REPAIRS/REPLACEMENT TO SECURITY FENCING HARDSTANDING PATH DRAIN AND OTHER CONNECTED WORKS IN TECHNICAL AREA ZONE -1 AND II UNDER GE I RND RCI HYDERABAD

Amount

Demolition of brickwork or stone masonry including all quoins, arches, pillars, etc., built in cement mortar complete all as directed.

Demolition of brickwork or stone/boulder masonry laid dry in any position complete all as directed.

Taking down cement plaster of any description on brick or stone walls from any height including racking out joints, hacking for key, scrubbing down with water etc., including removal of rubbish material off the premises complete all as directed.

Demolition of PCC in ground floors and paving's not exceeding 15cm thickness (below or above ground level) complete including disposal of debris off the premises all as directed by Engineer in Charge.

M&L, walling of squared rubble masonry, regular coursed secunderabad type, well bonded, bedded and solidly hearted built in cement mortar 1:6, struck flush in the same mortar as work proceeds complete all as specified and as directed.

All as per item No 5 above but except stone. Note: Serviceable stones obtained from item No 1 shall be reused under this item.

M&L, brickwork with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L, brickwork with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L, 15mm thick rendering in cement mortar 1:4, on stone masonry surfaces or surfaces other than fair face of brick work, finished even and smooth without using extra cement complete all as specified and directed.

M&L, 15mm thick rendering in cement mortar 1:4, on fair faces of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L, boulder pitching hand packed tightly and grouted with cement and sand mortar 1:6 complete all as specified and directed.

All as per item No 11 above but except boulders. Note: Serviceable boulders obtained from item No 2 shall be reused under this item.

Dismantling fencing wire mesh of any description and any type complete all as directed.

Dismantling posts or struts (wood, steel or RCC) any section embedded in concrete masonry, including taking out embedded portion and making good disturbed ground complete all as directed

Excavation in post holes (or similar holes) each not exceeding 0.5Cum, getting out, in any type of soil including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

M&L, PCC 1:3:6, type C-1 using 20mm graded stone aggregate as in drain, surface channels and benching including necessary formwork complete all as specified and directed.

Extra for forming fair finished drain or channel of 30cm inner girth in cement concrete, using extra cement including forms moulds mitred / stopped ends etc., complete all as specified and as directed.

Add or deduct for serial item No.17 above for each 25mm inner girth or part thereof over or under 30cm.

Raking out joints and flush pointing to old squared rubbled stone masonry, coursed or uncoursed in CM 1:4 and removing rubbish off the premises complete all as specified and directed

M&L, Flush pointing to new squared rubble stone masonry, coursed or uncoursed built in CM 1:4 complete all as specified and directed

M&L, PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in foundations for fencing posts, plinth beams etc., and mass concrete complete all as specified and directed.

S&F, mild steel framed work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., including all necessary drilling, bolting or riveting etc., and similar works conforming to Fe 290 Gde-E-165 complete all as specified.

S&F, mild steel framed work such as grills, gratings etc., with ends of bars shouldered and /or riveted, or forged into spikes, framed guard bars; railings and similar works conforming to Fe 290 Gde-E-165 complete all as specified and as directed.

S&F in repairs, 1.60mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc., complete all as required and directed.

S&F, mild steel galvanized chain link fencing of approved mesh size and nominal dia GI wire with tolerance as per IS to any type of standards, rails, straining bolts, etc., including provision of line wires, binding wire complete all as specified and as directed. Note: The chain link fence fabric shall have zinc coating of type heavy as given in IS 4826 or in IS 12753. Tolerances permitted on the diameter of mesh and line wire shall be as given in IS: 280.

S&F in repairs, Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixed to any type of standard rails straining bolts including securing or tying at crossings with galvanized mild steel wire, staples or steel pins etc., complete all as specified and directed. Note: Each line wire shall be measured.

S&F, Mild steel screw bolts (machine made) 5 to 10mm diameter of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 5CM but not exceeding 10CM long complete all as specified and directed.

M&L, 60mm thick, M-35 Grade, machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 complete all as specified and directed

M&L, 50mm sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L, 25mm thick chequered cement concrete tiles of 300mm x 300mm size with grey cement and pigments, set, jointed and pointed in neat cement slurry over and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L, PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L, 100mm thick PCC 1:2:4 type B-1 in flooring using 20mm graded stone aggregate finishing the surface even and smooth without using extra cement including necessary formwork complete all as specified and directed.

M&L, 75mm thick PCC 1:4:8 type D-1 in sub base using 20mm graded stone aggregate finishing the surface even and rough including necessary formwork complete all as specified and directed

M&L, PCC 1:2:4, type B-0 using 12.5mm graded stone aggregate as in coping and the like including necessary formwork, weathering, slightly rounded or chamfered angles and throating and other similar works complete all as specified and directed.

M&L, forming Contraction (Dummy) joints 65mm deep x 100mm wide and filled with sealing compound grade 'A' complete all as specified and directed.

Dismantling of wrought iron or mild steel works of any description not otherwise provided for complete all as directed.

Demolition and breaking up drain pipes of any size (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as directed.

M&L, 300mm bore reinforced concrete pipes, class NP2 with collars laid to falls in trenches or concrete bed, jointed in cement mortar 1:1 including packing under and haunching against the sides of pipes using PCC 1:3:6 type C1 using 20mm graded stone aggregate as in concrete bed, testing complete all as specified and as directed

M&L, 450mm bore reinforced concrete pipes, class NP2 with collars laid to falls in trenches or concrete bed, jointed with cement mortar 1:1 including packing under and haunching against the sides of pipes using PCC 1:3:6 type C1 using 20mm graded stone aggregate as in concrete bed, testing complete all as specified and as directed

M&L, preparation of old concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint as per approved pattern complete all as specified and directed.

M&L, preparation of new steel surfaces of any description, over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L, pre cast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slabs including necessary form work, placed in position, set in cement mortar 1:4 complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

S&F, mild steel round bars 8mm dia, for secuirng chain link fencing including two coats of painting with synthetic enamel paint over a coapt of primer complete all as specified and as directed.

M&L, TMT bars 8mm dia, as in reinforcement cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Dismantling Asbestos cement or mild steel (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as directed.

S&F, Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet / trapezoidal steel sheet 0.50mm base metal thickness of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws and EPDM washers complete all as specified and directed.

M&L, preparation of old decorated surfaces of walls including cornices etc., and applying one coat of white wash complete all as specified and directed.

M&L, preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and as directed.

M&L, preparation of concrete/terrace floor tiles, cement tiles applied to walkways or driveways, paver blocks or any plain cement surface by scrubbing with wire brush to remove loose dirt, algae and fungus growth, washing with water and applying two coats of anti algal/fungal floor coat emulsion paint as per manufacturer's instructions complete all as specified and as directed.

S&F in repairs, Cats eye road stud, ABC body conforming to IRC specifications, 100 x 100 x 18.5mm size, dynamically designed having high compressive strength as per MORT&H, dual directional reflection and fixing with epoxy on road surface complete all as specified and as directed. Make: 3M / Dark eye / Sing tech / Greenlite

Cleaning the bituminous road surfaces by removing all dirt, scales of oil, grease and foreign material etc., and applying 2.5mm thick hot thermoplastic road marking paint by fully automatic thermoplastic paint applicator machine for marking of centre line, lane divider line and zebra crossing line etc., machine shall be fitted with profile shoe, glass beads dispenser, propane tank heaters and profile shoe heater and driven by experienced operator on road surface complete all as specified and directed. Note: Quoted rate shall deemed to include cost of all material, labour, machinery etc., required for proper completion of work. Properties of thermoplastic materials shall conform to section 803.4.2 of Ministry of Road Transport and Highways.

S&F in repairs, retro reflective informatory sign board of size 800 x 600mm made of 14gauge (2.0mm) thick aluminium sheet having one coat of zinc chromate stoving primer and two coats of stoving enamel on back side only and front face fully covered with white encapsulated lens retro reflective sheeting of high intensity grade as per manufacturer's instructions complete all as specified and as directed. Note: The sheet shall be affixed to the base by HLVA process. The size of border and sign shall be as per IRC 67/1977. The board shall have back support frame of mild steel angle of size 35 x 35 x 6mm and shall have fixing arrangement to the post.

M/S K.SANJEEVA REDDY

saradhi construction combines

M/s ANUSHA ENTERPRISES