Civil, Interior, Electrical, Networking and Miscellaneous works for CT Simulator at TMH

Amount

DISMANTLING & DEMOLISHING Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking as per the direction of EIC.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material as per direction of Engineer-in-charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking materialdisposal of as per instracted of EIC.

Dismantling aluminium/ Gypsum partitions, and false ceiling including disposal of unserviceable material and stacking of serviceable material as directed by Engineer-in-charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. Quoted Rate for Fully loaded Truck

BRICK WORK / WALL PARTITION Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

DOOR / WINDOW WORKS (WOODEN & ALUMINIUM) Providing and fixing flush door shutters commercial type, thickness suitable to take lead sheet load core of block board construction with frame of 1st class hard wood & comm. Ply & 1mm thk. laminate on both faces of shutters with 6mm TW lipping all around with SS butt hinges and necessary screws etc. complete including seasoned Mirandi wood frames of approved section fixed with iron hold fasts and wooden moulding all around all hardware included i.e. Handles, Tower bolt, locks, Door closer stopper etc Providing wood work C.P teak wood in frames for doors wrought framed and fixed in position including applying one coat of approved wood primer to the exposed surface of wood in contact with masonry/ concrete etc. complete.

1200x2100 (with 2mm lead sheet lining shutter & frame complete)

1000x2100 (with 2mm lead sheet lining shutter & frame complete)

1000x800mm (lead lined Window frame only)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer in charge. Pre-laminated particle board with decorative lamination on both sides

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. With twin rubber stopper

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing PTMT Butt hinges with necessary screws etc. complete.100x75x10 mm fitted with 5.5 mm dia MS Bright Bar Rod weighing not less than 53 gms

Providing and fixing PTMT Tower Bolts with 12 mm one piece rod inside and necessary screws etc., complete. 202x42x18 mm weighing not less than 78 gms

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

FLOORING Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including handding & grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm

Protective of Floor with POP (plaster of paris) of minimum 10mm thick with polythene paper covering and maintaining the POP and till completion of work.

FALSE CEILING Providing and fixing of false ceiling at all heights of 600mmx600mmx12mm armstrong metal ceiling tiles of type Metalworks Clips-on laid on armstrong prelude XL exposed grid systems with 9mm wide T Section flanges colour white. The frame work comprise of main runner spaced at 1200mm centers securely fixed to the structural soffit approved hangers at 1200mm maximum centers. Hangers (GI wire) to be fixed by approved roof plug and screws etc. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall. flush fitting 1200mm along cross tees (with double stitching) to be interlocked between main runners at 600mm c/ c to form 1200x600mm modules. Cut cross tees longer than 600mm to be supported independently. 600mmx600mm modules to be formed by fittings 600mm long flush fitting cross tees centrally between the 1200mm cross tees. Perimeter trim to be armstrong wall angle secured to walls at 450mm maximum centers.

FINISHING WORKS 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand)

Plastering on vertical face of the wall using mortar (Cement: Sand=1:6) admixed with Dr.Fixit Pidiproof LW+ 101 liquid, @ 200 ml per 50 Kg of cement.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Providing and placing in position Trench under the floor level with conc. surrounds and bends as required.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Furniture Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. melamine point shed 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. melamine point shed 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebet in flush door shutter (Total area of the shutter to be measured)

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 75 mm

Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete.

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 75 mm

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer in charge

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 25 mm dia

Supply & Installation of Cubicle/ Privacy Curtains for Hospital Services (Make : RD Plast)

ELECTRICAL Dismantling / Removing Existing light fittings in areas and handing over the same to the concerned authorities

DISTRIBUTION BOARDS Surface mounting MCB DBs conforming to the specification fabricated out of 1.2mm thick CRCA sheetsteel enclosure and powder coated to RAL-7032,complete with cable gland plate with knockouts at the top, bottom and sides and provided with hinged covers. The DBs shall have insulated fork typephase bus bars insulated earth bus. Independent neutralbus bar for each phase and interconnecting wiring. (Cost of MCBs/ELCB/RCBO 6Amp to 32Amp rating etc. as per SLD to be included). All the DB's shall be universal mounting type with cable ties for cable management and top/Bottom removable gland plates withknockouts, MCB DB's suitable for TP/4P MCB as a Incomer and SP/DP/TP/TPN MCB's as outgoings with Separate Neutral Bus bars and Common earth Bus and Insulated bus bars and interconnecting wiring etc. the incoming bus bars shall 100A rating.

Ltg & RP & AC DB -8 way phase segregated TPN DB with 63Amp TPN incomer MCB. The price shall include all the incoming and out goings (6Amp to 25Amps SP MCBs), 3 nos. 63Amps DP RCCBs and Bus bars and other accessories

UPS DB - 6 way phase segregated TPN DB with 40Amp TPN incomer MCB. The price shall include all the incoming and out goings (6Amp to 25Amps SP MCBs), 3 nos. 40Amps DP RCCBs and Bus bars and other accessories

MAIN & SUB MAIN CABLES/WIRING Wiring for FRLS Wire circuit with 2x4.0+1x2.5sq.mm. insulated stranded copper conductor wires in recessed/surface MS conduit with earth wire complete as required (make: Havells / equivalent / Polycab / RRK / Finolex)

Wiring for circuit with 2x2.5+1x1.5sq.mm. 600V FRLS grade PVC insulated stranded copper conductor wires in recessed/surface 2mm thick PVC FRLS conduit with earth wire complete as required. (Make: Havells / equivalent)

Wiring for circuit with 2x1.5+1x1.5sq.mm. 600V FRLS grade PVC insulated stranded copper conductor wires in recessed/surface 2mm thick PVC FRLS conduit with earth wire complete as required. (make: Havells / equivalent)

POINT WIRING Modular switch / socket to be used. Wiring for light points with minimum 1.5 sqmm. 600 V , FRLS grade PVC insulated stranded copper conductor wires in recessed/surface 2mm thick PVC FRLS conduit complete with circuit wiring, earth wire, any other accessory required between luminaries and switch boxes etc. complete as required. The rate should include all required accessories and hardwares and other components required to complete the work at site.

One light controlled by 1 point

Two lights contld by 1 point

One switch socket plate of 5Amp

Socket Outlets & wiring for 6/16A power socket outlet points with 2.5/4 sqmm. 600 V , FRLS grade PVC insulated stranded copper conductor wires in recessed/surface 2mm thick PVC FRLS conduit complete with circuit wiring, earth wire, any other accessory required between socket outlets etc. complete as required. Note: Different color front plate required for UPS socket outlets (make: Havells / Polycab/ Finolex / equivalent / Legrand)

LIGHT FIXTURES AND EXHAUST FANS Supply and installation of LED indoor decorative recess type mirror optics fluorescent light fixture size (600x600mm) with all necessary accessories complete in all respect of approved make. Make: Philips- RC 140/RC380HE LED 30W

Supply and installation of Round LED (dia 150/200mm) recess type down light fixture in white colour finish complete with holder, lamp etc. Make: Philips Aura2 LED 15W

Supply and installation of Radiation Warning light (make- Philips/ Havells; Philips Deco Mini, Base B22 0.5Watt )

FIRE DETECTION AND ALARM SYSTEM Supply fixing and drawing of 2C x 1.5 sq mm FRLS grade PVC insulated stranded copper conductor wires drawn in 2mm thick 20 mm dia PVC FRLS conduit with all accessories and GI boxes in recess/surface including cutting wall and making good the same as required.

Supply, testing, installing and commissioning of the following fire detection and alarm accessories complete with connection etc. as required including the system's interlink connections with the Fire alarm panel at the reception :

Manual break glass unit. (make - Agni)

Smoke detector (Make- System Sensor/ Apollo)

Fire Alarm hooter. (make - Agni)

Response indicator (make - Agni)

Supply fixing and drawing of 2C x 1.5 sq mm FRLS grade PVC insulated stranded copper conductor wires drawn in 2mm thick 20 mm dia PVC FRLS conduit with all accessories and GI boxes on surface as required, for connecting with existing Fire Panel

EARTHING Supply, providing and testing of Chemical electrode earthing station complete with 3M Long, 38mm dia pipe. The rate shall include Excavation of earth, Construction of 450mmx450mm brick masonry chamber with heavy duty man hole cover etc. for Chemical earhig, Back Filling Compond for Chemical earthing etc. (Earth resistance ohms as per engineer in charge)

COPPER EARTHING CONDUCTOR : Supply, laying, & Termination of the Following sizes of earth wires laid in excavated/preformed trenches, cable trays, draw through pipe sleeves black color suitable size PVC sleeves along with Column/Wall for neutral and dedicated earthing as per specifications. Price should include proper earthing supports like Insulators, lamps with Vertical/horizontal cabletrays running above false ceiling and vertical shaft risers in electrical rooms.

Green Color PVC Insulated FRLS flexible copper cable with termination using thimbles/ lugs etc. complete in all respects in appropriate size MS conduit- 1C x 50 sq mm from Earth Box onwards.

Earth Bus Box - 300 mm long, 50mm wide x 6mm Copper Earth Bus in an Earth Box complete in all respects with Nut Bolts, insulators etc.

Misc. Items Room Signage for all rooms 12"x4" PVC acrylic Sheet

TELEPHONE & LAN WIRING Supply and drawing of 2 pair, 0.61mm dia unarmoured FRLS PVC insulated and PVC sheathed annealed tinned copper conductor telephone cables with 25mm dia PVC recessed/surface conduit and termination complete as required.

Supply and fixing in position RJ - 11 Telephone points i/c wall recessed GI box for LAN and face plate(computer network point)

Supply and laying of CAT 6E cable with 25mm dia PVC conduits and All computer network point should be terminated to TMH rack (Medical physics room no:AB-B-008,Annex building)

Supply and fixing of Network Switch with enclosure, power sockets 24 Port 1Gbps, in TMH computer network rack as per Project Engineers instructions Make - CISCO ,Model no-2960X-24TS-L managed switch

Supply and fixing in position RJ - 45 I/O face plates i/c wall recessed GI box for LAN of 'Systemax'make. Note:material used (passive component) for N/W point shall be Systemax make /brand

Supply and installation of portable fire extinguishers of class ABC type electrical fire with wall mounted and indicators in 5.0 Kg capacity

SETH INFRA