SPL REPAIR TO TOILET BLOCKS OF CHILDREN SCHOOL, OFFR MD ACCN P-395/1 AND 3 AND PROVN OF CERTAIN SANCTIONED WORKS UNDER AGE B/R-II AT ITARANA, ALWAR

Amount

Demolition cement concrete (unreinfored) as in ground floor and paving not exceeding 15cm thick below or above the ground level complete all as specified and directed.

Taking down cement plaster of any type of surface finshes (including tiles) racking out joints hacking for key scrubbing down with water in any description in any position complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quion arches complete all as specified and directed.

M&L brick work with fly ash 'brick (old size brick) straight or curved on plan exc 6m mean radius built cement mortar 1:6 complete all as specified and as directed.

M&L brick work with fly ash 'brick in any radius built cement mortar 1:4, half brick thick wall complete all as specified and as directed including 2 Nos 8mm dia round bar every four couse of brick masonary.

M&L 15mm thick rendering in cement mortar 1:6 on other than fair faces of brick work surace finished even and smooth with out using extra cenent complete all as specified and directed.

M&L 5mm thick rendering in cement mortar 1:3 on ceiling surace rendering is to be even and smooth with out using extra cenent complete all as specified and directed.

M&L rough cast plaster on exterior walls applying the under coat of cement and sand morrtar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed.

M&L preparation of newly plasterd surface of wall and applying two coats of oil bound distemper over and including a coat of wall putty 2mm thick complete all as specified and directed.

M&L preparation of newly plasterd surface of ceiling surface and applying three coats of white wash complete all as specified and directed.

M&L preparation of newly plasterd surface of wall and applying two coats cement base paint over a coat of primer complete all as specified and directed.

M&L PCC 25mm thick 1:2:4 type B0 (using 12.5mm graded aggregate) as in floor as in levelling levelling course complete all as specified and directed.

M&L PCC 1:4:8 type D2 (using 40mm graded aggregate) as in foundation filling and mass concrete as floor sub base complete all as specified and directed.

Demolition of cement concrete (reinforced) in landing slab, chullah hoods, manhole covers, roofs, floors, beams, stair case, landing, chajja and similar suspended work complete all as specified and directed.

M&L providing precast cement concrete 1:2:4 type B-1 as in landing, cover slabs (for manholes etc) chajjas, water troughs, managers, shelves and similar article with plain faces complete all as specified and directed.

M&L providing precast cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span,cills, steps, seismic and other similar bands, plinth courses, string courses , lacing courses, parapits and railings upto 60cm in height, copings kneelers, apex stones, bed plates, kerbs, water throughs and the like including weathering slightly rounded or chamfered angles and throating as directed.

M&L TMT bars 10mm dia and over cut to length to shape required including cranking, bending spirally or hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9 mm dia all as specified.

All as per item No 17.00 above but 6mm to 8mm dia TMT bars.

Taking down carefully existing bitumen tarfelt including plaster of any description over the surfaces of roof, terraces including flashing and junction of parapets/curve walls etc and removing of the rubbish and deposting where directed complete all as specified and directed.

M&L 20mm thick CM 1:4 on fair faces of concrete /brick surfaces with water proofing compound @ 3% by wt of cement finished even and smooth in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane finished complete all as specified including taking (Polymeric membrane and WPC shall be meausred and paid seperately here-in-after).

M&L water proofing treatement to RCC roof slab including parapet comprising of following course of treatement/specified from bottom to top (a) Applying bituminous primer @ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces. (b) Over the priming coat laying one layer APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.5 Kgs/Sqm and upper side of membrane thermally insulated with white mineral gravel finish , unifirmly embeded during manufacturing process shall only be used, it shall be laid by torch application. Side overlap should be 75mm and end shall be 100mm. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside parapet in groove. The same shall be finished by a membrane flashing.

M&L 75mm thick cement concrete 1:3:6 type C1 (using 40mm graded crushed stone aggregate) as in plinth protection path laid in panel surface finished even and fair including making the joints 10mm thick and filled with tank mastic bitumen using extra cement complete all as specified and directed.

M&L machine pressed precast concrete interlocking coloured paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade laid over and including 25mm thick sand cushion complete all as specified and directed.

M&L providing precast cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span,cills, steps, seismic and other similar bands, plinth courses, string courses , lacing courses, parapits and railings upto 60cm in height, copings kneelers, apex stones, bed plates, kerbs not provided and the like including weathering slightly rounded or chamfered angles and throating as directed.

M&L providing precast cement concrete (Type B0, 1:2:4 using 12.5mm graded aggregate) as in louvers and jalies 35mm thick (measured solid) including all mouldings but excluding frame(pre cast frame shall be measured and paid separately) fixed with cement mortar 1:4 complete all as specified and directed.

Treatement for sunken portion is as follows :- (a) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (b) Maintain the Sunken to a slope of 1:40 outward with 32mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall. (c) Top of the sunken floor slabs shall be laid to a slope 1:40. The surface of RCC slab shall be made even and smooth by using extra cement while the concrete is still green. Concave fillet in PCC (1:2:4) type B0 of radius 75 mm shall be provided at the junctions of RCC slab and adjoining walls. (d) Floor and side walls upto the finished floor level shall be plastered with 15 mm thick CM (1:4) mixed with water proofing compound @ 3% by weight of cement. Over plastered surfaces, a layer of APP based polymeric membrane not less than 3mm thick, weighing not less than 3 kg per sqm, reinforced with polyster non- woven fabric (weighing not less than 150 gm per square metre) shall be laid by torch application. Side overlaps shall be 100mm and the ends laps shall be 150 mm and overlap joints shall also be sealed by torch application. (e) The sunken portion shall be filled with lean cement concrete (1:5:10), type E2 using 40 mm brick aggregate after carrying out satisfactory testing of CI pipes / joints and slabs / walls by filling water for 72 hours. The sunken portion of Nahani / floor trap and pipe joints shall be embedded in PCC (1:3:6) blocks. (f) 32 mm dia GI spout shall be provided to drain out leakage, if any.

Supply only waterproofing compound.

Dismentling stone slab and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar including removing the dismantled materials complete all as specified and directed.

S&F granite (of any type) 16 to18mm thick jet black (table rubbed and polished) in steps, jambs, pillars ,window cills,cooking platforms and like (including cutting for fixing of WHB, Sink etc) in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L non skid joint free ceramic colour tiles 7 to 8mm thick area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 sqm set and jointed in neat cement slurry in floor and pointed in colour cement to match the sade of tiles including sceed bed or bedding layer of mortar 15 mm thik 1:6 complete all as specified and directed.

M&L non skid joint free ceramic colour tiles 7 to 8mm thick area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm set and jointed in neat cement slurry in floor and pointed in colour cement to match the sade including sceed bed or bedding layer of mortar 15 mm thik 1:6 complete all as specified and directed.

M&L glazed ceramic colour tiles 250mm x 350mm / 350mm x 450mm x 7 to 8mm thick set and jointed in neat cement slurry and pointed in coloured cement on vertical surfaces such as skirting/dado over cement mortar rendering 10mm thick 1:4 complete all as specified and directed.

Taking down chowkhat with shutter without taking off shutte from the frame n exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhat with shutter without taking off shutte from the frame exc 1.5 Sqm and not exc 4 Sqm each complete all as specified and directed.

M&L framed work as in doors or gates angle or other covering door, cooler stand etc to be prepared for handing or sliding with including either hooks and hinges or steel hanging dor fittings (exclusIve of steel or othr covering, running rails and guides) and hanging also fastening and fixing complete conforming to FE-290 Gde E-165 complete all as specified and directed.

S&F factory made solid wooden HDF moulded door shutter 30mm thick (Styles) with 2, 4 or 6 raised panel design with 3mm thick moulded door facing sheet on front face & 3mm thick plain colour door facing sheet on back face with raised high density boiling waterproof fibre board skins, the core shall be consist of solid core using machine filled rigid expanded polyurethane, foam of minimum density 40kg/cum with including additional wooden blocks for fixing of locks etc. The door shall comply with and as per IS-15380:2003 & IS-13205:1991 complete supplying and fixing in frame at site as specified and as directed.

S&F solid PVC door frames of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with printed sheet reinforced with MS Square tube supplying & fixing in opening as per specification and drawing.

S&F factory made moulded PVC door shutter 28-30mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm plain colourprelaminated PVC sheet on the back face, supplying & fixing in frame at site as per specification & drawing.

S&F factory made PVC cabinet made of 18mm thick consisting of panel of 18mm thick celluca ply of density 600 Kg.cbm density with prelaminated sheet on one side cut in desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. Note : Items like cupboard knobs, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing. The measured area shall be front elevation.

S&F 150mm size aluminium handles, cast type, anodised and fixed of approved make & ISI marked.

S&F aluminium anodised barrel tower bolt of extruded section of 200mm size complete all as specified and directed.

S&F 100mm mideum weight butt hinges (type C-21)extruded aluminium alloy with galvanised mild steel hinge pin complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, plate and fixed all as specified.

S&F 5mm thick figured glass pin head type glazing with oil putty area n.exc 0.5 sqm in each pane complete all as specified and directed.

Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 15mm bore complete all as specified and directed.

Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 20mm bore complete all as specified and directed.

Taking down or up steel tubing and connection inculding cleaning for refixing or removal to store 25mm bore complete all as specified and directed.

Supply, fixing, jointing and testing 15mm dia bore galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings including cutting through wall floor etc complete all as specified and directed.

Supply, fixing, jointing and testing 20mm dia bore galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings including cutting through wall floor etc complete all as specified and directed.

Supply, fixing, jointing and testing 25mm dia bore galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings for the following sizes including cutting through wall floor etc complete all as specified and directed.

Refixing old steel tubing and connection in new or old position (walls, ceiling,floor etc) bore of pipe in 15mm dia.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 20mm dia.

S&F in repair vitreous china squatting pan 'Orissa Pattern' of size 580mm x 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe anti syphonage pipe etc complete all as specified and as directed.

S&F in repairs vitreous China wash down water closet (Pedastal pattern) white (excluding flushing cistern and flush pipe incuding seat cover and Jet) including connection todrain or out going pipe and to flushing pipe anti syphonage pipe and making good to floor complete all as specified and as directed.

S&F in repair health faucet, brass chromium plated for EWC/WC with and including connection pipe 1m long suitable for 15mm bore GI pipe with nut and nipple complete all as specified and directed.

S&F in repair vitreous china urinal half stall type white excluding flushing cistern but including CP urinal spreader and waste pipe complete all as specified and directed.

S&F vitrious china urinal partition of size 300mm x 700mm complete all as specified and directed.

S&F in repair vitreous China wash basin (under counter) white of size 550mm x 400mm fixed to granite etc including 32mm dia CP brass waste coupling fitting and union complete all as specified and as directed.

S&F high density polythelene pipe (HDPE) of 32mm, pressure rating 6 Kgf/cm2 fixed to ceiling, floor etc complete all as specified and directed.

S&F repair 10 ltr capacity PVC low level flushing cistern white, ISI marked make as specified with inlet, float valve and handle including breacket with 32mm dia PVC pipe 600mm long complete all as specified and directed.

S&F in repair 15mm dia bore stop /angle valves cast copper alloy chromium plated with long shank complete all as specified and as directed.

S&F repair chromium plated cast copper alloy with crutch and butterfly handle fancy type bib tap (Long Body) & cup 15mm dia bore complete all as specified and as directed.

S&F PVC connection 15mm dia and 450mm long with both ends brass fly nut complete all as specified and as directed.

S&F in repair 15mm dia bore cast copper alloy chromium plated fancy type pillar tap (Swan Neck) for with out cold & hot water complete all specified and as directed.

S&F in repair brass chromium plated towel ring including a pair of CP brass bracket complete all as specified and directed.

S&F in repair soap dish any type of chromium plated complete all as specified and directed.

S&F 1000 Ltr capacity rotational moulded three layers polyethylen water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including S&F 20mm float valve 20mm dia GI pipe medium grade wash out pipe 450mm long with plug and 20mm dia GI pipe medium grade over flow pipe 600 mm long with fitting and including dismantling of tank complete all as specified and directed.

S&F in repair 25mm bore gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up cast iron 75/80mm bore (including all fittings) with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and directed.

Taking up cast iron 100mm bore (including all fittings) with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and directed.

M&L 75mm bore cast iron for soil, waste and vent pipe, any length with or without ears with cement joints fixed to walls or in floors complete all as specified and directed.

M&L 100mm bore cast iron soil, waste and vent pipe, any length with or without ears with cement joints fixed to wallsor in floors complete all as specified and directed.

S&F in repair CI floor trap size 75mm dia outlet with CP grating including connection to waste pipe with lead jointing including taking down existing trap complete all as specified and directed.

S&F in repair CI floor trap size 100mm dia outlet with grating including connection to waste pipe with lead jointing including taking down existing trap complete all as specified and directed.

S&F in repair cast Iron P or S trap 100mm dia outlet waste pipe with cement jointing complete all as specified and directed.

S&F salt glazed stoneware gully trap square shape of of size 100mm x 100mm (P type) complete all as specified and directed.

S&F CI bend any radius 75mm bore complete all as specified and directed.

S&F CI bend any radius 100mm bore complete all as specified and directed.

S&F CI branch piece sigle equal or unequal 75mm bore complete all as specified and directed.

S&F CI branch piece sigle equal or unequal 100mm bore complete all as specified and directed.

S&F CI branch piece double equal or unequal 100mm bore complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed.

M&L vitrified double charged ceramic tiles 8-10mm thick (square/rectangular), polished, coloured, area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L vitrified double charged ceramic tiles 8-10mm thick (square/rectangular), polished, coloured , area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L coloured non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floors etc laid over and including 15mm thick screed bed of cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good, cutting not exc 10cm girth complete as specified and directed.

S&F in reapir 15mm bore, stop valve, chromium plated, fancy type, with long shank, and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in repair fancy type center hole basin mixer without popup waste system but including plain waste coupling 32 mm size with aerator complete cast copper alloy, chromium plated, scrwed down high pressure, with long scrwed shanks & fly nuts scrwed for iron pipes of 15 mm bore complete all as specified & as directed.

S&F in repair brass chromium plated shower rose 125mm size fixed to 15mm bore pipe all as directed.

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges fixed to wall complete all as specified and directed.

S&F stainless steel kitchen plate rack over all size 30" x 31" x 10" and thickness of stainless steel plate 0.60mm, fixed to wall with stainless steel screws complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs washers and wastes including waste pipe fixing cantilever brackets and connecting union to pipe overall size not less than 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as directed.

S&F grating round 100 mm size of stainless Steel complete all as directed.

S&F PVC (SWR) 75mm dia Floor Trap, plain with SS grating including jointing with solvent cement.

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls with Holder bat clamps of GI flat iron 25x3 mm all as specified and directed.

S&F PVC (SWR) bends 110mm dia any radius.

S&F PVC (SWR) junction single (Single T) equal or unequal with access door 110mm dia.

S&F PVC(SWR) Vent cowl 110mm dia.

S&F 75mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors.

S&F 75mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls with Holder bat clamps of GI flat iron 25x3 mm all as specified and directed.

S&F PVC (SWR) bends 75mm dia any radius.

S&F PVC (SWR) junction single (Single T) equal or unequal 75mm dia.

S&F 110mm PVC (SWR) WC connector bent type all as specified and as directed.

Dismantling AC Pipe/ PVC pipes 110mm/ 75 mm dia.

Dismantling water tanks Capacity exc 250 & n exc 500 Litres of any description complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 500 litres capacity three layers ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I and directed.

S&F in repairs 20mm bore ball valves, high pressure, PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron piped and fixed in position all as specified.

S&F in repairs jet spray chromium plated brass for EWC with & including PVC connection 900 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete.

S&F in repair mirror cabinet PVC frame of size 400 x 500 mm fixed to wall with rawl plug & stainless steel suitable size screws complete all as specified and directed.

S&F in repair wall mixer chromium plated (3 in 1) with arrangement for both telephonic shower and overhead shower with 220mm max long bend pipe with hand shower of size 100 x 55mm with 130mm long arm & 1.2 m house pipe complete all as specified & directed.

S&F in repair glass corner shelf (Cat Part No T6010A1 of Make : Parryware or equivalent of Jaquar/Marc) complete all as specified & as directed.

Taking down shutter of any description exc 1 Sqm and n exc 2 Sqm each.

S&F 35mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars) fitted with cut and mitred securing beads for securing glass etc complete as specified and directed sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified and directed.

S&F 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No) complete all as specified & as directed.

S&F stainless steel trollies including cutlary tray, plate rack, utensil tray etc for modular kitchen of any size and shape with all accessories i.e. SS sliding Channel 304 Grade, SS screws etc as approved fixing in position including necessary drilling, PVC cap, self threading screws complete all as specified and directed.

M&L 20-25mm thick single piece kota stone for vertical partition wall/cupboard slab for fixing SS tray and sliding channel including drilling holes and fixing in CM 1:3 all as specified and as directed.

S&F 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with deocrative choice lamination & other side balancing white lamination, including fixed with necessary fittings on kitchen tray / including handle for modular kitchen tray as approved by GE, fixed with screws to timber/steel frame work etc. including taking down existing frame work complete all as specified & directed.

S&F in repairs continuous (piano) hinges, mild steel 30 mm width of flaps, bright finish or electro galvanised complete all as specified & directed.

S&F mild steel cupboard shutter with frame, godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete.

S&F stainless steel butt hinges, 100mm medium weight and fixed all as directed.

S&F butt hinges, cold rolled mild steel, 100mm medium weight and fixed all as directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified & as directed.

S&F aluminium anosided hasp and staple, 100mm size safety type with mild steel hinge pin including to bolt to hinge plate and fixed with screws complete all as directed.

S&F stainless steel curtain rod not less than 20 mm dia with chromium plated including both sides finnials and bracket fancy type fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete all as specified and directed.

Demolition of reinforcement cement Concrete in Roof, floors (other than ground floors), beams, staircase, landing, chajjas and similar suspended work complete all as directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slab n.exc 200mm thick complete all as specified.

M&L form work to edges of concrete flats, treads, breaks in floors, windows cills, concrete railings, floor and roof n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specifed.

M&L use and waste of form work to sides and soffits of chajjas for fair finished surfaces complete all as specified and as directed.

M&L reinforced cement concrete type B1 (1:2:4) nominal mix using 20 mm graded broken stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, shelves and the like complete all as specifed and directed.

M&L reinforced cement concrete type B1 (1:2:4) nominal mix using 20 mm graded broken stone aggregate as in chajjas and the like complete all as specifed and directed.

M&L 7.5cm thick sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc n.exc 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 complete all as specified.

M&L marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Green in colour including 10mm thick screed in cement mortar (1:6) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including rounding the edges and drilling holes for pipes in cooking platform complete all as specified.

M&L 15mm thick rendering in cement mortar 1:4 mixed with water proofing admixture as per manufacturers instructions on fair faces of stone masonry, or concrete surfaces, finished with even and smooth complete all as specified and directed. Note :- Water Proofing admixture shall be measured and paid seperately.

M&L taking down and removal of loose/disintegrated old concrete/plaster and including and applying bonding coat of modified styrene butadiene emulsion (SBR bonding agent i.e. Nitobond SBR 45) in proportion 1(Nitobond SBR 45) : 1(water) : 3(OPC) by volume with the brushes etc to bind 10mm thick new cement plaster/polymer modified plaster /concrete /screed concrete on old wall/ceiling surface etc complete all as per specifications of manufacturer and directed.

M&L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces complete all as specified and directed.

M&L one coat of synthetic enamel paint on old painted wood or wooden based surface exc 10cm width or girth including preparation all as specified and directed.

M&L applying two coat of synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc 10cm width or girth including preparation all as specified and directed.

M&L two coats of synthetic enamel paint on old steel surfaces of any description over 10cm width or girth including preparation all as specified and directed.

M&L preparing new plastered surfaces of walls and applying three coats of white wash complete as specified and directed.

M&L applying two coats of white wash on old decorated surface of walls including preparation all as specified and as directed.

M&L preparing newly plastered surfaces of wall and applying two coats of exterior emulsion (weather coat) over a coat of primer on walls all as specified & as directed.

M&L complete removal of existing treatment of any description & preparation of old surfaces by washing rubbing down and stopping of plastered & making surface good by filling depressions by putty and applying two coat of exterior emulsion of approved shade on walls including cornices etc complete all as specified and directed.

Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding complete.

M&L 150 mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe complete all as specified & as directed.

S&F 50mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 5 ton/Sqm in square, rectangular or circular shape complete all as specified & as directed.

M&L cement concrete 75mm thick 1:4:8 type D-2 using 40mm graded aggregate as in sub base of floors complete all as specified & as directed.

M&L underground sump of capacity 25000 Gallon complete all as specified in drg No CEJZ/TD/2020/S-02 sheet No 1/2 to 2/2 and as directed.

M&L surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil all as specified and directed.

Excavation in trenches n exc 1.5 m wide & n exc 1.5 m depth; for foundation etc and getting out in soft/loose soil complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified.

Removing excavated material n.exc 50M and depositing where directed at a level n.exc 1.5M above the starting point at the descriation of contractor complete all as specified.

M&L 75mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone agg) as in sub base of floor.

M&L machine pressed precast concrete interlocking paver block with grey cement and pigment, of any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 grade complete all as specified and as directed.

M&L chequered cement tiles 20cm x 20cm x 25mm thick set jointed and pointed in neat cement slurry in floors with grey cement and no pigment including screed bed or bedding layer 15mm thick in CM 1:6 complete all as specified & directed.

M&L precast kerb stone built in PCC 1:2:4 type B1 using 20mm graded stone aggregate and including fixing in CM 1:4 complete all as specified and directed.

M&L sand cushioning including spreading and levelling in layer of 25mm thick complete all as specified and as directed.

M&L brick cover of old size brick 'B' class with width equal of the length of the brick laid dry & flat abutted with each other with gap between adjecent bricks bricks not exe 10mm over UG cable for protection complete all as sepecifed directed.

M&L for sand cushioning to PVC UG cable with approved quality of sand.

Supply, laying, jointing /connecting and testing for 80mm bore steel tubing galvanised medium grade pipe with all fittings laid in trenches, complete all as sepecfied.

S&F non return valve cast iron body fianged ends & drilled horizontal heavy duty including jointing material etc complete ISI marked of size 80mm bore for submersible pump as specified as directed.

Supply laying jointing /connecting and testing for 65mm bore steel tubing galvanised heavy class grade pipe with all fittings laid in trenches complete all as directed.

Supply install and commissioning open well horizotal submersible pump for 440V, 3 Phase 50Hz 15 HP confirming to IS-12469 ;1988 with CI casing bronze impeller and stainless stell shaft mounted on heavy duty bearings (Cat Part No : KSB-MR 15 C-80-65-44SD 10 Sqmm or equivelent) complete all as specified and directed.

Supply, install and commissioing of LT panel outdoor type (Kiosk) factory made power coated paint made of 3.15mm thick CRCA sheet,CPRI approved dust and vermin proof protection with 150 Amps copper bus bar for phase and 100 amps for netural,fornt opended with locking arrangements mounted on angle iron frame 40x40x6mm, 45cm height from ground level comparising of the following accessories (a) MCCB 100 Amp 35kv rating 4pole 440Volt -01 No, Make;- ABB/Legrand /L&T (b) MCB 63 Amp TPN 440 V,16 KA -01 No Make:- ABB /Legrand /L&T (c)Starter ,star delta, fully automatic sutible for 15hp 3 phase electrical motor -01 No Make: L&T/ havells /AE (d) Multifunction mater class 1.0 three line bakelite LCD Display with bake sealing arrangement with mater run hour & power on hour, AVG, Max & total value of active, reactive & apparent power spen shot of power (KW), Current (I) Voltage (V) & PF with programmable CT ratio of -/5 A alongwith suitable size core CTs for current sensing (Make HPL ,Cat part No NEMFVIFPPE000 or equivalent of Make :-L&T/Secure /conserv (e) Single Phase preventor mini lec VSP-II-01 No, Make:- Havells /ABB/ L&T/C&S (f) Phase sequence corrector 15 HP motor, 3 Phase-01 No, Make:- Havells /ABB/ L&T/C&S (g) Indication lamp 22.5mm dia LED type 240 volts AC to show three phase availability-01 Set (h) Wiring with suitable size copper conductor cable not less than 6 sqmm PVC sheathed copper conductor for LT panel (j) Power factor correction capicitor bottle type, 3 KVAR, 3 Phase- 01 No, Make:-Legrand /ABB/EPCOS Note : Quoted rates shall be deemed include for grouting /fixing of bus bar chamber in PCC 1:3:6 type C2 and PCC block masnory with PCC block of mix 1:5:8 plastering 10mm thick in CM 1:6 complete all as specifed and directed.

S&F 1100 volts grade submersible cable flat 3 core with copper conductor 10 sqmm stranded fixed to motor to panel complete. Make:-Havells /finolex /polycab

Supply & laying in treches or passing through pipe /fixed to pole /wall pvc insulated and PVC sheathed armoured heavy duty elecrial cable with multistranded aluminium conductor 1100 volts gred 35sqmm 4 core.

M&L GI pipe (light grade) for protection of LT cable fixed to wall / poles / road crossing Including clamps complete of size 50mm bore.

M&L earthing to electric equipments/panels with and including galvanized MS earth plate electrode of size 600 x 600 x 6mm thick burried vertically in ground to a depth not less than 2.25 metre below ground level, with top edge of earth plate not less than 1.5m below ground level as shown in electrical plate No 3 of SSR Part I, the earth plate surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all sides, excavation & earth work in any type of soil and removal of surplus soil upto 50m including galvanized mild steel strip 25 mm x 4mm as earth lead, welding at top of electrode and other end of strip connected to equipment body/panel/test point with two Nos nuts bolts or welding with steel structure, GI earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 3.00 metre above ground level fixed along equipment body/panel with and including 25x3mm FI clamps, bolts, nuts and washers, PCC chamber (1:3:6) type C1, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering, 75 mm thick RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

S&F 80mm bore cast iron foot Valve flanged ends, swing type opration with rubber Sheet as per IS: 4038 including taking out unserviceable foot valve completed all as specifiled and directed.

M& connection GI pipe line to CI/ GI water mains of size 80/100 mm dia with CI/GI joints & fittings and necessary connecting accessories completed all as specified and as directed.

S&F sluice valve, cast copper alloy, PN 1.6 of size 80mm dia complete including connecting . Make : Kirloskar /Upadhayay /BVR

Taking down carefully copper/aluminium point wiring for one light /socket/power point and taking down of teak wood batten/ PVC casing caping and making good disturbed surfaces of walls/ ceiling/ floors etc including dismentling of fittings complete all as specified.

M&L point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke & heat (FRLS) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20mm external dia) but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part-I, ISI marked with wall thickness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLS PVC insulated unsheathed copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakellite white/coloured top sheet cover 3.0 mm thick for one light point controlled by one way switch all as specified & directed. Note : The quoted rate shall be incuded cutting, chasing, making good of distrub surfaces including matching of existing colour surface of walls.

All as per serial item No 180.00 here-in-before but for one fan /exhaust fan point controlled by one switch and regulator.

All as per serial item No 180.00 here-in-before but for one bell/buzzer point controlled by one bell push.

All as per serial item No 180.00 here-in-before but for one light point controlled two, two way switch.

All as per serial item No 180.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No 180.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 180.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

All as per serial item No 180.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 4.00 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 4.00 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 250 Volts module type complete all as specified and directed.

S&F switch piano flush type, single pole, two way, 5 Amp, 230 Volts module type complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15/16 Amp, 230 Volts module type complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 Volt Module type complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 6 & 16 Amp, flush type 240 Volt module type complete all as specified and directed.

S&F bell push 5 Amps 240 Volts single pole moduler type.

S&F multi music type AC 230 Voltssingle pole moduler type.

S&F PVC white cover plate with frame, 2 module.

S&F PVC white cover plate with frame, 3 module.

S&F PVC white cover plate with frame, 4 module.

S&F PVC white cover plate with frame, 6 module.

S&F PVC white cover plate with frame, 8 module.

S&F modular metal flush box, 2 module.

S&F modular metal flush box, 3 module.

S&F modular metal flush box, 4 module.

S&F modular metal flush box, 6 module.

S&F modular metal flush box, 8 module.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 Volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 6 & 16 Amp, flush type 240 Volt complete all as specified and directed.

S&F ceiling rose surface bakelite 65 x 50mm two or three terminals complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed.

S&F stepped type electronic fan regulator, flush type and connecting up ISI marked 240 volts complete all as specified & directed.

S&F lamp holder PVC/Polycarbonatetype with back plate suitable forbatten fittings complete all as specified.

S&F LED bulb 10/11 watt complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 4 way, 240 volts complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 2 way, 240 volts complete all as specified and directed.

S&F MCB 32/40 Amps, single pole & neutral, 240 Volts, 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002, Ingerted label holder, sliding bottom clamp improved air channels, colorb coded On/Off indication on dolly IP 20 protected terminals, DC-80V per Pole-1KA complete all as specified and directed.

S&F MCB 6-40 Amps, single pole, 240 Volts, 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002, Ingerted label holder, sliding bottom clamp improved air channels, colorb coded On/Off indication on dolly IP 20 protected terminals, DC-80V per Pole-1KA complete all as specified and directed.

S&F exhaust fan complete of 300mm sweep 240V AC including provision of hole in wall of suitable size for fixing of exhaust fan all as directed.

Taking down and refixing ceiling fan complete of any sweep 240V, AC and connecting up with necessary wiring of 3 core flexible copper wire complete all as specified and directed.

S&F AC box single pole and neutral enclosure with a two pin and socket complete with one single pole MCB 240 volts, 32 Amps.

M&L sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked (IS: 694) cables, drawn through & including suitable size of heavy duty PVC conduit ISI marked not less than 32mm dia (external) with wall thickness not less than 1.8mm & conduit fittings /accessories, fixed on surfaces of wall/ceiling complete all as specified and directed. Note:- 02 runs of 6 sqmm size, 01 run of 6 sqmm size cable & conduit with accessories shall be measured as one run length for payment purpose.

M&L aluminium powder (thickness of powder coating not less than 50 micron) as in frames of door/ window/ ventilators with one or more rebates, including joining cleat for fixing etc with all necessary screws, roll plugs etc all as specified and directed. Note : (i) Weight of aluminium section shall be measured. (ii) The supply only rate of glass will be measured separately.

Hitesh Construction

shiva construction