COMPREHENSIVE MAINT INCLUDING DAY TO DAY ONLINE COMPLAINT MGMT SYSTEM/OFFLINE ORDERS WITH SCOPE OF REPAIR OF LEAKAGE/SEEPAGE IN ANY POINT OF THE EXTERNAL AND ALL MISC B/R AND E/M WORK ETC IN OTM ACCN AT RATNUCHAK MIL STN UNDER GE KALUCHAK

Note - Rate quoted below all items of this schedule inclusive provision as under making arrangement for establishment of centralized complaint centre in the existing building as under :- (a) Contractor shall be given user id and password for accessing the online complaint portal and contractor shall at his own expense by himself or his representative feed the data in r/o complaints so generated. (b) Manually registered complaints shall be obtained everyday from MES complaint cell and rectification or otherwise shall be intimated to JE in charge of the cell for updation of manual registers. (c ) Provision and maintenance of all tools, plants, equipment and safely gear required for tradesmen under this contract (d) Provision of communication and conveyance (as required) facilities to supervisor and tradesmen. (e) Monitoring and management of complaints report from generation to execution of complaint including pending complaints. (f) Updating status of lodged complaints on a daily basis. (g) Basic inputs to be noted from the complainants will be locality, Building No, Qtr No, Name and Rank of complaint and exact nature of complaint and mobile No/ telephone (j) On lodging the complaint, the Complaint No will be assigned for reference . Also system should indicate an approximate time for repairs. Accordingly a corresponding complaint slip shall be generated by the system with all relevant info. Complaint slip should be printed in triplicate and to be handed over immediately to Supervisor who shall detail appropriate tradesmen for repair with required materials/store. One copy of complaint shall be retained in complaint centre and two copies with tradesmen.

(Day to day online/offline complaint B/R & E/M)

S&F in repair Central Hole Basin Mixer chromium plated brass without Popup Waste System with 450mm Long Braided Hoses complete all as specified and as directed.

S&F in repair wall mixer non telephonic shower arrangement with connecting legs and wall flanges, cast copper alloy, chromium plated, complete all as specified and as directed.

S&F in repair chromium plated brass Wall Mixer 3-in-1 System with Provision for both Hand Shower & Overhead Shower Complete with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Flanges (without Hand & Overhead Shower) complete all as specified and as directed.

S&F in repair Sink Mixer swan neck with Swinging Spout (Wall Mounted Model) chromium plated brass with Connecting Legs & Wall Flanges complete all as specified and as directed.

S&F in repair CP brass Sink Cock with Swinging Spout (Wall Mounted Model) with Wall Flange complete all as specified and as directed.

S&F in repair 15 mm bore bib taps long nose/long body, cast copper alloy CP fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 gms ferrule and fixed complete all as specified and directed.

S&F in repair 15mm bore Bib taps CP fancy type, cast copper, screwed down, screwed for iron pipe or for brass ferrule and fixed.complete all as specified and as directed.

S&F in repair angle cock with wall flange, cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified and as directed.

S&F in repairs 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated,fancy type screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nuts complete all as specified and as directed.

S&F in repairs Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection and fixed in position fixed in repairs complete all as specified.

S&F in repairs CP alloy jet spray with flexible pipe n.less than 90 cm long fixed to EWC suitable for 15mm bore complete all as specified and directed.

S&F in repair fancy type Toilet paper holder, steel chromium plated approximate size 140X140X50mm complete all as specified and as directed.

S&F in repair chromium plated steel Tubular towel rail 20mm dia, D type, 60cm long between flanges. complete all as specified and as directed.

S&F in repair chromium plated steel towel ring 200 mm dia complete all as specified and as directed.

S&F in repair chromium plated towel rack 600mm long & 200mm wide with lower hangers,Stainless steel complete all as specified and as directed.

S&F in repair soap dish steel chromium plated 100 mm size complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F in repair Corner Glass Shelf 5.5 mm thick (300x300mm) chromium plated guard and railing(with Bracket) as per directed by Engr-in-charge.

S&F in repair wash hand basin waste coupling of chromium plated brass 32 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basin complete all as specified and as directed.

S&F in repair sink waste coupling of chromium plated brass 40 mm dia with long screwed shank and fly nuts complete all as specified and as directed.

S&F in repair for 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed.

S&F in repair PVC connection 15 mm x 600 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified and as directed.

S&F in repairs CP Fancy type shower rose 200mm x 200mm square with long CP arm of approved quality complete all as specified.

S&F in repairs wash hand basins, vitreous china,of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand inclusive of fixing of 32 mm dia waste fitting and waste pipe etc complete all as specified.

S&F in repair vitreous china white under counter wash basins(595x420x200 mm ) oval shape, incl waste pipe, brackets, and connecting pipe fixed complete all as specified.

S&F in repair full pedestal for WHB complete all as specified and as directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged surfaces, complete all as specified and as directed by Engineer-in-charge.

S&F in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom,complete all as specified and as directed.

S & F in repair Vitreous china Water closet pedestal pattern cascade type with in built flushing cistern and seat cover with complete fitting complete all as specified complete all as specified and as directed.

S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including PVC P-trap, & PCC bedding in 1:2:4 and making good disturbed floor with existing specifications connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition) complete all as specified and as directed.

S&F in repair sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495X420 mm bowl size 410x330x160mmmm complete with CP waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge.

S&F in repairs sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified.

S & F in repair Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (39"x30"x10") fixed with steel fastners or steel screw complete all as specified and as directed.

S&F in repair, brass face/Spindle as per sample for CP/Brass Bib tap, Angle/Stop cock, Pillar cock, wall mixer, WHB mixer, concealed stop cock etc for 15 mm bore pipe complete all as specified and as directed by Engineer-in-charge.

As per item No 38 but spindle for long body concealed stop cock complete all as specified and as directed.

S&F in repair stainless steel lock grating plain/hole size 100 mm dia including embeding in tiles with white cement complete all as specified and as directed.

S&F in repair PVC Waste pipe 32mm bore of required length complete all as specified and as directed.

S&F in repair PVC Waste pipe 32/40mm dia for urinal with fixing arrangments of required length complete all as specified and as directed.

S&F in repair 1000 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including 20 mm dia float valve (PVC) and 02 no's GI tank nipple(20mm dia fo & 75mm long) complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including 20 mm dia float valve (PVC) and 02 no's tank nipple (20mm dia fo & 75mm long) complete all as specified and as directed by Engineer-in-Charge.

M & L for cleaning of water storage tank 500 litres capacity completely by removing all scale dirt / dust of any description with chlorine complete all as directed at site including taking down and refixing of tank at the same place, any damage will be rectified by the contractor at his own risk and cost all as directed.

M & L for cleaning of water storage tank 1000 litres capacity completely by removing all scale dirt / dust of any description with chlorine complete all as directed at site including taking down and refixing of tank at the same place, any damage will be rectified by the contractor at his own risk and cost all as directed.

S&F in repair Ball valves/float valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 15 mm bore pipe including making connections complete all as as specified and fixed (Minimum weight 20mm-210 gms).

_Ditto- 20 mm dia all complete all as specified and as directed.

_Ditto- 25 mm dia complete all as specified and as directed.

S&F in repair MS peg set of six power coated as approved by GE complete all as specified and directed.

S&F in repairs PVC over head tank cover / lid of size suitable for capacity of above 500 litres and upto 1000 litres capacity complete all as specified and directed.

Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

_Ditto- but 20 mm dia complete all as specified and as directed.

S&F for fittings in repair for steel tubing galvanised, 15 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts,including taking down and refixing of pipe between joint of fittings etc. complete all as specified and as directed

S&F for fittings in repiar for steel tubing galvanised, 20 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts, including taking down and refixing of pipe between joint of fittings etc. complete all as specified and as directed

S&F in repair 20 mm nominal outer dia Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all necessary fittings like Plain and Brass CPVC SDR 11 fittings on walls/ceiling or laying in floors,including fixing the pipe with clamps. This includes jointing of pipes & fittings with one step CPVC solvent cement, complete as per direction of Engineer in Charge.

S&F in repair CPVC brass elbow 20 mm outer dia all complete all as specified and as directed.

S&F in repair CPVC brass elbow 20 mm outer dia (3/4x1/2) all complete all as specified and as directed.

S&F in repair CPVC brass Tee 20 mm outer dia all complete all as specified and as directed.

S&F in repair CPVC male brass threaded adapter 20 mm dia((MTA/MBTA) complete all as specified and as directed.

S&F in repair CPVC female brass threaded adapter 20 mm dia. ((FTA/FBTA) complete all as specified and as directed.

S&F in repair CPVC socket 20 mm dia complete all as specified and as directed.

S&F in repair PVC syphon kit for one pice water closet with cistern of any capacity inclg float valve washer, push button etc complete all as spd and directed.

S & F in repair plastic water closet seat cover, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repairs 20 mm dia Gun metal, globe or gate valve with iron wheel head,screwed both ends for iron pipe complete all as specifed and dicrected.

S&F in repairs 15 mm dia Gun metal, globe or gate valve with iron wheel head,screwed both ends for iron pipe complete all as specifed and dicrected.

S&F in repair extruted Aluminium alloy handles fabricated type anodised 150 mm long complete all as specified and directed.

S&F in repair extruted Aluminium alloy handles fabricated type anodised 125 mm long complete all as specified and directed.

S&F in repair 150 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

S&F in repair 200 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

S&F in repair 300 mm long dia aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

S &F in repairs mild steel Helical door spring of size 300 mm at site including welding to steel chowkhats, complete all as specified and directed.

S&F in repair 40 mm dia cupboard knobs fixed with nut and washer brass polished bright finished complete all as specified and directed.

S&F in repair modular auto concealed soft closed hinges 35mm, 110 degree size fixed to cupboard complete all as specified and as directed.

S&F in repair magnet catcher 50 mm size for kitchen cupboard shutter complete all as specified and directed.

S&F in repair 100 mm hasp and staple safety type aluminuium anodised including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F in repair curtain rod of stainless steel 20mm dia and side capes fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified as directed by Engineer-in-Charge

S&F in repair drapery curtain rod of metalic 20mm dia covered with PVC coating including MS bracket, end ball, rounded block (coated with brown/cherry/golden colour) of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

S & F 5.0 mm thick sheet glass figured /frosted quality and glazing with oil putty in squares n. exc 0.8 sqm in each pane and fixed to ventilator complete all as specified and directed.

S&F 5.5mm thick sheet glass, orinary quality glazing with oil putty in suare n.exc 0.8 sqm in each pane complete all as specified and directed.

S&F in repair aluminium extruded section body, door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F in repairs, double action floor spring hydraulically regulated, made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, govrning pivot made of brass, other parts made of mild steel heavy duty and including taking down aluminium door shutter and refixing complete all as specified and directed.

S&F in repair 18mm thick single layered HDHMR coloured / textured finish board density more than 850 Kg / cum smooth finished fixed in cupboard and jointed together with necessary adhesive complete all as per directions by Engineer-in-Charge, manufacturer’s specification complete all as specified and as directed

Hacking out old broken glass panes(any thickness, size,quality or description) from steel frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3mm thick sheet glass, orinary quality glazing with oil putty in suare n.exc 0.5 sqm in each pane complete all as specified and directed.

All as per item No.86 above but figured glass, Pin head type complete all as specified and as directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

S&F in repair 30mm wide flap (when open) SS Continuous (piano) hinges, bright finish or electro galvanised fixed to Kitchen cuboard complete all as specified and directed.

S&F in repair medium weight, cold rolled with galvanized mild steel hinge pin, anodized, 75mm size.complete all as specified and as directed.

S&F in repair medium weight, cold rolled with galvanized mild steel hinge pin, anodized, 100mm size complete all as specified and as directed.

S&F in repair medium weight, cold rolled with galvanized mild steel hinge pin, anodized, 50mm size complete all as specified and as directed.

S&F in repair Mild steel Mortice lock verticle type, size 100mm long with 4 levers complete all as specified and as directed.

S&F in repair Mild steel Mortice lock verticle type, size 75mm long with 4 levers complete all as specified and as directed.

Supply & fixing in repairs switch piano, flush type single pole one way 5Amp, 240 volts ISI marked complete all as specified and directed .

Supply & fixing in repairs Socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed .

Supply & fixing in repairs Switch socket outlet combined 5 pin 5 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fixing in repairs Switch socket outlet combined 2 in 1 , 3 pin 5 amp and 15 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fixing in repairs Socket outlet 5 pin, 15 Amp, flush type, 240 Volts, 6 pin flush type complete ISI marked complete all as specified and directed.

Supply & fixing in repairs switch piano, flush type single pole one way 15 Amps, 240 volts ISI marked complete all as specified and directed .

S&F in repairs Modular switch 1 way 6A,1 module , 240 volts ISI marked complete all as specified and directed

S&F in repairs Modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and directed

S&F in repairs Modular Socket, 6A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

S&F in repairs Modular Socket 6A/16A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

S&F in repairs Modular Fan step regulator, 120W 1 module , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 3 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 4 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 6 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 8 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs modular white cover plate with frame 12 module complete all as specified , 240 volts ISI marked complete all as specified and directed

S&F in repairs distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as directed by Engr-in-Charge. Note:- Distribution board and MCBs should be same make.

S&F in repairs 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed.

S&F in repairs 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning.complete all as specified and as directed.

S&F in repairs SPN 32 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

S&F in repairs SPN 40 to 63 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply & fix in repairs calling bell ding dong/buzzer ,AC 230Volts single pole complete all as specified and directed.

Supply & fix in repairs stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed.

S & F in repairs for bell push , flush type single pole , 5Amp, 240 volts all as specified .

S&F in repairs Ceiling Rose 3 terminal surface type Complete all as directed.

M& L in repairs for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

M& L in repairs Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K Complete all as directed.

S&F in repairs LED lights fitting 1x 20W, 220V, AC batten type complete with LED tube rod 20 watts driver, holder and power factor > 0.9 , 100 Lumen/Watt,SPD 2.5KV ,6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz.complete all as specified and as directed.

S&F in repairs LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F in repairs bulk head luminaries IP65 with opal diffuser 10 watt, 230 Volts LED type complete with 10 watt LED Bulb all as directed Engr-in-Charge.

S&F in repairs plug top 15 Amps complete all as specified and directed.

(Periodical Services)

M&L for preparation of old plastered surfaces and applying one coat of white wash on Ceiling complete all as specified and as directed.

M&L for preparation of old plastered surfaces and applying two coat of white wash on Ceiling. Complete all as specified and as directed.

M&L for Preparation of old decorated surfaces (Plastered or unplastered) of walls incl cornices, pillars etc by brooming down or smoke root, moulds mass includidng applying one coat of weather coat of any color, complete all as specified and as directed.

M&L for preparation of old surface of wood rubbing down by sand paper and applying one coat of synthetic enamel paint over wood surface over 10 cm width or girth complete all as specified and as directed.

M&L for preparation of old surfaces of steel over 10cm width or girth incl, rubbing down by sand paper or scrapping the old coat by blowing lamp and applying one coat of synthetic enamel paint over steel surface over 10cm width or girth complete all as specified and as directed.

M & L for preparation of old plastered surfaces of wall and applying two coats of oil bound distemper complete all as specified and as directed.

M & L for preparation of old plastered surfaces of wall and applying one coat of oil bound distemper complete all as specified and as directed.

M & L for complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/Chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ceiling by filling cracks by Berger Bison Putty / crack fill paste of Berger Paints or equivalent make and make good smoothen surface by sand paper and applying two coats of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1.5 mm thick exterior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed.Allow 6-8 hrs to dry the surface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Ultima.

M & L for 15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished even and fair without using extra cement including mixing of water proofing compound complete all as specified and as directed. Note: - Water proofing compound shall be measured and paid separately.

M & L for preparation of newly plastered surface and applying two coat of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1mm thick exterior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airlessspray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex

Srl Item No 134 & 136 Contd/.... Note :- (a) Work shall be done as per 'Memorandum of Understanding' (MOU) between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed. (b) The contractor shall upload 'Memorandum of Understanding' (MOU) between tenderer and manufacturer of paints and their authorized applicator after conclude of tender and before place of Work Order Documents as mentioned in NIT. (c) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE.

(JOINERY)

Taking down shutters of any description exc 1.00 Sqm and n.exc. 2.00 sqm each and removing from the site complete all as specified and directed.

BLANK

Taking down Chowkats or frames exc 1.5 sq.m but n.exc 4 sqm each each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F stainless steel basket (plain) of size 370mm x 485mm x 150 mm made of min 4 mm dia stainless steel wire approved quality with suitable arrangement for fixing telescopic basket over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in -charge.

S & F stainless steel basket (plain) of size 370mm x 485mm x 200 mm made of min 4 mm dia stainless steel wire approved quality with suitable arrangement for fixing telescopic basket over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in -charge.

S & F stainless steel basket (plain) of size 370mm x 485mm x 100 mm made of min 4 mm dia stainless steel wire and bottom of S S perforted sheet approved quality with suitable arrangement for fixing telescopic basket over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in -charge.

S&F Pressed steel frames (factory made) made out of 1.25 mm thick black MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 105x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3mm thick flat iron projecting 10 cm on either side complete all as specified and directed.

All as per Item No. 145 here in before but size of frame 125X60mm for fixing of two shutters complete all as specified and directed.

M&L cement concrete (1:3:6) type C0 using 12.5mm graded stone aggregate filling in pressed steel chowkats bed block for holdfast and the like complete all as specified and directed.

S&F Factory made solid PVC moulded Door frame of size 50x100mm with wood free EPS and 2mm thick moulded PVC sheet alaround supplying and fixing in wall at site as per manufacturer specification complete all as specified and as directed.

S&F Factory made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned complete all as specified and directed.

S&F 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and directed.

S&F Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

M&L pressed steel frames for cup board chokhat of size 60x40mm with one or more rebates incl necessary fixing lug, hold fasts etc complete all as specified and directed.

S&F 100 mm size stainless steel hinges medium weight cold rolled complete all as specified and directed.

S&F 100 mm hasp and staple safety type aluminuium anodised including bolt to hinge plate and fixed with screw complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid for separately). →Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing all as specfied and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside

S&F 30mm wide flap (when open) SS Continuous (piano) hinges, bright finish or electro galvanised fixed to Kitchen cuboard complete all as specified and directed.

S&F18mm thick single layered HDHMR coloured / textured finish board density more than 850 Kg / cum smooth finished fixed in cupboard and jointed together with necessary adhesive complete all as per directions by Engineer-in-Charge, manufacturer’s specification complete all as specified and as directed

S & F 18 mm thick factory made 100 % solid WPC flush shutter (for cupboard and vanity etc)made from co-extruded three layer rigid foam sheet(single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and directed.

S&F modular auto concealed soft closed hinges 35mm, 110 degree size fixed to cupboard complete all as specified and as directed.

S&F magnet catcher 50 mm size for kitchen cupboard shutter complete all as specified and directed.

M&L for preparing surface of new wood and wood based material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparing surface of new steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint complete all as specified and directed.

Dismantling wrought iron or mild steel work as in cooler stand, chazza etc complete all as specified and as directed.

S&F Mild steel framed works such as grills, framed guard bars, etc and similar work as in cooler stands, chazza stand etc. conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S&F in repair aluminium powder coated aluminium door shutters with frame with the following specification. (i) Door frame size 115x60x3mm, (ii) Door Shutter sections top rail 100x40x2mm (iii) Door Shutter Middle rail 150x40x2mm. (iv) bottum rail 200x40x2mm. (v) Vertical styles 100x40x2mm. panelling of shutter is to be carried out with not less than 5.5mm thick. frosted glass including necessary joining cleats, glazing clips, rubber neoparene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading, screws, two way floor door spring, mortise lock with keys etc.complete all as specified.

S&F in repair powder coated aluminium window and ventilator shutters, fixed type not less than 5.5mm thick. frosted glass without sash bar, aluminium section weighing 0.55 kg/m including grill and necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F in repair powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S&F in repair powder coated aluminium three track sliding type glazed window, with frame of size 150x60x2mm thick and with sliding three track shutters of size 100x38x1.4mm thick. Two nos shutter are to be fitted with 5.0 mm thick plain sheet glass and one shutter with stainless steel wirecloth of 0.56 mm dia and 1.18 mm aperture. The window is also to be fitted with aluminium powder coated grill casted out of 5.50mm thick diamond shape section and with aperture not less than 75mm shall be fixed to frame. Incl all necessary fiber wheel rollers suitable handle to facilitate sliding and all necessary jointing cleats glazing clips,rubber packing, Aluminium snap beeding etc complete all as specified and directed .

S & F Factory made single extruded WPC (Wood Polymer composite) solid door/window/ceosetory windows and other frames / chawkhat of size 65 x 100mm comprising of virgin PVC polymer of K value 58-60 (Suspension grade) Calcium carbonate and natural fibers (wood powder / rice husk / wheat husk) and non toxic additives (Max toxicity index 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws havinf min frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) & 1100N (Edge), min compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof water / moisture proof and fire retardant and fixed in position with MS hold fasts / lugs/ stainless steel dash fasternersof required dia and length complete all as specified and directed. (MS hold fasts / lugs / SS dash fasterners shall be paid seprately.) complete all as specified and as directed.

S & F Factory made single extruded WPC (Wood Polymer composite) solid door/window/ceosetory windows and other frames / chawkhat of size 65 x 125mm comprising of virgin PVC polymer of K value 58-60 (Suspension grade) Calcium carbonate and natural fibers (wood powder / rice husk / wheat husk) and non toxic additives (Max toxicity index 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws havinf min frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) & 1100N (Edge), min compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof water / moisture proof and fire retardant and fixed in position with MS hold fasts / lugs/ stainless steel dash fasternersof required dia and length complete all as specified and directed. (MS hold fasts / lugs / SS dash fasterners shall be paid seprately.) complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F Extruded Aluminium alloy handles fabricated type anodised 150 mm long complete all as specified and directed.

All as per item No 177 here-in-before but 125 mm long complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

All as per item No 179 here-in-before but 200mm long complete all as specified and directed.

S&F 300 mm long dia aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

S &F mild steel Helical door spring of size 300 mm at site including welding to steel chowkhats, complete all as specified and directed.

S&F 40 mm dia cupboard knobs fixed with nut and washer brass polished bright finished complete all as specified and directed.

S&F 300 mm long stainless steel 304 grade sliding door bolt with hasp staple(bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding door bolt of extruded section complete all as specified and as directed.

S&F stainless steel 304 grade tower bolts 200 mm size, and fixed all as specified

S&F 150 mm stainless steel 304 grade 19mm dia handle cast type (round shaped) complete all as specified.

S&F floor door stopper of stainless steel 304 grade alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

M&L for Spot/running welding to loose gate/ window hinges, tower bolt, handle, stay etc. after taking down & refixing in same position and making good welded area as per exsiting. Complete all as spd and directed.

(Leakage/Seepage and certain other works)

Taking down cement plaster of any description on brick stone or concrete walls/ceiling surfaces including raking out joints hacking for keys scrubing down with water etc complete all as specified and directed

M&L for 15 mm thick rendering in CM 1:6 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L 5mm thick rendering on ceiling surfaces in CM 1:3 to be finished even and smooth with extra cement complete all as specified and as directed.

Supply only integral water proofing admixture of approved quality complete all as specified and as directed.

M&L for Preparation of new plastered surfaces as in ceilings and applying two coats of white wash complete all as specified and as directed.

M&L for new plaster surface two coat of oil bound distemper over 1.5mm thick of birla white putty including preparation of newly plastered surface etc all as specified.

Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing with moderate acid solution, the top layer with brushes and water to expose the stone chippings complete all as specified and directed.

Providing and applying water proofing treatment using acrylic polymer emulsion modified cement based water proofing coating with fibre glass mesh and raintile shall be mixed to cement at the rate of 1:2 and the following steps are as under to be followed during the treatment. a) Clean the surface with wire brush and remove all loose and friable particles from the wall which could affect the bond between the surface and the waterproofing coating. b) The surface is to be repaired with 10 mm thick plaster in CM 1:3 with using water proofing liquid @ 200 ml per bag of cement. c) when the surface is repaired first coat of Sika/Pidilite/Dr Fixit raintite, a flexible protective waterproofing coating is applied with a hard plastic bristled brush and left to harden for 2 to 6 Hours. d) After the first coat dries,fiber glass mesh with second coating raintite. e) Top coat 107 top seal by finish. f) Using curing of screed and plaster are recommended. g) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (j) Taking down existing water proofing treatment and cleaning roof surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500 m where directed.

Dismantling unframed work timber scantling 40 Sqcm and over in section in any position as in unframed work complete all as specified and as directed.

Dismantling timber scantling in fillets, posts, rafters, purlins etc under 40 sq cm in section complete all as specified and as directed.

S&F Rolled sections conforming toFe-410W (GradeE-250) quality 'A' as in main and cross beams, hip and jack rafters; purlins, trusses, stagging, where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Beam, tee, angle, channel or flat sections or MS tube pipe) complete all as specified and as directed.

Dismantling AC corrugated, semi corrugated sheets in roof covering including ridge complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in roof covering fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in ridge of roof fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

M & L for preparing surface of new steel of any description over 10cm width and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Demolition of concrete in ground floor not exceeding 15cm in thickness below or above ground level including floor finish such as tiles of any thickness and any description etc. complete all as specified and as directed by Engineer in Charge.

Demoilition of lean/cinder concrete filled in sunken slab , wire brusing the surface ,cleaning all loose dirt by dusting/watering sunken portion of WC, Toilet etc and applying cement slurry @1.5 kg per Sqm incld dismentaling of tile complte all as specfied and directed

Dismanting floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed.

M&L for vitrified tiles any colour 10 mm thick (square/rectangular) polished as in floor , area of each tile n. exc 0.36 sqm etc set and jointed and laid with 5mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions, 15mm thick screed bed in CM 1:6 & pattern, laying etc of tiles and Shade, Colour shall be decided by Engr in Charge complete all as specified.

All as per item No 209 but in vertical surfaces with 5mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions including 15mm thick backing coat in CM 1:4 complete all as specified

M & L for Non - skid joint free coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. laid with 5mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions incldg 15mm thick screed bed in CM 1:6 complete all as specified and as directed. complete all as specified and as directed by Engr-in-Charge.

All as per item no 211 above but in vertical surfaces including laid with 5mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions including 15mm thick backing coat in CM 1:4 complete all as specified

M & L for Non - skid joint free coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. laid with 5mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions incldg 15mm thick screed bed in CM 1:6 complete all as specified and as directed by Engr-in-Charge.

M&L for coloured glazed ceramic tiles glossy finish of size 450x300x 7mm thick in dado’s/skirting etc (1st quality). laid with 5mm spacers set and jointed in laid with 5mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions to match, pattern, laying etc of tiles incldg 10mm thick CM 1:4 plaster and Shade, Colour shall be decided by Engr in Charge complete all as specified.

M & L for (Ist quality) coloured digital glossy wall tiles of size 300 x 600 x 7 mm thick as on vertical surfaces such as skirting/dado etc including 15mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for exterior grade full body vitrified tiles matt finished 400 x 400 x 12mm thick set jointed in neat cement slurry and pointed with grey cement and pigments to match the shade of tile pattern as approved in floors incl 15mm thick screed in CM 1:6 complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick as in floor to match the shade of the slab including 20 mm screed bed CM 1:6 including rubbing polishing complete all as specified and directed.

M&L machine cut kota stone slab flooring 18-20 mm thick as in riser in step, skirting/ dado to match the shade of the slab incl rubbing and polishing over and including 10 mm rendering in CM 1:4 complete all as specified and directed.

M&L for 18mm to 20mm granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and incl Screed bed or bedding layer of mortar 20mm thick in CM 1:6 and taking down old complete all as specified and directed.

Providing edge moulding to 18-20mm thick Granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B 0(12.5mm graded crushed stone aggregate) , as in sub base / floor complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight) complete.

M & L for providing 75 mm thick plain cement concrete 1:4:8 mix, type D-2 (Using 40mm graded stone aggregate) as sub-base floor complete

Dismantling Stone slabs laid dry and tiles of any description or thickness in floors/skirting, aprons etc. and rubbish off the premises complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete

Providing, cement concrete Type B1, 1:2:4 (20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges

M & L for providing water proofing treatment to sunken floors all as given below :- (a) Making fillet of size 25mm x 25mm at corner of slab and wall with polymer modified cementitious (PMC) mortar consisting of one part of tapecrete P-151, two parts of cement and 6 parts of fine sand by weight. (b) Sealing of joints of pipe with epoxy putty or epoxy mortar (c) Cleaning the concrete surface by brushing & watering and applying a coat of tapecrete P-151 Acrylic Polymer Modified cementitious slurry consisting of one part of Acrylic based polymer modified cementitious flexible compostie coating and two parts of cement by weight. The coating shall be carried out upto 300mm above FFL and shall be allowed to dry for 4-6 hours. (d) Appying a coat of Acrylic based polymer modified cementitious flexible compostie coating brush topping 1.5mm thick consisting of one part of Acrylic based polymer modified cementitious flexible compostie coating, two parts of cement and two parts of silica sand by weight and cured to 2 days. (e) Applying 15mm thick plaster in CM 1:4 mixed with WPC @ 100ml per 50 Kg cement on treated surface. (f) PCC 1:5:10 type E2 in sunken area.

M & L for provision of roof treatment with polymeric water proofing membrane all as given below :- (a) Taking down existing water proofing treatment and cleaning roof surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500 m where directed. (b) M & L for plastering 10mm thick in CM 1:3 using 100% coarse sand on roof surface including water proofing compound as per manufacturer's instructions and as directed by Engr-in-Charge. (c) Applying a coat of bituminous primer conforming to IS : 3384-1986 @ 0.25 Iitres/sqm on prepared surface and allowed to dry. (d) Applying and laying 3mm thick APP membrane having non oven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (e) M & L for two coats of aluminium paint on membrane surface all as specified and directed.

M & L for Complete removal of existing roof treatment or roof tile or plaster and removing from site to a place outside defence land as specified by civil authorities and clean the surface of roof with water and remove dust complete all as specified. M&L for highly elastic, UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates,with ability to bridge cracks ,cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years Warranty .ASTM D 6083-97a Waterproofing and heat reflecting system having following key performance properties: 1.UV resistant ,prevent yellowing and weathering 2.Highly elastic upto 350% and crack bridging 3.Excellent adhesion on porous and non-porous substrates 4. Tensile Strength >10 N/mm2 with GeoTextile fleece 5. Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11 System: SRI tile 300mm x 300mm x 10 mm thick set, jointed and pointed in roof floor/terraces over and including 15mm thick screed bed in CM 1:4 with chemical based adhesive as per manufacturer instruction complete all as specified and directed First coat:Providing and applying OEM prescribed compatible primer over the prepared surface for adhesion and bridging cracks. Coverage: 0.2kg/m2(with 50% dilution of water Reinforcement: Geotextile 40 gsm Second coat: highly elastic, UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates,with ability to bridge cracks. Consumption: 0.5 kg/m2. Third coat: highly elastic, UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates,with ability to bridge cracks. Consumption : 0.8 kg/m2 System buildup-1.5kg/sqm with geotextile of 40gsm. For accessible roof, tiles with screed/ adhesive may be fixed there after.

Taking down eaves gutters and rainwater pipes (any size or pattern) , including all fittings, heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories).complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints,complete fixed to walls at any height complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints complete laid in trenches or in floors complete all as specified and directed.

S&F 110 mm borePVC (SWR) pipes single socketed in any length with rubber ring joints complete fixed to walls at any height complete all as specified and directed.

S&F 110 mm borePVC (SWR) pipes single socketed in any length with rubber ring joints , bends ,Tees complete laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends 110 mm radius complete all as specified and directed.

S&F PVC (SWR) bends 75 mm radius complete all as specified and directed.

S&F 110 mm PVC(SWR) Junction single(T) equal /Unequal complete all as specified and directed.

S&F 75 mm PVC(SWR) Junction single(T) equal /Unequal complete all as specified and directed.

S&F PVC (SWR) bends any radius provided with access door of 110mm dia complete all as specified and directed.

All as per item No 239 above Above but 75 mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl of radius of 75 mm dia complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concerete B1 (1:2:4) complete all as specified and directed.

S& F in repair Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 75/100 mm bore pipe complete all as specified and directed.

Taking down ceiling plaster & cleaning the steel & concrete surface apply anti-corrsion coating to steel surface with Dr Fixit Rubber guard two coats, then apply bonding agent of pidilite (Dr fixit Pedilite URP) & than apply ready repair mortar thickness as required(not more than 50mm in two coat or three coat as per site requirement) with FOSROC HB-40 and finishing the surface even and smooth complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,drains etc, but excluding ashlars facings, dressed stone work and precast concrete articles.complete all as specified and as directed.

M&L Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified & as directed.

All as per item No.246 above but except bricks complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall in CM 1:4 complete all as specified & as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for reinforced cement concrete, type B1, 1:2:4 mix (20mm graded aggregate) as in slabs & Shelves etc complete all as specified and directed.

Formwork to soffits of slabs including supports, overhangings etc, for fair finished surfaces of concrete complete all as specified and directed.

Form work to edges of roof slab of thickness not exc 20cm wide and as in similar work complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

Dismantling boarding, any description, fixed in any position with nails/screws complete all as specified and directed.

Providing & Fixing in position suspended false celling system using E Grid suspended celling Grid system of M/S Everest industries Ltd or India Gypsum. The size of Grid shall be 600X600mm with GI frame work, main runner 39X24mm, cross tee 29X24mm and wall angle 22.2X22.2mm using 4mm thick High Pressure Stream cured non primered classic/designer variant E-Board ISI Marked IS No 14862-2000. Fibre cement E Board to be placed in the gird of E Grid suspended ceiling grid system duly suspended by 4mm dia GI bar hangers from the pulins of the roof with butter fly clips incl Dismentling wall and ceiling boards (fibre pulp/insulation ) any thickness including cover fillets including taking down All electric fittings fixed with ceiling and refixig the same in position after repalcing the ceiling).complete all as specified and directed.

M&L for Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.complete all as specified and directed.

M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Removal of plant growth from wall/roof projection or along the soil /rain water down pipe at any level by injection with chemical Glyphospate solution (410 concentration) of 20mm or till refuse by cutting or injection in stem of plants or roots at 30mm including scaffolding for any height upto triple storey complete all as specified and directed and as per Manufacturer instruction complete all as specified and directed.

(Summer/Winter appliances)

Labour for repair/servicing of ceiling fan of any capacity complete with strip opening of ceilling fan for repair/cleaning/varnishing and removing of old lubricating substances from bearing/ bush by using Kerosine oil, carrying out fresh lubrication , greasing and to make the ceiling Fan noise free and smooth functioning, including replacement of worn out/unserviceable minor spare parts split pin,fan body bolts,spring washer,fan rod bolt etc and PVC insulated, unsheathed stranded twin twisted copper conductor cable of size 1.5 Sqmm up to 1.0 M long, assembling the repaired ceiling fan and testing to the entire satisfication of engineer in charge and refifixing in its orginal position all as specified and directed. (Replacement of Spares flexible wire etc/rewinding of ceiling fan/shall be measured and paid seperately under respective item for M & L cost .) complete all as specified and as directed.

All as per Srl item No. 262 above but for exhaust Fan of any type and any sweep complete all as specified and directed.

Rewinding of ceiling fan, of any make/type and size (1200 sweep) with super enamelled copper wire of appropriate gauge as existing to obtain the specified and satisfactory RPM as per manufactures specification, including replacement of all insulation materials, varnishing, heating, drying, assembling of stater/rotor, connection & testing complete all as specified and directed.

All as per Srl item No. 264 above but for exhaust fan of any make/type but of size 300 mm sweep complete all as specified and directed.

Labour for remetalling of worn out shaft of fan, cutting,bracing,machining and polishing to make the shaft suitable for fixing of new ball bearing and fixing ball bearing in repair of bushing system in ceiling fan and assembling the same and testing to the engineer satifaction of engineer in charge to ensure smooth and noise free operation (bearing shall be measured and paid seperately )complete all as specified and as directed.

S&F in replacement ball bearing of any size and type, suitable for ceiling Fan complete all as specified and directed.

All asper item No. 267 above but for exhaust fan of any type/make and size complete all as specified and directed.

Supply & fixing in repair of capacitor 230 Volt AC 50 Hz, conforming to IS-1709 and Rated capacity 2.5 MFD for ceilling fan & exhaust fan complete all as specified and directed.

All as per item No. 269 above but of rated capacity 4.0 MFD for Exhaust Fan complete all as specified and directed.

Supply and connection of PVC insulated, unsheathed multi stranded,three core twisted copper flexible cable of size 1.5 Sqmm as required complete all as specified and directed.

Supply and fixing in replacement bush of suitable size for ceiling fan/exhaust fan of any type/size as per existing type complete all as specified and directed.

S&F in replacement of PVC connector 4 way 6 Amps with connection screws, nuts complete all as specified and directed.

S&F in replacement of PVC clamps with fixing screws for holding capacitor of any type and size complete all as specified and directed.

S&F in replacement of GI/ MS anodized bolts with anodized nuts, spring washers, split pin etc size 50 mm long 10 mm dia half threaded type with split pin hole complete all as specified and directed.

S&F in repair MS clamp for down rod of suitable size including gromet / reel type rubber pad with bolts, nuts,split pin and washers suitable for housing ceiling fan.

S&F in repair of ceilling fan down rod 12 mm dia and 30/45 cm long complete with MS Clamp Rubber reel,split pin nut bolts etc complete all as specified and directed.

S&F in replacement Printed circuit board (PCBs) suitable for BLDC ceiling fans of 1200 mm.complete all as specified and directed. Make - As per sample .

S&F in repair of louver shutter made out of MS sheet metal 1.2 mm thick for round base and 0.8 mm thick for flaps, comprising of mounting legs frames made o MS flat strips of size 25mm x 3mm includidng heavy duty rust proof passivated bolts of size 50 mm long 8 mm dia to be fixed on wall at ground/First/Second floor etc complete with using fastener bolt,driling for exhust fan up to 400 mm sweep incl taking down old one.

Cleaning of ceiling fan assembly of any type/size and carrying out two coat of spray painting with first quality synthetic enamelled paint of approved colour all as directed and specified.

S&F in repair PVC Canopy set of two pieces for ceiling fans of any size complete all as specified and directed.

S&F in repair Ceiling Fan blade set of three pieces suitable for 1200/1400 mm sweep of White/Brown/Ivory colors all as specified and directed. Make - As per Sample

Taking down and strip opening to geyser of any make and capacity 25 / 35 / 50 ltrs including disconnection of all water pipe connection and taking out water inlet / outlet assembly, removing glass wool, the inner tank, descaling the assembly and tank, detecting the leakage, welding / brazing the defective parts, repacking the glass wool and refixing the same after making it functional including replacement of worn out nuts, bolts, washers etc complete all as specified and as directed.

M & L in repair of water inlet and outlet geyser assembly of existing make as required at site with rubber gasket suitable for geyser of 25 / 35 ltrs capacity electric driven water storage heater with provision of housing for thermostat assembly, heating element fixing arrangement nuts, bolts and washers etc complete all as specified and as directed.

M & L in repair thermostat, switch for electric water heater storage type of capacity 25 / 50 ltr, 230 Volts of existing make of geyser complete all as specified and as directed.

M & L in repair heating element with triangular base / round base, single phase, 230 Volt, capacity 2 KW of existing make complete all as specified and as directed.

M & L in repair pressure release valve conforming to relevant IS 15mm bore suitable for fixing with GI pipe / tubing 15mm bore complete all as specified and as directed.

M & L in repair of heavy duty PVC connection (For Hot water) nylon threaded 450mm large (18") 15mm bore including brass nuts, rubber washers complete on both ends complete all as specified and as directed.

M & L in repair of heavy duty PVC connection (For Cold water) nylon threaded 450mm large (18") 15mm bore including brass nuts, rubber washers complete on both ends complete all as specified and as directed.

M & L in repair of indicator lamps round / rectangular type 230 Volt AC suitable for geyser of any capacity including providing electric connections complete all as specified and as directed.

M & L in repair water storage inner tank of stainless steel heavy duty confirming to ISI suitable for 25 ltrs capacity geyser, with provision for fixing 15mm dia galvanized air release valve complete all as specified and as directed.

M & L in repair Non return Valve 15mm dia,made up of brass complete all as specified and as directed.

Repair / maintenance / servicing to solar water heater system having a capacity 100 to 200 LPD complete with descaling / cleaning to flat plate, collector plate, solar heater water tanks, toughened solar glass panels, welding / breazing to solar tanks, Repair / rectification of leakage in inlet / outlet water tubing GI, checking and repair to electric system, Repair of water make up tank and make the system function cable after repair / servicing and rectification of the fault complete with and including replacement of minor spare parts complete all as specified and as directed.

Supply & fixing in replacement union medium grade 20mm dia complete all as specified and as directed.

Supply & fixing in repair rubber hose pipe with MS clamp of suitable size complete all as specified and as directed.

Supply & fixing in repair metal gate / globe valve 20mm dia complete all as specified and as directed.

Painting to steel structure base frame of solar water heater of 100 to 300 LPD Cap complete all as specified and as directed.

S&F in replacement float valve PVC 20 mm dia complete all as specified and as directed.

Supply & fixing in repair toughened glass panel suitable for 200 LPD solar water heater complete all as specified and as directed.

M & L in repair of electrical heating element threaded type 3 KW, single phase suitable for solar water heater complete all as specified and as directed.

M & L for fasteners 80 -100mm long for fixing of geyser of capacity upto 50 ltrs including grouting completed works in wall as per site requirement with the floor complete all as specified and as directed.

S&F in repair chromium plated CP Bib cock 15mm dia conforming to ISI complete all as specified and as directed.

S&F in repair gun metal glove / gate valve 15mm dia internal threaded with iron wheel head conforming to ISI complete all as specified and as directed.

M & L in repair of tubing GI "medium grade" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 15mm dia complete all as specified and as directed.

M & L in repair of tubing GI "medium grade" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 20mm dia complete all as specified and as directed.

M & L for fixing in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 Amps, fixing on wall suitable for geyser connection complete

M & L in repair of Rotational moulded polyethylene water storage tanks of 1000 ltr(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I. complete all as specified and directed.

M & L in repair of submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed as required 2x6.0 sq. mm + 1x 6.0 sq. mm earth wire complete all as specified and directed.

M&L for repair/Maint to desert coolers complete with and including cleaning,scrapping/ rubbing old rusted surface ,filling cavities and painting with two coat of high quality aluminium paint over a coat of red oxide primer externaly and black paint internally with synthetic enamelled paints complete with replacement of necessary nut,bolts,rubber pads for fan motors and writing MES No/unit name all as specified and directed by the Engr-in-Charge.

S&F in repair of desert cooler fan motor copper wound 90 watt,1400 RPM,3 speed,230 volt 50 Hz single phase conforming to ISI complete with fan blade and capacitor of sutitable size complete all as specified and directed.

S&F in repair of Desert Cooler submersible pumping set single phase 230 volt , 50 Hz of 0.25 HP conforming to ISI complete with lead complete all as specified and directed.

S&F in repair of desert cooler fan motor blade of existing size made out from MS heavy duty complete with key bolt complete all as specified and directed.

S&F in repair cable PVC insulated and sheathed of size 1.0 sqmm 3 core FRLS 230 volt,50 Hz conforming to ISI all as specified and directed.

S&F in repair cable PVC insulated and sheathed of size 1.5 sqmm 3 core FRLS 230 volt,50 Hz conforming to ISI all as specified and directed.

S&F in repair cable PVC insulated and sheathed of size 2.5 sqmm 3 core FRLS 230 volt,50 Hz conforming to ISI all as specified and directed.

S&F in repair of plug top 3 pin 5 Amp 230 volt 50 Hz all as specified and directed.

S&F in repair of plug top 3 pin 15 Amp 230 volt 50 Hz all as specified and directed.

S&F in repair of unsv Khas Khas/Grass pad for desert cooler Set of three peices complete all as specified.

Repair/Maint/Servicing to refrigerator/deep freezer/water coolers/AC's of any capacity and model by replacing capillary tubing,gas chargings,rectification of leakage in capillary tubing/Chiller plant/water tanks,condensing coils,repair to wiring,flushing/cleaning condensing/cooling coils/internal/External unit of split AC,greasing to blower motors,replacement of spare parts, fan belts and make refrigerator/deep freezer/water coolers/AC's in serviceable condition all as specified and directed by Engr-in-Charge. Note:Spare/Gas charging paid seperatly.

Supply & fixing in re[lacement sealed compressor unit seamless welding company manufacturer with filling of refrigerent gas conforming to ISI as under:-

For refrigerator 165/286 Ltr capacity complete all as specified and as directed.

For refrigerator 290/320 Ltr capacity complete all as specified and as directed.

For Deep Freezer 100/200 Ltr capacity complete all as specified and as directed.

For Deep Freezer 300/400 Ltr capacity complete all as specified and as directed.

For Water Cooler 40/80 Ltr capacity complete all as specified and as directed.

For Water Cooler 60/120 Ltr capacity complete all as specified and as directed.

Split/Window AC 1.5 Ton Capacity complete all as specified and as directed.

Supply & fixing in replacement condensing fan motor 1/5 HP 1440 rpm Single phase 230 Volt 50 HZ with double blade and shaft end with fan belts for windows AC/Split AC conforming to ISI of capacity 1.5/2.0 ton complete with vibration parts etc complete all as specified and as directed.

Supply and charging refrigerant 134a/412a in sealed compressor unit of refrigerator/deep freezer/water coolers/AC's of any type and capacity after flushing the complete system with carbon tetrachloride (CTC) and vacuumise the complete system with vacuum pump and testing on full load including replacement of filter,strainer all as specified and directed.

(Internal electrification)

M&L in repairs for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 6 Sqrmm for phase and neutral and one run of 6.0 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. complete all as specified and as directed. Note : Wiring shall be done in proper colour coding.

M&L in repairs for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 4 Sqrmm for phase and neutral and one run of 4 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length.complete all as specified and as directed. Note : Wiring shall be done in proper colour coding.

Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches,sockets, ceiling roses,bell push,bell electric,lamp holder,bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden/iron,round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, complete all as specified and as directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid/ 1.8mm wall thickness ISI marked including new CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified. Note : (a) wiring shall be done by using proper colour coding including making the disturb surface good (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

All as per item No 335 here in above but 5 Amp socket outlet on same board complete all as specified and as directed.

All as per item No 335 here in above but socket outlet 5 Amps independent board complete all as directed by Engr-in-Charge.

All as per Item No 335 here in above but for one 6 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size complete all as specified and as directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into existing concealed PVC rigid/steel conduit and into existing CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified. Note : (a) wiring shall be done by using proper colour coding incl making the disturb surface good. (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

All as per item No 339 here in above but One 5 pin socket outlet 5 amps on the same board complete all as specified and as directed.

All as per item No 339 here in above but One 5 pin socket outlet, 5amps, independent complete all as specified and as directed.

All as per Item No 339 here in above but for one 5 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size.complete all as specified and as directed.

Supply & fixing switch piano, flush type single pole one way 5Amp, 240 volts ISI marked complete all as specified and directed .

Supply & fixing Socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed .

Supply & fixing Switch socket outlet combined 2 in 1 , 3 pin 5 amp and 15 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fix calling bell ding dong/buzzer ,AC 230Volts single pole complete all as specified and directed.

Supply & fix stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed.

S & F for bell push , flush type single pole , 5Amp, 240 volts all as specified .

S&F Ceiling Rose 3 terminal surface type Complete all as directed.

S&F for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K Complete all as directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid/ 1.8mm wall thickness ISI marked including Modular Metal flush Boxes of any way i.e. (1 to 8 way as per site requirement) for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :- Note: suitable Modular white cover sheets with frame as specified to be provided in replacement to MS/Galvanised sunken boxes and measured & paid separately as per relevant item. Note : (a) wiring shall be done by using proper colour coding including making disturb surface good (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

All as per item No 352 here in above but 5 Amp socket outlet on same board complete all as specified and as directed.

All as per item No 352 here in above but socket outlet 5 Amps independent board complete all as directed by Engr-in-Charge.

All as per Item No 352 here in above but for one 6 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size complete all as specified and as directed.

S&F Modular switch 1 way 6A,1 module , 240 volts ISI marked complete all as specified and directed

S&F Modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and directed

S&F Modular Socket, 6A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

S&F Modular Socket 6A/16A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

S&F Modular Fan step regulator, 120W 1 module , 240 volts ISI marked complete all as specified and directed

S&F Modular bell push 6A 1 module.complete all as specified and as directed.

S&F bulk head luminaries IP65 with opal diffuser 10 watt, 230 Volts LED type complete with 10 watt LED Bulb all as directed Engr-in-Charge.

S&F LED lights fitting 1x 20W, 220V, AC batten type complete with LED tube rod 20 watts driver, holder and power factor >0.9 , SPD 2.5 KV, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and as directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Please Enable Macros to View BoQ information