Improvement works arresting roof leakage and allied works for Bhavanisagar sub division office building at Bhavanisagar 110 KVSS premises.

Dismantling the damaged brick parapet wall including cost of all materials, leads, lifts labour charges and dispose debris away from site etc., complete as per the direction of site Engineer incharge

Dismantling the damaged pressed tiles and weathering course without damage to the roof slab including cost of all materials, leads, lifts labour charges and dispose debris away from site etc., complete as per the direction of site Engineer incharge.

Brick work in CM 1:5 using IInd class chamber burnt bricks (230x110x70mm), OPC 53 grade cement (DALMIA / ULTRATECH / RAMCO), M sand approved quarry for basement and super structure including cost of all materials, scaffolding, labour charges, curing, lead, lift, T&P, etc., complete as directed by the Engineer in charge.

Plastering in CM 1:5, 12mm thick using OPC 53 grade cement (DALMIA/ ULTRATECH/RAMCO),P sand approved quarry for all ceiling surfaces, Sunshades, Lofts, etc., including cost of all materials, scaffolding charges, labour charges, curing, lead, lift, T&P etc., complete as directed by the Engineer in charge.

Providing P.C.C.1:1.5:3 using OPC 53 grade cement (DALMIA / ULTRATECH / RAMCO), M sand, 6mm to 10mm HBG metal (Approved quarry) including cost of all materials, labour charges, curing, T&P, lead, lift etc., complete as directed by the Engineer in charge.

Plastering in CM 1:3, 12mm thick using OPC 53 grade cement (DALMIA/ ULTRATECH/RAMCO),P sand approved quarry for all ceiling surfaces, Sunshades, Lofts, etc., including cost of all materials, scaffolding charges, labour charges, curing, lead, lift, T&P etc., complete as directed by the Engineer incharge.

Manufacturing supplying and fixing of Fully Panelled single leaf steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames, stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. 3nos. of Steel Parliament Hinges of Size 125mm x 150mm to be provided. 6nos. of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 3 nos, one at the top, one at lock rail(Inner) and the other at the bottom are provided 1no. Aldrop is provided at lock rail section in the door 2 Nos of 200mm handle are to be provided. One rotating locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given painting two coats ready mixed enamel paint with One coat of primer approved quality and colour. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete complying with standard specification and as directed by the Engineer incharge

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - Each., aluminium tower bolt 200x12mm - 1No., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete complying with standard specification and as directed by the Engineer incharge. All the Alu. Section are to be anodised with matt finish under electrically controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.

Supplying , fabricating and fixing in position Aluminium Anodised natural colour mat finish Two track sliding window in all floors with Aluminium sections of outer Frame bottom 62x37mmx1.50mm at 1.218 kg/m,the Side & Top 62x31.50x1.50mm at 0.778 kg/m,Shutter Top 40x18x1.5 at 0.38 kg/m,Bottom 40x18x1.5 at 0.38kg/m, Side Vertical 40x18x1.50mm at 0.493 kg/m, Vertical locking section 40x29x1.5mm at 0.632 kg/m, with necessary accessories such as rubber beadings, special hinges, lock, handle including supplying and fixing 4mm thick plain glass including cost of all materials, labours, power consumption required for fabrication , drilling holes in RCC colunm, slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing etc... complete complying with standard specification and as directed by the Engineer incharge.The aluminium sections are to be anodised with matt finish under electrically controlled in accordance with IS 1868 / 1962 for an average anodic film thickness 15 microns etc., complete.

Supplying and fixing PVC panelled door shutters hollow type with PVC frames including cost of necessary aluminium hinges and other furniture fittings, leads, lifts, labour charges etc, complete as per specification.

White washing two coats with freshly burnt white shell lime for ceilings including cost of lime, fevicol typ gum, brushes, scaffolding charges, scrapping the old surface, leads, lifts charges labour charges etc complete.

Interior and Exterior wall colour washing with two coats using ready mixed Weather Proof Emulsion (First quality - Asian paint ultima or its equivalent) of approved quality over a coat of exterior emulsion water based primer in surfaces and with two coats of wall putty ,including clean removal of dirt, cost of all materials, scaffolding, labour, lead, lift etc. ,complete as directed by the Engineer in charge.

Painting two coats of damp proof paint over one coat of primer of first class quality over roof top including cost of all materials, scrapping the old surface, labour lead, lift, scaffolding etc., complete.

Supplying and fixing of structural Steel for ladder and window grills including cost of all materials, fabrication charges, painting with two coats of enamel paint over one coat of primer, labour charges, lead, lift and making good of damaged portion etc complete

Supplying and Providing PVC 4 layer tank (SINTEX/ASHIRVAD/SUPREME) 1000Lit of approved quality and make including necessary inlet, outlet, over flow and drain line fixing accessories / fitting, cost of all materials, labour charges for fixing, lead, lift etc.,complete as directed by the Engineer in charge.

Supply and laying of PVC pipe 110mm dia (4kg/cm²) of (FINOLEX / ASTRAL / SUPREME) of approved make and quality with ISI monogram for downfall pipes and including cost of all materials, all specials such as Tees, Elbow, shoes, Special clamps, bends and screws, gratings etc., making holes in masonry / concrete, restoring the disturbed area to original condition, making water tight jointing with no leakage, labour, scaffolding, lead, lift etc., complete as directed by the Engineer in charge.

Supply and laying of PVC pipe 25mm dia (10kg/cm²) of (FINOLEX / ASTRAL / SUPREME) approved make and quality with ISI monogram as directed by the Engineer in charge for downfall pipes including cost of all materials, all specials such as Tees, Elbow, shoes, Special clamps, bends and screws, gratings etc., making holes in masonry/concrete, restoring the disturbed area to original condition, making water tight jointing with no leakage, labour, scaffolding, lead, lift etc., complete.

Supplying and fixing of 40mm dia PVC pipe 10 Kg/cm2 (Shell thickness 2 to 3 mm) of appd. Quality for water supply line from water sump and delivery line including cost of pipe, bend, elbow, labour for cutting, threading, and fixing in position, testing all materials, solution, lead, lift etc., complete.

Supplying and fixing 25mm dia Heavy Gate valve (LEADER/ZOLOTO) of approved quality including cost of all materials, labour charges for fixing, lead, lift etc., complete as directed by the Engineer in charge.

Supplying and fixing 40mm dia Heavy Gate valve (LEADER/ZOLOTO) of approved quality including cost of all materials, labour charges for fixing, lead, lift etc.,complete as directed by the Engineer in charge.

Supplying and fixing of 15mm dia CP coated bib cock of long bady / short bady (Heavy Duty) (Parryware / Plato or its equivalent) as directed by the Engineer in charge including cost of all materials, labour charges for fixing, lead, lift, etc., complete.

Supplying and fixing in position White Glazed Model Floor Mounted European Water Closet of size 460x380mm of best quality and approved make with 100mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flpped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as 15mmbras connections, 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re- doing the dismantled masonry to original condition. Floor Fitting including cost of all materials, labour charges, lead, lift, curing etc., complete complying with standard specifications.

Supplying and fixing of wash basin of size 550 x 400 mm of approved quality neycer / parrys ISI including cost of wash basin with pedastal cock fixing using rag bolt and nut 15mm dia pvc connecting hose and outlet using 50mm dia pvc waste water pipe for outlet cp angle valve with all accessories including cost of all materials, labour, lead, lift, etc., complete as directed by the Engineer in charge.

Wiring with 2x1.50 sq.mm PVC insulated unsheathed FRLS copper cable of 1100V grade in suitable PVC rigid pipe in wall and ceiling with PVC accessories and with T.W suitable box in flush with wall with 5A FT switch covered with hylem sheet of 3mm thick with painting of suitable colour continuous earth wire connection of 1.5 sq.mm copper wire for open PVC light point and fan point.

Wiring with 2x1.5sqmm PVC insulated SC unsheathed FRLS Copper Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box in flush with wall with 3 mm thick Hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with painting suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for open PVC plug point.

Wiring with 2x4 sqmm PVC insulated SC unsheathed FRLS Copper Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box in flush with wall with 3 mm thick Hylem sheet cover for 15A 3 pin flush type non interlocking wall socket with 15A flushtype switch with painting suitable colour with continuous earth wire connection of 4 sq.mm copper wire for open PVC plug point.

Supply and fixing of 20W4 Feet LED Fitting of Higher end (Philips/Havells or equivalent make) as approved by the engineer incharge at site with round blocks on wall or ceiling with PVC unsheathed copper lead from terminals to the fittings including cost of all materials such as cables, pipes, etc., complete as directed by the Engineer in charge.

Supplying and fixing of 1200mm (48”) sweap BLDC ceiling fan with 300mm down rod with appd best quality make of standard specification with electronic regulators and switch including cost of all materials, labour, fixing, charges as per standard specification, etc., complete.

Supplying and fixing of 30W LED streetlight fitting with LED with 25mm dia GI pipe (class B) with 1 no. 25mm GI bend complete on the existing post/on wall with PVC unsheathed copper leads with MS clamp with painting including cost of all materials, lead, lift, fixing charges etc., complete.( Philips /Crompton make ).

Supplying and fixing of 8 way single pole and neutral MCB sheet steel enclosure Distribution board with Double door ( Metal ) 1 No. 32 Amps DP MCB as incoming and 6 Nos. 6 Amps to 32 Amps SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark