Construction of new embankment on both banks of river Kakodunga from Mohbandha PWD Road to NH37

Amount

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting p g to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (i) Govt Land

Haulage excluding Loading & Unloading A. Haulage of materials by tipper excluding cost of loading, unloading and stacking. Case-II: Unsurfaced Gravel Road (2 km @ Rs 18.50)

Furnishing and laying of the live sods of perennial turf forming grass on embankment slope, verges or other locations shown on the drawing or as directed by the Engineer including preparation of ground, fetching of sods and watering as per Technical Specification Clause 309.

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. In marshy soil A (II) Manual means (Depth up to 3m)(With dewatering)

Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork. I. Without Plasticiser A. P.C.C grade M 15

Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork. I. Without Plasticiser C. RCC Grade M20 (Case I) Using concrete mixer

Supplying, fitting and placing MS Bar (Fe-500 ) reinforcement bar From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL) in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

Providing and laying boulders apron on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification. A. Boulder laid dry without wire crates

Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size toeards the wall and provided over the entire surfaces behind the abutement, wing wall and return wall to the full height compacted to firm condition complete as per drawing and technical specification.

Cement concrete blocks (size 0.5 x 0.5 x 0.5 m) (Providing and laying of apron with cement concrete blocks of size 0.5x0.5x0.5 m cast in-situ and made with nominal mix of M-15 grade cement concrete with a minimum cement content of 250 kg/cum as per IRC: 21-2000.)

Construction of whole bamboo single palisading with matured bhaluka bamboo posts 7.5cm to 10 cm dia.,15 cm clear apart 1.50m to 1.80m above ground and 1.00m to 1.20m below ground with bhaluka bamboo inclined struts placed at 1.5m a part tied with three rows of horizontal half jati bamboo kamies etc. complete as directed. (Using Bhaluka Bamboo at the rate of 10.14 nos/ Rm & Jati Bamboo at the rate of 2.40 nos / Rm)

Serviceable empty cement bags

Labour charge for laying and pitching earth filled cement bags including excavation and borrowing earth, breaking clods, filling in bags and supplying and stitching the mouth with jute sutli, etc. complete as directed. (cement bags will be supplied by the department free of cost). For borrowing earth from a distance beyond 30m. & up to 60m.

Supply of Ordinary Labour for miscellaneous works.

Dewatering by 5 H.P. water pump including supply of necessary fuel, engine oil and pump operator etc complete..

M.S. plate for skin plate of shutter of 10mm thick

M.S. channel for frame, horizontalgirders and vertical stiffners

M.S. flat for Rubber seal, size

J-Type rubber seal, 125mm

J-Type rubber seal corner, 125mm

M.S. washer

M.S. Nuts and Bolts 6mm dia x 37 mm length

Rubber bostic, 100 ml packet

C.I. Guide roller

Guide roller M.S. bracket

Guide roller M.S. shaft

M.S. guide channel

Fabricated G.I. Pipe 25mm for separator bolt

M.S. separator stud 25mm dia x 75mm length

M.S. screw shaft (60mm dia)

M.S. screw shaft pin, 19mm dia

Fabricated M.S. base plate, 600x600x10 mm

Fabricated M.S. tool plate, 300x300x10 mm

Fabricated M.S. lock plate, 300x300x6 mm

Fabricated M.S. tool post made of 75x75x6 mm angle

C.I. Boss 200mm (L) x 150mm (D)

H.D. thrust bearing 50mm dia

Lock plate separator made of M.S. pipe 15mm dia x 50mm

C.I. Grove pulley 250mm dia

C.I. Grove pulley 200mm dia

Pulley Pin

Fabricated pulley stand for fixing 250mm dia pulley

Fabricated pulley stand for fixing 200mm dia pulley

Steel wire rope 16mm dia (Tested quality)

U Clamp for 16mm dia wire rope

G.I. pipe 25mm for handle of Boss

C.I. Counter weight

Counter weight bolt 25mm x 600mm length

Counter weight fixing nut and bolt

G.I. thimble

M.S. Nuts and Bolts for tool post, lock plate and washer

L Bracket made of 10mm M.S. Plate for screw shaft

M.S. channel 200 x 75 mm for bottom channel

M.S. plate 6mm thick for anchoring

2nd stage concreting, Civil works for guide channel and bottom channel installation

M.S. supporting channe 3.5 x 1.2 x 4.00 M

M.S. channel 200 x 75 mm for top channel

M.S. cross channel 100 x 50 x4.7 mm

M.S. block sheet for plateform top 4mm

M.S. for ralling post 50 x 50 x 6 mm

M.S. angle for ladder 50 x 50 x 6 mm

G.I. pipe 25mm for railling

M.S. Nuts and Bolts (Assorted size)

M.S. washer (Assorted size)

Red Oxide Metal Primer

Synthetic Enamel Paint (P/.O. Red)

G.P. Thinner

White Paint

Black Paint

Welding cable 600 Amp

Gas Hose pipe (Red)

Gas Hose pipe (Green)

Welding Holder, 600 Amp

Welding Helmet

M.S. Electrodes, 8 SWG

M.S. Electrodes, 10 SWG

Acetylene Gas Cylinder

Oxygen Gas Cylinder

Cutting torch

Acetylene Regulator

Oxygen Regulator

Welding Glass (Black)

Welding Glass (White)

Welding Mask with Handle

Welding Gloves

Welding Googles

Steel wire brush

Mobile

H.S.D. Oil

Waste cotton

W.B. Grease

Painting Brush, 3"

Emery Paper

Hacksaw blade

Washing soap

Kerosene oil

Nylon rope, 25mm dia

Transportation of materials up to the work site

Febrication and Field painting

Overhead charge and contractor's profit

Erection of equipments

Marketing cost

Temporary jigs and fixtures

Cutting cost