PROVN OF CERTAIN MINOR WORKS IN THE AOR OF AGE B/R-II UNDER GE (EAST) DELHI CANTT-10

Amount

Surface excavation not exc 30 cm deep and ave 15 cm deep and getting out in soft/loose soil complete all as specified.

M&L for Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation etc or for shafts, wells, cesspits etc not exc 10 sqm on plan and not exc 1.5 mtr in depth and getting out in soft/ loose soil complete all as specified

M&L for Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm in soft/loose soil complete.

M&L for Removing surplus excavated soil to a distance n-exc 50 mtr & desposting where directed at a level n-exc 1.5 mtr above the starting point complete

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete.

M&L for 40mm thick DPC in cement concrete(1:2:4) B-type(12.5mm graded aggragate) to horizontal & vertical surface including necessary form work and complete all as specified & directed.

M&L for Polythen film 50mm thick micron laid with a coat of bitumin primer @0.30to 0.50 Kg per Sqm on DPC complete all as specified and directed.

M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) for Columns, pillars, piers, posts and struts complete.

M&L for Form work to flat sided of pillars, post,struts columns,square,rectangle or polygonal etc. rough finished surfaces complete all as specified & directed

M&L for Use and waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressumers, lintel beams/lintel band , cantilever and similar work rough finished surface of concrete complete all as specified and directed.

M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) for Beams, cantilevers, bressummers, lintels over 1.5m span complete.

M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) concrete as in as in slabs (roof) supported on walls, beams and columns , landings, and in shelves and the like complete all as specified and directed.

M&L for Use & waste for form work to soffits of suspended slab such as roof slab, floor slab , landing and similar work; not exc 200 mm thick horizontal or sloping, finished rough and even complete all as specified and directed.

M&L for Form work to edges of concrete flat,treads,breaks in floor window cills concerte railing,opening in conmcrete walls, floor and roof and similar work exc. 10cm but not exc. 20cm wide complete as all specified & directed

M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) concrete as in Chajjas and the like complete all as specified and directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges

M&L for brick work with sub class 'B' straight or curved on plan exc 6m mean radius and built in CM 1:4 complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, finished fair and even by applying 3 mm thick wall care putty complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 and mixed with WPC on fair faces of brick work or concrete surfaces finished fair and even complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only under relevent item of this schedule)

S&F MS TMT steel bars 5 mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

S&F MS TMT steel bars 10 mm dia and over, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for prepration of new plastered surfaces of wall and applying of Birla/JK white wall putty approx 2 mm thick as per manufacturer's instruction on existing prepared surface and make the surface smooth by rubbing with sand papers etc and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces. complete all as specified and directed.

M&L for preparing new plasteres surfaces and applying of Birla/JK white wall care putty approx 2 mm thick as per manufacturer's instruction on existing prepared surface and make the surface smooth by rubbing with sand papers etc and applying two coats of Plastic emulsion paint over a coat of primer of walls Surfaces complete.

M&L for preparing new plasteres surfaces ceiling and applying of Birla/JK white wall care putty approx 2 mm thick on ceiling as per manufacturer's instruction on existing prepared surface and make the surface smooth by rubbing with sand papers etc and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and directed.

S&F Decorative type cornies of suitable width on wall and ceiling edges/ corners with plaster of paris sheets fixed with machine screws including prepration of surface and applying one coat primer and two coat of plastic emlusion paint, complete all as specified and as approved by Engr-in-Charge.

S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm center to center/ Intermediate channel 0.9 mm thick having to equal flanes of 15 mm each and web of 45 mm suspended from soffit at approx x 900mm center to center with GI cleat and steel expension fastners with and including ceiling section ( not exc 1.2m length ) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50 mm fixed to the intermediate channel at 457 mm center to center. Including Hangers 6mm dia GI up to 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI Flat 40x3mm size 60mm long and expansion hold fastners 12.50 dia. 40 mm long complete all as specified and as directed.

S &F Providing and fixing 10 mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class hard wood fillets, or metal frame and work with GI wire mesh( fillet, Metal frame work and GI Wire mesh paid seprately) including sunk or raised mouloding complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in floor sub base complete all as specified and directed.

M&L for Non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:6) complete all as specified

M&L for Glazed ceramic coloured tiles in vertical surfaces 350 X 250/450 x 350X 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match over and including 10mm thick CM (1:4) in dado/skirting tiles complete all as specified and directed.

S&F 15 mm dia fancy type CP bib taps half turn with wall flange with screwed down, screwed for iron pipe or for brass ferrule including cap and fixed complete all as specified and as directed by Engineer-in-Charge. (Make: Jaquar/Marc/Kohler)

S&F 15 mm bore fancy type angle valves half turn chromium plated fancy type with wall flange screwed down high pressure screwed both ends for iron pipes or for unions complete all as specified and as directed by Engineer-in-Charge (Make-Jaquar Cat Part No. ORM-10053/MARC or Equivalent in Marc/Kohler)

S&F 15 mm bore brass CP single lever Basin mixture for Mixing Hot and Cold water fixed as per manufacture’s manual, with long shunk and cup washers, screwed both ends for iron pipes or for unions complete all as specified and directed (Make : Jaquar Cat Part No. OPL-15011Bor Equivalent in Marc/Kohler).

S&F vitreous china wash basin over counter ovel type size 600x425x195mm jaquar, hindware or equivalent fixed over granite slab with all fitting and fixture complete all as specified.

S&F in repairs 32mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed.

S&F 15 mm bore 2 way angel valve with wall flange complete all as specified & directed (Make: Somany Cat No 220909/CERA Cat No 2008211, MARC MJN-1410 or Equivalent in Marc/Kohler).

S & F CP Toilet Paper holder with flap guard complete all as specified and directed Make Cera Cat No F5003110/Somany Cat No 230507/Hindware F-880003)

S&F CP Brass soap dish complete all as specified & directed (Make Hindware Cat No F880011/Cera F5003106 or equivalent in Jaquar)

S & F Corner Glass Shelf 300 x 300 mm radius consisting of 5.5mm thick sheet glass with chromium plated brass brackets with two No CP Railing in each set complete all as specified and directed (Make: Cera Cat No F5005103 or equivalent Marc/Kohler).

S & F CP Health Faucet with 1.00 Mtr long CP Flexible pipe as per approved sample complete all as specified and directed Make Hindware Cart Part No F160001/Marc Cat No MAC-3052 Cera Cart No F8030103 or Equivalent.

S&F Vitreous china wash down water closet pan wall hung WC 2049 EWC Wall hung Ext. 'P" 655 x 390 x 745 mm cistern 2129 , shoft closed seat cover2356 and 2238 twin flush fitting of Cera , hindware , Jaquar or other equivalent including flushing cistern and fixed with brass screw complete all as specified and as directed.

S&F CP towel rail 600mm long complete all as specified and as directed by Engineer-in-Charge complete all as specified and directed. (Make: Jaquar/Marc/Kohler)

S&F 450 mm long PVC connection with stainless steel armed 15 mm bore with nuts complete all as specified and as directed by Engineer-in-Charge complete all as specified and directed.

M&L earth filling under floor/ floor finishes including spreading and levelling in layers not exc 25 cm thick for well ramming including watering as required complete all as specified and directed.

M&L for hard core of broken stone or boulder of gauge not exc 63mm, deposited, spread and level in layers not exc 15cm thick watered and rammed to a true surface complete all as specified and directed.(75 mm. thk.hardcore n rcc 63 mm. )

M&L for 75 mm thick cement concrete 1:3:6 type E-2 (using 40 mm graded stone aggregate) as in plinth protection laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges rough or rounding or chamfering of exposed edges where directed and providing 6 mm thick joints through the thickness of plinth protection duly filled with mastic filling of one part of hot bitumen 85/25 grade and three parts of fine sand (all by weight) complete.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

M&L Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing; frame work for water tanks and similar work conforming to Fe 290 Gde-E-165 all as specified .

S&F in 10 mm thick slected quality toughned glass cut to size and shape including chamfering of edges cutting holes/ slotes for fixing in doors/ windows with all necessary fixing arrangement complete all as specified and directed. Make - Modi, saint gobin or equivalent.

S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15 mm dia.including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete I:2:4 complete all as specified and as directed by Engineer-in-Charge

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar1:3 in brick or stone wall , cutting not exc 10cm girth complete.

All same as per item No 54 here-in-before but 20 mm dia complete all as specified and as directed by Engineer-in-Charge

PVC (SWR) floor trap, plain with grating including jointing with solvent cement all specified & directed 75mm bore complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in wall/trenches or in floors 110 mm bore complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in wall/ trenches or in floors 75 mm bore complete all as specified and directed.

PVC (SWR) reducers all specified & directed 110 mm dia complete all as specified and directed.

PVC (SWR) vent cowl all specified & directed 110 mm dia complete all as specified and directed.

110mm PVC (SWR) WC connector bent type all as specified & directed

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified & directed

S&F rotantional moulded polythylene water storage tanks 1000 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore omplete all as specified and directed.

M&L for PCC 1:2:4 type B-O using 12.50 mm graded stone agg with WPC as in padding to maintain proper slope as required all as specified (WPC shall be paid seperatly.)

M & L for providing and applying smart care Dampproof, a fidre reinforced elastometric liquid water prrofing membrane formulated with reinforced acrylic fibres having Sun Reflective Index (SRI) of 105 on horizontal/ vertical surfaces of roof/ wall/ chajjas in multiple costs @2.0 litre/ sqm. Primary coat is self-priming coat of elastomericwaterproofing liquid (Dilition with water in the ratio of 3:1, damp proof : Water) and other coat to be applied undiluted. The coating needs to be reinforced with 40GSM Geotextile, to sandwiched between 2nd &3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Cgarge. Make : SmartCare Damp Proof of Asian or equivelent in Berger/ Nerolac/ STP/SIKA/FOSROC only. Notes: (1) The work shall be executed through authorised appplicatot of manufacturer only. (2) Authorised Applicator shall be approved by GE befor starting the work. (3) All materials shall be produced directly from manufacturer. The purchase voucher shall be produced to the Engineer-in-Cgarge for his verification of material. Engineer-in-Cgarge shall deface the original purchage vouchers. (4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water Proofing treatment for a period of Ten years in favour of GE. A sum equivalent to 2.5% ( Two point five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor's duues as security deposite. The contractor may, however, furnish a fixed deposite receipt in lieu from a Schedule bank pledged in fevour of Garrison Engineer.

M & L for rendering 15 mm thick in cement mortor 1:4 over PCC bedding with water Proofing compound and finishing the surface even and fair without using extra cement complete all as specified directed. (Note: WPC shall be measured and paid separately as supply only under relevent item of this schedule)

M&L for Type C1 20mm graded 1:3:6 in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed.

PCC (1:2:4) (40MM GRADED AGGRAGATE) in surface channel of drain complete.

S&F vitreous china urinal of of cat No. URS - WHT - 0704 of size 710 x 485 x 300 mm with Sensotronic sensor SNR - CHR - 51097 flushing valve for urinal with complete kit of make Jaquar/Cera/Hindware with all fitting and fixture complete all as specified.

S&F in 15 mm thick slected quality toughned glass Plain or full frosted cut to size and shape as per site requirment for fixing in doors, windows, hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes required and includind all necessary fixing arrangement for partition or door and with lock and self closing device (Fixed type windows should be MS framed powder coated with Georgin pattern) as approved and directed by Engr-In- Charge complete all as specified and directed. Make - Modi, saint gobin or equivalent.

S&F Door handle H type 25x300mm (Model No-IGH- 55 of make. Insta or equivalent as approved by GE complete all as specified and as directed.

M&L for Grinding, polishing /bevelling of edges on 12mm thick toughened glass complete all as specified and as directed.

Demolition and breaking up SGSW drain pipes 150 mm dia jointed in cement mortar all as specified.

M&L SGSW drain pipes 150 mm dia laid in trenches and jointed in CM (1:3) complete all as specified and directed by Engr-in-Charge.

M&L cement concrete bed (1:4:8) type D-2 using 40mm graded stone aggregate as in bedding to SGSW NP-2 pipes 150mm dia to drain pipe including formaing cradels in complete all as specified and as directed.

Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed.

S & F Stop valves 20mm Dia, but fancy type, chromium plated with long shank and cup chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. (Make: Jaquar/ Marc/Kohler)

Supply only liquid water proofing compound complete.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floors finished rough all as specified.

M&L for Vetrified ceramic tiles ultra charged (dark shade) 10mm thick (square/rectangular) area of each tile exc 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:4) complete all as specified

All same as per srl item No. 82 here-in-before but on vertical surfaces such as skirting / dados with and including 10 mm thick CM 1:4 as in backing coat complete all as specified.

Taking down cement plaster /duster bed PCC of Column, chajja, Parpapets of roof, facia, drops etc and making good with cemnet plaster 10mm thick in CM 1:3 with PCC 1:2:4 type B1 (average thickness of PCC 25mm) as required, brushing with neat cement slurry @ 3.0 Kg of cement per Sqm including necessary form work and scaffolding upto 2nd floor including fixing of wire netting where required to match the existing surface complete all as specified and directed

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 sqm and n. exc. 4.00 sqm each complete all as specified and directed.

Taking down chowkat or frames n. exc. 1.5 sqm each with shutters (without taking off shutters from frames) complete all as specified and as directed.

Box type Steel windows with double shutters (inside for wiremesh & out side for glass), hinges, steel handle, tower bolt and steel peg stay complete with glazing bars dovetailed or welded .WIRE MESH –Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperature 1.40mm. Grills window shall be provided with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate . Distance between bars should not be more than 12cm c/c. Total grill unit shall be enamel painted and fixed to window frame with screw . Note: The glazed/Guaged shutter includingguard bars shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof and guard bars shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive two coat of paint over a coat of primer of all aspects incl all fitting,glass,wire mesh,guard bar , as specified in Drg No CEDZ/TD/289 sheet 1 R/2 and 2R/2.

S&F 35mm thick flush shutter, solid core construction, with block board core and plywood face panel commercial type on both sides.

S&F mild steel butt hinges medium weight cold rolled of size 100 mm shutters. complete all as specified and as directed.

S&F Extruded Aluminium alloy handle fabricated type, anodised of size 150mm. complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm. complete all as specified and as directed.

S&F Aluminium alloy, anodised sliding door bolt, with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sloding bolt of extruded section or cast alluminium alloy of size 250mm. complete all as specified and as directed.

M&L for preparing new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. complete all as specified and as directed.

M & L for PCC 1:3:6 type C-2 ( Nominal mix) using 40 mm graded stone aggregate as in foundation filling, mass concrete and similar work complete all as specifed and as directed.

M&L for Type B1 20mm graded 1:3:6 in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed.

M&L for Rendering 15mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces and finished the surface even and fair complete all as specified.

M & L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base 75mm thick complete all as specified and as directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, in soft/loose soil complete all as specified and directed.

Cutting holes in brick walls exc half brick but not exc one brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, all as specified.

S&F 8mm thick poly corbonate reinforced colourd plain sheeting as in roof coveing fixed with coach screw and washer in existing frame work complete all as specified and directed

M & L for cement concrete type B-2 1:2:4( 40 mm graded aggregate) in foundations, filling and mass concrete.

M&L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment conforming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as specified and directed.

M&L for 50mm thick sand cushion/Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Taking down cement plaster on brick walls etc including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L 12-15mm thick polymer modified readymix cement base plaster as per manufacturer instruction on fair / unfair faces of brick work or concrete surfaces & finishing the surface even & fair as per manufacturer instruction complete all as specified & directed.

M&L for prepration of newly plastered surfaces of wall and applying 2mm thick birla white wall care putty complete all as specified and as directed.

M&L for MS rolled section as in main and cross beams, hip and jack rafters , purlins, where connected to common rafter, post and running rails and guided for sliding doors fixed with angle cleats and other connecting plates complete all as specified.

S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for preparing new Steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamalle paint over a coat of red oxide zink chrome primer. complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0 kg of cement per sqm.

M & L for OUT DOOR/Parking coloured ceramic tiles 8 to 9 mm thick (square/rectangular) area of each tiles exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified MAKE-ENDURA BY NITCO OR EQUIVALENT

M&L for Providing, cement concrete type B-1 1:2:4 (20 mm graded aggregate) in mud stops, rounded or chamfered on edge complete all as specified and directed by Engineer-in-Charge.

Supply only Stainless steel thali basket (11-13 division) of size 50cmx37cmx20cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved Make: Life style Cat part No WA/TB/15208 or equivalent approved

Supply only Stainless steel Plate basket (11-13 division) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved. Make: Life style Cat part No WA/PTH/15206 or equivalent approved

Supply only Stainless steel Cutlary basket of size 50cmx37cmx10cm made of 4mm th S.S.wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing Telescope basket (channel) 18''/20'' length two way extruded MS galvanised over rollers of approvedMake: Life style Cat part No WA/CUT/15204 or equivalent approved

S&F Telescope basket (channel) 450/ 600mm length of extruded MS galvanised rollers of approved quality

M&L in repair for Modular kitchen & Wardrobe / cupboard with 18 mm thick one side decorative and other side balancing lamination factory pressed HDHMR Board leives of action Tesa and equavalent including 2 mm thick PVC edge banding tape with hot glue by edge bending machine etc with auto closing spring loaded hinges (hydraulic) type) etc or sliding sliding with track arrangement as directed including necessary accessorise like Brass handle, Magnatic catch etc and steel baskets of required size mounted on suitable channels with ball bearing to moving of baskets smoothly including all necessary fittings and fixture and 8mm thick both sides Preliminated BSB (Both side balancing proper ) HDHMR of Action Tesa and equavalent as per IS:14587:1998 fixed complete all as specified. (Note: Baskets will be measured and paid separately as supply only).

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl fixing with adhesive in apropreat platform complete all as specifed and dircted.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specifed and dircted .

S&F in repair sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm with & including one waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement ,with PVC coupling, PVC waste pipe 40mm bore 750mm long complete all as specified and directed. Cat part No:-. BSSBSD-52 of Make Blue Star or equivalent model in specified makes as approved by GE.

S&F 15 mm bore brass CP single lever Sink mixture for Mixing Hot and Cold water fixed as per manufacture’s manual, with long shunk and cup washers, screwed both ends for iron pipes or for unions complete all as specified and directed (Make : Jaquar Cat Part No. LYR-38309 /Hindware F-280020CP or equivalent in Marc/ Kohler).

S&F gun-metal stop cock 20 mm bore, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete

S&F CP towel ring complete all as specified & directed (Make : Cera Cat No 5004105/Hindware Cat No 880007, Somany Cat No 230703)

S&F in repair for 15 mm dia fancy type CP Stop valves, Cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge (Make: Jaquar/Marc/Kohler).

S&F over head shower rose CP Brass with shower arm for 15mm bore pipe of size 150x150mmcomplete all as specified and directed (Make :- Somany Cat No 240406/ CERA –F7010506/ Hindware-240806)

S&F for Towel Rack with Lower Hanger (Stainless Steel) with hook. (Make: Jaquar, Cat I. No. AHS-1581H or equivalent in Marc/Kohler).

S&F in repairs wall mixer 3- in - 1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe connecting legs and wall flange with hand and overhand shower with all fittings and fixtures, flexible tube 8mm dia and 1.50m long with nuts,Hand shower 105mm dia round shape single flow with air effective(ABS body and Face plate chromium plated) with rubit cleaning system complete all as spd. (Make Jaquare Cat No : FUS- 2928, OHS - 35495, SHA- 549D8, HSH 1775 & Cat No. SHA- 455L400 or equivalent in Marc/Kohler)

Dismantling wall and ceiling boards ( fibre pulp, insulation etc ) or insulation boards/ slabs/ blank ets, any thickness, incl cover fillets all as directed.

M&L for aluminium anodised snap grid frame work of size 605x605mm for false ceiling with hanging arrangement of 6mm dia G .I ( u p to 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size and 60mm long and expension hold fastners 12.50mm dia 40mm long complete all as specified and directed.

M&L for Non asbestos 4mm thick fibre cement building boards fixed or laid / inserted to aluminium frame work with screws as in false ceiling fixed in ceiling flat or sloping complete all as specified and directed.

M&L for Glazed coloured ceramic tiles in vertical surface as in dado 600 x 300 x 7 to 8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Demolition of reinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for rendering 10 mm thick plaster in CM 1:3 on ceiling finished even and fair complete.

M&L for rendering 15mm thick plaster on wall in CM 1:6 finished even and fair complete.

M&L for preparation of newly plastered surfaces of wall and applying two coats of acrylic emulsion paint over one coat of interior primer and one coat of 1mm thick wall care putty complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of acrylic emulsion paint over one coat of interior primer and one coat of 1mm thick wall care putty complete all as specified and as directed.

Taking up or down 15mm dia steel tubing and connection incl cleaning for refixing or removal to store.

S&F in repair fancy type chromium plated brass bib cock with flange with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete Make : Prayag Cat Part No 7305 or equivalent in Jaquar/Somany/Cera as approved.

S&F in repair fancy type angle Stop valves cast copper alloy chromium plated screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipes or for unions, 15mm dia of pipe, complete.

S&F in repair 15 mm Brass CP mixer (sink) for mixing hot & cold water screwed down for iron pipe and fixed complete. (Make: Jaquar/ Marc/Kohler)

Supply only Stainless steel Cutlary basket of size 370mmx485mmx100mm made of min 4mm dia stainless steel wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing telesscopic basket over channel 18 inches/20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat Part No 6132 or equivalent approved by Engr-in-Charge,

Stainless steel thali basket of size 370mmx485mmx200mm made of min 4mm dia stainless steel wire of approved quality with suitable arrangement for fixing telescopic basket over telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat Part No 6136 or equivalent approved by Engr-in-Charge.

Stainless steel basket (plain) of size 370mmx485mmx150mm made of min 4mm dia stainless steel wire of approved quality with suitable arrangement for fixing telescopic basket over telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat Part No 6121 or equivalent approved by Engr-in-Charge.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240

M&L for prepration of New/Old plastered surfaces of wall and applying two coats of cement base paint over a coat of Primer complete all as specified and directed .

S&F 35 mm thick , 2nd class hard wood factory made, rail and style, plain framed, panneled shutter (three panel) lock rail and panel of 12 mm BWP ply commercial on both faces. The size of rail and style as per IS-1003 (part-I), kiln seasoned and chemically pressure treated. complete all as specified and directed.

S & F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S & F of factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam coloured PVC Sheet on both face, supplying & fixing in frame at site as per secification & directed

S&F MS angle iron as in door framed work with Hold fast conforming to Fe 290(Gde E-165) including tie rod, hinges including one shop of red oxide primer etc. complete.

M&L 40mm thick PCC 1:2:4 type B-1 (20 mm graded stone agg) as in Floor base finished even and smooth at top without using extra cement etc complete all as specified and directed.

All same as per item No. 152 here-in-before but 20 mm mm dia.

S&F in repairs looking mirror size 600x450mm mounted on 6mm thick PVC sheet and aluminium frame all around incl fix with necessary fixing arrangement complete all as specified and as directed.

S&F in repairs Vitreous China squatting pan 'Orissa' pattern,size 580x440 mm white with integral foot rests (excluding flushng cistern and flush pipe) and all as directed by Engneer-in Charge.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with linlet,ball valve, float and handle including brackets, With flush pipe complete all as specified and directed.

M&L rendering 15mm thick cement plaster in cement mortar (1:6) finished even & fair on brick/ concrete surface complete.

M&L for preparing new/ old plaster surfaces wall and applying of Birla/ JK white wall care putty approx 2mm thick on wall as per manufacturer's instructions on existing prepared surface ans make the surface smooty by rubbing with sand papers etc and applying tow coats of Oil Bound Distemper over a coat of primer paint on wall complete.

Material and labour of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and fittings such as tees, bends, elbow, and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly including Metal Flush Box, Cover plate with frame, cutting chases and making good disturbed surface in CM 1:3 to match with existing surface complete all as directed for the following:-

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

All as per Srl Item No 162 here-in-before but with 4 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for independent point.

S&F Modular switch 6 Amp, 1 way, 1 module size complete all as directed..Make-Indoasian shynora,Anchor Roma,Legrand Avtear or equivalent.

S&F Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed..Make-Indoasian shynora,Anchor Roma,Legrand Arteor or equivalent.

S&F Modular switch 16 Amp, 1 way, 1 module size complete all as directed.Make-Indoasian shynora,Anchor Roma,Legrand Arteor or equivalent.

S&F Modular socket 16 Amp multipurpose shuttered type, 2 module size with indicator lamp complete all as directed. (Make-Indoasian shynora,Anchor Roma,LegrandArteor or equivalent).

S&F Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

S & F surface and wall mounted LED tube light fitting with Aluminium housing & interated electronic driver with tube rod of 20 Watt. slim elegant design.and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector all as specified and directed.

S & F LED energy efficient integrated battens fittings, Aluminium extruded heat sink with shatter proof opal shell of Aluminium housing, 10 Watts, cool/warm white as per site requirement, complete all as specified and as directed.

S&F of LED bulk head fitting 10W with inbuilt driver complete all as specified and directed.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.Make Eveready,Crompton,Havell or equivalent.

S & F of Wall Mounted Fan 400 mm sweep plastic body type including making all electric connections and complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm complete.

S & F of MCB DB conforming to IP 43 - IK 09 with double door , SPN 8 way complete with din rail Neutral and earthing bar complete all as specified and as directed.

S&F of MCB SP, B Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F of MCB SPN B Curve type, 10 KA, 63 Amp, with over load and short circuit protection complete all as directed.

Supply and fix Automatic Hand drier hot air dispenser with infrared sensor metal body with all accessories including all electrical connection complete all as specified and as directed.Make-Euroforce or equivalent.

M&L for sand cushioning to under ground cable provided with layers of snad(8 cms deep before laying the cable and 15 cms deep after laying) complete allas specified and directed at site by Engineer-in-Charge.

Supply and laying burnt bricks class - B for protection of cable complete all asspecified and directed at site.

XLPE insulated armoured heavy duty U/G aluminium conductor cable served with an inner sheathing of PVC tape armoured with galvanised steel strip wire or tape and overall PVC sheathed of size 10 Sqmm 2 core, complete all as specified and as directed.

Earthing complete with galvanised steel plate electrode 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level , connected to and including galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, washers protected by and including 15 mm bore GI Pipe “light grade” and connected to main test point as directed and including concrete pit in PCC(1:3:6) type C1 precast RCC M-25 (design mix) precast cover slab (54 x 54 x 5 cm) duly reinforced with and including 8 mm dia TMT steel bars @ 150 mm C/C both way, one lifting handle made of 8 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI medium grade pipe for watering, charcoal and salt in alternate layers, including necessary excavation and earth work any type of soil complete all as specified and shown in electrical plate No. 5 of SSR Part –I including testing on completion complete all as specified and directed.

M/s Shubh Enterprises (BID ID -3394764)

aggarwal engineers contractors (BID ID -3393778)

PRAGATI BUILDERS (BID ID -3394348)

Akhil Enterprises (BID ID -3395084)