Widening of Existing road with CC and Interlocking tiles, Resurfacing of 3.0m existing road and Construction of RCC drain at Tilapta Karanwas to Bhuda Khodna road, Greater Noida.

Earth work in cutting or in embankment in ordinary soil excavation to be in the from of regular pits not exceeding 0.50M in depth and earth work in embankment to be in 20 cm. layers including remming and dressing the surface to required levels and slopes and also including 1.50 M lift and 30M lead. The earth from cutting to be used in making embankment or to be deposited as spoil banks with in 30M. distance as directed by the Engineer in charge excluding Royallity. Wherever applicable for small work of Abadi area. (Where machine can not reach/move) SOR-20/253(a)/4.03)

Cartage of earth or fly ash when added to schedule item no. 253 : 1st Km. (if lead is beyond ½ Km) SOR-20/261(b))

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. (DSR-18/16.1)

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.(DSR-18/11.2)

Granular sub-base with graded material, plant mix method Construction of granular sub-base by providing close graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401. MORTH/4.01/401(A)

PCC Grade M-25 using batching plant transit mixture and manual placing (MORTH-20/9.06/D/Case-II)

Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade ‘A’ sealing compound. (DSR-18/16.46.1)

Providing and applying tack coat with bitumen grade of VG-10 using pressure distributor at the rate of 0.50 Kg per sqm on the prepared bituminous surface cleaned with mechanical broom. (MORTH 5.02/503)

Providing and laying Bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @5.40 Percent of mix and filler transporting the hot mix to work site, laying with hydrostatic paver finisher with sensor control to the required grade, level, and alignment rolling with smooth, wheeled vibratory and tandem rollers to achive the desired compaction as per MORTH specification clause No 507 complete in all respects. (MORTH/5.05/507(B))

30mm compacted thickness with bitumen penetration of [email protected]% by weight of total mix. (MORTH-5.05/507(B))

Providing and laying I Shaped Interlocking tiles Rubber moulded 80mm thick precast cement concrete having plan dimension 200x(160+120mm) with compressive strength not be less than 40Mpa (M-40) and weight 5kg, laid in required pattern over and including averege 50mm Thick Compacted bed fine sand and filling the joints with fine sand all complete as per direction of engineer-in-charge with conforming to ISI-15658-2006 SOR/A.R. Grey colour.

Excavation in foundation in ordinary soil (Loam clay or sand) including lift upto 1.50 M and lead upto 30.00M and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer incharge upto a distance of 30m from the foundation trenches (where machine con not reach/move) (SOR/251 (A)/4.1.1)

Depth from 0.0 to 1.5M below G.L.

Cartage of earth or fly ash when added to schedule item no. 253 : 1st Km. (if lead is beyond ½ Km) SOR-20/261(b))

Cement concrete with 4cm gauge Approved stone ballast coarse sand & cement in the proportion of 8:4:1 including supply of all materials labour tools & Plants etc required for proper completion of the work

8:4:1 (1 Cement 4: Coarse sand :8 graded stone aggregate 40mm nominal size) (SOR-20/281/5.08)

Plain/Reinforced Cement concrete in open foundation complete as per Drawing and Technical Specifications. (MORTH-20/9.06/E/Case-II)

RCC Grade M-25 using batching plant transit mixture and manual placing (MORTH-20/9.06/E/Case-II)

Steel reinforcement for RCC work including straightening cutting bending placing in position and binding all complete upto plinth level

Thermo Mechanically treated bars of grade Fe-500D or more. (SAIL Steel) (DSR-18/5.22.6/AR)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (DSR-18/10.25)

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. (DSR-18/10.25.2)

Labour cess and GST will be paid extra as per Govt. orders.

Please Enable Macros to View BoQ information