RENOVATION OF CERTAIN SMQS AT AF STN CHANDINAGAR AND AOR OF GE (AF) FARIDABAD

Amount

Taking down chowkats or frame with shutters (without taking off shuttters from frames) size exc 1.5 Sqm but not exc 4 sqm each each and removing from site and making good disturbed surfaces as per existing specifications complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frame with shutters (without taking off shuttters from frames) size n .exc 1.5 Sqm and removing from site and making good disturbed surfaces as per existing specifications complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in opening complete solid PVC door frame of size 50mm x 47mm made out of 5mm one side prelaminated any colour PVC sheet reinforced with MS square tube complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for factory made solid panel PVC door shutter 30mm thick(Style) consisting of frame made out of M.S. tube for top & bottom rails. M>S frame shall be covered with heat moulded prelaminated decorative any colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside wqith solvent cement for stiles and prelaminated colour PVC sheet for top rail, Lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelaminated decorative colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement fixing in frame at site complete all as specified and directed by Engineer-in-Charge.

S&F window or ventilators section of frame 72x55mm fixed to wall or concrete surface with rowl plugs made of galvanised steel powder coatd and section of shutter 47x20mm, mulion section 72x50mm ( Based steel as per IS 513 "D" qualilty galvanised as per IS 277 with zinc of 120 gms/sqm) glazed and gauged or wire gauge shutter prepare to receive wire mesh to the shutter (double bars powder coated fixed to window frame with screws including necessary fitttings and all builders harware such as alldles, tower bolts and stays etc complete all as specified and directed by Engineer-in-Charge. (Make : NCL type-4000 series (Note : Glass and wiremesh shall be measured and paid separately under respectibve tiems.)

M&L 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 sq.m in each pane complete all as specified and directed by Engineer-in-Charge.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

M/L for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 complete all as specified and directed by Engineer-in-Charge.

S&F powder coated aluminium frame of standard section for doors, windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

S&F powder coated aluminium window and ventilator shutters , side hung type / sliding without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, ruber packing , anodised aluminum snap beading , screws, anodised aluminium fittings such as peg stays 150mm long (1nos). hinges type B-21 100mm long (2nos) suitable handle (1nos) complete all as specified and directed by Engineer-in-Charge.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm each pane complete all as specified and directed by Engineer-in-Charge.

S&F for 30mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc (without sash bar) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as per SSR-Part-I Section-8, Clause 8.24 (a) etc complete all as specified and directed by Engineer-in-Charge.

S&F for factory made 35mm 2nd class hardwood Plain, framed panelled shutters (any No of panels) with lock rail and panel of 12mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F for Pressed steel frames of size 125 x 60mm for doors , windows and ventilators etc, with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge.

S&F for Pressed steel frames of size 105 x 60mm for doors , windows and ventilators etc, with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing mild steel butt hinges, 100 mm long, medium weight, cold rolled fixed with steel screws or welded to angle iron frame where required complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 125 mm aluminum handles cast type anodized complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar in any position including all quoins, arches & pillars etc complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering 15 mm thick in CM 1:6 on fair faces of brick or concrete surfaces of walls, facia etc to be finished even and smooth (w/o using extra cement) complete all as specified and directed by Engineer-in-Charge.

Material and labour for 15mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces of walls finished even and smooth w/o using extra Cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with chalk whitening preparatory to distempering on surfaces of walls using mechanical spray machine/method by the authorised applicator of the manufacturer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer using mechanical spray machine/method by the authorised applicator of the manufacturer complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks of capacity exc 250 and n exc 500 ltrs and removal to contractor's store yard complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge in SSR Part I.

Dismantling water tanks of capacity exc 500 and n exc 1000 ltrs and removal to contractor's store yard complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge in SSR Part I

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removing to store complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 15 mm bore steel water tubing galvanised 15mm bore, medium grade fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removing to store complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 20mm bore steel water tubing galvanised, medium grade fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs 15 mm Brass CP central hole basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs 15 mm Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F for 15 mm bore concealed type chromium plated Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring, joints, laid in trenches or in floors or fixed to wall complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring, joints, laid in trenches or in floors or fixed to wall complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 15 mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 15 mm bore chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 15 mm bore chromium plated Stop angle valves, cast copper alloy screwed pressure, with crutch of butterfly handle,long shank and cup, screwed both ends for iron pipe for unions and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Brass chromium plated shower rose 125mm size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in polythene connection of low density polyethylene (LDPE) pipes of pressure rating 2.5 Kgf/Sqcm, 45cm long with and including two brass union couplings, heavy duty, suitable for 15mm bore pipe, one on each end for connecting polyethylene pipe to GI pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair brass chromium plated tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair vitreous China squatting pan, `Orissa' pattern, size 580 x440 mm white, with integral foot rests including provision of cement concrete bedding complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Vitreous China wash basin, white, flat back, size 550x400mm , including cutting for and pinning in ends of brackets , including 32 mm dia CP waste waste fitting and PVC waste pipe of required length complete all as specified and directed by Engineer-in-Charge.

Dismantling of stone slab and tiles of any description or thickness in floors, approns etc laid, bedded and pointed in any mortar and removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Material and labour for granite tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types including 20 mm thick bedding layer in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material and labour for granite stone tiles dado 20mm thick machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing of mirror finish type including 15 mm thick screed in CM 1 :4 on brick or concrete surface complete all as specified and directed by Engineer-in-Charge.

Material and labour for machine cut Kota stone slabs flooring 18 to 22 mm thick over 20 mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Material and labour for 18 to 22 mm thick machine cut Kota stone slabs in riser of steps, skirting, dado and pillar laid over 10 mm thick cement screed bed in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair sinks with drainage board made of stainless steel sheet 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth or wall tilling including cement mortat bedding (but not backaing coat) removing serviceable tiles to store & rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Material and labour for Glazed ceramic coloured tiles in vertical surface 350x250mmx7mm/450X350X7mm/450x300x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cm 1:4 on brick or concrete surfaces of wall to receive vertical tiles complete all as specified and directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic dark tiles of size 7-8 mm thick area of each tiles exceeding 0.11 Sqm bur not exc 0.18 Sqm (400x400mm) as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement with pigment to match the shade of tiles over and including 20 mm thick screed bed in cm 1:6 complete all as specified and directed by Engineer-in-Charge.

Demolition of PCC cement concrete above ground floor and paving n.exc 15 cm thick (below or above ground level) un reinforced complete all as specified and directed by Engineer-in-Charge.

Material and labour for 100 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in pavement/plinth protection finished even and fair complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:4:8 type D-2 (40mm graded stone aggregate ) for sub base 75mm thick complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified Ceramic tiles 10mm thick Dark shade (Square/ rectangular) polished, area of each tiles n. exc 0.36 SQm in floors etc,, set and jointed in neat cement slurry and pointed in shite or coloured cement to match over and including 20 mm thick screed bed in cm 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per serial item No 64 above but in vertical surface such as skirting, dado and risers including 10 mm thick rendering in cm 1:4 on brick or concrete surfaces of wall to receive vertical tiles complete all as specified and directed by Engineer-in-Charge.

S&F 75mm size brass handles, cast type polished bright complete all as specified and directed by Engineer-in-Charge.

S&F magnatic catch for wooden cabinate shutters complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantling as in fillets, rails, posts, rafters, purlins, etc under 40 sq.cm in section of framed work complete all as specified and directed by Engineer-in-Charge.

M&L second class soft-wood as in scantlings of timber framed and fixed wrought complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class HW plain fillet n exc 3 sqcm square rectangular or triangular in section clean sawn secured with nails or brads complete all as specified and directed by Engineer-in-Charge.

Material and labour for 12mm thick PVC Prelaminated board, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work and fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Material and labour for 18mm thick PVC Prelaminated , board, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work and fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs continuous (piano) hinges mild steel bright finish or electrogalvanised 30mm flaps complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs Harrison rails 25 mm dia mild steel chromium plated curtain rail fixing with brackets stops complete all as specified and directed by Engineer-in-Charge.

M&L for Complete removal of existing treatment from walls, fins, chajja etc shall include brooming down or steel wire brushing, scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots and removing debris/ malba to low lying area out side of MOD land and applying 3 to 5 mm thick a layer of Birla white wall care water proof putty on scrapped/uneven surfaces to match with the existing surfaces before application of primer/distemper and applying two coats of oil bound distemper over a coat of primer using mechanical spray machine/method by the authorised applicator of the manufacturer ccomplete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of old treated plastered surfaces of ceiling by brooming down or steel wire brushing scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots removing dust, dirt and all loose scales of existing treatment and applying one coat of oil bound distemper on ceiling using mechanical spray machine/method by the authorised applicator of the manufacturer complete all as specified and directed by Engineer-in-Charge.

M&L for coloured Chequered cement concrete tiles 300x300x25 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors over and including screed bed 20 mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for 60 mm thick precast cement concrete coloured interlocking tiles of grade M-35 any shape and size confirming to IS 15658-2006 with grey cement and pigment in floors / pavements incl 30 mm thick sand cushioning complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminium point wiring (light, Socket or power) complete including fittings and fixtures such as switches, ceiling roses pendents, regulators, sockets etc for taking credit to be measured separetly including making good the disturbed portion/surface complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with colour coding multistranded copper conductor cable, PVC insulated and unsheathed size 1.5 sqmm with PVC concealed Conduit ( dia not les than 25 mm) with fixing accessories for one light /fan/bell point controlled by one switch with pressed steel concealed terminal boxes covered with 3mm thick laminated sheet incl. contineous earth wire of PVC insulated unsheathed multi stranded copper conductor cable size 1.5 Sqmm for earth wire connected to common earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 80 above but for one 3/5 pin socket 5 Amp on same board, with 1.5sqmm wire with 1.5sqmm earth wire complete all as specified and directed by Engineer-in-Charge.

All as per item No 80 above but for one 3/5 pin socket 5 Amp on independent board with 2.5 sqmmwire with 2.5 sqmm earth wire complete all as specified and directed by Engineer-in-Charge.

All as per item No 80 above but for 3 pins socket outlet 15 Amps independent with 4.0 sq mm incl contineous earthing with multistandred copper conductor PVC insulated unsheathed size 4.0 Sq mm complete all as specified and directed by Engineer-in-Charge. Note:- (For item 02 to 05 ) Cost making good disturbed surface below existing point wiring taken out vide item No 02 and cutting chases and making good of disturbed surfaces by cement & sand mortar (1:3) and surface finish as per adjustment surface conduit and all accessories as required for concealed point wiring vide item No 02 to 05 as applicable shall be deemed to be included in the unit rate quoted against these items.

S&F switch piano flush type 5 Amps, single pole one way 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F socket 3/ 5 pins, 6 Amp, flush type piano (multi purpose) 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F Socket 15 Amps flush type,3/ 6 Pin, 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F switch 15 Amps flush type 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F Ding Dong door bell 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F Bell push flush type 5 Amps, single pole one way 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F ceiling rose, PVC / Polycarbonate isolated body ,surface backlite, 65x50mm, three terminals, 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F stepped type electronic fan regulator flush type 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F Batten holder PVC/Polycarbonate base / back suitable for LED lamp. 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F LED Bulbs 9/10W B-22 Pin type 230 Volts , AC complete all as specified and directed by Engineer-in-Charge.

S&F single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole 20 amps MCB complete all as specified and directed by Engineer-in-Charge.

S&F LED tube light fittings 20W (4 feet) wall mounted LED batten extruded PVC heat sink provided for efficient heat dissipation & integrated electronic driver optics diffused complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings complete all as specified and directed by Engineer-in-Charge.

S&F LED 6000K (2’ feet), 10W Decorative LED lighting fixture with extruded PVC . heat sink, environmental friendly, energy efficient ready to use pack, complete and including taking down existing fittings complete all as specified and directed by Engineer-in-Charge.

S&F LED bulkhead luminaire 10W decorative type as per sample complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings complete all as specified and directed by Engineer-in-Charge.

S&F LED building secuity light 25 watt made up of pressure die cast aluminium housing with mid power LED as lightening source and PC cover having top opening inbuilt LED driver with IP66 protection and impact resistance of IK-07 complete including GI bracket with nut bolts, washers etc including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings complete all as specified and directed by Engineer-in-Charge.

M&L for submain wiring with 2X6.0 SQMM+1X6.0SQMM Earth Wire single core PVC insulated FR sheathed copper cable connecting to common earth dolly in and including heavy duty PVC concealed Conduit and dismantling and taking down existing unserviceable wiring, all accessories complete all as specified and directed by Engineer-in-Charge.

S & F in repairs single pole and neutral sheet metal enclosures for Distribution board (DB's)suitable for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail 240 V, 50 Hz supply double door SP&N DB system 12 ways complete all as specified and directed by Engineer-in-Charge.

S&F RCBOs for earth leakage,over load & short circuit protection 2 pole ,25 Amp rating, 300 mA capacity suitable for 240 Volts and including taking down existing MCB/ RCCB complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 40-63 Amps 240V incl all termnials, fitting etc. including taking down complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP 06 to 40 Amps 240V incl all termnials, fitting etc including taking down complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing of Meter box sheet metal enclosure concealed type made of metal of size 32 x 25 x 14 cm having suitable incoming and outgoing openings for cables complete all as specified and directed by Engineer-in-Charge.

M&L for Refixing carefully serviceable fans / geysers etc any type from site on completion of civil and E/& M works incl making necessary connection with suitable copper wire and testing and incl taking down complete all as specified and directed by Engineer-in-Charge.

M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick burried directly in gorund (earth pit not less than 2.25 Mtr normal ground level),and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised means of earth wire 4 mm dia with bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 15 mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover CI frame PCC 1:3:6 type C-2 all as shown in electrical plate No-3 of SSR part-I of 2009 connected to earthing test point all as specified and indicated including all earth work excavation, returning filling and disposal of surplus soil and testing on completion complete all as specified and directed by Engineer-in-Charge.

PG CONSTRUCTION AND COMPANY

VERMA CONSTRUCTION CO

High Tech Metal India

Singh Associates

RRR CONSTRUCTIONS

NAVEEN KUMAR TYAGI