SPECIAL REPAIRS TO REPLACEMENT OF ALUMINIUM SUBMAIN WIRING AND ADDN /ALTN TO CERTAIN TOILETS AT A ROAD AT MO (MB) GHATKOPAR UNDER GE (NW) BHANDUP

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises etc out side MD land complete all as specified and directed.

Demolition of brick work or stone boulder masonry,built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work and precast concrete articles and removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

Taking down chowkat or frame with shutters( without taking of shuttrs from the frame ) n.exc 1.5 sqm each complete all as specified and directed.

M&L for brick work with sub-class 'B' bricks, straight, or curved on plan to any radius as in half brick thick wall in CM 1:4 complete all as specified and directed.

M&L for special treatment for sunken portion of WCs/ Bath & toilet executed in following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris outside MD land etc Complete. Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per Manufacture's instructions. Stage 3:- Apply Dr Fixit Primeseal primer or Equivalent of STP Ltd (and allow to dry for 8 hours) all as per Manufacture's instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP (The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per Manufacturer's instructions. Stage 5:- Rendering 10mm thick in CM 1:3 mixed with Integral water proofing chemical Dr Fixit Pidicrete URP or plaster seal of STP Ltd all as per Manufacture's instructions. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP all as per Manufacture's instruction. Stage 7:- Making holes in wall and fixing 600mm long 40mm dia medium grade GI spout for draining the surplus water if any Stage 8:- Carry out ponding test for 48 hours to ensure water tightness of repaired sunken portion.water tightness of repaired sunken portion and filling of sunken portion for cement concrete Type E2 1:5:10 using 40 mm graded aggregate as in lean concrete complete all as specified and directed. Note :- (a) Only plan area shall be measured and accorded for payment under this item. (b) Depth of sunken portion of WC's/Baths shall be upto 35cm, which is to be taken into account while quoting the rate against this item. (c) Rate quoted by Contractor shall be deemed to be included for all the horizontal and verticale treated surfaces of sunken portions of WC & Bath.

M&L for Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exc 0.06 sqm n exc 0.11 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 laying floor finished complete all as specified and directed. Notes: while fixing tiles, joint width between two tiles shall be maintained using tile spacers and filling the tile joints with three component epoxy resin based tile joint filler complete as per manufacturers instructions.

M&L for glazed ceramic coloured tiles 450x300mmx7mm thick in vertical surfaces such as skirting/dado and risers to steps and including over 10mm thick rendering in CM 1:3 on fair faces of brick/concrete surfaces as in backing coat for tiles. etc, all as specified and directed.

M&L for reinforced cement concrete type B1, 1:2:4 20 mm aggregate for Slabs supported on walls, beams and columns in floors deck slabs and in shelves etc complete all as specified and directed.

M &L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) with rough finished surface complete all as specified and directed.

M & L for TMT steel bars 10 mm dia and over, cut to n length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or rescuring with clips quality confirming complete all as specified and directed.

M&L for 18-20mm thick granite (of any type) work table rubbed and polished as in jambs, pillars, door and windows-cill, cooking platform, jambs, wash hand basin platform and the like in CM 1:4 including pointing in white/coloured cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting of oval shape for fixing of counter sunk wash hand basin etc over and including 10mm thick rendering/screed in CM 1:4 on fair faces of brick/ concrete surfaces complete all as specified and directed.

M&L for 25 mm thick green marble (table rubbed, and polished) in steps, jambs, pillars, windows-cill, cooking platform , jambs, urinal partition,wash basin platform and like in cement mortar 1:4 including pointing in white / coloured cement 1:2 using marble dust with admixture of pigment to match including one side full round edging including backing coat of 10 mm thick in CM 1:3 etc complete all as specified and directed.

M&L for rounding to edges of stone slab one edge , such as in steps , cooking paltforms , and similar situations complete all as specified and directed.

S&F white oval counter top wash basin of size 56 x 41cm including waste coupling complete all as specified.

S&F aluminium section in doors/windows/ventilators ,kitchen cupboards, built n almirah doors any type, powder coated in approved colour (Thickness of powder coating not less than 50 micron), aluminium section (medium weight of series 'B') or section as directed by Engineer-in-Charge, cut to size, jointed together with cadmium plated steel screws including rubber beading or gasket for aluminium sections for fixing glass/XPM jali or for fixing bakelite sheet and all necessary fittings complete, screws, plugs for fixing screws, etc all as specified and directed Notes : (i) Weight of aluminium sections shall only be measured. (ii) The supply only rate of bakelite sheet glass pane,wire mesh and rubber beading or gasket will be measured separately.

Supply only 4mm thick figured glass/pin headed type ordinary quality fixed in aluminium ventilator n exc 0.50 Sqm each pane all as specified & as directed.

S&F aluminum anodised grill DG- 202 ( 10 mm x 7.5mm ) of Deco grill or equivalent fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick of approved make all as specified and directed. Note :(i) Minimum thickness of anodizing shall be 15 microns.

Supply only Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples fixed in aluminium windows/wooden doors complete all as specified and directed.

S&F solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm wood grain printed PVC sheet reinforced with M.S square tube and edges will be painted to match with printed sheet supplying & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails . MS frame shall be covered with heat moulded palin colour PVC 'C" channel having a PVc sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail , lock rail & bottom rail on either side &5 mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 degree ) used instead of exposed portion of PVC sheet beading complete all as specified and directed.

S/F stainless steel butt hinges 125mm size medium wt coIled rolled complete all as specified and directed.

S&F anodised aluminium extruded handles 150 mm size complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section 200 mm size complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt 250 mm long with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F brass chromium plated towel rail 20mm dia 'D' type 600mm long between flanges, of with and including chromium plated brass screws etc complete all as specified and directed.

S&F in repairs wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gm) complete all as specified and directed.

S&F in repairs Vitreous china urinals, half stall type (back or corner wall type), complete including providing and fixing plugs , bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws , pointing around urinal back in cement; fixing automaticflushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F Health faucet with 1.5mtr tube & hook complete all as specified and directed.

S&F in repair CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&Fin repair Soap dish, Stainless steel fancy type approx size 160x160x90mm complete all as specified and directed.

S&F Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.

S & F in repairs vitrious China pedestal pattern WC incl PVC seat cover (White) etc complete all as specified and directed.

S & F in repairs vitreous China squatting pan, white, Orissa pattern pan of size 580 mm x 440 mm of standard quality with integral foot rests and including 'P' trap or 'S' Trap complete including connection to trap and to flushing pipe, anti syphonic pipe complete all as specified and directed.

S & F in repair PVC low level flushing cistern 10 Ltr capacity incl float valve and flush pipe complete all as specified and directed.

S&F in repairs grating doom 100m dia of PTMT (Minimum Wt 25 gms) complete all as specified and directed.

S&F in repairs PVC inlet connections 45 cm long, 15 mm bore with PTMT nuts complete all as specified and directed.

S&F SWR bends 110 mm dia with access door complete all as specified and directed.

S&F PVC SWR 110 mm dia single (Single Y) equal of unequal complete all as specified and directed.

S&F PVC SWR 75 mm dia single (Single T) equal of unequal complete all as specified and directed.

S&F in repairs 50mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Dismantling cast iron of any description etc complete all as specified and directed

S&F 75mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc complete all as specifed and directed.

S&F 110mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc complete all as specifed and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 25mm complete all as specified and directed.

S&F CPVC pipe 150 mm bore SDR 11and plain CPVC SDR 11 fittings fixed complete to walls, ceilings or in floors etc, complete all as specified and directed.

All as per item No 48 above but 20 mm bore etc, complete all as specified and directed.

All as per item No 48 above but 25 mm bore etc, complete all as specified and directed.

S&F in repairs CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and complete all as specified and directed.

S&F for 20mm bore sink cock swan neck (wall mountinstallation) type with chrome finish complete all as spd and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Chipping, removing carefully loose/damaged concrete including plastering from surfaces of RCC members, in any location by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land complete all as specified and directed. Note : 1) Hard concrete shall not be removed by force

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for carry out application of ‘Bi-polar migratory corrosion inhibitor' [Make : M/s. Krishna Conchem (EPCO KP-100) / BASF (MasterProtect®8000Cl)/ Dr. Fixit ] on RCC surfaces, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for Anticorrosive Treatment to Reinforcement using IPNET-RB of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed . Note :- Mode of measurement: superficial area of concrete will be measured.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar / concrete to ensure bond between old concrete & new concrete/ new mortar by brush application, complete all as specified and directed.

M&L for building up the profile of structural members using polymer modified mortar from M/s. Krishna Conchem (Molith PMM) OR Polymer mortar HB of Dr Fixit, BASF while the bonding agent is still tacking upto 20mm thickness, including levelling, profiling etc, complete all as specified and directed.

Taking down cement plaster of any description on walls including raking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

M&L for plastering in CM 1:6, 10 mm thick on walls finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for plastering in CM 1:3 , 5mm thick on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work in CM 1:6 and 5mm thick in CM 1:4 including water proofing compound, finishing even and smooth without using extra cement (WPC shall be measured and paid separately) complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and thereafter applying two coat of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed

M&L for preparation of old decorated surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and thereafter applying with roller Two coat of oil bound distemper over a coat of primer complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying Two coat of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for two coats of antifungal paint over a coat of exterior primer on newly prepared plastered external surfaces and including scaffoldings and cradle including hoisting and lowering as required with bracing, support complete all as specified and directed.

S&F in repairs 500 ltrs Rotational mould polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in ssr part-I complete all as specified and directed.

S&F Ball brass valves,high pressure, with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Taking down unserviceable exiting submain wiring any size complete all as specified and directed.

M&L for submain wiring in and including PVC conduit having thickness 1.8 mm, 25 mm dia with two run of PVC insulated, sheathed multistranded copper conductor of 10 sqmm(FRLSH) and one run of PVC insulated, sheathed multistranded copper conductor 10 sqmm (green in color) for earth continuity conductor and connected to common earth dolly with thimble etc, cutting chiseling for concealed piping and making good the disturbed surface area white wash/colour wash to matching with existing colour complete all as specified and directed.. (Note: Two run of 10 sqmm plus one run 10 sqmm of earth wire will be measured as 1RM) including dismantling of existing unserviceable submain wiring all as specified and directed. Note: colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

M&L for submain wiring in and including PVC conduit having thickness 1.8 mm, 25 mm dia with two run of PVC insulated, sheathed multistranded copper conductor of 6 sqmm(FRLSH) and one run of PVC insulated, sheathed multistranded copper conductor 6 sqmm (green in color) for earth continuity conductor and connected to common earth dolly with thimble etc, cutting chiseling for concealed piping and making good the disturbed surface area white wash/colour wash to matching with existing colour complete all as specified and directed.. (Note: Two run of 6 sqmm plus one run 6 sqmm of earth wire will be measured as 1RM) including dismantling of existing unserviceable submain wiring all as specified and directed. Note: colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

Supply installation, testing and commissioning of FAST ELECTRODE maintenance free Chemical Earthing of Dual Pipe Technology, each of 3 Meter long with Outer Pipe Diameter of 88mm (galvanised for 80-120 micron and wall thickness 1.80mm) and Inner Pipe diameter 48mm (galvanised for 80-120 micron and wall thickness 2.60mm). There shall be terminal of size 75 x 5.20mm for connection with two holes of 14mm diameter. FAST ELECTRODE shall be duly filled with the highly conductive, Non Magnetic, Non Corrosive material and duly sealed at both ends with lead terminal of 75x5.2mm at top. The ELECTRODE shall be of 'make' having approval of CPRI (Central Power Research Institute), Govt of India for a minimum short circuit current of 42 KArms for 1 Second with initial pick of 88.2 KA. The FAST ELECTRODE Earth Enhancing Compound (minimum 25Kg) shall be pored on alround the electrode. The chemical compound to be used shall be as per the manufacturer's instructions of 'Electrode' and as also certified by any BIB (Bureau of Indian Standards) accredited laboratory.Electrode connected to GI earth strip 32 x 6mm by mean of bolts, nuts, check nuts and washer of stainless steel all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including PCC pit and CI cover etc GI protection pipe of suitable size including testing on completion all as specified and directed.Make : Fast Electrode, U-Protec Earthing, Shivangi Engineering Works or equivalent as approved by the GE. Notes:- (i) The contractor shall procure the above materials either directly from the manufacturer(s) or their authorised dealers only and shall produce the original purchase vouchers alongwith original manufacturer's test certificates and other authenticated documents in compliance of the provisions as mentioned in the above item. Also all the requisite testing as specified above, in relevant IS and as directed by the GE shall be got done by the contractor. Cost of all the above elements shall be deemed to be included in the contractor's quoted rates. (ii) Any additional quantity of Earth Enhancing Compound in case required to obtain the desired results, the same also be provided by the contractor without any additional cost to the Govt. and quoted rates of above item shall be deemed to include the above element also. (iii) Necessary earth strip to connect equipment shall also provided by the contractor. (iv) Copper strip 25 mmx3mm upto 7.5 RM including above quoted rates.

Deduct Credit for Demolished/ Dismantled material Rs. (-) 155420.00 (Minus) as listed in Schedule of Credit Note1: Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum' Note 2:- The tenderer must keep in mind when quoting rates against items out in multiple store house having height 4 mts to 7 mts. Necessary scaffolding and saftey measures required during execution of work are including in this items.

R J ENTERPRISES

M/s Mukesh Engineers

Joy builders