHILLONG UNDER GE SHILLONG

Amount

Taking down chowkat or frame exc 1.5 Sqm but n exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames complete all as specified and directed.

Taking down shutters of any description n exc 1.0 Sqm and refixing in same opening complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sqm and n exc 2 sqm and refixing in same opening complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sqm and n exc 2.0 sqm each complete all as specified and directed.

Taking down shutters of any description n exc.1.0 Sqm each complete all as specified and directed.

Demolition of brickwork/solid concrete block or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Dismantling of stone slabs and tiles of any description or thickness in floors aprons laid in any mortar complete all as specified and directed .

Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed

Dismantling boarding any description fixed in any position with nails complete all as specified and directed

Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed

Taking down plastering on lathing (other than wire-netting, without removing lathing, in cement mortar (one side only measured in cases where both sides are plastered).complete all as specified and directed

Dismantling water tanks exc 500 ltrs but not exc 1000 ltrs capacity complete all as specified and directed

Taking up or down steel tubing and disconnection, for 15mm bore of pipes complete all as specified and directed

Taking up or down steel tubing and disconnection, for 20mm bore of pipes complete all as specified and directed

Taking up or down steel tubing and disconnection, for 25mm bore of pipes complete all as specified and directed

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded in concrete, brick work, masonary etc. portion and making good disturbed ground complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling fencing wire mesh any type and any size complete all as specified and directed.

Excavating over area not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and directed

Excavation in trenches not exceeding 1.50 m wide and not exceeding 1.50 m in depth for foundations or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.50 m in depth and getting out in soft/loose soil complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil complete all as specified and as directed..

Excavation in post holes (or similar holes) each not exceeding 0.50 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, in soft/loose soil complete all as specified and as directed.

Removal of excavated material to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

Material and labour for hard core of gauge not exceeding 63 mm of broken stone or boulders , spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Material and labour for plain Cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and directed.

Material and labour for Plain Cement Concrete 1:3:6 type C-2 (using 40 mm gaded stone aggregate) as in surface channel & drain complete all as specified and directed.

M&L for Plain Cement Concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for Precast cement concrete block masonry type C-1, 1:3:6 (using 20 mm graded stone aggregate) with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 including necessary formwork and moulds complete all as specified and directed.

M&L for precast cement concrete type C1 1:3:6 (20mm graded aggregate) block massonry with solid blocks n exc 10 cm in width and settings in CM 1:4 complete all as specified and directed.

Material and labour for reinforced Cement Concrete type nominal mix (1:1.5:3) (using 20 mm graded aggrgate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Material and labour for reinforced Cement Concrete type nominal mix (1:1.5:3) (using 20 mm graded aggrgate) as in columns, pillers, pier post and struts complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles , including necessary form work finishing even and smooth without using extra cement , complete as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Supply only Integral waterproofing compound complete all as specified and directed.

Cutting chases, pinning in concrete block work making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and directed.

Labour only for chamfer, splays or arris in facework of Granite not exc 15mm wide complete all as specified and directed.

M&L for 18/20mm thick granite slab ( as in table top rubbed and polished) as in counter basin, cooking platform fixed in CM 1:4 , pointing in white cement 1:2 using marble dust with admixture of pigment to match complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts,struts,piers, coloumns complete all as specified and directed.

M&L for 2nd class hard wood in scantling clean sawn timber fixed complete all as specified and directed.

S&F including dismantling 20mm thick 2nd class hard wood boarding fixed with nails in eaves board plained one side with butt joint complete all as specified and directed. .

M&L for 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid ,rounded or chamfered ,put together with glue pinned at joints complete all as specified and directed.

S&F 35mm thick 2nd class hard wood skelton shutters open rebated and prepare to receive glass, gauze, etc edges of framing plain, fitted with cut and mitred beads for securing glass, gauze etc, and fitted to chowkhat, sizes of members of shutters complete as specified in SSR Part-I, Section 8, Clause 8.24(a) complete all as specified and directed.

S&F 30 mm thick Flush door shutters solid core construction with block board core and ply wood face pannels commercial veneered on both faces complete all as specified and directed.

S&F solid PVC door frame of size 50 mmx 47 mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with particle board core, 28 to 30 mm thick (stiles) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on front face & 2 mm plain colour PVC sheet on back face as per specification and drawing complete all as specified and directed.

S&F brass 100 mm long barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F powder coated aluminium 200 mm long barrel tower bolts of extruded section complete all as specified and directed.

S&F powder coated aluminium alloy sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet , cast or extruded section and fixing bolts and sliding bolts of extruded section or cast-aluminium with plate type 300mm size with bright bolt not less than 12 mm dia with and including aluminium alloy complete all as specified and directed.

S&F mild steel butt hinges of size 100mm, heavy weight, cold rolled mild steel complete all as specified and directed.

S&F mild steel butt hinges of size 125mm, heavy weight, cold rolled mild steel complete all as specified and directed.

S&F floor door stopper of brass body and tongue with hard drawn steep spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed. .

S&F 300mm long MS Helical door spring Welded to steel /Fixed to wooden door frame including roller and roller plate etc of approved quality complete all as specified and directed. .

S&F extruded fancy type Brass handles fabricated type of size 100 mm complete all as specified and directed.

S&F powder coated extruded aluminium alloy handles, fabricated type of size 150 mm complete all as specified and directed.

S&F in repairs 20 mm dia curtain rod, stainless steel, chromium plated fancy type with fixing including clamp/brackets complete all as specified and directed.

S & F in repairs tubular towel rail 600mm long, D type stainless steel complete all as specified and directed.

S&F Magnet catches for cupboard shutter, brass body and striking plate including letting in, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Mild steel work for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work onforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for MS work for screws bolts 5 to 10mm dia of neck (Machine made) with hexagonal or square heads at one end and screwed both ends, each screwed end to be fitted with wasahers and square nut, exc. 5 cm and n. exc. 10 cm long diameter of shank 11 to 15 mm complete all as specified and directed.

S & Fixing in repair 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

S&F Round bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) complete all as specified and directed.

Material and labour for high strength steel TMT bars (Fe 500D) 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Material and labour for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Gde Fe-290(Gde E-165) complete all as specified and directed.

Material and labour for Structural mild steel, rolled section of grade Fe-290-W(Gde E-165) framed work as in doors or gates of angle or other section with gusset plates, rails, braces, and mounting arrangement etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

M&L for Pressed Steel frame size 105 mm x 60 mm for door with one or more rebate including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and directed.

M&L for Pressed Steel frame size 125 mm x 60 mm for door with one or more rebate including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and directed.

S&F GI wire netting 0.90 mm dia and 12 mm mesh lathing to wood or metal studding, joist, etc. in wall ceiling stanchions, beam etc including all laps cutting and waste complete all as specified and directed.

S&F powder coated (min thickness of powder coating 50 micron) aluminium frame for doors, windows , ventilators plain or sliding type with one or more rebates including joining cleat for fixing etc.complete all as specified and directed.

S&F powder coated (min thickness of powder coating 50 micron) aluminium sliding door shutters , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , handles 2 nos in each door , hinges , anodised aluminium snap beading screws etc complete all as specified and directed.

S&F powder coated (min thickness of powder coating 50 micron) aluminium window and ventilator shutters sliding type without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws ,including locking fittings complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling with aluminium main T-flange of 25 mm and web 30 mm fixed to surrounding wall angle with flange and web 25 mm, cross T- flange and web 25 mm , Main T suspended from soffit @1200 mm C/C using 4mm dia GI wire aluminium frame will be 600x600 to receive ceiling board complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Supply only chain link MS galvanised fencing, any size or type complete all as specified and directed..

S&F 2 mm thick fibre reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof , wall etc. complete all as specified and directed.

M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheet as in ridge of 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 4mm thick non asbestos fibre cement building boards 600mm x 600mm fixed or laid/inserted to timber/GI/Aluminium frame work with screws as in ceiling complete all as specified and directed.

S&F in repairs 18/19 mm thick block boards, grade I quality,exterior grade, commercial type, fixed with screws to timber frame complete all as specified and directed..

S&F 12 mm thick block boards, grade I quality,exterior grade, commercial type, fixed with screws to timber frame complete all as specified and directed.

S&F 12mm thick PVC boards fixed with screws to timber frame complete all as specified and directed.

S&F 0.90 mm thick decorative laminates type 1 of surface finish colour and pattern as approved fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

S&F 0.90mm thick PVC decorative laminates type 1 of surface finish colour and pattern as approved tixed with approved adhesive as per manufacturees instructions complete all as specified and as directed.

M&L for 12 thick seamless calcium silicate ceiling made out of 1800x1200 size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillings head with under head cutter at 200 mm centre to centre incl finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seamless finish fibre tape to provide incl two coat of putty and two coat of OBD design incl GI frame for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.90 mm thick having two equal flanges 15 mm each and web of 45 mm suspended from soffit at approx 900 mm c/c with GI cleat and steel expansion fasternerswith and incl ceiling section (nexc 1.20 m lenght) 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.50 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm c/c with 4 mm suspendor wire complete all as specified and as directed.

M&L for 20-25 mm thick mirror polished Kota stone in single piece in riser/tread of steps over 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 20mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement screed 1:4 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) , as in plinth protection finished even and smooth with out using extra cement complete all as specified and directed.

M&L for 100mm thick cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base complete all as specified and directed.

M & L for 25mm thick PCC 1:2:4 type B1 (using 20mm graded aggregate) as in subfloors finished even and rough without using extra cement complete all as specified and directed.

M & L for Glazed ceramic Coloured Tile 300x600x7 mm thick in skirting, dados, etc., set and jointed in neat cement slurry and pointed in white or colour cement to match the tile laid over and including a backing coat of 10mm thick in CM 1:4 complete all as specified and directed.

M&L for Joint free Non Skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour including Screed bed or bedding layer of mortar 15 mm thick in CM (1:6) complete all as specified and directed.

M&L for Joint free Non Skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour laid over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for outdoor 10mm thick vitrified paving tiles (square /rectangular) polished area of each tiles exc 0.06 sqm but not exc 0.11 in floors laid over and including 15mm thick in CM 1:6 screed bed jointed pointed with coloured cement to match the tiles complete all as specified and directed.

M&L for outdoor 10mm thick vitrified paving tiles (square /rectangular) polished area of each tiles exc 0.06 sqm but not exc 0.11 in skirting laid over and including. 10mm thick in 1:4 screed bed jointed pointed with coloured cement to match the tiles complete all as specified and directed.

M&L for 10 mm thick vitrified ceramic tiles lightshade (square /rectangular) polished area of each tiles n exc 0.36 sqm in floors laid over and including. 15mm thick screed bed in CM 1:6 jointed in neat cement slurry and pointed in coloured cement to match the tiles complete all as specified and directed..

M&L for 10 mm thick vitrified ceramic tiles lightshade (square /rectangular) polished area of each tiles n exc 0.36 sqm in skirting / dado laid over and including. 10 mm thick backing coat in CM 1:4 jointed in neat cement slurry and pointed in coloured cement to match the tiles complete all as specified and directed..

M&L for machine pressed pre polished chequered cement concrete tiles 300mm X 300mm X 25mm thick over and including 15mm thick screed bed in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement to match as in floor complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick or concrete work in CM 1:4 using water proofing compound @ 3% finished even and smooth without using extra cement complete all as specified and directed. Note: WPC will be measured and paid separately under relevant item of BOQ.

M&L for rendering 15 mm thick lathing plaster in CM 1:4 finished even and smooth without using extra cement using water proofing compound @ 3% complete all as specified and directed. Note: WPC will be measured and paid separately under relevant item of BOQ.

M&L for rendering 15mm thick on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick on fair faces of ceiling surface in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing complete all as specified and directed.

M&L for providing 1mm thick wall care putty on wall surfaces complete all as specified and directed.

M&L for preparation of new wall surafces and applying two coats of oil bound distemper over and including 1mm thick wall care putty complete all as specified and directed.

M&L for Complete removal of existing treatment on old wall surfaces and applying two coats of oil bound distemper over and including 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of new wall surfaces and applying two coats of oil bound distemper complete all as specified and directed.

M&L for Complete removal of existing treatment on old wall surfaces and applying two coats of oil bound distemper complete all as specified and directed.

M&L for Complete removal of existing treatment on old ceiling surfaces and applying two coats of oil bound distemper over and including 1mm thick wall care putty complete all as specified and directed.

Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour complete all as specified and directed.

M & L for complete removal of old existing treatmen from ceiling surfaces and applying two coats of white washing complete all as specified and directed.

M&L for waterproof cement based exterior wall putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1 mm over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:- Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI Step 3) Allow 6-8 hrs time to dry the putty surface. Note : (a.) The work pertaining to periodical services & Water Proofing shall be executed from authorized applicator through manufacturer of which the materials .i.e. Paint, Distemper, Putty etc. is proposed to be used by the contractor and approved by Garrison Engineer. (b) Cost of scafolding upto 10m hight of building is included in this item. (c) Masking of window/doors during spray painting using polythine film will be included. (d) Cleaning and clearing site of paint, mats etc. included. (e) 05 years guarantee of painting work will be admissible after date of completion and 15% amount will be reserve against painting work after date of completion for the 05 years.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm Note- (a) Primer and emulsion application to be carried out through air less spray machine ( Only mechanical application allowed except in paint application on bands/chajja/building edges/borders/projections where contrasting color as specified and directed is to be applied) (b) The work pertaining to periodical services & Water Proofing shall be executed from authorized applicator through manufacturer of which the materials .i.e. Paint, Distemper, Putty etc. is proposed to be used by the contractor and approved by Garrison Engineer. (c) Cost of scafolding upto 10m hight of building is included in this item. (d) 05 years guarantee of painting work will be admissible after date of completion and 15% amount will be reserve against painting work after date of completion for the 05 years.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed..

M&L for 4.80 mm thick sheet glass ordinary quality and glazing fixed to aluminium frame exc 0.50 sqm in each pane complete all as specified and directed..

S&F 6.30 mm thick sheet glass of ordinary quality and glazing fixed to aluminium frame square exc 0.50 sqm complete all as specified and directed.

S&F 8.00 mm thick sheet glass of ordinary quality and glazing fixed to aluminium frame square exc 0.50 sqm complete all as specified and directed.

M&L for 4.80 mm thick frosted sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm in each pane complete all as specified and directed.

M&L for solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

M&L for 12 mm thick toughened sheet clear glass incl edges bevelled /rounded including grinding / cutting complete with all fittings/ washers/handlesand bolts complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description over 10cm in width or girth and treated with one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation surface of wood and wood based material new or old of any description and girth and treated with two coats of creosote oil complete all as specified and directed.

M&L for preparation of new steel surfaces of any description , over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat red oxide zinc primer complete all as specified and directed.

Supply and Laying Steel Water Tubing 15mm dia (Bore), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation complete all as specified and directed.

Supply and Laying Steel Water Tubing 20mm dia (Bore), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation complete all as specified and directed..

Supply and Laying Steel Water Tubing 25mm dia (Bore), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation complete all as specified and directed.

Supply and fixing rotational moulded HDPE water storage tank ,triple layer ,ISI marked (cylinderical vertical type with closed top) of capacity 500 ltrs in position incl 20mm bore float valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixing rotational moulded HDPE water storage tank ,triple layer ,ISI marked (cylendrical vertical type with closed top) of capacity 1000 ltrs in position incl 20mm bore float valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs CP Bib taps, cast copper alloy fancy type 15mm bore , screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Pillar tap 15 mm, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down, high pressure with or without letter 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for fixing complete all as specified and directed.

S&F in repair 15 mm CP basin mixer for mixing hot & cold water screwed down for iron pipe line complete all as specified and directed.

S&F in repair 15 mm CP sink mixer for mixing hot & cold water screwed down for iron pipe line complete all as specified and directed.

S&F in repairs stop valve cast copper alloy screwed down, high pressure with crutch or butter fly handle 20mm dia complete all as specified and directed.

S&F in repairs stop valve cast copper alloy screwed down, high pressure with crutch or butter fly handle 25 mm dia complete all as specified and directed.

S&F stop valve cast copper alloy screwed down, high pressure with crutch or butter fly handle 15mm dia complete all as specified and directed.

S&F in repairs Brass CP angular stop cock fancy type 15mm bore with Capstan heads complete all as specified and directed.

S&F PVC Connections 15mm size with PTMT Nuts of length 450mm and fixed complete all as specified and directed.

S&F Stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays ,incl bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Supply & fix in repair 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as specified and directed.

Supply & fix in repair for 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends 110mm dia complete all as specified and directed.

S&F PVC (SWR) bends 75mm dia complete all as specified and directed.

Supply & fix in repair PVC(SWR) bends with access door of any radius 110mm bore complete all as specified and directed.

Supply & fix in repair PVC(SWR) bends with access door of any radius 75mm bore complete all as specified and directed.

Supply & fix in repair PVC(SWR) 110mm dia in junction single, (Single 'T') equal or unequal with access door complete all as specified and directed.

Supply & fix in repair PVC(SWR) 110mm dia in junction single, (Double 'T') equal or unequal with access door complete all as specified and directed.

Supply & fix in repair PVC (SWR) reducers 110mm dia complete all as specified and directed.

Supply & fix in repair PVC(SWR) 75mm dia vent cowls complete all as specified and directed.

S&F in repairs Brass chromium plated bottle traps 32 mm dia for wash basins with inlet and outlet screwed for pipe or connections incl necessary packing union and cap complete all as specified and directed.

M&L for 75mm dia PVC(SWR)floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs CP Soap dish fixed with brass screws complete all as specified and directed.

S&F in repair stainless steel sinks made of 1mm thick (SS 304 Grade) overall size 495mmx420mm bowl size 410mmx330mmx160mm kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever barackets, waste coupling and connecting union to pipe complete all as specified and directed.

S&F in repiars stainless steel sinks with drainage board made of 1.00 mm thick (SS 304 Grade) overall size 915mmx460mm and each bowl size nexc 410mmx 330mm x 160mm for kitchen or laboratory with plugs,washer and wastes including bedding in cement mortar on to dwarf wall or incliuding supply & fixing cantilever brackets, waste coupling and connecting union to pipe complete all as specified and directed.

S & F in repairs Vitreous china squatting pan of pattern 'long pan' size 580 mm white with 'P' or 'S' trap front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan padestal pattern white, excluding fixing bolts, flushing cistern but including flush pipe,and PVC seat cover complete all as specified and directed.

Supply & fix in repair PVC valveless, 10 ltrs, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs Vitreous china WHB, white, flat back, of size 550mm x 400 mm including brackets, waste coupling 32mm, and waste Pipe, 32mm including pedastal complete all as specified and directed.

S&F in repair 125 mm brass CP shower Rose with arm complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connections complete all as specified and directed.

Repair to damage proof after complete removal existing treatment including padding, cleaning, the surface using wire brush brooming down and appplying the following treatment all as directed in order of precedence as stated:- (i) Rendering 15mm thick in Cm (1:4) on existing roof surface true to level after applying cement slurry @ 3Kg/Sqm. (ii) Applying one coat of bituminious primer . (Note :- Bituminous primer shall be 'TANK MASTIC' manufactured by M/s STP Ltd or "EMUFALTE" manufactured by M/s Texsa India Ltd or equivalent make as specfied in list of make) (iii) supply and laying 3mm thick APP based polymeric membrance of approved manufactured with weight not less than 3.00 Kgs Sqm reinforced with non-woven polyester febric weight not less than 150gms peer Sqm. Polymeric membrance shall be taken to a height of 3cm (minimum) and than inserted inside the groove of parapet wall and shall be finished by a membrance flashing. Note :- (i) Laying APP based polymeric membrance shall be done torch on method as per manufacturers instructions. (ii) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrance respectively and sealed all overlaps and joints as per manufacturers instructions.

S&F aluminium guide rail three track having two PVC wheel 50 mm dia for smooth functioning of cupboard/door shutter complete all as specified and directed.

S&F compacted recessed handle of size 150 mm suitable for sliding door complete all as specified and directed.

S&F Aluminium composite panel of 6 mm thick board ,interior grade ,both side with decorative choice lamination , fixed with screws to aluminum frame work complete all as specified and directed.

S&F Wooden brackets with wooden finished for 20 mm dia double rod , rollers etc wooden finished complete all as specified and directed.

S&F Wooden brackets with wooden finished for 20 mm dia single rod , rollers etc wooden finished complete all as specified and directed.

S&F decorative wooden finials with wooden finished complete all as specified and directed.

S & F in repairs Vitreous China EWC including seat cover closed pattern single piece size 755x365x655 complete all as specified and directed of make Jaguar Cat Part No :- LYS-WHT-38851PSM or equivalent make specified in list of make

S & F in repairs Towel rack 600mm long with lower hangers , stainless steel complete all as specified and directed. of make Jaguar Cat Part No:-AKP-35781PS or equivalent make specified in list of make

S&F in repairs vitreous China clay table top round shape WHB of make Jaguar Cat Part No:-OPS-WHT-15901N size 408x480x135 mm or equivalent make specified in list of make including waste coupling of Cat Part No:-ALD-727 or equivalent make specified in list of make complete all as specified and directed.

S&F in repairs Brass CP 2-in-1 Bibcock with flange complete all as specified and directed of make Jaguar Cat Part No:-ORP-10041PM or equivalent make specified in list of make

S&F in repair single lever tall body with 155 mm extension body fixed spout without popup waste system with 600 mm long braided hoses complete all as specified and directed. make Jaquar Cat Part No:- KUP-35005BPM or equivalent make specified in list of make

S&F in repairs 15 mm bore CP health Faucet cock with Flexible pipe 1 m long complete all as specified and directed. of make Jaguar Cat Part No:ALD-565 or equivalent make specified in list of make

S&F in repairs Soap dish holder complete all as specified and directed. of make Jaguar Cat Part No:-AKP-35731P or equivalent make specified in list of make

S&F in repairs Toilet roll holder with stainless steel flap complete all as specified and directed.of Make Jaguar Cat Part No:- AKP-35753PS or equivalent make specified in list of make

S&Fin repairs Towel ring sqare shape stainless steel complete all as specified and directed. of Make Jaguar Cat Part No:-AKP-35721P or equivalent make specified in list of make

S&F in repairs corner glass shelf with bracket complete all as specified and directed. of make Jaguar Cat Part No:ACN-1173 or equivalent make specified in list of make

S&F Mirror Cabinet of size 622 x 422 mm (partition boxes - 06 Nos) complete all as specified and directed. of make Prayag (Symet) cat part No : 555 or equivalent make specified in list of make

S&F in repairs CP over head shower square shape single flow with rubit cleaning system of size 200x200mm (SS Body & face plate with cromium finish) complete all as specified and directed. of make Jaquar cat part No:OHS-CHR-1619 or equivalent make specified in list of make with CP shower arm of size 400x25x25 mm square shape for wall mounted showers flange of make Jaquar Cat par No-SHA-455L400 or equivalent make specified in list of make

S&F in repairs CP single lever wall mixer 3-in-1 system with provision for bath hand shower & overhead shower complete with 115 mm long bend pipe connecting legs & wall flange (without hand & over head shower) complete all as specified and directed. of make Jaquar cat part No:OPP-15125PM or equivalent make specified in list of make

S&F CP Hand shower 27x27 mm sqaure shape single flow with Air effect (ABS body & face plate chrome plated) with Rubit cleaning system complete all as specified and directed. of make Jaquar cat part No:HSH-35537 or equivalent make specified in list of make with flexible tube in chrome finish 1.5 m long with nuts of make Jaquar cat part No:SHA-571 or equivalent make specified in list of make

S&F in repairs CP wall mixer with provision for overhead shower complete with 115 mm long bend pipe on upper side connecting legs & wall flange complete all as specified and directed. of make Jaquar cat part No:FUS-29273UPR or equivalent make specified in list of make

S&F in repairs lever sink mixer with swinging spout on upper side (wall mounted model ) with connecting legs & wall flanges complete all as specified and directed. of make Jaquar cat part No:LYR-38165 or equivalent make specified in list of make

S&F stainless steel drawer box of size 460mm x 450mmx 675mm and 14 guage thick of any colour with provn for double rail rolling system complete all as specified and directed.

S&F plain stainless steel basket made out of 6mm durable wire of high quality stainless steel of size 420x485x200mm complete all as specified and directed.

S&F plain stainless steel cup & saucer basket made out of 6mm durable wire of high quality stainless steel of size 520x585x100mm complete all as specified and directed.

S&F plain stainless steel perforated cutlery basket of size 470x485x100mm complete all as specified and directed.

S&F plain stainless steel grain trolley made out of 6mm durable wire of high quality stainless steel of size 525x485x350mm complete all as specified and directed.

S&F plain stainless steel thali basket made out of 6mm durable wire of high quality stainless steel of size 470x485x200 complete all as specified and directed.

S&F ball bearing drawer channel (soft close) of size 600 mm long x 45mm width complete all as specified and directed.

S&F clip on cabinet hinge(auto close) complete all as specified and directed.

S&F Stainless steel kitchen plate rack of size 31" X 30" X 10" made out of stainless steel sheet of 1.00 mm with all accessories including taking down old unservicable rack complete all as specified and directed.

S&F Stainless steel kitchen plate rack of size 24" X 24" X 10" made out of stainless steel sheet of 1.00 mm with all accessories including taking down old unservicable rack complete all as specified and directed.

S&F in repairs peg set of six, chromium plated, back plate including chromium plated fixing screw complete all as specified and directed.

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete including fittings such as switches, sockets, ceiling rose, pendent holders etc. and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified and directed.

Taking down existing energy meter and refixing the same after completion on the original location all work complete all as specified and directed.

Taking down existing water heater of any capacity and deposit the same to MES store complete all as specified and directed.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded HFFR copper conductor in PVC conduit with cable 1.5 Sqmm size 1100 volts grade conforming to IS:694 and terminate to flush box of required size suitable mounting modular switches and sockets including single core multi stranded HFFR copper conductor 1.5 Sqmm PVC insulated cable as earth wire connected to earth and common earth dolly drawn in same concealed conduit all as specified and directed by Engr-in-charge for One light point controlled by one no, one way 6 Amp switch complete all as specified and directed.. Note :- Cutting chases for concealed conduit wiring for the following points and making good in cement mortar is deemed included in unit rate.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded HFFR copper conductor in PVC conduit with cable 1.5 Sqmm size 1100 volts grade conforming to IS:694 and terminate to flush box of required size suitable mounting modular switches and sockets including single core multi stranded HFFR copper conductor 1.5 Sqmm PVC insulated cable as earth wire connected to earth and common earth dolly drawn in same concealed conduit all as specified and directed by Engr-in-charge for One fan/exhaust point controlled by one no, one way 6 Amp switch complete all as specified and directed.. Note :- Cutting chases for concealed conduit wiring for the following points and making good in cement mortar is deemed included in unit rate.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded HFFR copper conductor in PVC conduit with cable 1.5 Sqmm size 1100 volts grade conforming to IS:694 and terminate to flush box of required size suitable mounting modular switches and sockets including single core multi stranded HFFR copper conductor 1.5 Sqmm PVC insulated cable as earth wire connected to earth and common earth dolly drawn in same concealed conduit all as specified and directed by Engr-in-charge for One light point controlled by 2 two way 5 Amp switches complete all as specified and directed.. Note :- Cutting chases for concealed conduit wiring for the following points and making good in cement mortar is deemed included in unit rate.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded HFFR copper conductor in PVC conduit with cable 1.5 Sqmm size 1100 volts grade conforming to IS:694 and terminate to flush box of required size suitable mounting modular switches and sockets including single core multi stranded HFFR copper conductor 1.5 Sqmm PVC insulated cable as earth wire connected to earth and common earth dolly drawn in same concealed conduit all as specified and directed by Engr-in-charge for One bell/buzzer point controlled by one bell push complete all as specified and directed.. Note :- Cutting chases for concealed conduit wiring for the following points and making good in cement mortar is deemed included in unit rate.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded HFFR copper conductor in PVC conduit with cable 1.5 Sqmm size 1100 volts grade conforming to IS:694 and terminate to flush box of required size suitable mounting modular switches and sockets including single core multi stranded HFFR copper conductor 1.5 Sqmm PVC insulated cable as earth wire connected to earth and common earth dolly drawn in same concealed conduit all as specified and directed by Engr-in-charge for One three pin 5 Amp socket outlet point controlled by one no, one way switch on same board complete all as specified and directed.. Note :- Cutting chases for concealed conduit wiring for the following points and making good in cement mortar is deemed included in unit rate.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded HFFR copper conductor in PVC conduit with cable 1.5 Sqmm size 1100 volts grade conforming to IS:694 and terminate to flush box of required size suitable mounting modular switches and sockets including single core multi stranded HFFR copper conductor 1.5 Sqmm PVC insulated cable as earth wire connected to earth and common earth dolly drawn in same concealed conduit all as specified and directed by Engr-in-charge for One three pin 5 Amp socket outlet point controlled by one no, one way switch on independent board complete all as specified and directed.. Note :- Cutting chases for concealed conduit wiring for the following points and making good in cement mortar is deemed included in unit rate.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded HFFR copper conductor in PVC conduit with cable 4.0 Sqmm size 1100 volts grade conforming to IS:694 in new metal flush box of 1.6 mm thick including one coat of syenthetic enamelled black paint with new modular white cover plate with frame of suitable size of required colour fixed with brass screws and cup washers including single core multi stranded HFFR copper conductor 4.0 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit for Modular AC Box Metal box, power socket Indepentent board complete all specified and directed. Note :- Cutting chases for concealed conduit point wiring and making good in cement mortar is deemed included in unit rate..

S&F switch 6 Amps modular type, 1M with red indication, single pole one way, ISI marked complete all as specified and directed..

S&F bell push, modular type,1 Module 5 amps complete all as specified and directed.

S&F switch 6 Amps modular type, 1 Module with red indication,single pole, two way 5/6 amps complete all as specified and directed.

S&F modular socket 6 Amps ,5 pin combined modular type 2 Module, shuttered type, ISI marked complete all as specified and directed..

S&F modular socket 6/16 Amps 6 pin combined modular type 2 Module, shuttered type , ISI marked complete all as specified and directed..

S&F switch 16 Amp rating Modular type, 1 Module, one way switch complete all as specified and directed.

S & F Modular cover plate with frame & flush box of 8 modules, complete all as specified and directed.

S & F Modular cover plate with frame & flush box of 6 modules, complete all as specified and directed.

S & F Modular cover plate with frame & flush box of 4 modules, complete all as specified and directed.

S & F Modular cover plate with frame& flush box of 3 modules, complete all as specified and directed.

S & F Modular cover plate with frame & flush box of 2 modules, complete all as specified and directed.

S & F Modular cover plate with frame & flush box of 1 module, complete all as specified and directed.

S&F ceiling rose 3 terminal / PVC insulated body ISI Marked complete all as specified and directed.

Supply and fixing call bell ding dong, AC, 230 V, Single pole ISI marked complete all as specified and directed.

Supply Installation and testing in repair of intregral LED 4ft luminaire of CRCA / extruded aluminium housing and PC diffuser (Diffuser-Non yellowing type). The luminaire should have a 20Watt LED with colour consistency SDCM< 5,CRI> 80 and colour temperature - 4000 to 6500K, Luminaire shall be desihned to emit at least 2000 nominal lumens at a system efficacy of at-least 120 lumen/watt, power consumption should not be more than 18W (+5%). the life of fixture (including Driver): 50000 burning Hrs.@ L70B50 Lumen maintenance @ design ambient temp 50 deg C. The electronic driver used shall have a power factor >0.95 and THD < 10% suitable for an operating voltage range of 150-270V AC current Ripple<5% internal surge protection should be minimum 2.5KV, electrical insulation class should be Class I &driver should be of class B serviceablility. The luminaire should be at least IP20 & IK02 rated. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have in house NABL accredited lab conduct LM79, type test as per IS10322 & "FAT" before dispatch as per IS 10322.The contractor must submit the NABL accreditation certificate for Luminaire manufacturer along with sample approval. The LED Luminaire & It's driver both should be BIS registered successful bidder shall submit the following reports before supply of material for approcals LM79 issued by NABL accrediated lab, LM80 issued by LED manufacturer type test certificate for luminaire as issued by NABL accrediate lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Driver complete all as specified and directed.

Supply Installation and testing in repair of Integral / batten LED 2ft, 10 watt 220 V, luminaire made of CRCA / extruded aluminium housing and PC diffuser (Diffuser-Non yellowing type). The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit at least minimum 2000 system lumens at a system efficacy of at-least 120 lumen/watt. Power consumption should not be more than 10W (± 5%). The Life of fixture (Including Driver):50000 burning Hrs. @ L70B50 Lumen maintenance @ design ambient temp 45 deg C. The electronic driver used shall have a power factor 0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, Current Ripple ≤ 5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I & driver should be of Class B serviceability. The luminaire shall be IP20 & IK02 compliant. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322 & "FAT" before dispatch as per IS 10322. The contractor must submit the NABL accreditation certificate for Luminaire manufacturer along with sample approval. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accrediated lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accrediate lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Driver.

Supply & fix lamp holder, PVC/polycarbonate type with back plate straight or angular suitable for batten fittings complete all as specified and directed..

Supply & fix in replacement for LED type wall mounting light fitting suitable for 9-20 W, housing glass, frosted type, metallic frame complete all as specified and as directed.. Make- Philips Cat Part 3145320 Watts Light or equivalent make specified in list of make

S&F LED Bulb of 9 watt Oval diffuser to give glare free light, IP50 of lumen output should be greater than 1100 lumen, CCT 4000-5700, CRI>=70, THD must be less than 10%, Power factor more than 0.9, working voltage 140-270V, life time should not be less than 25KHr complete all as specified and as directed..

S & F Surge Protection Device (SPD) single phase, 230 Volt, 50Hz, T2 -limp, Imax 20 KA per pole complete fixed in distribution board and making connections complete all as specified and directed

S&F Hot water storage (Geyser) 25 Ltrs capacity ,BEE 5 star rated, vertical type, digital temperature display with suitable size of fastner and incl provision and connecting up of ss braided pipe with adopter for inlet and outlet water connection, copper element corrosion resistance antiscaling magnesium anode, having adjustable knob for temperature control and inner tank material of superior glassline coating / percelain Enamel Coating / Titanium Enamel Coating / Nano Blue Diamond Glass Coating / Coating with Single Weld line tank and outer body material ABS with high pressure with standing capacity upto 8 bar presuure, Multiple safety systems for protection against dry heating, overheating and over pressure,IPX4 waterproof technology for longer product life having heating element 2 KW and minimum two year warranty on product, minimum 3 years warranty on heating element & 5 years on tank complete all as specified and directed. .

M & L for cutting of circular hole at any type of wall suitable size for fixing of exhaust fan of size 300/250mm sweep, grouting 04 Nos 100mm long 12mmdia stud bolt including, making good to disturbed surfaces of wall to match as per existing colour complete all as specified and directed.

M & L for testing, instatllation, commissioning of Kitchen Exhaust System Filter Less and Dry Heat Clean Technology | Matt Black Finish, Hassle free Filter Less and Dry Heat Auto Clean Technology, Thermostatic Touch Control Panel with 3 Speed Gesture Motion, including, Matt Black Finish, Black Metal Oil Collector,Motor with Copper Winding, Black Glass Clad Hood with LED Insignia, Front Panel with Black Glass, Energy Saving LED Light,Metal Blower + Metal Housing, Designed Air Flow (max): 1250 Nm3/h, Noise Level: 58 dBA (max), Lifetime Warranty, Size: 90 Cm complete all Civil work for fixing system, , make hole and replastering existing wall with wall colour coding with Basic Civil work required including fixing of Duct and complete Electrical wiring. as reqruied for system running complete all as specified and directed.

S&F Exhaust fan 300 mm sweep, copper winding, metal body, four metal blades BEE approved/ISI marked, air delivery shall not be less than 1600 CMH at 1400 RPM, mounted in suitable opening arrangement with louvers shutters, suitable for operation on 240 volt, single phase, 50 cycle per second, AC supply and connecting up using flexible cord wire 3 core using PVC flexible conduit from ceiling rose or connector to fan to cover PVC cable fixed in position as recommended by manufacturer complete all as specified and directed..

S&F Exhaust fan fresh air venatilation fan, self closing louver, 250mm sweep, PVC body - Square type, speed 1300 RPM, Air delivery not less than 780 CMH suitable for operation on 240 volt, single phase, 50 cycle per second, AC supply and connecting up using flexible cord wire 3 core using PVC flexible conduit from ceiling rose or connector to fan to cover PVC cable fixed in position as recommended by manufacturer complete all as specified and directed..

S & F 32mm dia GI tubing light grade bracket all over 1.2 mtr lengthwith cutting as required and bend to shape with flat iron clamp of size 32mm 2 nos suitable size nut and washers complete for street / Bldg security light fittings taking down Unsv/ fully rusted existing unsv one complete all as specified and directed..

S & F in replacement of LED street light fitting of 20 Watt high-quality group control enabled integrated LED Street Light with a minimum system lumen of 2000 lm and system wattage not exceeding 20W with a nominal system efficacy of 110 lumen/watt. The LED used shall have CCT of 5700K, SDCM ≤ 5 and CRI≥70. The housing should be made of LM6/ADC12 Alloy, non-corrosive Single Piece pressure die-cast aluminum, to withstand extreme environments. The spigot shall be part of “Single Piece Pressure Die-cast housing” & shall not be bolted to the luminaire housing to ensure robust design. The name of the brand should be embossed/engraved & should not be mentioned using sticker/screen printing. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. The luminaire LED shall have declared Lifetime of 75K hours@L70. The product should be designed for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP66 & impact resistance shall be IK10. Control gear compartments shall be Top maintainable without accessing/opening the optical compartment. The Luminaire should have a minimum 20 KV/10KA SPD duly bolted in the Luminaire. The SPD should be able to sustain a minimum 15 hits of 10KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The luminaire should be of Class B Serviceability. The LED used in the luminaire shall be SMD type only & shall be from either Lumileds, Osram, Nichia, Cree & APT Electronics make or equivalent. The Driver should be asphalt potted & should be a BIS approved driver. The driver shall have operating voltage of 120V to 270V, PF≥0.95 @ full load, THD≤10% @ full load. The driver should be capable of withstand voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V(±15V) and have an auto recovery feature. The driver shall comply to IEC61547 & IEC 61000-3-2. The luminaire driver & it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322 & "FAT" before dispatch as per IS 10322. The contractor must submit the NABL accreditation certificate for Luminaire manufacturer along with sample approval. The LED Luminaire & it's driver both should be BIS registered. The contractor shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test report for luminaire as issued by NABL accredited lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire & Driver complete all as specified and directed.

Supply and fix in replacement MCB DB 4 way TPN sheet metal enclosure suitable for fixing MCB of appropriate capacity as incomer and SP for outgoing ,415 volts, 50 Hz, with IP-43 protection, double door with 100 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting including taking down complete all as specified and directed. . (Note : MCB SP/MCB shall be measured and paid seperately under appropriate items of this schedule . Note : Copper thimble shall be used for connection of cable .

Supply and fix in replacement MCB Distribution board, 240 volts single pole and neutral,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed.

Supply and fix MCB 4 pole, 40 Amps, 16KA breaking capacity 415 Volts complete all as specified and directed including taking down old one complete all as specified and directed

Supply and fix MCB 4 pole, 63 Amps, 16KA breaking capacity 415 Volts complete all as specified and directed including taking down old one complete all as specified and directed

Supply and fix RCBO with earth leakage, over load and short circuit proptection, DP, 240 Volts, 32 Amps, 30 mA senstivity, 4 Module complete all as specified and directed including taking down old one complete all as specified and directed

Supply and fix MCB, Single pole, 240 Volts, 6 to 32 Amps capacity, 10 KA, ‘C’ Curve fixed complete all as specified and directed

Supply and fix MCB 4 pole, 32 Amps, 16KA breaking capacity 415 Volts complete all as specified and directed

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded HFFR type 1100V grade 4 x 6 sqmm complete drawn in new PVC conduit of min dia 20mm and its accessories along with 1x 6 sqmm PVC insulated unsheathed copper conductor multi stranded HFFR type cable for continuous earth wire and duly connected to common earth dolly including taking down old unsv sub main wiring complete all as specified and directed Note :- (i) Cutting chases for concealed sub main wiring for the following points and making good in cement mortar is deemed included in unit rate (ii) Two single core cable and one No. earth wire and one run of conduit shall be measured together as one length

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded HFFR type 1100V grade 2 x 4 sqmm complete drawn in new PVC conduit of min dia 20mm and its accessories along with 1x 4 sqmm PVC insulated unsheathed copper conductor multi stranded HFFR type cable for continuous earth wire and duly connected to common earth dolly including taking down old unsv sub main wiring complete all as specified and directed Note :- (i) Cutting chases for concealed sub main wiring for the following points and making good in cement mortar is deemed included in unit rate (ii) Two single core cable and one No. earth wire and one run of conduit shall be measured together as one length

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded HFFR type 1100V grade 2 x 6 sqmm complete drawn in new PVC conduit of min dia 20mm and its accessories along with 1x 6 sqmm PVC insulated unsheathed copper conductor multi stranded HFFR type cable for continuous earth wire and duly connected to common earth dolly including taking down old unsv sub main wiring complete all as specified and directed Note :- (i) Cutting chases for concealed sub main wiring for the following points and making good in cement mortar is deemed included in unit rate (ii) Two single core cable and one No. earth wire and one run of conduit shall be measured together as one length

Material and labour for earthing in replacement complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I. all as specified and directed

Supply and fixing/laying 40mm bore, steel tubings, galvanised, light grade with all fitting laid across road , in trenches or across PCC drain or along electric pole or floor/wall etc for protection of cable complete all as specified and directed.

Supply & laying Sand coarse dry as in cushioning of underground electric cable in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable ) and gently punned down to 18cm thickness all complete as specified and directed. Note :- Only punned down sand shall be measured.

M&L for Bricks; common burnt clay building bricks, sub-class ‘B’ designation 75 locally available laid dry width wise across the line of cable in trenches for protection of UG cable complete as specified and directed.

Supply, lay in trenches, floors, fix on wall/pole, passing through pipes etc., LT UG cable, 1100 volts grade, PVC/ XLPE insulated , with multistranded aluminium conductors, armoured with galvanised steel wire or tape ,gland, lugs etc, of size 25 Sqmm 4 core, confirming to IS specifications including taking down of old existing unserviceable UG cable complete as specified and directed.

N.K.TRADING COMPANY (BID ID -3076932)