Construction of Auditorium at Kajalgaon, Chirang District, BTC, Assam. TN_29_1

Amount

CIVIL WORKS Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. 2.28.1 All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.8.1 All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand(zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane Emulsifiable concentrate of 20%.

Diluting and injecting chemical chemical emulsion for POST CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) Treatment of soil under existing floors using chemical emulsion @ one ltr. Per hol, 300mm apart including drilling 12mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor. With Chlorpyriphos /Lindane E C. 20% with 1% concentration.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand including finishing the top smooth

Centring and shuttering including strutting, propping etc. and removal of form for: 5.9.1 Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, posts and Struts

Weather shade, Chajjas, corbels etc., including edges

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in foundation & plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand)

Extra for providing and placing in position 2 Nos. 6 mm dia MS bars at every third course of half brick masonry (with FPS bricks)

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand )

12mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)

Providing & fixing in position Phenol bonded Bamboowood flooring with planks of sizes 14mm thick, minimum 1800mm length and minimum 100 mm wide, in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded polyethylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm x 44mm, wherever required. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size Size of Tile 600 x 1200 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 11.41A.3.1 Size of Tile 600 x 600 mm

Providing and laying vitrified Wall tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red 8.2.2.1 Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 8.3.2 Granite work

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 26.86.7 Frame size 65 x 150 mm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters.The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge,with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 1mm made out of 1.6mm thick G120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual),symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos.M.S.angles of size 35x35x5 mm to a vertical post made up to M.S.Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes,angles flats, providing & fixing M.S. message plate of required size,steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge. Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47x50 mm & mullion 47x68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm).

Gutter (600 mm over all girth)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length 1200 mm and secondaryintermediate cross-T of size 24x32 mm of length 600mm to formgrid module of size 600 x 600 mm, suspended from ceiling usinggalvanised mild steel items (galvanizing@ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The workshall be carried out as per specifications, drawing and as per directionsof the Engineer-in-Charge. With 15 mm thick tegular/butt edged without perforation plain/designer light weight calcium silicate Anti-Microbial Bio-Safe coated false ceiling tiles Confirming to JIS-Z2801 and ASTM G-21

Providing and fixing stainless steel ( grade 304 )railing made of Hollow tubes , channels , plates etc , including welding grinding , buffing ,polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete ,I/c fixing the railing with necessary accessories &stainless steel dash fasteners ,stainless steels bolts etc ,of required size ,on the top of the floor or the side of waist slab with suitable arrangment as per approval of Engineers -in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accesories such as nuts ,bolts, fasteners etc

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface Water thinnable cement primer

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with "Silicone additives of required shade New work (two or more coats applied @1.43 ltr/10 sqm over and including base coat of water proofing cement paint applied @2.20kg/10sqm)

Outer face: Outer face having 6mm thick fiber cementboard fixed on 9mm thick fiber cement board, Type A, as per IS:14862:2000 (high pressure steam cured) Inner Face :- 12.5 mm thick gypsum plaster board conforming to IS 2095:2011 fixed on 8 mm thick fibre cement board confirming to IS:14862:2000 of type B (High pressure steam cured)

Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Marine plywood conforming to IS: 710

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete: 250x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed toreqired colour or shade with necessary screws etc. 200x10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with necessary screws etc. complete: Twin rubber stopper

Providing & fixing IS:3564 marked aluminium Die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 100X58X1.90 mm

SANITARY & WATER SUPPLY WORKS Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fittings and brackets cutting & making good the walls, wherever required White vitrious china wash basin size 630 x 450mm with a pair of 15mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 225 mm

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge

Providing & fixing 100 mm sand cast iron grating for gully trap

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10 mm gap for thermal expansion i) single socketed pipe 75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm

Single tee without door 75x75x75 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 75 mm Shoe

110 mm Shoe

Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore Each

25 mm nominal bore Each

Providing and fixing gun metal non- return valve of approved quality (screwed end) 32 mm nominal bore Vertical

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 40 mm nominal bore

Providing and fixing square - mouth SW gully trap grade 'A' complete with CI grating brick masonry chamber with water tight CI Cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50 Kg) and frame to be not less than 2.70 Kg as per standard design. 100x100mm size 'P' type With FPS bricks class designation 7.5

Constructing brick masonary manhole in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), fondation concrete 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregated 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90 x 80 cm and45cm deep including CI cover with frame (light duty ) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg) (weight of the cover 23 kg and weight of frame 15 kg). With FPS bricks with class designation 75

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing hand shower (Health faucet) with 1.2mtr long with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 litre per minute at 3 bar in chrome finish and wall hook. ( MAKE-1: JAQUAR, MODEL NO. HEALTH FAUCET : HSH-CHR-1655)

Supplying fitting and fixing C.P bib cock 15 mm dia of approved brand as directed and specified (G.I & C.P pipes will be measured separately). Jaquar make (a) Continental / clarion (iii) 2-Way bib cock

Providing and fixing white vitreous Rimless Bliend installation Wall Hung WC with UF soft close seat cover, hinges, fixing accessories and accessories set size 355X525X380mm. For VVIP Toilet Model number : Jaquar DRS-WHT-37953BIUFSM

Providing and fixing Single Piece Slim Concealed Cistern With Wall Mounting Frame, Installation Kit And “S-Type” Drain Pipe Connection Set For Wall Hung Wc all complete. (Without Flush Control Plate) Model number : Jaquar JCS-WHT-2400WS

Providing and fixing Flush Control Plate for concealed cistern. Model number : Jaquar JCP-CHR-102415

Providing and fixing white vitreous Counter Top Basin with CI brackets, cutting and making good the walls wherever require: For VVIP Toilet Model number : Jaquar ALS-WHT-85601

Providing and fixing CP waste coupling 32mm Size Full Thread with 80mm height all complete. Model number : Jaquar ALD-CHR-705

Providing and fixing CP Single Lever Tall Boy with 125mm Extension Body Fixed Spout without Popup Waste System with 600mm Long Braided Hoses all complete. For VVIP Toilet Model number : Jaquar Alive ALI-85005B

Providing and fixing CP Piller Cock auto closing system with 600mm Long Braided Hoses all complete. For common area Toilet Model number : Jaquar PRS-CHR-031

Providing and fixing CP Sink Cock with Regular Swinging Spout (Wall Mounted Model) with Wall Flange, complete in all respect.. Model Number Jaquar FLR-CHR-5347N

EXTERNAL WATER SUPPLY WORKS (BORING) Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings& accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing Bail plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 40 mm nominal outer dia. Pipes.

Providing and placing in position filters of 40 mm diameter G.I. pipe with brass strainer of approved quality.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall. 25 mm dia. nominal bore

SEPTIC TANK Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size derived fro natural resources)

Brick work with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in foundation & plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:3 (1 cement :3 coarse sand)

Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement 18mm thick

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 0.91 m deep with S.F .R.C. cover and frame (heavy duty , HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

ELECTRICAL WORK SH:-I Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A

Group B

Group C

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X6 sq. mm earth wire

2 X 10 sq. mm + 1 X6 sq. mm earth wire

Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete as required.

WIRING IN PVC CONDUIT (Power Point) Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.as required. 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

12 Module (200mm X 150mm)

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. (for Hi-wall AC)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

TV antenna socket outlet

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

SH:-II (MCB DBs) (SCHEDULE ITEM) Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

double pole

Triple pole and neutral

SH:-IV (EARTHING) (SCHEDULE ITEM) Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories,and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm), Double run

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

SH:-V (LIGHTNING CONDUCTOR) Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.( provide 3 meter GI pipe

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting / sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

SH-VII (CABLE AND CABLE TRAYS) (SCHEDULE ITEM) Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3.5Cx300 SQ.MM. AL. AR. XLPE CABLE

3.5Cx120 SQ.MM. AL. AR. XLPE CABLE

3.5Cx95 SQ.MM. AL. AR. XLPE CABLE

3.5Cx50 SQ.MM. AL. AR. XLPE CABLE

4Cx10 SQ.MM. CU. AR. PVC CABLE

2Cx10 SQ.MM. CU. AR. PVC CABLE

Cable laying in ground Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Cable laying on surface Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Cable laying through pipe MS perforated cable tray Hot Dipped Galvanized 150 X 50 X 1.6 mm

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying with fitting fixing of surface & wall mounted LED luminaries complete with all accessories including driver directly on wall / ceiling including connection with 1.5 sq mm P.V.C. insulated S.C.copper conductor as required and as directed by the department. (Crompton/PHILIPS/ BAJAJ/ Havells or equivalent considering the mother items rate and specification) 18W 4ft LED Batten

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. (Bajaj or equivelent make) high speed 300MM SWEEP METTALIC .

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required RJ 45 LAN Socket outlet, Legrand make

Supply , Installtion , Testing and comissioning of 6 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts.

Supply , Installtion , Testing and comissioning of unloaded 24 port CAT6 patch / jack panel for CAT6 cable termination.

Supply , Installtion , Testing and comissioning of 24 port loaded LIU with adaptor plates , pigtel cables for connections

Supply , Installtion , Testing and comissioning of CAT6 patch cord 1 Mtr for rack side switch termination.

INDOOR AREA LIGHT SITC of 18W 2000lm deep-recessed non dimmable LED downlight. (Similar as Philips Model no-DN296B LED20S-6500 PSU WH or equivalent approved make)

SITC of 18W 2000lm surface mount non dimmable LED downlight. (Similar as Philips Model no- SM251C LED20S- 6500 PSU WH or equivalent approved make)

SITC of RD Series Pendant with 14W LED Bulb, 100% recyclable PC made customisable pendant luminaire suitable with retrofit LED lamps (Philips or equivalent approved make)

SITC of 18W 2000lm Controlled Beam (45/60deg) ultra deep-recessed antiglare (UGR<19) LED downlight. (Similar as Philips Model no.- DN590B M LED20S-6500 PSU WH MB or equivalent approved make)

SITC of 23W 2600lm recessed Extruded Al housing 4ft linear non-dimmable LED luminaire having 60mm width and downlight distribution. (Similar as Philips Model no.-RC780B LED26S-6500 PSU W6L120 OD SI or equivalent approved make)

HALL AREA LIGHT SITC of 18W 2000lm Controlled Wide Beam (60deg) ultra deep-recessed Al housing antiglare (UGR<19) DALI dimmable 4000K LED downlight- (Similar as Philips Model no.-DN590B M LED20S-4000 PSD WH WB or equivalent approved make)

SITC of RD Series Pendant with 14W LED Bulb-IP 20 Rated , 3D Printed Pendant Luminaire made of recyclable 100% Virgin Polycarbonate and available with choice of essential colors , primary colors and shiny metallic colors with a possibility of printing Log

SITC of DALI dimmable driver (Philips or equivalent approved make)

EXTERNAL LIGHT SITC of Double Head outdoor type LED wall-washer (Similar as Philips Model no.-58160 or equivalent approved make)

SITC of 8W 500lm IP65 IK10 Die Cast Al housing 800mm long 3000K LED Bollars (Similar as Philips Model no.-BCP151 LED150/WW PSU 220-240V 7043 BOLLARD or equivalent approved make)

DIESEL GENERATING SETS Supplying installation testing and commissioning of silent type D.G. Set, AMF Panel, Bus Trunking /cables from DG Set to essential panel, control cable, Earthing of DG Set and AMF Panel, DG set exhaust piping as per CPCB norms and minor allied works. Including Extra for synchronizing panels wherever required.

Supplying including installation, connection., testing and commissioning of SUBMERSIBLE PUMP SET along with control/starter panel complete as directed and specified by the deptt. Three phase Submersible motor pump set (Delite/ KSB/ Texmo / Crompton Greaves/ CHETAK/Aquatic/ CRI/ V-Guard) suitable for 100 mm bore well and above. 2 HP Submersible motor pump set and control panel.

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoordoor type floor mounting compartmentalize LT MAIN PANNEL BOARD of made of 16 SWG (1.66 mm) thick C.R. sheet and required size angle having 4 nos legs at the bottom complete neatly wiring done with provision for100a 4P MCCB one no as incomer and out going as specified and directed by the deptt. confirming to IP 65 protection comprising of the following electrical items.

3 KVA UPS, 1ph In/1ph Out, 15 min back-up, APC/NUMERIC/EMERSON FOR CCTV

FIRE FIGHTING WORK Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Upright Sprinkler

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required . 1000 mm

Providing and fixing of carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase ingernal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming ro IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with internal charge.. Capacity 4.5 Kg.

Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with inernal charge. 6kg.Capacity

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 80mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 40mm dia

50mm dia

65mm dia

80mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

5 HP three Phase vertical multistage high pressure centrifugal pump set 10 stage (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

ROAD WORKS Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

75 mm thick back filling for pitching including supplying of required materials and consolidation etc. complete with : Moorum

Centring and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

FURNITURE WORKS Supply and installation of Reception Desk (Model-Reflection Reception Desk) 2400Wx1770Dx740H As Per Direction Of Engineer In Charge

Supply and installation of Office Chair (Leatherette) Model-Marvel High Back As Per Direction Of Engineer In Charge

Supply and installation of Cabinet (Model-Glass Door Storwel) As Per Direction Of Engineer In Charge

Supply and installation of Waiting Chair (Model- Traverse 3 seater with two arms) As Per Direction Of Engineer In Charge

Supply and installation of Table Size-1665x900x750 As Per Direction Of Engineer In Charge

Supply and installation of Arm Chair Marvel Visitor As Per Direction Of Engineer In Charge

Supply and installation of Center Table As Per Direction Of Engineer In Charge

Supply and installation of Sofa (Model- Orlando(3+1+1) Fabric/ Synthetic Leather) As Per Direction Of Engineer In Charge

Supply and installation of Wardrobe Adriana 2 door (Model- Auratine - Steel) As Per Direction Of Engineer In Charge

Supply and installation of Side Table (Model- Bloom corner table) As Per Direction Of Engineer In Charge

Supply and installation of Projector Room Table (Model- Mingle Unitized Mem 10 Seater) As Per Direction Of Engineer In Charge

Supply and installation of Projector Room Chair As Per Direction Of Engineer In Charge

a) Auditorium Chair : Supply , fitting & fixing in position push back Auditorium chair of approved modle & make.Auditorium chair : supplying & Placement of Auditorium Chair from ISO 9001:2015,ISO 14001,OHSAS 18000, BIFMA, AIOTA,Greenguard Certificate Manufacturers and as per approved drawing & design / specification of Engineer – in – charge. The seat and back shall be made up of 1:2 cm, thick hot pressed plywood measured and shall be upholstered with fabric and molded polyurethane foam. The seat shall be mounted on seat brackets made of 0.5 t 0.05 cm , thk HR steel, The seat shall be tip-up type and can be folded when not in use. The size of back shall be 47.0 cm, (W) x 52.0 cm, (H) and of seat shall be 47.0 cm, (W) x 44.0 cm, (D) . The HR polyurethane foam shall be moulded with density = 45+/- 2 kg/m3 and hardness load 16 ± 2 kgf as per 15:7888 for 25% compression. The arrnests shall be membrane – pressed ( Cherry shade ) MDF with black backing laminate. The understructure shall be fabricated using of rectangular M.S.E.R.W. tube 5.08±0.03 cm x 2.54 ± 0.03cm x 0.16 ± 0.0128 thk , welded with back fixing brackets made of 0.315 ± 0.022 thk, CR steel . The frame shall

b) Auditorium Chair : Supply , fitting & fixing in position Premium Leather Auditorium Recliner Chair With Writing Pad & Cup Holder : supplying & Placement of Auditorium Chair from ISO 9001:2015,ISO 14001,OHSAS 18000,BIFMA,AIOTA,Greenguard Certificate Manufacturers and as per approved drawing & design / specification of Engineer

STAGE CRAFT LIGHT Light Bars, Wiring, Lighting Fixtures:, DMX & Controls: SITC of MS pipe Lighting Bar (fixed): to be provided on stage - to be fixed from the existing main structure Girder/Grid/Beams/Ceiling,; approx. size 12m x 50mm dia B-class, MS PIPE supported by A.I. brackets; duly painted black

SITC of MS pipe Lighting Bar (fixed): to be provided at FOH position - to be fixed from the existing main structure Girder/Grid/Beams/Ceiling, approx. size 12m x 50mm dia B-class, MS PIPE supported by A.I. brackets; duly painted black

SITC of MS pipe Side Light "Ladder" brackets: with 3-sections, to be provided on either sides for Side Lights - using 1.5" square MS Tube; to be fixed from the existing main structure Girder/Grid/Beams/Ceiling; approx. size: 4ft.x 2ft.; duly painted black

SITC of WIRING for DMX Points: using 07 sqmm falcon FR wire with common xir.

SITC of customized MCB Box for 36way with 100amp Isolator, Power indicator bus bar, volt meter, 20amp MCB. The MCB's/ Isolators should be of Legrand (Laxic)/ L&T (Exora)/Crabtree (Xpro)/ Schnider (Acti-9)/Hager

SITC of WIRING for DIRECT Points: using 1.5 sqmm 4 core FINOLEX FRP wire with starting from the patch panel (side of stage) to the motorized curtain. terminated at junction box

SITC of WIRING for DIRECT Points: using 1.5 sqmm FINOLEX FRP wire with common neutral & earth for 2 sockets starting from the patch panel (side of stage) to the Lighting bars/tree or stage points, terminated at junction box with 2 x 3-pin CEE 16 Amp. modular sockets; cabling laid in PVC conduits STAGE TO STAGE

SITC of Pearl-1024 DMX Lighting Desk: 240 Intelligent Fixtures + 240 Dimmer Channels: 96 Channels; Load and Save shows with USB: Theatrical Plotting & Playback functions; Shape Generator: 15 Playback Masters controlling 450 memories, chases or cue lists MIDI and Sound to Light triggers: VGA output; supplied with LEd lamp

SITC of DMX Data Splitter: 1 x IN to 8 x OUTPUT DMX-512 Data Splitter Unit, suitable both for Dimmer & Intelligent Lights; Model: SP-81

SITC of Inter connection - DMX Data patch cables, for interlinking Intelligent Lighting Fix

SITC of LED 'ELF' PAR, RGBW: 180w Pro-series using 60x 3w-1 LEDs: Powercon connectors for IN & OUT; DMX-512 signal, 6/9 DMX Channels: Beam Angle 30 degrees Al. die-cast housing: s/w suitable clamp (Make: NSC-Model: LP-603

Supply, installation, testing & Commissioning of LED Fersnal light with Lamp: High quality 200W LED Fresnel light used as a Key light, Back light, Fill light with dimming, spot & flood focus versions for creating various effects for multiple applications with specifications as below. Lamp power-180W COB LED Power supply-100-240 AC, 50/60 Hz Power cable 3 core 1 sq. mm. copper PVC insulated Color Temperature: 3200K Control: DMX512 / Manual Spot Flood focus adjustment. Complete in all respect as desierd by the Engineer in charge of work at site. Approved Makes martin/New stage craft/Showtec

Supply, Installation, Testing & Commissioning of LED profile 300w 36° voltage0-90-250v/50-60hz, working position: Any safe working position lamp: super high power LEDs; white 180w (cool white or warm white) average life time is over 5000h, CRI:>90, Lens angle: 19*/26/36",optinal, LED display channel-2 ch, IP rate :IP 20 indor, speacial zoom funcation with manual adjustment, control mode: master/slave synchronization, DMX 512 control and automatic, run, construction: die-casting aluminum housing silver white and black.optinal of Make: LPRO-300/Canara/ Robo/New stage craft

SITC of LED PAR with Lamp: 240W warm white LED, (50,000 hrs), Voltage: AC90-260V 50/60Hz, Power consumption: 200W, Dimmer: 0100% electronic dimming, High speed strobe effect with 4 default strobe modes and speed adjustable, Hight light output with pure and even coverage, Light angle 60° (8083A/B/C/D), 120°(8083K/L), Control: DMX512, master-slave and sound activated or auto operation, Channels 3/5/7(8083A), 5(8083D),3(8083B/C/L), 5/7/8(8083K) DMX channels USITT DMX-512, LED display, Low noise and efficient etc as required make: NSC Model : LPW-504

SITC of LED BAR LIGHT for CYCLORAMA: using/24nosx 12w Hi-Power 3-in-1 LEDs: IP-65 rated, Power AC 240V/50Hz 190W, Lamp Life: >50000 hours Beam Angle: 60"; 0-100% electronic linear Dimmer, 1-10 times/sec strobe; DMX-512 signal, 6 DMX Channels: Al die-cast housing; s/w Power & DMX data link cables, 4-leaf Barndoors & suitable clamp (Make: D.LED - Model: NSC-CFL-2412(RGBW)

SITC of LED FOLLOW SPOT Light (compact): Long throw, using Hi-Power 150w LED; On-board Manual Controls for Dimmer, Iris, Colors & CT Correction Filters: IP-20 rated; Power AC 240V/50Hz 165W: Lamp Life: >50000 hours; supplied with Folding Stand: Modal: 10R

STAGE AUDIO SYSTEM Supply, Installation, Testing Commissioning (SITC) of Main Speaker system, 2 way 15in + 1 CD Horn, having minimum SPL - 124dB/HxV dispersion - 90 x 40 ,450watts, imp- 8 ohms Make FBT/CSC/Renkus Heinz/OHM

SITC of 2x 18"driver in vent loaded enclosure having MAX -SPL- 135dB-AES Power -1400Watts IMP 4ohms Frequency response 30hz to 300hz. Make- FBT/CSC/Reinkus Heinz

SITC of 2 way high performance dual 6' driver in ABS enclosure having HxV Dipersion -100degreex80 degree . Frequency response 62-20 khz. MAX spl-122dB, Imp- 8 ohms Power handling 300 watts Make, EV /FBT/ CSC/ Reinkus Heinz

Supply, Installation, Testing Commissioning (SITC) of Stage Monitor Speaker system, 2 way 15in + 1 CD Horn, having minimum SPL - 122dB/HxV dispersion - 80 x 40 ,400watts, imp- 8 ohms Make FBT/CSC/Renkus Heinz/JBL

SITC of wall hanging speaker system with fixing clamp for Green Room .100 watts RMS Power, IMP- 8ohms, Make Yamaha/ CSC / FBT /EV

a) SITC of main speaker handling bracket made of >6mm thick iron ,- powder coated. to be hanged from cealing. Custom made.

b) SITC of balcony speaker Braket . Made of IRON , Powder coated . Custem made

SITC od four channel power amplifier with full protection RMS Power 1480 Watts/channel at 4 ohms. Make - Powersoft/ RAM Audio/ Lab Gruppen

SITC of 2 channel power amplifier with full protection RMS power 900 watts/ Channel at 4ohms. Make Powersoft/EV/RAM AUDIO

SITC of 24ch mixing console with at least 16 mic inputs , 100 MM fader, EQ with MID Sweep facility, Make - Yamaha / Sound craft/ Allen & heath

SITC of DIGITAL Speaker Management System having delay, crossover, pink noise generator with 6 out puts. Make - DBX/CSC/ Rane

SITC of 31 band Dual Channel graphic Equalizer having 12dB boost/ cut facility. Make - DOD/ DBX/EV

Microphone :-a) corded dynamic vocal microphone frequency response 50hz to 15khz. Make - SHURE/AKG/Audix

Microphone :- b) Corded Dynamic instrument Microphone 40 hz to 16 khz. Make: SHURE/AKG/Audix

Microphone :- c) Electret podium microphone with base. Make- SHURE/Audix/AKG

Microphone:- d) UHF H/H D/Diversity Wireless microphone . Make- SHURE/AKG

Microphone:- e) UHF Lapel D/ Diversity Wireless Microphone. Make - SHURE/AKG.

Microphone:-f) Over head Boundary condenser Microphone Make- SHURE/ AKG.

1) Micropone Stand - Large - AHUJA

2) Microphone Stand - Small - AHUJA

DVD Player of Standard make - SONY/ PH/ Samsung/LG

SITC of Speaker Cable of 4 Sqmm dia multistrand 99.9% copper through Conduit

SITC of Speaker cable laying of 2.5 Sqmm multisrand copper Through Conduit Pipe

SITC of Microphone cable laying of 2 core 14/36 swg through PVC conduit on stage

SITC of 50 mtr 20:4 Snake Cable through conduit (oxygen free copper)

SITC of M/S painted Stage Pocket Box with provision for 4 Nos XLR/ 4Nos Phono sockets

SITC of microphone cable of 10 mtr length with XLR in both ends.

SITC of Cables and Connectors (XLR/ Speakon / Phono jacks) for connecting Amplifier, speaker, mixer and other gadgets

SITC of suitable professional rack for mounting sound equipments with electrical Points, having doors & Locking Facility, Make-Alfatek or Similar

STAGE CRAFT MAIN CURTAIN Make- New stagecraft of velvet (INOVATIV/Relince) Main curtain made out of Velvet curtain cloth with Vertical sliding arrangement complete with fixing railing rack,fixing brackets.pully,drum, 2mm rope wire, 1HP Crompton/Godrej Motor, drum with groove cutting, pulleys,2 No air bracker switch(L&T, Siemens, GE make) for up & down,2 No air microswitch for auto stop,3 No push button for Open/Stop/Close position the curtain should be droped up down and curtain should be stitched in one dubale gathering Complete in all respect and to be approved by Architect and his representative. Appx. Size: - 23000mm * 6000mm

CYCLORAMA CUM SCREEN:- SITC Providing and fixing cyclorama screen in plastic perforated material. The screen to be fixed on tubular frame made out of 35mm dia MS pipe. Appx. Size:-10000mm x5000mm (per sq mm)

SIDE WINGS-STIC Providing and fixing cloth wings made out of black glazed cotton cloth) with fixed on both side of MS 50mm x 25mm x 16G pipe wielded frame work. The pipe framework made out of 25mm * 50 mm pipe. c/c 600 * 900 fixed with overhead pivote track complete with duly painted on both framework. Size : 1200mm * 5000mm Customized

FRILLS Providing and fixing average frills made out of double gathering glazed cotton to be installed above the stage on 28mm diams pipe Size: 20000MM (AV) * 1800MM

Stage suspension Grid: Providing & fixing MS suspension grid system over stage for hanging stage services made of 2 nos 40x40x5mm MS angles welded back to back with 50x 5 mm thk studs as MS spacers sandwiched between the MS angles so as to maintain 12mm gap between MS angles, the welded angles to be placed @ 1200mm c/c in one direction and 40x5mm thick MS Tee @ 600mm c/c in other direction. The MS grid to be suspended from the roof structure by means of MS flat suspender of 50x6mm thick MS flats @ 1200mm c/c in both directions. All MS members to be painted with a coat of red oxide primer & 2 or more coats of black enamel paint. All complete as per Architect or Architect's representative.

SERVICE: Installation, Testing, Configuration, Commissioning & Professional Engineering Charges

SCREEN WITH PROJECTION SYSTEM Projection System SITC of Digital Cinema Projector (Make - Christle, Model no-CP2210, 10000 lumnes

Supply with fitting, fixing &Commissioning of the Harkness perlux 180,1.8Gain Screen Std perf with web and eye of M Stube frame for the screen along with up-down mechanism as specified and directed by the department

LAJIK BRAHMA (BID ID -275937)