Spl repair to Bldg No. E-17 (SM Barrack) of Fd Hosp under GE (East) Ferozepur Cantt

Amount

B/R WORK Demolition of un reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in roof kerbs or mud stops, bed blocks,back filling in chowkhats, benching etc including necessary form work complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in floor topping, 40mm thick, surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as specified and directed.

M&L for 25 mm thick cement concrete (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in sub base of flooring,surface finished rough to receive floor topping complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

Dismantling floor hearth or wall/stone tiling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises. complete all as specified and directed

M & L Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),primium quality area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed.

Glazeded ceramic coloured (colour & shade as approved) tile 450x300x7mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white/ coloured cement with pigment to match the colour of tiles complete all as specified and directed.

M&L for Machine cut kota stone slab 18-20 mm thick as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry over& including screed bed of 20 mm thick in cement mortar (1:6) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and polishing complete all as specified and directed.

M&L machine cut kota stone 16-18 mm thick as in risers of steps, skirting, dado etc over & including 15mm thick rendering in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing ccomplete all as specified and directed.

M&L for cutting, rubbing and polishing of existing kota stone in any position upto entire satisfaction of Engr-in-charge with grinding machine/hand grinder complete all as specified and directed.

Dismantling of brick tiles single layer laid on roof jointed & pointed in cement mortar complete all as specified and directed.

Demolition/taking out mud from the roofs, any thickness, including plastering and leaping etc including removing rubbish upto 500 mtr from the site complete all as specified and directed

M&L for rendering 10 mm thick in CM (1:4) mixed with integral water proofing compound as per mfg instr over the padding concrete while still the concrete is still green, complete all as specified & directed (For roof treatment)

M&L for water proofing treatment to roof surface including parapet wall comprising with the following course of treatment/ specifications form bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including preparation of roof surfaces complete all as specified and as directed. (b) One layer of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by torched application complete all as specified. Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet walls and shall be finished by a membrane flashing. Note: (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be 75mm length wise and 100 mm width wise of polymeric membranes respectively and sealed all overlaps and joints as manufacturer's instructions.

M & L for Cement concrete tiles 25cm x 25cm x 22mm thick, machin e pressed; set and jointed in neat cement slurry over 15 mm thick screed in cement mortar (1:4) and pointed in neat cement mixed with pigment to match the shade of tiles, complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in roof padding complete all as specified and directed.

Racking out of cement joints/pointing of bricks work or brick tiles laid flat in floor surface,chanels,roofs etc complete all as specified and directed.

M&L for Flush pointing to brick tiles / tarracing tiles laid flat on roofs in cement mortar 1:3 complete all as specified and directed

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches,pillars etc complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in c:m 1:6 complete all as specified and directed.

All as per srl item No 23 here-in-before but using old bricks retrieved from dismantling under ser item 22 here-in-before including cleaning and removal of mortar from old bricks etc complete all as specified and directed.

Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 15mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and fair complete all as specified and directed.

M&L for Rendering 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and fair complete all as specified and directed.

M&L for Rendering 5 mm thick cement plaster on ceiling surfaces in cement mortar 1:3 finished fair and even without using extra cement complete all as specified and directed.

M&L for Preparation of new plastered surfaces of ceiling & applying three coats of white wash complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls etc.and applying three coats of white wash complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls etc., and applying two coats of cement base paint complete all as specified and directed.

M&L for prepration of existing treatment including preparation of surfaces of walls & applying one coats of cement base paint complete all as specified and directed.

M&L for 2mm thick wall care putty on wall surface internal complete all as specified and directed.

M&L for removal of complete existing treatement on wall & Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

M&L Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new plaster surface work complete all as specified and directed.

M&L for prepration of existing treatment including preparation of surfaces of walls & applying two coats of white wash complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts and removing from site to store or otherwise as directed complete all as specified and directed.

All as per srl item No 39 here-in-before but size exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and directed.

S&F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 125mm x 60 mm including one shop coat of red oxide primer complete all as specified and directed.

S&F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mm including one shop coat of red oxide primer complete all as specified and directed.

S&F 30mm thick, Flush shutters, solid core construction, with partical board core, commercial type on both sides,one face is covered with deco rative face veneer with lipping/frame to match complete all as specified and directed.

S&F 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified and directed.

S&F Factory made box type steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

M&L for Mild steel framed work of E-165 (Fe 290) as in grills/guard bars shouldered with steel window/ ventilator frames including red oxide primer coat complete all as specified and directed.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail MS frame shall be covered with heat moulded plain / coloured PVC "C"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles & rails with suitable PVC sheet beading and jointed togeather with solvent cement complete all as specified and directed. Note :-Factory made PVC door colour approved by Engr-in charge

M&L for Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide priming complete all as specified and directed.

M&L for one coats of synthetic enamel paint including preparation of old painted wood or wood bases surface of any description over 10 cm.width or girth complete all as specified and directed.

M&L for one coats of synthetic enamel paint, including preparation of old painted steel or steel bases surface of any description over 10 cm width or girth complete all as specified and directed.

S&F PTMT butt hinges, 100 mm long and fixed with steel screws complete all as specified and directed.

S&F PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified and directed.

S&F PTMT door handle, 150 mm long and fixed with steel screws complete all as specified and directed. Make: Prayag/Polytuf.

S&F alluminium anodised handles 150 mm long fixed to doors complete all as specified and directed.

S&F alluminium anodised tower bolts 200 mm long fixed to windows complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

S&F 300 mm mild steel ordinary rat tail spring including roller and roller plate complete all as specified and directed.

S&F in repair alluminium anodised handles 150 mm long fixed to doors complete all as specified and directed.

S&F in repair alluminium anodised tower bolts 200 mm long fixed to windows complete all as specified and directed.

S&F in repair 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Ditto all as per ser Item No 66 above but fixed in repairs.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified and directed.

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

All as per ser item No 71 here-in-before but 20 mm bore tubing.

M&L for GI steel water tubing, 15mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor, complete all as specified and directed.

All as per ser item No 73 here-in-before but 20 mm bore tubing.

Fixing only,after cleaning old steel water tubing,15 mm bore and connections in new or old position using new fittings complete all as specified and directed. (pipes obtained from item 73 to be reused).

All as per item No 75 here-in-before but 20 mm bore (pipes obtained from item 74 to be reused).

S&F in repair stop valves, fancy type, CP with long shank and cup ( concealed type ), screwed both ends for 15mm bore of iron pipe or for union and fixed complete all as specified and directed.

S&F in repair piller taps, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for 15mm bore of iron pipe and fixed complete all as specified and directed.

S&F in repair gunmetal gate valve of 20mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F in repair gunmetal gate valve of 15mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F in repair bib taps, fancy type CP, screwed for 15mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F brass CP Angle cock with long shank/flange and cup (concealed type) 15 mm dia bore screwed down with crutch handle both end screwed for iron pipe or union as fixed in repairs complete all as specified and directed.

S&F in repair PVC waste pipe 32 mm bore suitable to waste coupling pipe attach with rubber ring joints fixed to waste coupling of sinks / WHBs/Urinal complete all as specified and directed.

S&F in repair Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified and directed.

S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified and directed.

S&F in repair Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pan ( pedestal pattern ), white/ coloured including seat & cover, flush pipe, connection to drain and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed.

S&F in repair PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. complete all as specified and directed.

S&F in repair Vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified and directed.

S&F in repair Vitreous China urinals, half stall type ,white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) Complete all as specified.

S&Fin repair PTMT grating doom 100mm dia with or without waste hole fixed in repairs complete all as specified and directed.

S&F in repair 125 mm chromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union complete all as specified and directed.

S&F Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs as in repairs complete all as specified and directed.

S&F Stainless steel soap dish (not less than 1mm thick) of type as directed,fixed to walls with chromium plated brass screws with wooden/rawl plugs,in repair complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out from wall/trenches, if required complete all as specified and directed.

Taking down eaves gutters and rain water pipes( any size or pattern),including all fittings heads shoes bends swan-necks etc complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed to walls or laid in trenches complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm dia Junction single (Single or double T) equal or unequal complete all as specified and directed.

S&F 110mm dia Junction single (Single or double T) equal or unequal complete all as specified and directed.

M&L PVC (SWR) floor trap 75 mm, plain with PVC grating including jointing with solvent cement etc., complete all as specified and directed.

S&F Mild steel curtain rod powder coated with fixing side brackets,end cups,rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floor and paving exceeding 15 cm thickness but above ground floor complete all as specified and directed.

M&L for 10 mm thick rendering over concrete surface of sunken floor in CM 1:3 and applying bitumen blown any grade applied two coats to concrete surface / rendering at the rate of 1.5 kg per sqm per coat and treating the sunken floor complete all as specified and directed.

M&L for water proofing treatment to RCC sunken floor including wall comprising with the following course of treatment/ specifications form bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.40 ltr per sqm including preparation of roof surfaces complete all as specified and as directed. (b) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. Note: (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be not to be less than 150mm of polymeric membranes and sealed all overlaps and joints as manufacturer's instructions.(iii) All CI/PVC traps in sunken slabs to be enclosed with PCC 1:1.5:3(min 15 cm) all round complete all as specified and directed.

M&L for Cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregate as in filling in sunkan slab or in mass concrete complete all as specified and directed.

M&L for GI steel water tubing, 40mm bore medium grade galvanized with all fittings and fixed as in spout pipe in sunkan slab, complete all as specified and directed.

M&L for 25mm thick precast cement concrete jafferi jallies,(1:2:4) 12.5mm graded stone aggregate type BO (measured solid), including all mouldings but excluding frame all as specified and as directed

Repair to existing window/ ventilator with necessary fittings such as welding,cutting,handle,hooks,and other miscellaneous items which is required to repair of window/ventilator shutter to make easy for opening and closing complete all as specified and directed.

S&F 0.71mm thick Plain, Aluminium sheeting, Alloy 31000 H4 as in crumple joint sheet, ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed), including fastening, screw etc for fixing etc complete all as specified and directed.

Material and labour for applying bond coat of epoxy bonding agent & cement mortor in 1:1 ratio for bonding old and new concrete on damaged surfaces applying ready mix polymer modified mortar upto 60mm thickness (Chajjas fins, border,slab, beams etc) :- (i) Including application of rust remover on exposed reinforcement and subsequent application of anticorrosive coating. Also, pressure grouting with epoxy injection after application of polymer modified mortar. (ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repeat this step after 24 hrs as required. (iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as directed by Engineer-in-Charge. Make of Chemicals : - Epoxy bonding agent, Rust remover, Anti corrosive coating, Polymer modified mortar, Epoxy grout shall be of Berger, Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika or Equivalent as approved by GE. Notes : (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE). (ii) The Contractor and manufacture of polymer modified mortar shall give the warranty before commencement and also for the strengths achieved in the post completion of work. (iii) The chemicals to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (iv) Hard drawn steel wire fabric will be measured and paid seperately complete all as specified and directed.

S&F mild steel TMT bars as in reinforcement 10mm dia and over cut to length,bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & directed.

S&F mild steel TMT bars as in reinforcement 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length,bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & directed.

Material and labour for shotcreting average thickness 50 mm in RCC columns, beams and slab etc. with cement concrete M-25 design mix having minimum cement content of 350 Kg per Cum. Concrete having the specified minimun characterstic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6 mm maximum size in proportion as per design criteria and Hardener/ admixture) incl the cost of centering and shuttering at edges and corner etc as directed by Engineer-in-Charge incl chipping of unsound/week concrete mateial 50 mm average thickness from slabs, beams/ columns etc with mannual chiesels or standerd power driven percussion type machine incl tapering of all edges, make square shoulder of cavities incl cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removal of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron, applying the SBR Latex based bonding agent on each layer of the shootcreting work of Dr Fixit Pidicrete URP on the entire surface complete all as directed including pressure grouting with epoxy injection grout including 5 mm thick cement plaster in CM (1:3) finished even and smooth without using extra cement including removing rubbish material from building and thrown in low lying lying area at any distance upto 500 metres from the site complete as directed by Engineer-in-Charge. Make of chemical : Epoxy bonding agent, Rust remover, Anti corrosive coating, Epoxy grout, Hardener/ admixture shall be of Berger/ Sika/Fosroc/Pidilite or Techno commercial or equivalent make approved by GE. Notes : (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE). (ii) The Contractor and manufacture of shotcrete shall give the warranty before commencement and also for the strengths achieved in the post completion of work. (iii) The chemicals to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (iv) Hard drawn steel wire fabric will be measured and paid seperately

Supply and fixing hard drawn steel wire fabric not exc 4 kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

E/M WORK Taking down carefully existing copper/alumimium point wiring for light/fan/socket out let points complete with fitting and fixtures, battens, wire etc and making good the disturbed surfaces of walls and ceilings, complete all as specified and directed.

Taking down unserviceable main switches, electric metres and distribution boards single phase complete all as specified and directed.

Taking down carefully old unserviceable sub main wiring and making good disturbed sufaces and matching with existing complete all as directed and specified.

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed,stranded (Green colour) connected to common earth dolly complete all as specified and directed for following : - (a) One light/fan/bell/exhaust point controlled by one single pole one way switch. Make:- Polycab/ SCI / Havells

(b) One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board complete all as specified and directed. Make:- Polycab/ SCI / Havells

(c) One 3 pin 5 Amp socket outlet point controlled by one switch on same board complete all as specified and directed. Make:- Polycab/ SCI / Havells

All as per item 122 above, but one switch socket outlet multi purpose, 3pin, 15 Amps, point to be controlled by one switch and wiring with 2.5 Sqmm PVC FRLS cable, insulated, stranded, unsheathed copper conductor on Independent board with continuous earth wire of size 2.5 sqmm, PVC FRLS copper conductor, insulated, unsheathed, stranded, complete all as specified and directed. Make:- Polycab/ SCI / Havells

All as per item 122 above, but one switch socket outlet multi purpose, 3pin, 15 Amps, point to be controlled by one switch and wiring with 4 Sqmm PVC FRLS Cable, insulated, stranded, unsheathed copper conductor on Independent board with continuous earth wire of size 4 sqmm, PVC FRLS copper conductor, insulated, unsheathed, stranded, complete all as specified and directed. Make:- Polycab/ SCI / Havells

S&F Switch, piano, flush type, single pole one way, 5 Amps, ISI marked, complete all as specified and directed.

S&F Switch piano flush button type 15 Amps, single pole, one way, ISI marked, complete all as specified and directed.

S&F Socket outlet,2 in 1, 5 pin, 5 Amp, piano flush type, ISI marked, complete all as specified and directed.

S&F Socket outlet 2 in 1, 6 pin,5 Amp and 15 Amp, piano flush type, ISI marked, complete all as specified and directed.

S&F Ceiling rose, surface type, backelite 65mmx50mm, 3 terminals complete all as specified and directed.

S&F Lamp holder, insulated body, threaded dome pattern, suitable for bracket/batten fittings, complete all as specified and directed.

S&F in repairs stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 230 volts, 6 Amps, complete all as specified and directed.

Supply and fixing LED light fitting 1 x 20 Watt, 220V, AC Tube light 4 feet square connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED bulb of 9/10 watts B-22 CDL 3 star 6500K, complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, suitable size GI bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection including all necessary fixing arrangement, complete all as specified and directed.

S&F in repair, Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, VTPN DB with 200 Amps rated bus bar, 4 way, FP-42 protection surface mounting, 415 volts, dust and vermin proof, suitable for incorporation of MCCBs duly concealled in wall, factory made, including thermal based release adjustable type 4 pole, 63 Amps, 50 Hz, 415 volts with rupturing capacity 16 KA and making good disturbed surfaces with matching colour, complete all as specified and directed.

S&F in repair Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet, powder coated, SPN DB with 200 Amps rated bus bar, 8 way, FP-42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of MCCBs duly concealled in wall, factory made,including making good disturbed surfaces with matching colour, complete all as specified and directed.

S&F in repairs MCB, SPN, 40 Amps, 240 volts 10KA duly ISI marked, complete all as specified and directed.

S&F in repairs MCB, single pole, 240 Volt, 6 to 32 Amps, 10 KA complete all as specified and directed.

S&F in repairs for sub main wiring with two single core PVC FRLS insulated unsheathed stranded copper conductor cable FRLS 2x10 Sqmm single core 650/1100 V, drawn through & including rigid PVC rigid conduit 25 mm dia including continuous earth wire of size 1x10 sqmm, PVC insulated and unsheathed cable copper stranded conductor (green colour), complete all as specified and directed. NOTE:- Two runs of cable, 1 run of earth wire & one run of PVC conduit shall be measured as one length.

S&F in repairs for sub main wiring with two single core PVC FRLS insulated unsheathed stranded copper conductor cable FRLS 2x6 Sqmm single core 650/1100 V, drawn through & including rigid PVC rigid conduit 25 mm dia including continuous earth wire of size 1x6 sqmm, PVC insulated and unsheathed cable copper stranded conductor (green colour), complete all as specified and directed. NOTE:- Two runs of cable, 1 run of earth wire & one run of PVC conduit shall be measured as one length.

S&F heavy duty, 900 RPM Exhaust fan AC single phase 230/240 Volts of 300mm sweep with louver plastic body, including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection, complete all as specified and directed.

Cutting hole of suitable size and making good, the disturbed surface, grouting nuts & bolts for fixing of exhaust fans, complete all as specified and directed.

M&L Earthing as in repairs complete, all as shown on electrical plate No 3 of MES schedule part-I, and as specified including the following:- (i) Galvanised steel earth plate of size 60cmsx60cmsx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth not less than 1.50 metre below normal ground level. (ii) Earth plate surrounded by and packed with char-coal and common salt in alternative layers (n.exc 15cms each layer). (iii) 4 mm dia (8 SWG) G.I earth wire from earth plate to main switch board including necessary GI bolts, nuts check nuts, washers, thimbles etc. (iv) 15 mm bore light grade, GI pipe for protection to earth-strip. (v) 20mm bore, medium grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horizontally to the earth pit. (vi) 50mm thick pre-cast cover of cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate and MS angle iron 25x25x3mm frame including two coats of painting over a coat of red oxide to exposed steel surfaces. (vii) Excavation in soft/loose soil, returning filling & removal of surplus soil to a distance upto 50 metre complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with steel inner tank and heating elements upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 50 Sqmm nominal cross section, 4 core, insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and not exc 10 Sqm on plan, for laying of cable and getting out, complete all as specified and directed.

M&L Dry and clean fine sand for cable cushioning to underground cable protection, ccomplete all as specified and directed. (Excavation and earth work measured separately). Note- Punned down thickness shall be measured.

S&F in repair Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified and directed. (Excavation and earth work measured separately.

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified and directed.

Removal of surplus soil to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.5 metre above the starting point complete all as specified and directed.

S&F Mild steel galvanised pipe, light grade, 50 mm nominal bore for passing of cable, fixed to poles/walls, laid under floor/road crossings, complete with and including clamps socket & elbow etc complete all as specified and directed.

Vee Vee Enterprises (BID ID -3263022)

KAILASH CONSTRUCTION COMPANY (BID ID -3263383)

M/s Sidhu Bros (BID ID -3263235)

M/s S B Construction Company (BID ID -3263083)

M/s Vishant Construction Co (BID ID -3263558)

B.L. Chaudhri and Co. (BID ID -3263230)

MS CHARANJIT SACHDEVA (BID ID -3263520)