REPAIR REPLACEMENT OF BROKEN PARTS, RECANNING AND POLISHING TO VARIOUS WOODEN FURNITURE AT CHANDIPUR AND BALASORE

Amount

NOTE (Applicable for all items) :- The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates. BED PLYWOOD TOP (FD-246) : M&L for carrying out repair and replacement of the following parts of bed plywood top all as shown in Drawing and as directed by Engr-in-Charge :-

S&F plytop made out of 12mm thick commercial plywood of size 1800x900mm BWR ISI marked IS-303 (Make: National/kitply/green ply) as approved by GE

S&F long rail frame of size 35x90x1980 mm long made out of 1st class HW (Teak)

S&F head board frame made out of 1st class HW with 4mm thick OST plywood (Teak) as per existing shape & size.

S&F foot board frame made out of 1st class HW with 4mm thick OST plywood (Teak) as per existing shape & size.

S&F stiffiner to support made out of 1st class Hard Wood (Teak) of size (40x60x880)mm.

S&F Short rail frame of size 60x60x900 mm made out of 1st class HW (Teak)

S&FLeg of size 60x60x 660mm made out of 1st class H/W (Teak)

S& F Flat iron L shape clamp 35mm x5mm bent to right angle

Apply one coat french polish to bed plywood top to obtain smooth, glossy finish including necessary preparation of surfaces.

SIDE BOARD (FD-241) : M&L for carrying out repair and replacement of the following parts of side board. Removing carefully the existing unserviceable/damaged parts of side board and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge :-

Top made out of 18mm thick prelaminated partical board exterior grade, phenyl formoldehyde bonded, flat pressed three layer BWR type-II, Make: Archidlam/Novapan/Kitply ISI marked fixed with mild screws as per size and shape including 4mm thick teak wood beading all around as directed by Engr-in-Charge.

S&FSide 18mm thick plywood BWR of size 455 x 625mm

S&F Back, 6mm thick plywood BWR of size 1220 x 625mm

S&F Drawers as per drg

S&F Door of size 585 x 835 x 18mm BWR plywood

S&F Shelves of size 455 x 835 x 18mm thick BWR plywood

S&F Leg of size 45x45mm at top 25x25mm at bottom made out of 1st class HW (Teak)

S& F long rail size of 25 x 45 mm made out of 1st class H/W ( Teak)

S& F short rail of size of 25 x 45 mm made out of 1st class H/W ( Teak)

S&F Knob, chromium plated

Apply one coat french polish to side board dressing to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F brass hinges 50mm

DIWAN WOODEN PLATFORM (GE/CDP/F/13/85) : M&L for carrying out repair and replacement of the following parts of diwan wooden platform. Removing carefully the existing unserviceable/damaged parts of diwan wooden platform and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge :-

Leg of size 60x60mm at top and 40x40mm at bottom made out of 1st class hardwood teak

Long rail frame 30x100x1860mm long made out of 1st class hardwood teak

Short rail frame 30x100x600mm long madeout of 1st class hardwood teak

Plywood of size 1800x600x12mm thick BWR for diwan top make- national /century/kitply 20x100mm beading of edges alround the top made out of 1st class hardwood teak

Support 25x32x580mm made out of 1st class hardwood teak

Seat cushion of size 1800x600x75mm thick 32 density make - Sleepwell/feather foam/ cool foam duly covered with tapestry cloth of superior quality rate of tapestry cloth should not less than Rs180 per mtr.

Applying one coat of french polish after preparation of surface complete to Diwan wooden platform.

TABLE WRITING (FD-275) : M&L for carrying out repair and replacement of the following parts of table writing.Removing carefully the existing unserviceable/damaged/broken parts of table writing and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge :-

S&F of table top of size 1175x600mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg (35 x 55x732)mm high made out of 1st class HW (Teak).

S&F of top long rail (25x50x790)mm long made out of 1st class HW (Teak).

S&F of top short rail (25 x50x600)mm long made out of 1st class HW (Teak).

S&F of bottom rail (side stiffner) (20x50x355)mm long made out of 1st class HW (Teak).

S&F of foot rest (stiffner) (20x50x1145)mm long made out of 1st class HW (Teak).

S&F of drawer as per existing shape and size

S&F of back of table writing of size (355 x 732)mm made out of 6mm thick BWR grade ply wood.

S&F of door of cupbaord as per existing size & shape made out of 18mm thick prelamianted Particle Board beaded all around with Teak Wood beading

S&F of brass hinges 50mm long.

S&F of chromium plated Knob as per existing size and, shape

Apply one coat french polish to table writing to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

TABLE DINING FOR 3 PERSONS (GE/CDP/F/13/85) : Removing carefully the existing unserviceable/damaged parts of table dining for 3 persons and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge :-

S&F of table top of size 1200 mm x 900 mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size 60 mm x 60 mmt top and (50 x 50) mm at bottom and 750 mm height made out of 1st class HW (Teak).

S&F of long rail of size (25 x 100 x 1200)mm long made out of 1st class HW (Teak).

S&F of short rail of size (25x100x900)mm long made out of 1st class HW (Teak).

S&F of triangular bracket(as support) made out of 2nd class HW (Teak) as per size and shape.

Apply one coat french polish to table dining 3 persons to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

TABLE DINING 120 CM x 90 CM (FD/E-6/MAP-II/03) : - Removing carefully the existing unserviceable / damaged parts of table dining for 3 persons and supply and fix of new parts / components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of table top of size 1200 mm x 900 mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size 90 x 45 x 750mm heigh made out of 1st class HW (Teak).

S&F of long rail of size (45x90x1200)mm long made out of 1st class HW (Teak).

S&F of short rail of size (45x90x900)mm long made out of 1st class HW (Teak).

S&F stiffner sze 90x25x900m made out of 2nd class hard wood ( teak

S&F of triangular bracket(as support) made out of 2nd class HW (Teak) as per size and shape.

Apply one coat french polish to table dining 3 persons to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

TABLE DINING FOR 8 PERSONS (FD-273) : - M&L for carrying out repair and replacement of the following parts of Table dinning 8 pers.Removing carefully the existing unserviceable/damaged parts of Table dinning 8 pers and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of table top of size 1800 mm x 900 mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size 40 x 75 x 732mm made out of 1st class HW (Teak)

S&F of long rail 25 x 100 x 1800mm made out of 1st class HW (Teak)

S&F of short rail 25 x 100 x 900mm made out of 1st class HW (Teak)

S&F of triangular bracket (as support) made out of 2nd class HW (Teak) as per required shape & size.

Apply one coat french polish to table dining 8 persons to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

TABLE DINING FOR 6 PERSONS (FD-273) : - Removing carefully the existing unserviceable/damaged parts of table dining for 6 persons and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of table top of size 1500x900mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size (40 x 75 x 732)mm, high made out of 1st class HW (Teak).

S&F of long rail of size (25 x 100 x 1500)mm long made out of 1st class HW (Teak).

S&F of short rail of size (25 x 100 x 900)mm long made out of 1st class HW (Teak).

S&F of triangular bracket (as support) made out of 2nd class hard wood (Teak) as per shape & size

Apply one coat french polish to table dining 6 persons to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

TABLE BEDSIDE (FD-276) :- M&L for carrying out repair and replacement of the following parts of table bed side. Removing carefully the existing unserviceable/damaged parts of table bed side and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of top 18mm thick BWR grade plywood of size 230x450mm fixed with 1mm thick laminated sheet at top

S&F of side 18mm thick BWR grade plywood of size 230x510mm fixed with 1mm thick laminated sheet at top

S&F of shelves 12mm thick BWR grade plywood teak face of size 230x450mm

S&F of backply 6mm thick BWR grade of size 510x450mm

Applying one coat of french polish after preparation of surface complete to table Bedside to obtained smooth, glossy finish including necessary preparation of surface.

TABLE DRESSING GENTS WITH MIRROR (FD-230) : - M & L for carrying out repair / replacement of following parts of Table Dressing Gents With Mirror as per drawing after dismantling the old parts complete all as specified :-

S&F of table top made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

Bottom partition using 18/19mm thick block board ISI Marked Make (Action tesa/Archid/Novapan) commercial of size 900 x300mm.

Repair/replacement of drawer complete all as specified & drg.

Mirror 5mm thick of make Atul/Saint-Govin/Modi guard with frame of Teak wood (MP Teak). As per existing size and shape and all as directed by Engr in-charge

Applying two coats of French polish (ready made) to article after necessary preparation of surfaces .

Knob CP for drawer as per existing size and shape

TABLE DRESSING LADIES (FD-251) : M & L for carrying out repair / replacement of the following parts and supply & fix of new parts as under of Table Dressing Ladies as per drg :-

S&F of leg of size 45x45x75mm made out of 1st class hard wood (Teak)

S&F of long rail of size 40x25x900mm made out of 1st class hard wood (Teak)

S&F of short rail of size 40x25x380mm made out of 1st class Hard wood (Teak)

S&F of drawer as per existing shape and size

S&F of knob CP as per size & shape

S&F of telescopic channel for drawer as per existing size and shape

S&F of handle CP 75mm

S&F replacement of old defaced of mirror of size 360x1220mm Make : Modi guard/Atul/Saint gobain with 1st class hard wood (Teak) frame all around complete as per drawing

Apply of polishing to table dressing with glossy finish by applying one coats of french polish including necessary preparation of surface

TABLE OF SIZE 900 x 600 x 760 MM WITH DRAWER (FD-283) : - M&L for carrying out repair and replacement of the following parts of table 900 x 600 x 760 mm. Removing carefully the existing unserviceable/ damaged parts of table 900 x 600 x 760 mm and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge :-

S&F of table top made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size 60 x 30 x 740mm high made out of 1st class HW (Teak).

S&F of long rail of size 20 x 60 x 900mm long made out of 1st class HW (Teak).

S&F of short rail of size 20 x 60 x 600mm long made out of 1st class HW (Teak).

S&F of stiffiner of size 25 x 40x600mm long made out of 1st class HW (Teak).

S&F of drawer as per existing shape & size made out of 1st class HW (Teak).

S&F Chromium plated knob as per existing size and shape.

Apply one coat french polish to table 900x600x760mm (3'x2') with drawer to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

STOOL DRESSING CB (FD-252) :- M&L for carrying out repair and replacement of the following parts of stool dressing CB. Removing carefully the existing unserviceable/damaged parts of stool dressing CB and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge :-

S&F of leg of size 45x45x370mm made out of 1st class hardwood teak

S&F of top long rail 50x25x450mm made out of 1st class hardwood teak

S&F of top short rail 50x25x300mm made out of 1st class hardwood teak

S&F of stiffiner 25x19x 450mm made out of 1st class hardwood teak

S&F of side rail bottom 50x25x300mm made out of 1st class hardwood teak

S&F of hard rubber shoes

Applying one coat of french polish after preparation of surface complete to stool dressing CB to obtained smooth, glossy finish including necessary preparation of surface.

CHAIR WOODEN BOTTOM W/O ARM (FD-56(M), FD-285) : - M&L Removing carefully the existing unserviceable/damaged parts of chair wooden bottom w/o arm and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of front leg of size 50 x 50 x 445mm high made out of 1st class HW (Teak).

S&F of rear leg of size 40 x 65 x 840mm high made out of 1st class HW (Teak).

S&F of front rail of size 25 x 65 x 415mm long made out of 1st class HW (Teak).

S&F of rear rail of size 25 x 65 x 375mm long made out of 1st class HW (Teak).

S&F of side rail of size 25 x 65 x 400mm long made out of 1st class HW (Teak).

S&F of back stiffner 15 x 50 x 375mm long (slightly curve) made out of 1st class HW (Teak).

S&F of stiffiner of size 20 x 25 x 400mm long made out of 1st class HW (Teak) provided 100mm high from bottom.

S&F in replacement of seat made out of 6mm thick plywood BWR grade ISI marked with 6mm dia preparations to be provide to plywood seat(Make: National/kitply/green ply) as approved by GE

Apply one coat french polish to chair wooden bottom w/o arm to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F of hard rubber shoes

CHAIR WRITING (FD-280 & FD-250) :- M&L Removing carefully the existing unserviceable/damaged parts of chair writing and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of front leg of size 55 x 30 x 660mm long made out of 1st class HW (Teak).

S&F of rear leg of size 55 x 30 x 890mm long made out of 1st class HW (Teak).

S&F of arms of size 55 x 19 x 495mm long made out of 1st class HW (Teak).

S&F of rails of size 30 x 65 x 490mm long made out of 1st class HW (Teak).

S&F of stiffiner of size 25x20 x 450mm long made out of 1st class HW (Teak).

S&F of back Stiffiner of size 12 x 50 x 445mm made out of 1st class HW (Teak).

Apply one coat french polish to chair writing to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape.

CHAIR DINING (FD-279 & 228) : - M&L Removing carefully the existing unserviceable/damage parts of chair dinning and supply and fixing of new parts/ components of required size and shape as per drg to match with the existing including re-assembling with suitable size of bamboo pins complete all as shown in drg and as directed by Engr-in-Charge.

S&F of front leg of size 45mm x 45mm x 460mm high made out of 1st class HW (Teak).

S&F of rear leg of size 45mm x 65mm x 890mm high made out of 1st class HW (Teak).

S&F of stiffiner of size 25mm x 19mm x 400mm long made out of 1st class HW (Teak).

S&F of front rail of size 30 x 65 x 400mm long made out of 1st class HW (Teak).

S&F of rear rail of size 30 x 65 x 400mm long made out of 1st class HW (Teak).

S&F of side rail of size 30 x 65 x 380mm long made out of 1st class HW (Teak).

S&F of back stiffner of size 15 x 50 x 390mm long horizontal rest slightly curved U shape made out of 1st class HW (Teak).

S&F plastic rubber shoe white/black best quality as per existing size and shape

Apply one coat french polish to chair dinning to obtain smooth, glossy finish including necessary preparation of surfaces.

CHAIR CB/CB OFFICE (DB-4124 & 3954) : M&L Removing carefully the existing unserviceable/damaged parts of chair CB / CB office and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of front leg of size 50 x 50 x 600mm high made out of 1st class HW (Teak).

S&F of rear leg of size 40 x 90 x 890mm high made out of 1st class HW (Teak).

S&F of front rail of size 35 x 50 x 470mm long made out of 1st class HW (Teak).

S&F of rear rail of size 35 x 50 x 440mm long made out of 1st class HW (Teak).

S&F of side rail of size 35 x 50 x 420mm long made out of 1st class HW (Teak).

S&F of stiffiner of size 20 x 25 x 460mm long made out of 1st class HW (Teak).

S&F of arms of size 35 x 35 x 460mm long made out of 1st class HW (Teak).

Apply one coat french polish to chair CB/CB office to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

CHAIR EASY (FD-17(M) & FD-229) : - M&L removing carefully the existing unserviceable/damaged parts of chair easy and supply and fixing of new parts/ components of required size and shape as per drg to match with the existing including re-assembling with suitable size bamboo pins complete all as directed by Engr-in-charge

S&F of leg of size 55 x 25 x 535mm high made out of 1st class HW (Teak).

S&F of arms of size 65 x 25 x 610mm long made out of 1st class HW (Teak).

S&F of front rails of size 25 x 70 x 520mm long made out of 1st class HW (Teak).

S&F of side rails of size 25 x 70 x 520mm long made out of 1st class HW (Teak).

S&F of rear rail of size 50 x 25 x 500mm long made out of 1st class HW (Teak).

S&F of back frame of size 55 x 20 mm made out of 1st class HW (Teak).

Apply one coat french polish to chair easy to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

RECANNING OF ALL TYPE OF CHAIRS : - M&L for recanning of chairs with plastic cane (oval shape) 2mm wide and border with 3mm wide cane complete as per Godrej patren using (Make: SHAH/PREMIER) brand cane (removing of old broken cane shall be done at BSO yard)

Chair dinning (FD-228, 279)

Chair easy (FD-17 (M), 229)

Chair Writing (FD-250, 280)

Chair CB/CB office (DB-4124 & 3954)

Stool dressing CB (FD-252)

SOFA SET 5 SEATED/ 4 SEATED WITH DETACHABLE CUSHION (FD-281) : M & L for carrying out repair / replacement of the following parts and supply & fix of new parts as under of Table Dressing Ladies as per drg

S&F of long rails of seat for three seater sofa of size 1590mmx100mmx35mm of 1st class hardwood (teak) duly plained and smoothed with sand paper.

All as per Srl Item No. 20.001 above but Side rail of size 575mm x 100mm x 35mm.

All as per Srl Item No. 20.001 above but long rail of back of size 1590mm x100mm x 35mm.

S&F of long rails of seat for singel seater sofa of size 590mmx100mmx35mm of 1st class hardwood (teak) duly plained and smoothened with sand paper.

All as per Srl Item No. 20.004 above but Side rail of size 575mm x 100mm x 35mm.

All as per Srl Item No. 20.004 above but long rail of back of size 590mm x 100mm x 35mm.

Replacement of arms for Single / Three seater sofa of size 35mm x 70mm (cross section) of 1st class hard wood (MP Teak) complete all as specified and shown on drgs after removing the old broken arms.

All as per Srl Item No. 20.007 above but batten of size 50mm x 20mm.

Replacement of legs for Single / Three seater sofa of size 35mm x 70mm (cross section) of 1st class hard wood (MP Teak) complete all as specified and shown on drgs after removing the old broken legs.

Applying one coat of french polish sofa after preparation of surface complete to sofa 3 seater

Applying one coat of french polish after sofa preparation of surface complete to sofa single chair.

M&L in replacement of existing old warnout unserviceable cushion 32 density, 100mm thick of 530x560 mm size covered with tapestry cloth not less than Rs. 200/- per R/M as approved by GE. MAKE : SLEEP WELL/COOL FOAM/FEATHER FOAM.

S&F plastic rubber shoe white/black best quality of size 25mm

Chair Dining JCOs/ORs (FD/E6/MAP-II/05) : - M&L for carrying out repair and replacement of the following parts of chair dining JCOs/Ors. Removing carefully the existing unserviceable/damaged parts of chair dining JCOs/Ors and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S& F Front leg of size 30x55x450 mmlong madeout of 1st class hardwood teak

S& F Rear leg of size 50x32x890mm long made out of 1st class hardwood teak

S& F front rail of size 30x65x440mm long made out of 1st class hardwood teak

S& F rear rail of size 30x65x405mm long made out of 1st class hardwood teak

S& F side rail of size 30x65x390mm long made out of 1st class hardwood teak

S& F Back stiffner 45x15x390mm long made out of 1st class hardwood teak

S& F stiffner of 'H' shape of size 20x25 mm long made out of 1st class hardwood teak

S& F 04x10 mm thick ribs moulded along with seat in single piece pvc seat having 04mm thick holes

Applying one coat of french polish after preparation of surface complete to dinning chair

S&F plastic rubber shoe white/black best quality as per existing size and shape

SOFA SINGLE SEATER 600 x 750 x 675 MM (TP) : M&L for carrying out repair,/replacement of the following parts and supply & fix of new parts as under of Sofa single Seater as per drg

100mm thick high density foam cushion (Make: Sleepwell/Feather Foam/Cool Foam) duly covered with tapestry cloth over long cloth for seat complete of size 600x750mm.

All as per item No 22.001 here-in-above but for back complete 675x750mm.

Side frame of size (675x750)mm made out of 6mm BWR grade 25mm HD foam cushion duly covered with tepstry cloth

S&F Hand rest complet as per existing size and shape made out 1st class hard wood teak.

Polishing to sofa single seater with french polish to obtain smooth glossy finish.

TABLE 5'x2'-10" (F-17) : M&L for carry out repair and replacement of the following parts of table conference, removing carefully the existing unserviceable / damaged parts oftable conference and supply and fixed of new parts / componetns as per required size and shape to match with existing including re-assembling complete all shown in drg. and as directed by Engr -in Charge

S&F leg of size 50x50x750 mm made out of 1st class hard wood teak

S&F stiffner of size 25x50x1500 mm made out of hard wood teak

S&F top long rail of size 25x100x1500 mm made out of 1st class hard wood teak

S&F top short rail of size 25x100x850 mm made out of hard wood teak

S&F in replacement of Table top of size 1500x850 mm made out of 18mm thick plywood of BWR grade with 1mm thick plastic laminated sheet and 4mm thick TW beading all round. Bottom side of the top shall be painted with a coat of white primer.

S&F drawers as per drawing

S&F Plastic rubber shoes white/black as per required size and shape.

S&F CP Handle 75mm long

M&L for polishing to table conference with glossy finsh by applying two coats of french polish incuding necessary preapration of surfaces

HEAVY DUTY TABLE (FD/CCE/R&D/ BLS/43) : Removing carefully the existing unserviceable/ damaged parts of heavy duty table and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F Leg of size 80X30X750 mm high made out of 1st class hard wood teak

S&F Long rail of size 90X30X1500 mm long made out of 1st class hard wood teak

S&F Short rail of size 90X30X900 mm long made out of 1st class hard wood teak

S&F of table top of size 1500x900mm made out of 25mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

Applying one coat of french polish after preparation of surface complete to heavy duty table to obtained smooth, glossy finish including necessary preparation of surface.

TABLE BEDSIDE (FD/E6/MAP/15R) : - M&L for carrying out repair and replacement of the following parts of table bed side. Removing carefully the existing unserviceable/damaged parts of table bed side and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

Leg madeout of 18mm MS suare pipe of 18 guage as per existing shape and size duly painted with black enamel paint

Top made out of 18mm thick prelaminated partical board make - Archid/ Novapan/ Action Tesa of size 450mmx450mm including PVC edeging alroung of top

Side made out of 18mm thick prelaminated partical board make - Archid/ Novapan/ Action Tesa of size500mmx450mm

Front Shutter made out of 18mm thick prelaminated partical board make - Archid/ Novapan/ Action Tesa of size 400mmx300mm

Bottom made out of 18mm thick prelaminated partical board make - Archid/ Novapan/ Action Tesa of size 450mmx450mm

Back made out of 18mm thick prelaminated partical board make - Archid/ Novapan/ Action Tesa of size600mmx450mm

Drawer as per existing shape and size

Telescopic channel for drawer as per exsiting size and shape

Auto closure hinges as per existing pattern

Handle CP for drawer and shutter

S&F plastic rubber shoe white/black best quality as per existing size and shape

LOCKER (FD-222) : M&L for carry out repair and replacement of the following parts of locker, removing carefully the existing unserviceable / damaged parts of locker and supply and fixed of new parts / componetns as per required size and shape to match with existing including re-assembling complete all shown in drg. and as directed by Engr -in Charge ,

S&F in replacement of Top and bottom plank of locker of size (610x760x20mm) made out of 1st class HW ( Teak)

S&F in replacement of Leg of size 50x 50mm at top & 40mm x 40mm at bottom of length made out of 1st HW ( Teak)

S&F in replacement of Long rail frame os size 40x25x600mm long made out of 1st clast HW ( Teak)

S&F in replacement of Short rail frame os size 40x25x450mm long made out of 1st class HW ( Teak)

S&F in replacement of Door of size 300 x 900mm made out of 18mm thick plywood BWR grade

S&F in replacement of Side of size 600x 900 made out of 18mm thick plywood BWR grade

S&F in replacement of Partition made out of 18mm thick plywood BWR grade

S&F in replacement of Back of size 900x 750 made out of 6mm thick commercial plywood BWR

S&F in replacement of shelves made out of 12mm thick plywood BWR grade

S&F in replacement of CP Piano hinges with screw of existing size and shape

S&F in replacement of aluminium Handle anodised 100mm long

S&F in replacement of Hasp & staple aluminium anodised 75mm long

S&F in replacement of 20mm aluminium anodised rod 300mm long with socket for hanging of cloth.

M&L for polishing to locker with glossy finsh by applying two coats of french polish incuding necessary preapration of surfaces

BOARD NOTICE 1830x1220 MM (FD-99(M)) : M & L for carrying out repair,/replacement of the following parts and supply & fix of new parts as under of board notice as per drg

S&F of frame of size 75X50X1830 mm made out of 1st class hard wood teak

S&F of frame of size 75X50X1750mm made out of 1st class hard wood teak

S&F of style of size 45X25X1755 mm made out of 1st class hard wood teak

S&F of style of size 45X25X1760 mm made out of 1st class hard wood teak

S&F of stiffiner 19X25X1760mm made out of 1st class hard wood teak

S&F of stiffiner 19x25x1150mm made out of 1st class hard wood teak

S&F 12mm soft board of size 1755X1445 mm

S&F achorolic sheet of size 1115x1070 mm and 5 mm thick(both side)

S&F cloth green blaze of size 1800X1200 mm

S&F alluminium hasp and staple 100mm

S&F alluminium handel 150mm

Applying one coat of french polish after preparation of surface complete to board notice to obtained smooth, glossy finish including necessary preparation of surface.

BOOK CASE (FD-237) : M & L for carrying out repair,/replacement of the following parts and supply & fix of new parts as under of book case as per drg

S&F of top of size 1200x380 mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of front leg of size 45mm x 45mm x 100 mm high made out of 1st class HW (Teak).

S&F of long rail of size 40x25x760 mm high made out of 1st class HW (Teak).

S&F of short rail of size 40x25x200 mm high made out of 1st class HW (Teak).

S&F of back of size 1200x760x6 mm thick made out of comercial plywood BWR grade.

S&F of side of size 750x300x18 mm thick made out of 18mm OST plywood

S&F of shelves of size 380x205x18 mm thick made out of 18mm OST plywood

S&F of shelves of size 735x275x18 mm thick made out of 18mm OST plywood

S&F of CP knob as per existing size and shape

S&F of hinges of size 50mm as approved by Engineer-in-Charge

S&F of ball spring catch ball as per existing shape and size

Applying one coat of french polish after preparation of surface complete to book case to obtained smooth, glossy finish including necessary preparation of surface.

TABLE OFFICE CLERK (DB-4219) : M&L for carrying out repair and replacement of the following parts of table office clerk.Removing carefully the existing unserviceable/damaged parts of table office clerk and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of table top of size 1290X830mm made out of 18mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F in replacement of leg of size 50x50X750mm made out of 1st class hard wood teak.

S&F bottom rail(side stiffiner) of size 20X50X800 mm made out of 1st class hard wood

S&F long rail of size 20X50X1250mm made out off 1st class hardwood teak

S&F drawers as per drawing

S&F in replacement of Drawer lock along with duplicate key

Polishing to table office clerk with french polish to obtain smooth glossy finish.

S&F CP knob

TABLE CARD (FD-288) :-M&L for carry out repair and replacement of the following parts of table conference, removing carefully the existing unserviceable / damaged parts oftable conference and supply and fixed of new parts / componetns as per required size and shape to match with existing including re-assembling complete all shown in drg. and as directed by Engr -in Charge

S&F of table top of size 900x900mm made out of 18mm thick particle board aproveded make confirming to IS with 4mm thick teak wood edging all around the top all as shown in drg and as directed by Engr-in-Charge.

S&F leg of size 55X35X740 mm high made of 1st class hard wood teak

S&F rail of size 25X75X900 mm long made of 1st class hard wood teak

S&F drawer as per existing size and shape

S&F CP knob

S&F cloth bladge green 900X900 mm

S&F plastic rubber shoe white/black best quality as per existing size and shape

Apply one coat french polish to table card to obtain smooth, glossy finish including necessary preparation of surfaces.

HAT STAND WITH MIRROR (FD-233) : - Removing carefully the existing unserviceable/damaged parts of hat stand with mirror and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F Wooden battern 50X20X710 mm long

S&F Top ply 4mm thick oneside teak face as per existing size and shape

S&F Bottom ply 6 mm thick comercial ISI mark 1000X710 mm .Make National/Kit/Green ply

S&F Mirror 5mm thick 300X440 mm make Atul/Saint-Govin/Modi guard

S&F CP Peg

S&FTeak wood edging 35X6X3420 mm

S&F Key Plate

Apply one coat french polish to hat stand with mirror to obtain smooth, glossy finish including necessary preparation of surfaces.

TABLE OF SIZE 900 X 900 X 760MM (FD-291) : - M&L for carrying out repair and replacement of the following parts of table 900x900x760mm.Removing carefully the existing unserviceable/damaged parts of table 900x900x760mm and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of table top made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size 55 x 35 x 740mm high made out of 1st class HW (Teak).

S&F of rail of size 25 x 75 x 900mm long made out of 1st class HW (Teak).

S&F of triangular bracket (as support) made out of 2nd class HW (Teak) as per required shape & size.

Apply one coat french polish to table 900x900x760mm (3'x3') to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

PEG TABLE (FD-236 & FD-277) : - M&L for carrying out repair and replacement of the following parts of peg table.Removing carefully the existing unserviceable/damaged parts of peg table and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling of complete all as directed by Engr-in-charge

S&F of table top of size 450x300mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size 30 x 50 x 370mm high made out of 1st class HW (Teak) as per existing size & shape.

S&F of top long rail of size 20 x 40 x 450mm long made out of 1st class HW (Teak).

S&F of top short rail of size 20 x 40 x 300mm long made out of 1st class HW (Teak).

S&F in replacement of stiffiner 2 Nos. on bottom section to connecting legs in short side as per directed by Engr-in-Charge.

Apply one coat french polish to peg table to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

TABLE CENTRE (FD-235 & FD-274) : - M&L for carrying out repair and replacement of the following parts of table center.Removing carefully the existing unserviceable/damaged/boken parts of table centre and supply and fix of new parts/ components of required size and shape to match with the existing including re-assembling complete all as shown in drg and directed by Engr-in-charge

S&F of table top of size 900x450mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size 45 x 45mm at top and 30 x 30mm at bottom and 372mm high made out of 1st class HW (Teak).

S&F of long rail of size 40 x 19 x 900mm long made out of 1st class HW (Teak).

S&F of short rail of size 40 x 19 x 450mm long made out of 1st class HW (Teak).

Apply one coat french polish to table centre to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

TABLE OF SIZE 900 X 600 X 760MM WITHOUT DRAWER (FD-284) : - M&L for carrying out repair and replacement of the following parts of table 900x600x760mm ( 3X2') without drawer.Removing carefully the existing unserviceable/damaged parts of table 900x600x760mm without drawer and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of table top made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size 60 x 30 x 740mm high made out of 1st class HW (Teak).

S&F of long rail of size 20 x 60 x 900mm long made out of 1st class HW (Teak).

S&F of short rail of size 20 x 60 x 600mm long made out of 1st class HW (Teak).

S&F of stiffiner of size 25 x 40x 600mm long made out of 1st class HW (Teak).

Apply one coat french polish to table 900x600x760mm (3'x2') without drawer to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

TEAPOY (FD-278) : - M&L for carrying out repair and replacement of the following parts of teapoy. Removing carefully the existing unserviceable/damaged/broken parts of teapoy and supply and fix of new parts/ components of required size and shape as per drg to match with the existing including re-assembling complete all as directed by Engr-in-charge

S&F of tepoy top of size 600x450mm made out of 18/19mm thick ply wood BWR grade of approved make confirming to IS with 1mm thick laminated sheet at top and 4mm thick teak wood edging all around the top and bottom side of the top shall be painted with a coat of white primer all as shown in drg and as directed by Engr-in-Charge.

S&F of leg of size60 x 30 x 532mm high made out of 1st class HW (Teak).

S&F of long rail of size 20 x 60 x 600mm long made out of 1st class HW (Teak).

S&F of short rail frame of size 20 x 60 x 450mm long made out of 1st class HW (Teak).

Apply one coat french polish to teapoy to obtain smooth, glossy finish including necessary preparation of surfaces.

S&F plastic rubber shoe white/black best quality as per existing size and shape

STAFF UNIT FOR STAFF WORK STATION (1200 X750 X750MM) (FD/CCE/R&D/BLS/20) : M&L for carry out repair and replacement of the following parts of Jr staff table , removing carefully the existing unserviceable / damaged parts ofJR staff table and supply and fixed of new parts / componetns as per required size and shape to match with existing including re-assembling complete all shown in drg. and as directed by Engr -in Charge ,

S&F in replacement of Table top made out of 18/19mm thick plywood (BWR grade) with 1.01 mm thick plastic laminated shet on top , size 1200x 750mm with all around 4mm thick TW edging bottom side of the top shall be painted with a coat of white primer

S&F in replacement of Leg made out of 19mm thick particle board with one side decorative finish

S&F in replacement of Support of size 1160 x 460mm) made out of 19mm thick particle board with one side decorative finish

S&F drawer as per drawing

M&L Polishing to staff unit for staff work station with glossy finish by applying two coats of fench polisih including necessary pareparation of surfaces

S&F in replacement of Drawer lock along with duplicate key

TROLLY FOR TV (FD/E-6/MAP/04(R)) : M&L for carrying out repair,/replacement of the following parts and supply & fix of new parts as under of Trolly for TV of size as per drg

S&F Top of size 750x600mm made out of 18mm thick prelaminated particle baord with 4 mm thick edging all aroundm and all as directed by Engr-in-charge

S&F Back of size 650x650mm made out of 12 mmthick prelaminated particle baord and all as directed by Engr-in-charge

S&F Side of size 500x650 mm made out of 12 mmthick prelaminated particle baord and all as directed by Engr-in-charge

S&F shelves of size 500x610 mm made out of 12 mm thick prelaminated particle baord and all as directed by Engr-in-charge

S&F bottom of size 500x610 mm made out of 12 mm thick prelaminated particle baord and all as directed by Engr-in-charge

S&F Tray of size 600x500 mm made out of 19/18 mm thick prelaminated particle baord and all as directed by Engr-in-charge

S&F Shutter of size 610x310 mm made out of 12 mm thick prelaminated particle baord and all as directed by Engr-in-charge

S&F Telescopic channel for tray of size as per existing size and shape and all as directed by Engr-in-charge

S&F Auto closer hinges and all as directed by Engr-in-charge

S&F Swivel Type caster wheel 50 mm dia and all as directed by Engr-in-charge

S&F CP Handle 75mm long

TABLE DRESSING LADIES WITH STOOL (FD/MAP-II/07) : M&L for carrying out repair,/replacement of the following parts and supply & fix of new parts as under of Table dressing ladies with stool as per drg

S&F replacement of old defaced mirror of required size make(Modiguard/Saint gobain/Golden fish) duly fixed with frame of size 25x20 mm all around duly polished

S&F 6mm thick plywood fixed back of mirror.

S&F drawer as per required size and shape,side,front & back made out of 18 mm thick plywood having 6 mm thick plywood duly fixed at bottom.

S&F in replacement of old/broken side ply as per required size and shape made out of 18mm thick ply.

S&F in replacement of cushion 75mm thick (Sleep well/feather foam)duly covered with tapestry cloth as per required size and shape.

S&F in replacement table side partition(inner and outer)

S&F in replacement front shutter made out of 18mm thick laminated sheet

S&F in replacement 50mm long stainless steel handel fixed to drawer.

S&F in magnetic catcher fixed inside shutter as per required shape and size.

S&F in stainless steel piano hinges as per required shape and size.

S&F in replacement of bottom ply of existing size 12mm thick.

S&F in replacement of 75 mm long stainless steel handel fixed to shutter.

CHAIR DINING OFFICERS (FD/E6/MAP-II/04) : M&L for carrying out repair,/replacement of the following parts and supply & fix of new parts as under of Chair dining officers as per drg

S&F front leg of size 35x50x400mm made out of 1st class HW teak all as shown in drg.

S&F rear leg of size 35x50x960mm made out of 1st class HW teak all as shown in drg.

S&F front and rear rail of size 25x65x450 mm made out of 1st class HW teak all as shown in drg.

S&F side rail of size 25x65x460 mm made out of 1st class HW teak all as shown in drg.

S&F 15x30 mm size teak wood vertical strips made out of 1st class HW teak all as shown in drg.

S&F curved teakwood back rest of size 25x45mm

S&F high density cushion (Make Sleepwell/Feather foam) for seat of chair dining officer of required size duly covered with tapestray cloth

S&F in replacement of old/broken seat ply 12mm thick plywood as required size & shape Make(National/Kit/GSreen ply)

M&L Polishing to chair dining officers with glossy finish by applying two coats of fench polisih including necessary pareparation of surfaces

S&F hard rubber shoes white/black in colour of best quality as per existing shape and size

M/S T.N.CONSTRUCTION

ARIN AND COMPANY

RPL SYNDICATE CO

jlenterprise

Bidder Name

RPL SYNDICATE CO

M/S T.N.CONSTRUCTION

ARIN AND COMPANY

PREMIER HOOD HOUSE

jlenterprise