Repair and maint of STPs, High mast, parking and Garden lights under GE Gurdaspur.

Amount

S&F in replacement to STP main control panel by disconnecting all electric connections and dismentling the annuciator, alongwith all connected parts and reassembling after necesssary repair, replacement of lugs,dressing of cable, replacement of connectror blocks, nuts bolts and washers of suitable size and joints complete all as specified and directed.

S&F in replacement and disconnecting of all electrical connections of non clog submersible pump rating 9.5 KW & discharge of 60 cum/hr, taking out from sewge well dismantling of pump, shaft impeller unit etc and shifting it to work shop for reparing, reassembling and back after repair to the site by transport and lowering to sewage well after testing and commissioning complete all as specified and directed by Engineer-in- Charge. (Note :- Spare parts and rewinding shall be measured and paid for separately).

M&L for dismentaling/opening the burnt motor, (rotor & stator) rewinding the motor with super enamelled copper winding as per existing gauge including insulation material cotton tape, varnish, insulation paper, sleeves and dry and backing etc including replacing of bearing and reassembling complete motor complete all as directed.

Supply and replacement of SS impeller for 9.5 KW & discharge of 60 cum/hr non clog submersible pump as per existing make and capacity complete all as speicifed and directed.

M&L for repair pump shaft by filling of suitable material by welding and turning of pump shaft of capacity 9.5 KW & discharge of 60 cum/hr non clog submersible pump complete all as specified and directed.

S&F in replacement of mechanial oil seal for 9.5 KW & discharge of 60 cum/hr submersible pump as per existing make and capacity complete all as specified and directed.

S&F in replacement of framed work such as grills gratings, etc. with ends of bars shoulders and / or riveted, or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters, railings and similar article as in strainer fabrication for MBBR including welding work etc complete all as specified and directed.

S&F in replacement of MCB 32 Amp, 4 pole with rupturing capacity10 KA C curve all as specified and directed.

S&F in replacement of MCCB 160 Amps 4 Pole 25KA complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of MCCB 63 Amps 4 Pole 25KA complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of MCCB 32 Amps 4 Pole 25KA complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of fan belt SPB-PT 1800 suitable for air blower complete all as specified and directed.

S&F in replacement of fan belt SPZ-1600 suitable for sludge transfer pump complete all as specified and directed.

S&F in replacement of fan belt SPZ-1320 suitable for sludge feed pump complete all as specified and directed.

S&F in replacement of 3 pole power contactor MNX 25 heavy duty with contineous current rating of 25 Amp AC 3, 415 Volt complete all as specified and directed.

S&F in replacement of 3 pole power contactor MNX 32 heavy duty with contineous current rating of 32 Amp AC 3, 415 Volt complete all as specified and directed.

S&F in replacement of thermal over load relay 10 to 16 Amp /415 Volt complete all as specified and directed.

S&F in replacement of electronic timer for star delta starter 415 volt timing range 3 sec to 60 sec. complete all as specified and directed.

S&F in replacement voltmeter digital LED type, 0-500V complete all as specified and directed.

S&F in replacement 3 phase digital LED type ammeter, 0-100 Amp complete all as specified and directed.

S&F in replacement indicator lamp RYB LED type complete all as specified and directed.

S&F in replacement push button ON (Green) / OFF (Red) set complate all as specified and directed.

M&L for rewinding of electric induction motor 60 HP (motor of air blower ) including disconnecting electrical connection and shifting to workshop, opening the electric motor rotar & stater. Rewinding the motor as per existing gauge of copper winding wire, varnish, insulation sleve and reassembling the motor shift at site and connecting, testing on load complete all as specified and directed.

All as per Srl item No 24 here-in-before but capacity of 10 to 15 HP (Motor of anoxic recirculation pump).

All as per Srl item No 24 here-in-before but capacity upto 10 HP (Motor of sludge transfer pump , sludge feed pump, centrifuge, dozing pump).

M&L for repair to air compressor of capacity of 45 KW & discharge of 1840 cum/hr of deffusers coarse bubble/ nozzles including opening carefully and cleaning/ repair/ replacement rotary turn lobe air blower with air filter, silencer, gauge, safety valves, drive bearing and bearing (gear side) oil seal drive end long shaft and short shaft, lip seals gear and bearing cover, gasket gear cover and welding grinding & polishing drive rotor shaft assembly as per bearing size. Replacement of oil grade, greasing, assembling and testing on load complete all as specified and directed. (Note :- Cost of air filter shall be deemed to be included in item rate quoted by Contractor).

S&F in replacement of CI butterfly valve heavy grade with stainless steel stem & disc size150 mm dia complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 28 here-in-before but size 100 mm dia.

All as per Srl item No 28 here-in-before but size 80 mm dia.

All as per Srl item No 28 here-in-before but size 50 mm dia.

S&F in replacement cast iron non returning valve (reflux with by pass) with flanged both ends of size 150 mm dia bore all as specified and directed.

S&F in replacement of cast iron non return butterfly valve 200 mm dia complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 33 here-in-before but size 150 mm dia.

S&F in replacement CI sluice valve class PN- 1.6 ISI marked with stainless steel spindle and gun metal working part, flanged both ends of size 80 mm dia bore with hand wheel complete all as specified and directed.

S&F in replacement of gun metal/globe or gate valves of 20mm dia with iron wheel head, ISI marked confirming to IS-780, screwed both ends for iron pipe all as specified and directed.

All as per Srl item No 36 here-in-before but size 25 mm dia.

S&F in replacement of submercible rubber PVC 2.5 Sqmm, 8 core copper cable , 1100 volts conforming IS 694:1990 complete all as specified and directed.

Supply and laying LT cable XLPE insulated armoured heavy duty electric with aluminium conductor cable 1100 volt grade 150 Sqmm 3.5 core including taking down existing all as specified and directed. (Note:- Excavation, earth work, sand cushioning, brick protection, GI pipe shall be measured and paid for separately).

Supply and laying LT cable XLPE insulated armoured heavy duty electric with aluminium conductor cable 1100 volt grade 50 Sqmm 3 core including taking down existing all as specified and directed. (Note:- Excavation, earth work, sand cushioning, brick protection, GI pipe shall be measured and paid for separately).

All as per Srl item No 40 here-in-before but size 16 sqmm 4 core.

All as per Srl item No 40 here-in-before but size 10 sqmm 3 core.

Supply and laying cable with aluminium conductor cable 1100 volt grade 2.5 Sqmm 3 core including taking down existing all as specified and directed.

S&F cable jointing kit 1100 V grade cable for out door termination heat shrinkable type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium cable of size 150 Sqmm all as specified and directed.

S&F cable jointing kit 1100 V grade cable for straight through heat shrinkable type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium cable of size 150 Sqmm all as specified and directed.

M&L for cleaning of equalisation sewage tank (dia 11.5 mt, height 3 mt ) for 2.5 MLD STP by cleaning with brush entire internal surface by removing dirt , sludge etc and disposal not exceeding 50 mtr and applying bleaching powder, fresh water and clean entire surface repeatedly with fresh water and draining out soiled water including using sludge cutter pump and suction pump of suitable capacity surface complete all as specified and directed, using acid and other suitable methods, taking out air piping, descaling , clear holes and refixing the same all as specified and directed by Engineer-in-Charge. (Note: - Quoted rates shall be deemed to be included ladder for man entring in to tank for removing of sludge from tank de-watering etc).

M&L for taking out MBBR media from tank & cleaning of MBBR tank (dia 7.8 mt & height 6.2 mt) for 2.5 MLD STP by cleaning with brush entire internal surface by removing dirt , sludge etc and applying bleaching powder and fresh water. The cleaning of tank includes following :- (a) Taking out MS/HDPE pipe with strainer , descaling the pipe and taking out the strainer , cleaning of strainer/ repair by suitable welding or replacement of stainless steel bars as required at site. (b) Descaling of air grid and cleaning of holes for air piping. (c) Applying red oxide on all piping inside MBBR tanks and inner surface of tanks followed by two coats of epoxy paint.

M&L for cleaning of tube settler with intermidiate tank (length 12.7 mt, width 6.5 mt) for 2.5 MLD STP by cleaning with brush entire internal surface by removing dirt , sludge etc and applying bleaching powder, fresh water and cleaning entire surface repeatedly with fresh water, draining out soiled water, cleaning of chennals and applying chemical inside tube settlet tank and inner surface walls of tanks with two coats of epoxy paint over a coat of red oxide primer. (Note - Quoted rates shall include ladder for man entring in to tank for removing of sludge from tank and de watering etc).

All as per Srl item No 48 here-in-before but hypo solution tank with chlorine tank for 2.5 MLD.

M&L for cleaning of grit chamber, bar screen & stilling tank as described below :- (i) Dewatering with submercible / sludge pump to empty the sump/tank upto base level. (ii) Removing sludge from sump wall and bottom with the help of special sludge pump and remaining dirt which may have hidden in rough slots of the bottom mannualy with brushes. (iii) Applying bleaching powder for disinsfection of sump. (Note: - Cleaning of grit chamber, bar screen, stiling chamber will be considered as one job for payment).

All as per Srl item No 50 here-in-before but of treated water tank at STP 1 & STP 2.

All as per Srl item No 50 here-in-before but of clear water tank at 8 different locations.

S&F in repalcement of single phase preventor complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of MCB single pole rating 6 Amp 10KA complete all as specified and directed.

M&L for painting of pipes of size upto 150 mm dia with two coats of synthetic paint over one coat of red oxide primer including connected fittings, nut, bolts etc complete all as specified and directed by Engr-in-Charge.

Painting of following installed machineries at 2.5 MLD STP scrapping existing paint and spraying two coat of synthetic enamel paint over one coat of primer as per colour coding all as directed. (a) Sand filter & activated carbon filter (b) Anoxic recirculation pump 1 No (c) Air blower 2 nos (d) DWPE Dosing pumps 2 nos (e) Sludge transfer pumps 2 nos (f) Sludge feed pumps 2 nos (g) Centrifugal pump 1 no (Note:- Painting of connected pipes will be measured separately under item no 55).

Supply only fresh cow dung for maintaining MBBR complete all as specified and directed.

Supply only urea for maintaining MBBR complete all as specified and directed.

Supply only DAP for maintaining MBBR complete all as specified and directed.

Supply only Jaggery for maintaining MBBR complete all as specified and directed.

Rectification of electric complaint of sewage installation/ water supply replacing the brunt lugs of cables to check auto star delta starter , voltmeter , ammperemeter in pump panel change over switch and making functional if minor repair involves to abvoe equipments complete all specified and directed.

Removal of dry sewage from dry bed and deposting outside the cantt area complete all as specified and directed by Engr-in-Charge.

S&F in replacement of terminal block 4/6way as required and directed, barrier type, panel mountable with current carrying capacity of upto 25A, suitable for voltage of 415 volts, complete with screws and other accessories complete all as specified and directed.

Supply and spraying glyphosate 41% SL Glykol Herbicide to remove vegatation from STP Installation area complete all as specified and directed by Engr-in-Charge

S&F in replacement of 4 Sqmm, 3 core PVC insulated & sheathed copper flexible cable complete all as specified.

Repair / replacement of control wiring of control panel with new PVC insulated, unsheathed, copper stranded conductor wire 1.5sqmm including testing all as direced by Engineer-in-Charge.

S&F in replacement new generation energy saving IP66 street light luminiaries withlong life versatle pressure die-cast aluminium road way luminaire with high power LED 45 watt including replacement of the GI pipe bracket with clamps and nuts, bolts all as directed by Engineer-in-Charge.

Supply only floating type media for MBBR as per sample for STP black as per sample complete all as specified and directed.

S&F in replacement CI pipe of 150 mm ISI marked with flanged ends socket ends with push on rubber gasket joint etc all as directed.

S&F ductile iron centrifugally cast (spun) pressure pipe class K-9 size 100 mm ISI marked with internal cement mortar lining and external zinc and bitumen coated pipe 100mm bore with all spigot and socket ends with push on rubber gasket joint etc all as specified and directed

All as per Srl item No 70 here-in-before but size 150 mm bore.

S&F in replacement GI tubing , medium grade, galvanised, with all fittings, laid in trenches of size 80 mm bore complete all as specified and directed.

All as per Srl item No 72 here-in-before but size 50 mm bore.

All as per Srl item No 72 here-in-before but size 25 mm bore.

All as per Srl item No 72 here-in-before in before but size 20 mm bore.

S&F in replacement PVC pipe with all fittings of size 15 mm bore complete all as specified and directed.

S&F in replacement UPVC pipe SCH 80 with all fittings laid in vertical position in MBBR of size 250 mm bore complete all as specified and directed. (Note :- Pipes will be used in MBBR in vertical position).

S&F in replacement UPVC pipe SCH 80 with all fittings, of size 160 mm bore complete all as specified and directed.

S&F in replacement 500 litres capacity, rotational moulded polythelene water storage tanks white (cylindrical vertical with closed top), hoisted and fixed in postion complete all as specified and as directed.

Collection of treated water sample from STP l & ll and analysis quarterly and when directed and getting the sample tested from a govt approved laboratory and submission of report to Engr-in charge. Parameters such as pH, TSS (mg/l), TDS (mg/l), EC us/cm, COD (mg/l), BOD (mg/l), Chloride (mg/l), Sulphate (mg/l), Oil & Grease (mg/l), T. Coil MPN/100 ml, F. Coil MPN/100 ml, SAR (mg/l), Amn nitrogen (mg/l) TKN (mg/l), T. Phosphorus (mg/l), RSC (mg/l) and oil and greasing or any other test shall be maintain as per CPCB Norms.

M&L for preparation of old painted surfaces of one MBBR tank and apply two coat of exterior acrylic emulsion paint, complete including painting with two coats of synthetic enamel first quality paint including making black ground surface for marking/ writing of date of cleaning, due date of cleaning, capacity of tank in front side of colour and at height as directed by Engineer-in-Charge. (Note :- (a) Arrangement of scafoalings, safety belts, helments and other safety gears while painting are responsibility of contractor. The contractor shall take the insurance of his workforce who are working on heights. The cost of these securily/ safety measures are deemed to be included in the quoted rates).

All as per Srl item No 81 here-in-before but tube settler tank with intermidiate tank.

All as per Srl item No 81 here-in-before but hypo solution tank.

All as per Srl item No 81 here-in-before but grit chamber, bar screen & stilling tank. (Note:- Painting of grit chamber, bar screen, stiling chamber will be considered as one job for payment).

All as per Srl item No 81 here-in-before but clear water tank, pumps and connected down pipes.

Dismentling old unserviceable valve pits and constructing of brick masonary pits of internal dimensions 1mx1mx1.2m (bottom PCC floor of the pit shall be 30 cms below the bottom surface of sluice valve flange to provide sufficient working space) , brick work shall be in CM 1:4, floor of the pit shall be in PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) 10 cm thick inner and exposed surfaces and bottom floor of the pit shall be plastered in CM (1:4), 15mm thick. The sluice valve and other fittings shall be housed in centre of the pit. The vertices of the pit shall in right angle and champhered .The top cover of the pit will be made out of MS sheet made of 2mm thick with angle iron frame made out of MS angle 50mm x50 mmx 6mm with galvanised steel hinges two Nos and locking arrangements duly painted with two coats of synthetic enamelled paint over one coat of red oxide all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with GI earth plate electrode 600mm x 600mmx6mm thick burried in ground vertically to a depth not less than 2.25meters below ground level with top edge of the earth plate at a depth not less than 1.5 meter below the ground level, earth plate surrounded with 15cm thick layers of common salt and charcoal dust starting from ground below 15 cm of earth plate and up to 15 cm above the same, GI plate connected with galvanised steel strip of size 25x4 mm by means of GI nuts, bolts and washers, Strip laid in 50mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode shall be included in the rates quoted by the contractor) with following:- (a) Test point GI strip of size 25x4. (b) Watering pipe GI Medium grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm constructed in PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC pit cover 40mm thick with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover. (d) Angle iron frame made of 40x40x4 mm angle iron for 30x30 mm PCC pit for holding the pit cover. (Note :- The cost of excavation, earth work, watering pipe, gun metal test point, MS funnel with brass wire mesh and RCC pit with pit cover shall be deemed included in the rates. No extra cost shall be paid to the contractor against these items).

S&F in replacement of float switch N1, 10 mtr for sewage pump including electric connection complete all as specified and directed.

S&F in replacement of unserviceable flow meter electromagnetic type, average flow 2 mld complete all as specified and directed.

Supply only potassium dichromate for COD testing complete all as specified.

Supply only mercuric sulphate for COD testing complete all as specified.

Supply only farrous sulphate for COD testing complete all as specified.

Supply only sulphuric acid complete all as specified.

Supply only ammonium ferrous sulphate complete all as specified.

Supply only ferroin indicator solution 100 ml fisher complete all as specified.

Supply only ferric chloride 500 gm avrice complete all as specified.

Supply only sodium iodide 100 gm qualikem complete all as specified.

Supply only di-sodium hydrogen orthophosphate 500 gm complete all as specified.

Surface dressing n. exc 15 cm deep of soft/loose soil site clearance ground STP installations area complete all as specified and directed by Engr-in-charge. (Note :- leveling of the disturbed surface will be done by tractor or other equivalent means by the contractor).

Excavation in trenches in soft loose soil including cutting road surfaces n.exc 1.5 mtr wide and n.exc. 1.5 mtr in depth for poles, stay, cable, pipe etc getting out all as specified.

Removal of excavated soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Returning, filling in, including spreading, leveling,watering and well ramming in layers each n.exc 25 cm thick in soft loose soil all as specified.

Supply and laying brick common burnt sub class "B" old size (compressive strength not less than 75 kg per sqcm) for protection of cable laid in trenches for under ground cable all as specified.

M&L for sand cushioning trenches using fine sand to under ground cable, laid in two layers 15cm before laying the cable & 8cm after laying the cable complete all as specified and directed.

Supply only liquid chlorine for dozing purpose complete all as specified

Supply only potassium iodide complete all as specified

Supply only salicicylic acid complete all as specified

S&F in replacement of bubble diffuser of bubble diameter 3mm for air flow in sewage sump, MBBRs and all tanks of STP complete all as specified and directed.

M&L in replacement for gear oil fully synthetic EP 90, API GL-4/ GL-5 or above for gear lubrication complete all as specified and directed by Engineer-in-Charge.

M&L for dismantling/taking down carefully by disconnecting of electric connection from pole/ walls of any height and any situation/loction,place Street light fittings type of tube rod 36/40 watts, HPSV, HPMV, LED street lights any wattage of flood lights,post top lanterns etc. complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of LED post top lantern with powder coated aluminum body with clear/ opal diffuser in IP-66 fitting of 40 watt suitable for landscape lighting complete all as specified and directed.

S&F LED flood light 200 watt 230V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp in replacement metal halide flood light hoarding light luminaire complete with all accessories, connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed by Engr-in-Charge.

All as per Srl item No 112 above but LED flood light 120 watt all as directed by Engineer-in-Charge.

All as per Srl item No 112 above but LED flood light 50 watt all as directed by Engineer-in-Charge.

S&F LED street light 90 Watt WARM WHITE 3000K with sensor dusk and dawn, PF>.95 silicon gasket for IP 66 (no glue) protection suitable upto 50mm OD pipe mounting holder fixed on existing poles. LED street light shall be made up of pressure die cast alluminium alloy complete with toughened glass , having driver integral (inbuilt 4 KV SPD), external 10KV SPD, driver effeciency >90%, system efficacy >100 lumens/ watt, operating voltage 140V - 270V 50 Hz, THD <10% surge protection 10 KV, CRI >70, aluminium LM6 alloy housing with toughened glass and high power LEDs and secondary lenses with IP 66 protections top opening for separate driver compartment with frame, brand, logo embossed, toughened glass cover. High power ceramic base, CRI > 70 and bolted inside the luminaire panel. Average life class of 50000 hrs metal body fully coated phase to phase protection at 440 V upto 4 hours and > 300 V auto cut and restart feature. Luminaries and driver shall be of same make all as specified and directed.

Supply and fixing energy saving LED INVERTER TYPE STREET LIGHT 45 WATT AND BATTERY BACK UP OF MINIMUM 2 HOURS environmental friendly, long life , exclusive innovative die-cast aluminium IP 66 security light with high power LEDs as light source, suitable for 40 mm GI pipe , 5700K LED and connecting up with twin core twisted flexible copper conductor cable all as directed.

S&F high intensity , energy saving long range multi functional auto switch LED search light of beam range not less than 500 meters, 1x200 watt LED lights,narrow beam 8 degree , die cast LM6 housing with heat sink round body with air fins , powder coated with average lux level at 10 meter - 4000 lumen (approx) with circle of approx 1 meter IP 66 conforming to LM 79 & 80 report . The search light will be installed on the disc of the revolving mechanism with suitable motor gear unit and designed of rotate 360 degree continously in horizontal plane with speed controlled to 1-10 Amp radio frequency button with in built push to titling option upto 45 degree including a wall mounted wired contronl panel with earthing terminal and PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) complete all as specified and directed.

Repair / tightening of end terminals of street light fitting, flood light, post top lantern of any size/capacity at any height and repair the street lights, flood lights and post top lanten having minor faults i.e loose connections, carbon deposition, shifting and refixing the same etc and making the light functional all as specified and directed by Engineer in charge. (Note : (a) Complaint shall be done within 24 hrs after intimation by JE E&M Engineer-in-Charge failling which penalty of Rs 250 per day per complaint will be levied on contractor. (b) One supervisor will report to JE E/M , Engineer -in-Charge on daily basis with complaint register).

S&F in replacement of 3 pole power contactor of amp rating 25 Amp 3AC and 45 Amps 1 AC as per existing make and rating all as directed by Engineer in charge.

Supply and laying weather proof flat twin core cable aluminium conductor 1100 volts grade size 10 Sqmm including taking out old one all as specified and directed.

S&F LT straight through cable joining kit heat shrinkabale complete with jointing materials suitable for LT armoured cable 3.5/4 core of size 70 Sqmm to 120 Sqmm complete all as specified and directed.

S&F in replacement of PVC cable aluminium conductor of size 2.5 sqmm 2 core all as specified and directed by Engineer-in-Charge.

S&F in replacement of junction box poly corbonate size 200x140x95mm with glass fibre reinforced, environment friendly, recylable, UV resistant, halogen and silicon free anti acid and anti corrosive IP 66/67 in accordance with IE rule internally embedded gasket, junction box including 3 phase 415 volt aluminium bus bar and Din rail for fixing the MCB including one No. MCB SP 6A 10KA to control the street light including necessary clamps, nuts bolts to fix the junction box with poles all specified and directed.

M&L for preparation of old painted surfaces of electric pole removing complete dust and other deposited materials by cleaning from steel tubular pole of length upto 9 to 12 metres cross arms, bracing, clamps etc and painting with one coat of aluminium paint, retaining and repainting existing marking on pole and replacement of reflective band of 3M brand RED-YELLOW-RED alternate coloured 3 numbers of minimum 5 cm in height wrapped all around the pole all as specified and directed by Engineer in Charge.

Supply and laying, connecting, in replacement XLPE insulated armoured (under ground) heavy duty electic cable with stranded aluminium conductor 1100 volts grade cross sectional area 16 Sqmm 4 core laid in trenches/ducts/ through pipes/in floor road/along the pole including finding out the fault in cable complete all as specified & directed by Engr-in-charge. (Note :- Excavation earth work, road cutting, brick for cable protection and sand cushioning shall be measured and paid for separately. Only manually excavation will be done at site to avoid damage to cable protection brick and LT Cable).

All as per Srl item No 125 here-in-before but 25 Sqmm 4 Core.

S&F in repair of motor and other accessories for rotating of light all as specified and directed by Engineer-in-Charge.

S&F in repair of motor for hosting and loweing of light from high mast pole to carry out repair all as specified and directed.

M&L in replacement for cable protection GI tubing light grade fixed along with pole/wall/ under road of size 40mm bore with nuts, bolts and clamps including taking down existing complete all as specified and directed.

M&L in replacement of unserviceable driver for LED flood light capacity 120 watt for any make all as specified and directed by Engineer-in-Charge.

All as per Srl item No 130 here-in-before but capacity 200 watt.

M&L in replacement of PC for LED flood light capacity 120 watt for any make complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 132 here-in-before but capacity 200 watt.

S&F piercing connector for service connection suitable for 35sqmm AB cable complete all as specified and directed by Engineer-in-Charge.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit Rs. 2,04,565/- from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

P S BUILDERS (BID ID -3371971)

SUN CHEMICALS (BID ID -3372741)

INDERJIT SINGH (BID ID -3372267)

BUILDEX CONSTRUCTION CO (BID ID -3371806)

Ashoka Engineers (BID ID -3372291)

M/S TARSEM CHAND AND SONS (BID ID -3372244)

SB TRADING CO (BID ID -3372314)

M/S SUDERSHAN KUMAR CHOPRA GOVT CONTRACTORS (BID ID -3372740)