ADDN/ALTN TO TYPE IV MD ACCN BLDG NO. 72 TO 76 AT ARMAMENT COLONY GANESHKHIND PUNE

Amount

Surface excavation not exceeding deep but averaging 15 cm deep and getting out in hard /dense soil complete all as specified and directed .

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5metre in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, tubular poles or laying of pipes, or for removal / laying of cables etc., not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in hard/dense soil, including trimming sides of foundations and aforming bottom surface to required level, complete all as specified and directed.

Pre-cast cement concrete block masonry in PCC 1:3:6 tybe C1 using 20mm graded stone aggregate with solid blocks, exceeding 10 cm in width and setting in cement mortar complete built in CM 1:4, complete all as specified and directed.

PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed.

PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed.

75 mm thick cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in floor finished surface even and fair complete all as specified and directed.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and rurming rails and guides ,fixed with angle cleats or other connecting plates conforming to Fe-290 Gde E-165 complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet / trapezoidal steel sheet 0.50mm base metal thickness of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws and EPDM washers as specified, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm base metal thickness of any colour having tensile strength of 550 MPa as in ridges /roof covering/cladding to wall, fixed with self tapping screws and EPDM washers as specified, complete all as specified and directed.

Returning, filling in, in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25cm., complete all as specified and directed.

Removing surplus excavated soils to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5metre above the starting point, complete all as specified and directed.

Rendering 15 mm thick in two coats with 5 mm thick in cement mortar 1:4 as setting coat over 10mm thick cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth with out using extra cement using water proofing liquid (in top layer), as per manufacturers instructions, complete all as specified and as directed. Note: Supply only water proofing liquid will be measured and paid separately.

Prepraring newly plastered surfaces of wall and applying two coat of exterior emulsion paint (Weather proof) over a coat of primer at any height including necessary scafolding etc complete all as specified and as directed.

Taking down unsound and damaged /disressed plaster by dipping with utmost care to expose reinforcement ,cleaning the rusted reinforcement by rubbibg with wire brushes or emery paper and disposal of debris not exceeding 100 m distance complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed.

Seperating ,cleaning and scraping of reinforcement etc complete all as specified and directed. Note: The rusted/ defective reinforcement obtained from BOQ item NO 16 shall be measured

Mild steel TMT bars of grade Fe-500 of bars 10 mm dia and above cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

Mild steel TMT bars of grade Fe-500 of bars 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

Applying one coat of anti corrisive primer @0.25 lit/sqm for the steel area to exposed old and new reinforcement to the full circumfrance and length of bars to form unbroken 40 micron thick film complete all as specified and as directed.

Applying one coat of epoxy bonding agent @2.6 lit/sqm or as per manufacturees instructions to old concrete surfaces of columns ,beams ,chajjas and similar structural members complete all as specified and as directed.

Chicken wire mesh steel wire fabric not exceeding 5 kg per sqm fixed to concrete surface as in distressed concrete surfaces by means of nails etc complete all as specified and as directed.

Non shrink ,cementitious micro concrete mixed with 12.5mm graded stone aggregete using Renderoc RG of FOSROC or technocommercially equivalent in PIDILITE by weight( 18 kg agregate :25 kg Renderoc RG ) respectively as per manufacturer instructions laid in average thickness 50 to 100 mm in surface of columns ,beams ,chajjas and similar structural members including necessary water tight form work complete all as specified and as directed.

Spraying curing compound as per manufacturer's instructions on freshly casted concrete surface complete all as specified and as directed.Make: Concrete WB white or techno commerically equivalent in PIDILITE / M/s Bostik

Rendering 15mm thick in CM 1:4 on brick or concrete surfaces shall be provided in two coats viz 10mm first coat and 5 mm thick second coat using water proofing liquid as per manufacturers instructios finished and even and smooth with out using exta cement, complete all as specified and directed.

Rendering 10mm thick in CM 1:6 on internal wall of brick or concrete surfaces finished and even and smooth with out using exta cement, complete all as specified and directed.

Pressure guniting 30 to 70 mm thick in cement and sand in the ratio of 1:3 to effected area of RCC beams ,chajjas including necessary scaffolding for the height from ground to 15.0 m including 5 mm thick plastering in CM 1:4 with using water proofing compound @3% by weight of cement ,finished even and smooth without using extra cement complete all as specified and directed. Note: Supply only water proofing compound will be measured and paid separately.

Complete removal of existing treatment from surfaces of walls incuding pilasters, cornices etc., by scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots with wire brushes and removing existing loose particles etc., and applying two coats of weather-proof exterior emulsion paint over a coat of alkali resistant primer and finished even and smooth, complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the MD premises, complete all as specified and directed.

Demolition of cement concrete in floors not exceeding 150mm thick below & above ground level and removing out of site complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors ,aprons etc laid ,bedded and pointed in any mortar complete all as specified and directed.

Taking down & refixing in the same opening after necessary repairs of shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each complete all as specified and directed.

Providing 25 mm thick plain cement concrete 1:2:4 type B0 (12.5mm graded stone aggregate) as in sub base course and finished surface even and smooth without using extra cement complete all as specified and directed.

75mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection, laid in bays, bay area not exceeding 2sqm each, finishing the surface even and smooth without using extra cement including necessary formwork and filling the joints with mastic filling comprising 1 part of heated bitumen and 3 parts of sand (all by weight) complete all as specified and directed.

Forming Construction (Dummy) joint 75 mm deep x 10mm wide filled with sealing compound, Grade ‘A’, complete all as specified and directed.

Double charged fully Vitrified tiles, LIGHT colour 10 mm thick of size 600mm x 600mm polished in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles , laid over and including provision of 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

Double charged fully Vitrified tiles, LIGHT colour 10 mm thick of size 600mm x 100mm polished as in skirting set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles , laid over and including provision of 10mm thick rendering in CM 1:3 complete all as specified and directed.

Non - skid Ceramic coloured tiles (Grade B-IIa) of superior quality of size 300mmx300mmx 7 to 8 mm thick in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles , laid over and including provision of15mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed.

Glazed ceramic tiles (Grade B-IIa) of superior quality in vertical surfaces such as dado, 300 mm x 450 mm x 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed.

Machine cut Granite (of any type) stone slab of 18-20mm thick (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over and including provision of 15mm thick screed bed in CM 1:6 complete all as specified and directed. Note : Granite stone slab shall not be more than in two pieces in case of L-shaped cooking platform and in other cases, it should be in one piece only.

Machine cut kota stone flooring 20-25mm thick ( size not less than 560mmx560mm)over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including grinding and mirror polishing laid over and including provision of15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

Machine cut kota stone 15 -18 thick as in risers of steps ,skirting ,dado fixed over plaster and jointed with grey cement slurry mixed with pigment to match the shade of slab including grinding and mirror polishing laid over and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed.

18/19 mm thick Prelaminated particle board, exterior grade,prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with screws to timber framework complete all as specified and directed.(For kitchen cabinets/cupboards/shelves and similar works )

Taking down shutters of any description ( Cabinet and Cupboard shutters) area not exceeding 1.0sq.m each complete all as specified and directed.

Powder coated aluminium frame for windows with one or more rebates (Three track) including cleat for fixing etc complete all as specified and directed.

Powder coated three track aluminium sliding windows shutters ,aluminum sections weighing 0.55 kg/Sqm (Min) including necessary rollers ,clips ,locks ,jointing cleats ,rubber packing ,snap beading , glazing clips ,screws etc complete all as specified and directed.

Aluminium powder coated ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc complete all as specified and directed.

Aluminium powder coated ventilators shutters including frame without sash bars, almuiniun sections weighing 0.55 kg /m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws complete all as specified complete all as specified and directed.

4mm thick sheet glass, figured pin type glazing with oil putty insquare not exceeding 0.5 sq. m in each pane etc complete all as specified and directed.

4mm thick sheet glass, plain glazing with oil putty insquare not exceeding 0.5 sq. m in each pane etc complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Continous (piano) himges ,mild steel ,bright finish or electrogalvanised width of flaps 300 when opened complete all as specified and directed.

Extruded aluminium handles, fabricated type, anodised, 100mm long, complete all as specified and directed.

Ball catch spring with 8 mm di steel ball and brass body and striking plate including letting in complete all as specified and directed.

Taking down chowkats or frames with shutters including grills (without taking off shutters from the frames), area not exceeding 1.5sq.m each complete all as specified and directed.

Taking down chowkats or frames with shutters including grills (without taking off shutters from the frames), area exceeding 1.5sq.m each but not exceeding 4.0sq.m each, complete all as specified and directed.

Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats (Minimum weight 300gms) including taking down existing one complete all as specified and directed.

Towel rail 600 mm long brass Chromium plated 20 mm dia D type fixed to wall etc including taking down existing one complete all as specified and directed.

Complete removal of existing treatment on surfaces of walls by scraping with wire brushes, washing down with water and applying two coats of water based distemper (acrylic emulsion distemper ) over a coat of alkali resistant primer over two coats of internal grade wall care putty 1.5mm thick( total thickness of two coats shall not be less than 1.50mm) finished even and smooth as per manufactrer's instructions at any height including necessary scafolding etc. complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of water based distemper (acrylic emulsion distemper ) over a coat of alkali resistant primer over two coats of internal grade wall care putty 1.5mm thick (total thickness of two coats shall not be less than 1.50mm) finished even and smooth as per manufactrer's instructions at any height including necessary scafolding etc. complete all as specified and directed.

Preparation of old decorated surfaces of celing by brooming down or steel wire brushing ,scraping down smoke ,moss and efflorescent salts and treating oil and greasy spots etc and applying two coats of white washing complete all as specified and directed.

Preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

Taking up or down steel tubing and connections, 15mm bore, complete all as specified and directed.

Taking up or down steel tubing and connections, 20 mm bore, complete all as specified and directed.

Galvanised Steel water tubing of 15 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing and including making good to match with the existing surface complete all as specified and as directed.

Refixing old Galvanised Steel water tubing of 15 mm bore and connections in new or old position fixed to walls, ceiling or laid on floors including testing and including making good to match with the existing surface complete all as specified and as directed.

Galvanised Steel water tubing of 20 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing and including making good to match with the existing surface complete all as specified and as directed.

Refixing old Galvanised Steel water tubing of 20 mm bore and connections in new or old position fixed to walls, ceiling or laid on floors including testing and including making good to match with the existing surface complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000 litre capacity (ISI embossed), double layered, hoisted and fixed in position all as specified in SSR Part I and including taking down existing water tanks any type complete all as specified and directed.

20 mm dia bore Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed.minimum weight 210gms complete including taking down existing ball valve any type complete all as specified and directed.

20 mm bore Gun metal, globe or gate valves with iron wheel head, ISI Marked screwed both ends for iron/GI pipe and fixed including taking down existing gate valve complete all as specified.

Bib taps, cast copper alloy, fancy type, chromium plated, long body with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule , 15mm bore, with CP flange, including taking down old bib tap of any dia, complete all as specified and directed.(Minimum weight 550grams per each)

75 mm bore UPVC (SWR) multi floor trap / nahni trap, plain / single hole chromium plated grating including jointing to waste pipe with solvent cement, fixed in PCC 1:2:4 type B1 including taking down existing floor trap complete all as specified and directed.

Vitreous china squatting pan 'Orissa" pattern, size 580x440mm white, integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti-syphonage pipe, WC pan shall be set in lean concrete below level of rim of pan to receive the floor finish etc complete and including taking down existing unserviceble one complete all as specified and as directed

Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., with and including provision of seat cover black closed pattern with flat bottom with mild steel CP hinging device including taking down existing unserviceble one complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets, jointing with existing 32mm dia flush pipe and connections to pipes and fixing of chain and pull, or lever, taking down existing unserviceble one complete all as specified and directed.

Wash hand basin, Vitreous China , first quality, white colour, of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand, with and including GI brackets, 32mm bore CP waste coupling (half or full threaded ) including taking down existing items complete all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, 15mm bore, including taking down old pillar tap of any dia, complete all as specified and directed.

Stop valves, cast copper alloy, fancy type, chromium plated (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, 15mm bore, including taking down unserviceable stop valve of any size, complete all as specified and directed.

Stop valves, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, 15mm bore, including taking down unserviceable stop valve of any size, complete all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 450mm, both ends having brass coupling nut and PVC washers, complete all as specified and directed.

Brass chromium plated swivel shower rose 95mm dia with shower arm 15mm bore ,195 mm long with bend 45 º with flange , including fixing to steel pipe or union, including taking down unserviceable shower of any size, complete all as specified and directed.

LDPE pipe 32mm bore of presuure rating 6kgs /sqcm fixed to walls ,ceiling or in floors complete all as specified and as directed.

LDPE pipe 40mm bore of presuure rating 6kgs /sqcm fixed to walls ,ceiling or in floors complete all as specified and as directed.

Chromium plated toilet paper holder including taking down existing one complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern),including all fittings heads, shoes, bends, swan-necks etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with and including provision of suitable size of PVC clamps complete all as specified and directed.

110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with and including provision of suitable size of PVC clamps complete all as specified and directed.

UPVC (SWR) bends any radius, 75mm bore with access door complete all as specified and directed.

UPVC (SWR) bends any radius, 110mm bore with access door complete all as specified and directed.

75mm bore UPVC (SWR) branch piece single (single 'T' ) equal or unequal, with access door, complete all as specified and directed.

110mm bore UPVC (SWR) branch piece single (single 'T' ) equal or unequal, with access door, complete all as specified and directed.

UPVC (SWR) vent cowl, 75mm bore, complete all as specified and directed.

Kitchen stainless plate rack of size 1200x900mm ,1 mm thick complete all as specified and directed.

Sinks with drainage board made of stainless steel 1.00mm thick kitchen with plugs, washers and wastes; including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, fixed in repairs including 40mm bore CP waste coupling (half or full threaded ) one complete all as specified and directed.

Taking down shutters of any description exceeding 1.0sq.m but not exceeding 2.0sq.m each complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification, with and including making good to jambs with CM 1:4 and finished the surface to match with the existing, complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified and directed.

Pressed steel frames of size 125mm x 60mm x 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Second class hardwood plain, framed, panelled shutters (two number of panels), 35mm thick, factory made, with lock rail and panels of 12mm thick veneered particle board medium density with commercial veneering on both faces : supplied and fitted to chowkats; The size of rail and styles shall be all as per IS : 1003 (Part - I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

Second class hardwood Glazed and skeleton shutters, 35mm thick, factory made, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified and directed.

35mm thick factory made flush shutters ,solid core construction with block board core and plywood face panels and commercial decorative veneerig on both sides complete all as specified and directed.

Butt hinges 100mm size extruded aluminium alloy with galvanised mild steel hinge pin ,anodised type B-21 complete all as specified and directed.

300mm long Aluminium alloy, anodised, sliding door bolt, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixed, complete all as specified and directed.

Extruded aluminium handles, fabricated type, anodised, 150mm long, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section and fixed, 150mm long, complete all as specified and directed.

Aluminium door stopper of size 60 to 75 mm long double legged fixed to bottom rail of door shutter provided with rubber bushing at one end to stop the door at floor and other end provided with aluminium plate base fixed with door shutter with screws at appropriate height complete all as specified and directed.

PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in pressed steel door frames complete all as specified and directed.

PCC 1:2:4 type B 1 using 20 mm graded stone aggregate as in bed blocks including use and waste of form work complete all as specified and as directed.

Treating small articles such as hold fasts with tar or coal tar ,black paint including preparation complete all as specified and as directed.

300mm ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and directed. Makes : Fosroc/Dr Fixit/Pidilite/Sika

Applying acrylic cementicious polymer modified elastomeric waterproofing & protective coating like brush bond of Fosroc or Pidifin 2K(Pidilite) on floors and walls as per manufacturer instructions over and including 15 mm thick rendering on fair face of concrete surfaces in CM 1:4 in sunken portion (sides and floors) mixed with water proofing liquid and finishing the surface even and smooth with out using exta cement, complete all as specified and directed. NOTE:- Water proofing liquid shall be measured and paid separately under respective item of this Schedule.

PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sunken portion complete all as specified and directed.

25 mm dia GI pipe light grade as in spout pipe in sunken complete all as specified and directed.

Tubular drapery rods ornamental type for curtains, powder coated aluminium 25mm dia including taking down unserviceable curtain rod of any size, complete all as specified and directed.

Mild steel pre-painted brackets suitable to hold the drapery rods with sofio phenol (Latto) suitable to drapery rod of 25mmdia decorative type with suitable adhesive complete all as specified and directed.

Preparation of new or previously untreated surfaces wood and wood based materials, of any description, not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

125 mm size hasp and staple aluminium anodised including bolt to hinge plate complete all as specified and directed.

UPVC(SWR) gully traps 125/110 mm setting and jointing with solvent cement including taking down existing unserviceable gully trap of any type, complete all as specified and directed.

Forming V grooves in plaster n exc 10mm deep and n exc 10 mm on face and flush pointing in CM 1:3 to grooves portion matching to existing plaster complete all as specified and directed.

Framed work such as ornamental type grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Preparation of new or previously untreated steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

100mm size Butt hinges in repairs medium weight cold rolled mild steel complete all as specified and directed.

Extruded aluminium handles, fabricated type, anodised, 150mm long, in repairs complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section and fixed, 150mm long in repairs complete all as specified and directed.

300mm long Aluminium alloy, anodised, sliding door bolt, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixed in repairs complete all as specified and directed.

Two way Bib taps, cast copper alloy, fancy type, chromium plated, long body with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule , 15mm bore, with CP flange, including taking down old bib tap of any dia, complete all as specified and directed.

Health faucet, chromium plated, fancy type, brass body with 1.2metre length stainless steel braided rubber hose pipe and wall hook, fixed in position to wall, complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including taking down existing wire mesh complete all as specified and directed.

Brass chromium plated 3 in 1 mixture valve , fancy type 15 mm bore min weight 950 grams complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, complete all as specified and directed.

Rendering 10mm thick in CM 1:6 as in dubbing coat on stone walls complete all as specified and directed.

Rendering 5mm thick in CM 1:6 on dubbing coat of brick work or stone surfaces and finishing the surface even and smooth with out using exta cement, complete all as specified and directed.

Glossy finished 60 mm thick machine pressed precast conctete interlocking paver block any shape and size, with grey cement and pigment, confirming to IS 15658-2006 -M-35 Grade complete all as specified and directed. Make as approved by GE.

75 mm thick Plain cement concrete 1:4:8 type D2 40mm graded stone aggregate as insubbase/levelling course complete all as specified and directed.

50 mm thick crushed stone sand /M-sand in cushioning for interlocking tiles complete complete all as specified and directed.

Demolition & breaking up any drains pipes 150mm bore complete all as specified and directed.

Demolition of brick / concrete block masonry /stone masonry, built in cement mortar including all quoins, arches, pillars, etc, excluding ashlar facings, dressed stonework complete all as specified and directed.

Concrete bed to drain pipes of 150mm bore, using cement concrete 1:3:6 type C2 using 40mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed.

150mm bore of Reinforced Concrete Pipes class NP-2 laid in trenches and jointed in CM (1:1) with collars complete all as specified and directed.

Brick work with fly ash old size bricks straight or curved on plan exceeding 6metre mean radius built in CM 1:4, complete all as specified and directed.

Precast reinforced cement concrete 1:2:4 type B1 using 20mm grded stone aggregate as in cover slabs (for man holes etc), with plain fair faces, including chamfers, weatherings, throating etc. and setting in CM 1:4 complete with joints to match, complete all as specified and directed. (Note: Reinforcement shall be measured and paid for separately under relevant item).

Rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces and finishing the surface even and smooth with out using exta cement, complete all as specified and directed.

PCC 1:2:4 type B2 using 40mm graded stone aggregate as in surface channels and drains and making the surface even and smooth with out using cement and including necessary form work complete all as specified and directed.

Extra for forming fair finished drain or channel 30 CM inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/ stopped ends etc complete all as specified and as directed.

PCC 1:2:4 type B 1 using 20 mm graded stone aggregate as in coping including weathering, slightly rounded or chamfered angles and throating including use and waste of form work complete all as specified and as directed.

Demolition of Cement Concrete reinforced of any position complete all as specified and directed.

Mild Steel work in tubular trusses and similar circular or rectangular sections including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161- 1979 grade St.-240 complete all as specified and directed.

Mild steel bolts exc 12 mm dia but not exc 20mm dia purpose made with hexagonal or square head one end and screwed the other, or screwed both ends,each screwed and to be fitted with washers and one hexagonal square nut , not exc 30cm long complete all as specified and directed.

Mild steel Plates for base plates and gusset plates plain or chequered complete all as specified and directed.

RCC M25 (Design mix) using 20mm graded stone aggregate as in footings, foundations, including rafts ,footings ,foundation beams ,plinth beams ,bases for columns and columns etc complete all as specified and directed.

Formwork for rough finished flat sides of concrete foundations, footings, columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; pile caps, grade beams and similar work; vertical or to batter, complete all as specified and directed.

Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc, complete all as specified and directed.

Taking down carefully by unscrewing fittings and fixtures ,ceiling fittings ,bulk head fittings ,tube light fittings etc from boards /out let boxes complete all as specified and directed.

Taking down carefully DBs any type any size, two pin and earth plug etc all as specified and making good to the disturbed surfaces to match with the existing complete all as specified and directed.

Taking down ceiling fans of 1200/1400mm sweep / Exgaust fans and painting with one coat of synthetic enamel paint and refixing the same after completion of civil works complete all as specified and directed.

Taking down carefully electric energy meter by disconnecting the electric cable and securing the live lines properly and depositing to AGE E/M store yard complete all as specified and directed.

Taking down carefully sub main wiring of any size including conduit and making good disturbed surfaces of walls /ceiling etc complete all as specified and directed.

Taking down carefully electric geyser and refixing the same after completion of civil works complete all as specified and directed.

Point wiring complete with 1.5 sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor 1100 Volts grade, ISI marked, drawn through in and including 20mm dia rigid PVC conduit medium grade and conduit accessories, concealed in stone / brick masonry walls, roofs, floors etc, by means of saddles and clips etc, including provision of cast iron /pressed steel terminal box of suitable sizes and 1.6mmm thick duly painted both side by anti corrosive paint ,with plasic laminated sheet cover 3mm thick with brass screw ,cup washer for mounting switches, sockets, regulators etc., including 1.5sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly, complete all as specified and directed for one light point on independent board, complete all as specified and directed. NOTE: (i) The quoted rate shall deemed to include the cost of metal flush boxes, cover plate, provision of blank plates as per requirement etc. (ii) Quoted rate shall also deemed to include cost of making necessary chases in walls for inserting metal boxes and making good the disturbed surfaces to match with existing

All as per Sl. Item No. 161 here-in-before for bell point complete all as specified and directed.

All as per Sl. Item No. 161 here-in-before for fan/exhaust point complete all as specified and directed.

All as per Sl. Item No. 161 here-in-before but for one 3-pin 6Amp socket outlet point on independent board controlled by one one-way 6Amp switch, complete all as specified and directed.

All as per Sl. Item No. 161 here-in-before but for one 3-pin 6Amp socket outlet point on same board controlled by one one-way 6Amp switch, complete all as specified and directed.

All as per Sl. Item No. 161 here-in-before controlled by 2 Nos two way switches complete all as specified and directed.

Point wiring complete with 2.5 sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor 1100 Volts grade, ISI marked, drawn through in and including 20mm dia rigid PVC conduit medium grade and conduit accessories, concealed in stone / brick masonry walls, roofs, floors etc, by means of saddles and clips etc, including provision of cast iron /pressed steel terminal box of suitable sizes and 1.6mmm thick duly painted both side by anti corrosive paint ,with plasic laminated sheet cover 3mm thick with brass screw ,cup washer for mounting switches, sockets, regulators etc., including 2.5sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly, complete all as specified and directed for 3-pin 15/16 Amp socket outlet point on independent board, complete all as specified and directed. NOTE: (i) The quoted rate shall deemed to include the cost of metal flush boxes, modular white cover plate, provision of blank plates as per requirement etc. (ii) Quoted rate shall also deemed to include cost of making necessary chases in walls for inserting metal boxes and making good the disturbed surfaces to match with existing

Switch piano flush type 6 Amp, one way, single pole 240V, complete all as specified and directed.

Switch piano flush type 6 Amp, two way, single pole 240V, complete all as specified and directed.

Ceiling rose three terminal surface bakelite type AC 50 Hz 230V, complete all as specified and directed.

Angular holder bakelite insulated body complete all as specified and directed.

Socket socket combination 2 in 1 ,5-pin, 6Amp, multi-purpose type, 240V, complete all as specified and directed.

Switch socket combination 5 and 16 Amp multipurpose complete all as specified and directed.

Step type fan regulator, 2 Module 230Volts ,120 watt complete all as specified and directed.

Bell push button flush type 5 Amps complete all as specified and directed.

Bell ding dong AC 230 Volts single phase complete all as specified and directed.

Sub main wiring complete with 2 runs of single core 6 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawn through and including provision of non-metallic rigid PVC conduit 20mm dia and its accessories concealed in brick masonry walls etc in and including cutting& chasing and making good the surface to match the existing and connecting terminal ends to DB's including providing 1 run of single core 6 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly, including taking down old sub main wiring of any type and any size complete all as specified and directed. NOTE:- (i) Two runs of 6sq.mm copper conductor, One run of 6.0 sq.mm copper earth continuity conductor and one run of PVC conduit shall be measured as one unit length. (ii) The rate quoted per unit shall be deemed to be inclusive of the extra length of cable /wire required for connection to MCCBs .

Sheet metal enclosure with three pole and neutral with 3 pin and earth plug and socket complete with one triple pole MCB 20/32 Amps 415 volts A/C and 32 Amps industrial plug top including taking down existing one complete all as specified and directed .

Sub main wiring complete with 2 runs of single core 4 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawn through and including provision of non-metallic rigid PVC conduit 20mm dia and its accessories oncealed in brick masonry walls etc in and including cutting& chasing and making good the surface to match the existing and connecting terminal ends to DB's including providing 1 run of single core 4sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly, including taking down old sub main wiring of any type and any size complete all as specified and directed. NOTE:- (i) Two runs of 4 sq.mm copper conductor, One run of 4.0 sq.mm copper earth continuity conductor and one run of PVC conduit shall be measured as one unit length. (ii) The rate quoted per unit shall be deemed to be inclusive of the extra length of cable /wire required for connection to MCCBs .

LED tube light fitting 20W ,4 feet long wall mounted anodized aluminium extruded heat shrink provided for efficient heat deception and interchargeable integrated electronic driver luminaries LED as light sources housing complete with all accessories including suitable tube 20 W internally prewired and including with twin core twisted flexible copper cable of suitable size including taking down existing one complete all as specified and directed . Make:Havells Cat No: LUMILINEBS20WLED865SPCWH or Techno commercially equivalent make in Philips/Crompton Greaves

LED tube light fitting 9W ,2 feet long wall mounted anodized aluminium extruded heat shrink provided for efficient heat deception and interchargeable integrated electronic driver luminaries LED as light sources housing complete with all accessories including suitable tube 9 W internally prewired and including with twin core twisted flexible copper cable of suitable size including taking down existing one complete all as specified and directed . Make:Havells Cat No: LUMILINEBS9WLED865SPCWH or Techno commercially equivalent make in Philips/Crompton Greaves

LED surface mounted square panel aluminium die cast body of 12 W complete with all accessories including twin core twisted flexible copper cable of suitable size complete all as specified and directed. Make:- Havells Cat No ENDGEORIRDDLR12WLED857S or techno- commercially equivalent model of Philips /Crompton Greaves

LED Slim surface / wall mounted decorative ovel bulkhead fitting suitable light of 10 watts complete with all accessories including twin core twisted flexible copper cable of suitable size complete all as specified and directed Make:- Havells Cat No HEXAF10WLED857SSYMBOPC or techno- commercially equivalent model of Philips /Crompton Greaves

LED Lamp ball type suitable for lamp holder of 10W complete all as specified and directed Make: Havells/Philips/Crompton Greaves/Bajaj

MCB DB SPN double door 12-way sheet metal enclosure with category of protection IP-42, 240V, with tinned copper 200Amp rated bus bar suitable for MCBs, complete all as specified and directed. Note: All incomimg /out going MCBs shall be measured and paid under appropriate item .

MCB DB SPN double door 4-way sheet metal enclosure with category of protection IP-42, 240V, with tinned copper 200Amp rated bus bar suitable for MCBs, complete all as specified and directed. Note: All incomimg /out going MCBs shall be measured and paid under appropriate item .

MCB TP 440 V 63 Amps complete all as specified and directed

MCB SPN 16 to 32 Amp, 240 Volt, 'C' curve, 10KA breaking capacity including taking down existing one complete all as specified and directed.

MCB DB Verical double door TPN 4way IP 43 ,415 volt AC made up of powder coated MS Sheet steel enclosure in and including MCCB FP 100 Amp ICS=50% Icu 16KA with OL&SC setting including taking down existing one complete all as specified and directed.Make: Cat Part No.DHDLVDWGOF004 of Havells or Techno commercially equivalent in LEGRAND/ABB

MCB SP 6 to 32 Amp , 240 Volt, 'C' curve, 10KA breaking capacity, including taking down existing one complete all as specified and directed.

Earthing provided in replacement complete with GI earth plate electrode 600mm x 600mm x 6.0 mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth wire of 4mm dia by means of bolts, nuts, washers of galvanised iron or steel, GI earth wire shall be protected by 15mm dia GI pipe 'medium grade', watering pipe 20mm dia GI pipe 'light grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL, and connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 50mm thick RCC cover (1:2:4) type B1 mix with 8mm dia nominal reinforcement @ 75mm c/c both ways etc complete all as shown in electrical plate No.3 connected to earthing test point, including testing on completion, complete all as speciified and as directed. NOTE:- (a) Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. (b) Earth continuity conductor beyond 7.5metre shall be measured and paid under respective item of this Schedule.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed.

AC single phase static energy meter of accuracy class 1.0,240 V 50Hz with backlit 1P LCD display of rating 5 -30 A (measures and display KWH ,V ,Current I ,KW ,pf last month history of KWH,MD in KW) with special features like TOD ,temper logging ,optical communication port display in absence of power with optical port and transparent hinge type box complete all as specified and directed.Make: Cat No WM101BC5DDHBOX of L&T

Heavy duty exhaust fan 300mm sweep ,900RPM with aluminium louvers and shutters suitable for 240V single phase AC supply with all fixing arrangments to fix on wall, including provision of copper bunched flexible three core 1.5sq.mm PVC insulated cable from connection point to fan, complete all as specified and directed.

Test point consisting of terminal box, drilled and screwed with 22 swg GI cover including 2 Nos 12mm dia 25mm long hexagonal head screws jointing GI and aluminium strips with bolts, nuts and washers on and including jointing plate made of gun metal or phosphor bronze of size 75x75x25mm complete enclosure/terminal block assembly grouted in wall at 600 mm height from the length protection level by means of two nos 40x40x5mm MS plate with 6mm dia anchored bolts embedded in wall including nuts and washers all as specified and directed .

Earthing complete with GI earth plate electrode 600mm x 600mm x 6.0mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth strip of size 25mm x 4mm by means of bolts, nuts, washers of galvanised iron or steel, GI earth strip shall be protected by 40mm dia GI pipe 'medium grade', watering pipe 20mm dia GI pipe 'medium grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL, and connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 50mm thick RCC cover (1:2:4) type B1 mix with 8mm dia nominal reinforcement @ 75mm c/c both ways etc complete all as shown in electrical plate No.3 connected to earthing test point, including testing on completion, complete all as speciified and as directed. NOTE:-1 Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. 2. GI strip above 7.5m will be measured and paid seperately

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required of size 25mm x 4mm galvanised iron strip, complete all as specified and directed.

Single pointed air termination aluminium rod 12mm dia 300mm long and including 40mm dia GI Medium grade support pipe 600mm long, 25x6mm MS flat iron clamps, bolts/nuts and washers etc lower end of pipe fitted in a 40mm dia GI socket screwed and welded on and including MS base plate of size 300x300x6mm thick grouted on top surface of the wall with 4 Nos 12mm dia regged MS bolts/nuts washer etc on GI pipe secured firmly laterally on the wall surface in a vertical manner by means of rugged bolts grouted on the walls including nuts and washers etc upper end of pipe duly plugged lower end of Air termination rod duly jointed/welded with down/ horizontal conductor complete all as specified and directed .

Aluminium strip 25mmx3mm complete with saddles and fixing screws for fitting the strip complete all as specified and directed .

Pre-cast cement concrete block masonry with solid blocks exceeding 10CM in width using PCC 1:3:6 type tybe C1 using 20mm graded stone aggregate and setting in CM 1:4, complete all as specified and directed.

Cement concrete block of size 150x150x150 mm in PCC 1:3:6 type tybe C1 using 20mm graded stone aggregate for fixing on roof conductor /air terminal rod /GI strip etc including necessary form work including taking out PCC block complete all as specified and directed.

Epoxy base insulator suitable size 35 mm height fixed on PCC blocks/ on wall on MS angle /on towers with and including nut bolts and washers etc including taking down existing one complete all as specified and directed.

Supply & Laying, connecting, testing & Commissioning UG cable LT XLPE insulated, earthed, screened, PVC bedded, galvanised steel strip or wire armoured , electrical power cable heavy duty confirming to IS 7098 (Part II) with stranded aluminum conductor 1100 volts grade of size 4 core25 sqmm including taking down the existing unserviceable cable complete all as specified and as directed. NOTE :- Excavation, earthwork & cable protection measured separately.

Supply & Laying, connecting, testing & Commissioning UG cable LT XLPE insulated, earthed, screened, PVC bedded, galvanised steel strip or wire armoured , electrical power cable heavy duty confirming to IS 7098 (Part II) with stranded aluminum conductor 1100 volts grade of size 2 core 10sqmm including taking down the existing unserviceable cable complete all as specified and as directed. NOTE :- Excavation, earthwork & cable protection measured separately.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5metre in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, tubular poles or laying of pipes, or for removal / laying of cables etc., not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in soft /loose soil, including trimming sides of foundations and aforming bottom surface to required level, complete all as specified and directed.

Spreading of crushed stone dust/M-sand in trenches for cable protection, complete all as specified and directed. NOTE:- Punned thickness shall only be measured and paid.

Supply and laying common burnt clay Bricks class 'B' designation 75 old size 230mm x 115mm x 75mm in trenches for cable protection, complete all as specified and directed.

Galvanized iron tubing light grade of the size 40mm dia for protection of cable under road, floors etc complete all as specified and directed.

Cutting of roads /plinth for removal /laying of pipe and making good the disturbed surfaces as per adjoining surfaces complete all as specified and directed.

PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in filling and mass concre for making good road /foot path /hard standing /drain /plinth protection complete all as specified and directed.

L.K.R.TIWARI CONSTRUCTION

KARNI BUILDERS

shah construction

VIRENDRA FABRICATORS

agarwal and company