COMPREHENSIVE REPAIR/ MAINTENANCE OF CERTAIN BLDGS AND REPAIR TO JOINERY AND CLEANING OF OVERHEAD WATER TANKS IN NORTH SIDE OF RUNWAY AT AF STN BHISIANA

Amount

Taking down cement plaster on brick walls, concrete surface, static water tanks etc including Racking out joints hacking to key scrubbing down with water etc, complete all as specified and directed by Engineer in charge.

M&L for Rendering on concrete/ brick surfaces 15mm thick in CM 1:4 (externally) finished even and fair at height upto 10 mtr, complete all as specified and directed by Engineer in charge.

M&L for Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed with Coarse Sand and Cement in the Ratio 1:1:1 shall be applied and finish Even, complete all as specified and directed by Engineer in charge.

M&L for Preparation new plastered surface of wall, concrete surface and applying two coats of all weather exterior emulsion paints in camouflaging pattern @1.43 litre/10 sqm over and including priming coats of exterior primer of same make applied @0.9 litre/10 sqm as per new sigma pattern generated by station authority and RGB value variation from 110 to 171 by using 4 to 5 colour shades as per approved pattern at a height n.exc 25 mtr as per sample approved by GE, complete all as specified and directed by Engineer in charge. (note: the % of the colour may change without any financial effect.)

M&L for Rendering 10 mm thick in CM 1:6 on concrete/ brick wall surfaces finished surface even and smooth without using extra cement, complete all as specified and directed by Engineer in charge.

M&L for Preparation of newly plastered surfaces of walls including cornices pilasters etc and applying two coat of oil bound Distemper (OBD) over a coat of priming surface, complete all as specified and directed by Engineer in charge.

M&L for Rendering 5 mm thick in CM 1:3 on concrete surfaces finished surface even and smooth without using extra cement as in ceiling surfaces, complete all as specified and directed by Engineer in charge.

M&L for Preparation of newly plastered surface of ceiling including cornices pilasters etc.and applying three coat of white wash on ceiling, complete all as specified and directed by Engineer in charge.

M&L for 24 guage chicken wire mesh for plastering work at joints of wall & beam Rcc etc ,of 10 mm to 13 mm opening dia size, fix with nails, screws or supporting arrangement as required, complete all as specified and directed by Engineer in charge.

Demolition of brick work built in cement mortar, complete all as specified and directed by Engineer in charge.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and directed by Engineer in charge.

M&L for Brick work with sub class 'B' bricks (Except bricks) straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and directed by Engineer in charge.

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls in CM 1:4, complete all as specified and directed by Engineer in charge.

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing ) removing rubbish outside MD land, complete all as specified and directed by Engineer in charge.

M&L for Non skid ceramic tiles/ Non skid tiles coloured, area of each tile exceeding 0.11 sqm but not exceeding 0.16 sqm as per the existing tiles and size as suitable/ matching with the existing tiles in dados/ floors including set and jointed in neat cement in CM 1:6 slurry and pointed in white or coloured cement to match the colour of tile, complete all as specified and directed by Engineer in charge.

M&L for Glazed ceramic coloured tiles of size 450x300 x 6 to 7 mm thick on vertical surface such as skirting/ dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including rendering 10 mm thick cement plaster in cement mortar 1:4 finished rough to fix tiles, complete all as specified and directed by Engineer in charge.

M&L for Vitrified Ceramic tiles 10 mm thick Dark Shade/ Double tiles charged/ ultracharged (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but n. exceeding 1.0 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick cement screed bedding layer in cement mortar 1:6, complete all as specified and directed by Engineer in charge.

M&L for Vitrified Ceramic tiles 10 mm thick Dark Shade/ Double tiles charged/ ultracharged (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but n. exceeding 1.0 sqm in dado/skirting/wall etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick cement screed bedding layer in cement mortar 1:6, complete all as specified and directed by Engineer in charge.

M&L for Acid resistant tiles 15mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors/wall surface including rendering 10 mm thick cement plaster in cement mortar 1:4 finished rough to fix tiles, complete all as specified and directed by Engineer in charge.

M&L for Boring holes through glazed tile lining for pipes, etc n exc 50mm dia and making good, complete all as specified and directed by Engineer in charge.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15 cm thickness (below or above ground level), complete all as specified and directed by Engineer in charge.

M&L for Machine cut Kota stone slab flooring, 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing (granite finish) and exposed edges of Kota stone shall be rounded including 15mm thick screed bed to floor finishes in cm 1:4, complete all as specified and directed by Engineer in charge.

M&L for Granite stone 16-18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and exposed edges of granite shall be rounded including 15mm thick screed bed to floor finishes in cm 1:4, complete all as specified and directed by Engineer in charge.

M&L for 75 mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base finishing the surface even and rough to receive floor finishes, complete all as specified and directed by Engineer in charge.

M&L 40 mm thick Plain Cement Concrete 1:2:4 type B-0 (Using 12.50 mm graded stone aggregate) finishing surface as in floor/ top surface/ finish surface, complete all as specified and directed by Engineer in charge.

Demolition of cement concrete any description in any position not otherwise specifically provided, complete all as specified and directed by Engineer in charge.

M&L for Cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) as in roof kerbs, mud stops, top copping rounded PCC as in kerbs/ covet fillet, complete all as specified and directed by Engineer in charge.

M&L 50 mm thick Plain Cement Concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection finished surface even and smooth without using extra cement, complete all as specified and directed by Engineer in charge.

M&L for TMT bars 10 mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips quality confirming to Fe-410-S 0r Fe-410-O, complete all as specified and directed by Engineer in charge.

M&L for Formwork to soffits of suspended slabs rough finish flat surface such as slab resting on wall or over hang, landings and similar work, not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed by Engineer in charge.

M&L for Cement Concrete 1:2:4 type B-0 (Using 12.50 mm graded aggregates) Slabs supported on walls, beams and columns for counter shelf of WHB slabs and in shelves and the like, complete all as specified and directed by Engineer in charge.

Taking down wall panelling and similar works as specified and removing to stores, complete all as specified and directed by Engineer in charge.

M&L for PVC SHEET WALL PANELLING of solid thickness 5 mm consisting of panels of desired size stuck on inner frame work of 50mm wide strips of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cbm density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. A groove of 2mm may be left at the joint of two panels for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a U Channel at top, bottom and side edges and strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement and colour approved by GE, complete all as specified and directed by Engineer in charge. Note- Including all necessary fittings and scaffolding for heighted site)

Demolition of cup board of wooden/ PVC of box type any type and any size, complete all as specified and directed by Engineer in charge.

S&F of 18 mm thick PVC Board/sheet of Plain color fixed with screws, solvent cement/ adhesive to make cupboard sides top and bottom and shelves inside the cupboard complete as per specifications, complete all as specified and directed by Engineer in charge.

S&F of 18 mm thick solid PVC Board/sheet of one side Prelam/Rigidlam and other side balancing laminate colour to make cupboard Shutter/ drawer Front shutters complete as per specifications, complete all as specified and directed by Engineer in charge.

S&F of 5-6 mm thick solid pvc sheet of plain white colour fixed with screws, solvent cement/ adhesive to make kitchen cabinet back covering and pull out drawer base complete as per specifications, complete all as specified and directed by Engineer in charge.

S&F of 20mm wide & 1mm thick PVC EDGE BENDING of PVC pasted on edges with suitable adhesive, complete all as specified and directed by Engineer in charge.

S&F of of Ball bearing runners 45 mm Telescopic Channel ( 20 Inch ) full extension load capacity 50 kgs, complete all as specified and directed by Engineer in charge.

S&F of Continuous (piano) hinges, mild steel, bright finish or electro galvanised, complete all as specified and directed by Engineer in charge.

M&L for Repairs/Maintenance to Steel Gate along with fencing/wall, Oiling/ Greasing of all Moving Parts of the Gate and making Serviceable for smooth functioning , Free Movement of Gate including replacement and welding, drilling, etc. of all Minor Parts (viz Nuts, Bolts, Rods, Flat Iron, Angle Iron, Guide Rail, Ball Bearing, etc. of Steel Gate, area n. exc. 20 SQUARE METRE Each (approximately), complete all as specified and directed by Engineer in charge.

Easening of door exc 1 sqm but not exc 2.5 sqm each by making adjustment to hinges planning the sides of doors including taking down of door and refixing if required, complete all as specified and directed by Engineer in charge.

Easening of door not exc 1 Sqm each by making adjustment to hinges planning the sides of doors including taking down of door and refixing if required, complete all as specified and directed by Engineer in charge.

M&L for Repairs of PVC door shutter by making minor adjustment to hinges etc easening of shutter including taking down of shutter if required, complete all as specified and directed by Engineer in charge.

M&L for Repairs of steel gate by making minor adjustment to hinges etc easening of shutter including taking down of shutter, welding if required, complete all as specified and directed by Engineer in charge.

Fixing only resecuring of Anodised aluminium snap grid of size 605X 605 mm frame work for false ceiling part portion incl necessary fixing arrangements complete levelled with existing ceiling level, complete all as specified and directed by Engineer in charge.

S&F of 12 mm thick except perforated particle board / tiles for insulation and acoustic purpose, 600 X 600 MM size fixed with staples on snap grid as in ceiling, complete all as specified and directed by Engineer in charge.

Fixing only Gypsum Board 12mm thick of size 600x600 mm in ceiling fixed with screw or supporting arrangements on snap grid as in ceiling as per manufacturers instructions, complete all as specified and directed by Engineer in charge.

Fixing only suspended false ceiling system using chicago metallic (E grid) exposed suspended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC (High pressure steam cured) pre-primed , self embossed. textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 3- 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip) hold down clips (Wt-0.0035 Kg/clip) with Provn of light fixture, complete all as specified and directed by Engineer in charge.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame), exc 1.5 Sqm but not exc 4 sqm each, including taking out hold fasts and PCC bed block, complete all as specified and directed by Engineer in charge.

Taking down shutter of any description exc 1.0 but n exc 2.0 sqm Sqm each, complete all as specified and directed by Engineer in charge.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame), n.exc 1.5 Sqm each, including taking out hold fasts and PCC bed block, complete all as specified and directed by Engineer in charge.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing supplying & fixing in the frame at site, complete all as specified and directed by Engineer in charge.

M&L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length, complete all as specified and directed by Engineer in charge.

S&F of 30 mm thick Plain, framed, panelled shutters 2nd class hard wod (two number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engineer in charge.

S&F of 35mm thick 2nd class hard wood glazed or Skelton shutter factory made open rebated prepared to receive glass, gauge etc without sash bars edges of framing plain fitted with cut and mitered beads for securing glass etc size of member all as per clause 8.23 (a) of SSR Part-I, complete all as specified and directed by Engineer in charge.

S&F of Butt hinges 100mm size, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed by Engineer in charge.

S&F of Aluminium, anodised, barrel tower bolts 150mm long of extruded section, complete all as specified and directed by Engineer in charge.

S&F of Aluminium handles 150mm size, cast type, anodised, complete all as specified and directed by Engineer in charge.

S&F of Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed by Engineer in charge.

S&F Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor, complete all as specified and directed by Engineer in charge.

Preparation of new Surfaces of wooden, not otherwise descri-bed, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed by Engineer in charge.

S&F in repairs 125 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and directed by Engineer in charge.

S&F in repairs Aluminium alloy, anodised, 300 MM sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed by Engineer in charge.

S&f in repairs 100 mm Extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed by Engineer in charge.

S&F in repairs 200 mm long aluminium anodized barrel tower bolts of extruded section, complete all as specified and directed by Engineer in charge.

S&F in repairs 150 mm long aluminium anodized barrel tower bolts of extruded section, complete all as specified and directed by Engineer in charge.

S&F in repairs 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame, complete all as specified and directed by Engineer in charge.

S&F in repairs mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete (Helical door spring) including welding to steel chowkhats if required, complete all as specified and directed by Engineer in charge.

S&F in repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified and directed by Engineer in charge.

S&F in repairs Door closer hydraulically of aluminium extruded section body regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed by Engineer in charge.

S&F in repair 12 mm Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work fixed with screw to timber frame or shutter any thickness, complete all as specified and directed by Engineer in charge.

S&F Solar control film 25 micron reflective type (gareware sun control or equivalent) applying on glass incl. securing glass in metal frames and making good, complete all as specified and directed by Engineer in charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames glazed with putty or fixed with beads, complete all as specified and directed by Engineer in charge.

S&F of Sheet glass ordinary quality 4.0 mm thick in square not exc 0.50 Sqm each pane glazing with oil putty, clip in metal frame and wooden beading in wooden frame, complete all as specified and directed by Engineer in charge.

S&F of Sheet glass ordinary quality 4.0 mm thick in square exc 0.50 Sqm each pane glazing with oil putty, clip in metal frame and wooden beading in wooden frame, complete all as specified and directed by Engineer in charge.

All as per ser item No 75 above but 4 mm thick frosted on pane side glass pin headed type, complete all as specified and directed by Engineer in charge.

S&F in repair 15 mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule, complete all as specified and directed by Engineer in charge.

S&F in repair 20 mm bore Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule, complete all as specified and directed by Engineer in charge.

S&F Rotational moulded polythene water storage tank double layer, ISI Marked of capacity 500 litre cylindrical vertical with closed top hoisted in position complete including dismantling of existing tank of any description, capacity, complete all as specified and directed by Engineer in charge.

S&F Rotational moulded polythene water storage tank double layer, ISI Marked of capacity 1000 litre cylindrical vertical with closed top hoisted in position complete including dismantling of existing tank of any description, capacity, complete all as specified and directed by Engineer in charge.

Taking up or down steel tubing 15 mm bore and connections, including cleaning for refixing or removal to store, complete all as specified and directed by Engineer in charge.

Taking up or down steel tubing 20 mm bore and connections, including cleaning for refixing or removal to store, complete all as specified and directed by Engineer in charge.

M&L for refixing of steel old tubing 15 mm bore with necessary connection including new fittings, in new or old position in wall, ceiling and floor, complete all as specified and directed by Engineer in charge.

M&L for refixing of steel old tubing 20 mm bore with necessary connection including new fittings, in new or old position in wall, ceiling and floor, complete all as specified and directed by Engineer in charge.

S&F galvanised steel water tubes 'medium grade', 15 mm bore, with and including all GI fittings . fixed to walls, ceiling or laid in floors, complete all as specified and directed by Engineer in charge.

S&F galvanised steel water tubes 'medium grade', 20 mm bore, with and including all GI fittings . fixed to walls, ceiling or laid in floors, complete all as specified and directed by Engineer in charge.

S&F in repair tubular towel rail 600 mm long of brass chromium plated 20 mm dia D type 60 cm long fixed with two plugs (gutties) of 2nd class hard wood embedded in cement mortar 1:3 with MS screws, complete all as specified and directed by Engineer in charge.

S&F in repairs angle iron brackets for WHB & kitchen sink including making good to existing surface including taking down WHB/ Sink and refixing the same, complete all as specified and directed by Engineer in charge.

S&F for chromium plated brass WHB mixer fancy type high pressure with or without lettered hot and cold and flynuts 15 mm dia, complete all as specified and directed by Engineer in charge. ( Make : Jaquar cat part No: OPP-15011BPM design no: 276010 )

S&F in repair, bib taps, cast copper alloy, chromium plated with crutch bib cock with wall flange, screwed down, screwed for 15 mm bore, complete all as specified and directed by Engineer in charge. ( Make : Jaquar cat part No: OPP-15037PM )

S&F repair angle valve 15 mm nominal bore, brass, fancy type, chromium plated, with wall flange , handles, screwed both ends for iron pipes or for unions complete, complete all as specified and directed by Engineer in charge. ( Make : Jaguar cat part No: OPP-15053PM )

S&F 15 MM Pillar taps, cast copper alloy, with capstan heads fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed by Engineer in charge.

S&F in repair 15 MM fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engineer in charge.

S&F repair angle valves /stop valves 15 mm nominal bore, brass, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handles, screwed both ends for iron pipes or for unions complete, complete all as specified and directed by Engineer in charge.

S&F repair Glass corner shelf including CP railing, radius 300 mm complete, complete all as specified and directed by Engineer in charge.

S&F in repairs brass chromium plated grating 125 mm dia circular with centre hole/ without hole of approved make and fixing with cement mortar 1:3 on Nahani trap or floor trap, complete all as specified and directed by Engineer in charge.

S&F in repairs plastic seat cover white for water closet pedestal pattern closed patter with flat bottom fixed with mild steel chromium plated or aluminium hinging device, complete all as specified and directed by Engineer in charge.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest including CI 'P' or 'S' trap with providing lime concrete bedding and connecting to flusing cistern complete including breaking up existing damaged WC seat and connecting flush pipe etc and make good to floor, complete all as specified and directed by Engineer in charge.

S&F in repair vitreous china wash hand basin, white, flat back size 550 x 400 mm including one number brass CP waste coupling, 32 mm dia, brackets 2 numbers including cutting for and pinning in ends of brackets, complete all as specified and directed by Engineer in charge.

S&F in repair vitreous china wash hand basin oval shape , white, flat back size 550 x 380 mm including one number brass CP waste coupling, 32 mm dia, brackets 2 numbers including cutting for and to be fitted in RCC shelf with granite fixed incl making good, complete all as specified and directed by Engineer in charge.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern) white including plastic water closet sheet cover white, closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device and including mild steel chromium plated jet fixed to water closet with 15mm dia and 1.2m to 1.5m long flexible pipe, complete all as specified and directed by Engineer in charge.

S&F in repair Vitreous China urinals,half stall urinal type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long screws, pointing around urinal back in white cement, complete all as specified and directed by Engineer in charge.

S&F in repair 32 mm dia PVC waste pipe for WHB, complete all as specified and directed by Engineer in charge.

S&F in repair 50 mm dia PVC waste pipe for urinal, complete all as specified and directed by Engineer in charge.

S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings symphonic action with top push type button with inlet ball valve and float including flush pipe, ball valve, handle, bracket PVC short bend etc, complete all as specified and directed by Engineer in charge.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), complete all as specified and directed by Engineer in charge.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and directed by Engineer in charge.

Taking down eaves gutters and rainwater pipes / PVC pipe (any size or pattern, any type), including all fittings, heads, shoes, bends, swan-necks, etc. including cleaning or refixing or removal to Store, complete all as specified and directed by Engineer in charge.

S&F 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed by Engineer in charge.

S&F 110 MM PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) 75 mm bends any radius, complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) 75 mm vent cowl, complete all as specified and directed by Engineer in charge.

S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) 110 mm bends any radius, complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) 110 mm vent cowl, complete all as specified and directed by Engineer in charge.

S&F 110 mm PVC (SWR) 'P’ trap, complete all as specified and directed by Engineer in charge.

M&L for 25 mm dia mild steel pipe curtain rod , powder coated fixed with & including MS powder coated hooks/brackets and decorative finials (at both side), shade as approved by GE complete all as specified including fixing of long size rawl plugs in wall, complete all as specified and directed by Engineer in charge.

S&F polyester coloured venetian blind mounted on doors/ windows/vents with aluminium hanging channel with sliding wheel rope including all necessary fittings and fixture and taking down old drapery rod, making good surrounding area, complete all as specified and directed by Engineer in charge.

M&L for repairs to leaking bib cock, pillar cocks, Stop cock, angle valve of any description by changing the jumper valve, washers etc and making functional, ensuring proper water supply, complete all as specified and directed by Engineer in charge.

M&L for repairs to leaking low level or high level flushing cistern by adjusting the float valves, internal fittings and including removal and replacement of rubber washer in PVC siphons, leaking PVC bends/GI pipes etc, complete all as specified and directed by Engineer in charge.

M&L for removing of bushes upto 10 cm dia trunk, grass from roof top, racking out joints/pointing to brick tiles and flush pointing with 1:3 CM with water proofing compound & making good, complete all as specified and directed by Engineer in charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm (single rebate) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete including PCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) for repair of hold fasts and similar works as per specified drawings, complete all as specified and directed by Engineer in charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm (single rebate) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete including PCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) for repair of hold fasts and similar works as per specified drawings, complete all as specified and directed by Engineer in charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 50 x 125 mm (double rebate) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete including PCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) for repair of hold fasts and similar works as per specified drawings, complete all as specified and directed by Engineer in charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engineer in charge.

S&F factory made Single Extruded WPC (wood polymer composite) solid decorative type flush door shutter of size 30 mm th comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and Natural Fibers (Wood Powder /Rice Husk / Wheat Husk) and Non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N1100 (Edge), Minimum compressive strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof , water / Moisture Proof & Fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design posted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk ss screws, complete all as specified and directed by Engineer in charge. (Note : stainless steel butt hinges and necessary S S screws shall be paid separately.

S&F Factory Made 30mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Wire mesh Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. For fixing Mosquito mesh and XTN aluminium mesh combinly panel area of door except stiles and rails to be panelled with mesh with self tapping round headed screws at required distance, scres and edges covered with feathered pvc edge beading all around of mesh and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws, complete all as specified and directed by Engineer in charge.

S&F 10 mm Toughened glass as in UPVC doors/window and similar work including cutting to shape, drilling holes required. fixed in door shutter, complete all as specified and directed by Engineer in charge.

M&L powder coated Anodised aluminium frame(minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed by Engineer in charge.

M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws all complete as per architectural drawings, complete all as specified and directed by Engineer in charge.

S&F for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings, complete all as specified and directed by Engineer in charge.

S&F in repairs aluminium powder coated window/door grills, mesh size 50mm x50mm thickness 3.8mm, complete all as specified and directed by Engineer in charge.

S&F of powder coated anodised aluminium door shutters, aluminium sections weighing .55 kg/M including necessary joining cleats , glazing clips, rubber neoprene packing, handles 2 Nos in each door, 3 Nos hinges, 2 Nos tower bolts, anodised aluminium snap beading screws etc, complete all as specified and directed by Engineer in charge.

M&L for Powder coated Aluminium windows of three tracks outer frame top, side sections, bottom frame (track) with guide track of size 92.5x31x1.50mm with sliding window shutters two nos with glass and one no with wire mesh (total 3 nos shutter) frame top and side bottom section with wheel track and inner locking section of size 40X18X1.5mm including glass 4 mm thick and aluminium wire cloth, 0.45mm nominal dia wire and average width of aperture 1.40mm, complete all as specified and directed by Engineer in charge.

S&F anodised aluminium window and ventilator shutters, side hung type with out sash bars, aluminium section weighing 0.55kg/m incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100 mm long (2 No) suitable handle (1 No) with powder coating of any colour (thickness of powder coating not less than 50 micron), complete all as specified and directed by Engineer in charge.

M&L 12 mm thick both sides prelaminated Particle board, exterior grade, fixed with screws to frame work in cup board shutters, partitions, shelves etc, complete all as specified and directed by Engineer in charge.

S&F 5.5 mm thick tinted glass ordinary quality and glazing with fixing arrangement as specified or directed in aluminium shutter or upvc shutters (supplied along with shutter) exc 0.50 sqm each, complete all as specified and directed by Engineer in charge.

S&F sheet glass ordinary quality 4.8 mm thick in square exc 0.50 Sqm each pane glazing fixing arrangement as specified or directed in aluminium shutter or upvc shutters, complete all as specified and directed by Engineer in charge.

S&F sheet glass ordinary quality 4.8 mm thick in square n. exc 0.50 Sqm each pane glazing fixing arrangement as specified or directed in aluminium shutter or upvc shutters, complete all as specified and directed by Engineer in charge.

S&F in repairs mortise lock vertical type size 100 mm, 4 levers for Aluminium doors of MS complete with handle as per sample kept in GE office make Godrej/Harrison/Plaza, complete all as specified and directed by Engineer in charge.

Demolition of wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets, complete all as specified and directed by Engineer in charge.

M&L for suspended false ceiling system using chicago metallic (E grid)exposed suspended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC (High pressure steam cured) pre-primed , self embossed . textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 3- 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) with Provn of light fixture, complete all as specified and directed by Engineer in charge. Make :- EVEREST or other equivalent as approved.

Taking down rolling shutter, hood cover and guide channels etc complete rolling shutter, complete all as specified and directed by Engineer in charge.

S&F Steel rolling shutters, gear operated type with bevel gear box and crank handle type with ball bearings, complete all as specified in SSR Part-I, including tope cover, anchoring rod, hasp & staple and one shop coat of primer; erected in position (thickness of sheet/ lathes 1.25 mm and curtain inter locking curl 75 to 85 width of each trip of each strip) and making good the disturbed surfaces of walls/pillars in cement and sand mortar 1:4 and PCC 1:2:4 type B-1 for hold fasts etc, including taking down old steel shutters, complete all as specified and directed by Engineer in charge. Note: (i) Quoted rate includes making good the disturbed surfaces as per existing finished specifications. (ii) Quoted rate includes necessary use and waste of form work, if required.

S&F Steel rolling shutters, manual operated type with ball bearings, complete all as specified in SSR Part-I, including top cover, anchoring rod, hasp & staple and one shop coat of primer; erected in position (thickness of sheet/ lathes 1.25 mm and curtain inter locking curl 75 to 85 width of each trip of each strip) and making good the disturbed surfaces of walls/pillars in cement and sand mortar 1:4 and PCC 1:2:4 type B-1 for hold fasts etc, including taking down old steel shutters, complete all as specified and directed by Engineer in charge. Note: (i) Quoted rate includes making good the disturbed surfaces as per existing finished specifications. (ii) Quoted rate includes necessary use and waste of form work, if required.

Disconnecting existing tanks of capacity exc 250 ltr but n.exc 500 ltr, setting aside (or lowering if required) for repairs, Cleaning with chemical agent and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc reconnecting and re-fixing in position, complete all as specified and directed by Engineer in charge.

Disconnecting existing tanks of capacity exc 500 ltr but n.exc 1000 ltr, setting aside (or lowering if required) for repairs, Cleaning with chemical agent and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc reconnecting and re-fixing in position, complete all as specified and directed by Engineer in charge.

S&F in repairs HDPE PVC lid (cover) for 500 ltrs capacity PVC/HDPE tank, complete all as specified and directed by Engineer in charge.

S&F in repairs HDPE PVC lid (cover) for1000 ltrs capacity PVC/HDPE tank, complete all as specified and directed by Engineer in charge.

Dismantling of mild steel work of any description not other wise provided, complete all as specified and directed by Engineer in charge.

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders; framed balusters, walk ways, railings, framework of water tanks and framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc. Similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed by Engineer in charge.

Preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide paint exposed to view surfaces, complete all as specified and directed by Engineer in charge.

M/s BALDEV SINGH (BID ID -3368377)

M/s Kamal Builders (BID ID -3376452)

GUPTA AND ENGINEERS (BID ID -3368727)

OM CONSTRUCTION CO. (BID ID -3367300)

M/s Luxmi Constructions (BID ID -3365676)

REYANSH GARG AND COMPANY (BID ID -3368460)