Community hall repair and development works in ward 8,24,33,36 package 2

Community Hall-02

Dewatering on BHP basis by using water pump including

diversion of stream, providing cofferdams, earthern bunds etc. as

may be necessary for foundation and other parts of the the works

and pumping out...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

High Density Polyethylene Membrane water proofing

Providing and laying water proofing treatment to the Rafts, Below grade

slab, Lift pits, water retaining structures with fully bonded High Density

Filling approved earth (excluding rock) in trenches, plinth, sides of foundations

and other similar works etc. in layers not exceeding 20cm in depth, consolidating

each deposited layer by ramming and ...

Construction of dry lean cement concrete Sub- base over a

prepared sub-grade with coarse and fine aggregate conforming

to IS: 383, the size of coarse aggregate not exceeding 25 mm,

aggregate cement ra...

Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar

1:4 (1cement: 4 coarse sand), with joints not exceeding 5 mm, including

filling the gaps with ordinary cement mixture & mixing w...

Providing 12 mm cement plaster with cement mortar 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, in...

Painting with synthetic enamel paint of approved brand and

manufacture of required colour to give an even shade :One coats on old

work as per specifications and as per directions of Engineer in charge...

Providing and constructing load bearing wall with Solid Concrete blocks

of size 400x200x200mm having block density more than 1800kg/m3

and minimum compressive strength of 4.00 N/mm2 conforming to IS

Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and

diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates

at the junctions and corners, 25 mm dia pulley, 40x40x6 mm...

Providing and fixing M.S. grills of required pattern in frames of windows

etc. with M.S. flats, square or round bars etc. including priming coat with

approved steel primer all complete. Fixed to steel...

Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 ...

Lettering with black Japan paint of approved brand and manufacture to give

an even shade including preparing the surface after thoroughly cleaning the

surface to remove all dirt, dust and foreign matt...

Painting Steel work with Deluxe Multi Surface Paint to give an even

shade. Two coat applied @ 0.90L/10 m² over an under coat of primer

applied @ 0.80 L/10 m² of approved brand and manufacture includ...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS...

Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) including cost of all materials, labour...

Providing and laying in Reinforced cement concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/basalt crushed graded coarse aggregates an...

Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 ...

Providing Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position, binding and anchoring to adjacen...

Providing 12 mm cement plaster with Cement mortar 1:3 (1cement: 3 coarse sand) finished with a floating coat of neat cement to brick masonry including rounding off corners wherever required smooth ren...

Providing and laying water proofing treatment to the Water tanks & Liquid Retaining structures with two component acrylic polymer modified cementitious waterproofing membrane with minimum elongation o...

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers including cost of material etc as per specifications and as per directions ...

Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Providing and laying in position Cement Concrete for levelling course for

all works in foundation. The granite/trap/basalt crushed graded coarse

aggregates and fine aggregates as per relevant IS Codes...

Providing Size Stone masonry with hard stone in foundation & plinth with

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position Cement Concrete for levelling course for

all works in foundation. The granite/trap/basalt crushed graded coarse

aggregates and fine aggregates as per relevant IS Codes...

Providing and constructing load bearing wall with Solid Concrete blocks

of size 400x200x200mm having block density more than 1800kg/m3

and minimum compressive strength of 4.00 N/mm2 conforming to IS

Providing 12 mm cement plaster with cement mortar 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, in...

Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 ...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement

including cost of all materials, machinery, labour, cleaning, straightening,

cutting, bending, hooking, laping/welding joints, tyin...

Providing& fixing of Openable door made out of multi chambered

UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium

Dioxide) at 6PHR with TPV(Thermo Plastic Vulcanized) and lead free

Providing & fixing upvc ventilator with Exhaust Turbo speed fan

with 5 blades (300mm x 300 mm & above sized fan) with copper motor

having mounting arrangements as per direction of Engineer in charge

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two coats on new work over an under coat of suitable shade with ordinary paint of appro...

Providing and fixing 1st quality ceramic glazed floor tiles conforming to

IS : 15622 (thickness to be specified by the manufacturer ) of approved

make in all colours, shades except burgundy, bottle gr...

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of approved make,

in all colours, shades except burgundy, bottle gre...

Providing and fixing white vitreous china pedestal type water closet

(European type) with seat and lid, 10 litre low level white vitreous china

flushing cistern & C.P. flush bend with fittings & C.I. ...

Polyurethane based Single Component for New Surface Providing and laying water proofing treatment to the Roof with PU based

single component elastomeric pure polyurethane based coating on New

Refilling available earth around trenches/pipelines, cables in layers not

exceeding 20 cms in depth, compacting each deposited layer by ramming after

watering with a lead upto 50 m, and lift upto 1.5 ...

Filling approved earth (excluding rock) in trenches, plinth, sides of foundations

and other similar works etc. in layers not exceeding 20cm in depth, consolidating

each deposited layer by ramming and ...

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar

taps, 32 mm C.P. brass waste of standard pattern, including painting of

fittings and brackets, cutting and making good the w...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all CPVC

plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre

long with S.S. triangular plate to Eureopean type W.C. of quality and make

as approved by Engineer - in - charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC

plain & brass threaded fittings This includes jointing of pi...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC

plain & brass threaded fittings This includes jointing of pi...

Providing and fixing PTMT stop cock of approved quality and colour 15 mm nominal bore, 86 mm long, weighing not less than 88 g

Providing and fixing PTMT stop cock of approved quality and colour 20 mm nominal bore, 86 mm long,

Providing and fixing Brass full way valve gate with C.I. wheel of

approved quality (screwed end) :25 mm nominal bore

Providing and fixing Brass full way valve gate with C.I. wheel of

approved quality (screwed end) :32 mm nominal bore

Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 g

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and ov...

Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Supply and delivery of Centrifugal pumpset at site brand new best make and with discharge duty confirming to ISI standards and its latest amendments

2 HP, Size 65x50 Head 13M, Discharge 462 LPM

Earth work excavation for pipeline trenches in all kinds of soils by mechanical means above 600 mm trench width as per drawing and technical specifications, including setting out, construction of shor...

Providing PVC ringtite pipes conforming to IS 4985:2000 with latest

amendments and conveying to worksite, rolling and lowering into

trenches, laying true to line and level and perfect linking at joi...

Constructing brick masonry chamber of internal dimension 600x600mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plaster...

Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m , and lift upto 1.5...

Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and running before concreting the ...

Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and running before concreting the ...

Supplying heavy gauge PVC Conduit Pipe ....dia .......mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hook sand ...

Supplying and fixing PVC/metal conduit Deep junction box

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Extra for Groove cutting in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering, finishing upto wall surface complete.

Supplying And Fixing Metal Fan Box with Round Hook.

Point wiring Copper without switch.Supplying and wiring adopting loop system in existing PVC Conduit /casing usingf 1100v Grade , COPPER conductor flexible multistrand FRLS PVC insulated., 2x1.5 Sqm. ...

Point wiring Copper without switch.Supplying and wiring adopting loop system in existing PVC Conduit /casing usingf 1100v Grade , COPPER conductor flexible multistrand FRLS PVC insulated., 2x1.5 Sqm. ...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified I...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified I...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified I...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified I...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293

Supplying of .....feet -PVC Batten with integrated LED tube .... W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI greater than 80. Power Input: 220-240V@ ...

Supplying of Ceiling Fan with Capacitor rating As per guideline of BEE 5 star rating and IS:374/79 and also comply with IS: 1709/1984 with latest amendment, Rated voltage 220 V/50 Hz, Rated power inpu...

Fixing all types and all capacities of fluorescent / false ceiling / spot light / CFL / LED fittings indoor on the wall / ceiling / rafters / girders using 23/0.0076” twin twisted PVC insulated ...

Fixing a ceiling /wall mounting fan of all capacities and all types, with necessary clA and 'S' hook made out of 15mm dia MS rod, with 5 A. ceiling rose of approved quality with necessary length of 23...

Supplying and fixing regular MCB distribution boards on wall / wood board / flush mounting using required clamps, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase ...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking ca...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking ca...

Supplying & fixing of Porcelain fuse channel with cut out onexisting wooden/panel using necessary nuts, bolts and washers.

GI Grounding pipe, B - Class, 42 mm dia, 2.5 Mtr long, 3.2 mm thick with bolt, nut, GI Strips and washer complete Minimum Weight of GI Pipe: 7.3 Kg

Good Quality well burnt Charcoal for grounding purposes packed in non returnable gunny bag of 30 Kg each

Good Quality Salt for grounding purposes packed in 50 Kg gunny bag

LT Single Phase 5-30 Amps, DLMS Complaint Static Energy Meter, 1.0 Accuracy Class (Used for LT-2, LT-3 & LT-5 Installations)

Providing and fixing Steel work welded in built up sections/ framed

work, including cutting, hoisting, fixing in position and applying a priming

coat of approved steel primer using structural steel et...

Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :Two coats on new work after

thoroughly brooming the surface to remove all dirt, dust, mortar drops

Ruled / Flush pointing on Sand stone masonry surface with lime, surkhi

and marble dust mortar in the ratio of 1 1.5 1/2 One lime 1.5 surkhi

50percent red and 50percent light yellow surkhi 1/2 marble...

Providing and fixing precoated galvanised iron profile sheets (size, shape

and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+

0.05 %) total coated thickness with zinc coating 120 g...

Providing and laying Cement concrete flooring 40 mm thick with 20 mm

nominal size stone aggregate using 1:2:4 (1 cement : 2 coarse sand :

4 graded stone aggregate) finished with a floating coat of nea...