PROVN OF SHEDS AT CERTAIN LOCATION AND IMPROVEMENT TO LIVING IN BLOCKS OF OFFICER MESS INCLUDING CERTAIN BUILDING AT BRD AF STATION PALAM UNDER GE (AF) GURGAON NO.1

Amount

Sch 'A' Part-I (Earth works)

Excavation of trenches by any means in soft/loose soil, not exceeding 1.5 meter wide & not exceeding 1.5 meter in depth and getting out, trimming the sides forming bottom surfaces top required level complete all as specified and as directed by E-in-Charge.

Supplying and filling in plinth, under floor , trench for cable,& foundation etc with sand , including watering, ramming, consolidating and dressing complete all as specified and directed. Note:- Compacted punned thick shall only be measured and paid

Returning, filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25cms thick in each layer of solid complete all as specified and directed by Engineer-in-Charge.

Removing surplus excavated soil to a distance n’exc 50 meters and depositing where directed at a level not exceeding 1.5 meter above the starting point all as specified and directed by Engineer –in-Charge.

Removal of debris/malwa to a distance exc 10Km but n exc 15 Km and depositing out side the MD land and as directed by Engr-in-charge.

Supply and laying well burnt sub class ‘B’ bricks, locally available in trenches for protection of underground cable complete as sepecified and directed by Engr-in-Charge.

Excavation in Post Holes (or Similar Holes) not exc. 0.50 Cum each in Soft/Loose Soil and getting out returning filling in and removing surplus Spoil to a distance not exc. 50.00 m and Make Good the Surfaces, complete all as specified and as directed.

Cutting bituminous road surface not exc 30 cm in width and getting out for taking up/laying pipe etc and including making good with CC 1:2:4, ( 20 mm graded aggregate) up to full depth complete all as directed.

Sch 'A' Part-II ( Job - Improvement to certain Bldgs ) (B/R Works)

Taking down Cement Plaster from wall and ceiling of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed. (Note :- Rate included for four storey building including scaffolding and all safety measures)

M&L for 15mm thick rendering in CM 1:4 by using manufacture/washed stone yellow/grey sand for plaster on fair faces of brick or concrete surfaces including finishing even and smooth without using extra cement all as specified and as directed by Engineer in Charge.

M&L for 15mm thick rendering in CM 1:6 by using manufacture/washed stone yellow/grey sand for plaster on fair faces of brick or concrete surfaces including finishing even and smooth without using extra cement all as specified and as directed by Engineer in Charge.

M&L for 05 mm thick rendering on concrete surfaces as in ceiling finished even and smooth w/out using extra cement in CM 1:4 by using manufacture/washed stone yellow/grey sand complete all as specified and directed by Engineer in charge.

M & L for RCC (1:1.5:3) Type A1 using 20mm graded Stone aggregate (Nominal Mix) as in beams, Coln and chajja etc. in patches including necessary form work and demolition of old exsiting RCC structure and removing the debris from the site complete all as specified and as directed by Engr-in-charge Note: - Quoted rate shall be inclusive of rate of work upto four storey

M& L for 10 mm above Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing cracking, bending soirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securong with clips complete all as specifed and directed.

M& L for 6 to 8 mm Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing cracking, bending soirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securong with clips complete all as specifed and directed.

M& L for 5 to 10 mm in striuups Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing cracking, bending soirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securong with clips complete all as specifed and directed.

Taking down old damaged grit wash Plaster including backing coat from wall of any description on brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed. (Note :- Rate included for four storey building including scaffolding and all safety measures)

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 marble chipping 5 to 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water (mixed with H2SO4 @ 5% scrubbing and washing shall continue till the stone chipping are sufficiently exposed to its natural colour) to expose the stone chippings complete all as specified. Note:- (i) (Payment for providing grooves shall be made separately). (ii) The quoted rate shall be inclusive of taking down of old grit wash plaster including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), and preparing the surface for new grit was plaster. (iii) The quoted rate shall be inclusive of necessary scafolding upto four storey building.

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

Dismantling of existing roof treatment from roof and parapet of any description and removing the rubbish and Cleaning top surfaces by brooming, wire brushing, removing grass, trees , raking out joints to receive plaster and removing debris, grass, trees etc outside the defence land complete all as specified and directed by Engineer-in-Charge. Note :- 1. Plaster shall be measured and paid separately under appropriate item of Sch ‘A’. 2. Quoted Rate of this item is inclusive of disconnect fitment at water tank or solar heater etc and refixing in the same position after compeleting of roof treatment.

M&L for 15 mm thick cement plaster by using manufacture sand in CM 1:4 on brick/concrete surfaces of roof and parapet, mixed with water proofing compound, finished even and smooth without using extra cement (Including 4 Story building) complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately.

Supply only ISI marked liquid water proofing compound complete all as specified and directed.

M&L for applying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced/torched application, over and including 85/25 industrial bituminous coat @ 1.20Kg/Sqm over and including bituminous primer @ 0.30 Ltr/Sqm on newly plastered clean and dry roof surface including sealing of joint by torch application and finishing top surface by applying Bituminous base allumininium paint two coats over APP membrene complete all as specified & as directed by Engr-in-charge.

M&L PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof coving/benching and bed block, plateform for tank etc complete all as specified and directed by Engr-in-charge

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in CM 1:4 including raking out joints including Demolition of brick masonry work, built in cement mortar of any description including rubbish of the premises complete all as specified and directed by Engr-in-charge

S&F PVC (SWR) Pipes, ISI marked 110mm in Bore (dia), Single Socketed, in any length with Rubber Ring Joints fixed to Walls or Laid in Floors, etc, including taking down /up unserviceable Pipe, complete all as specified and as directed.

S&F PVC (SWR) Bend, ISI marked suitable for PVC (SWR) Pipes 110mm in Bore (dia), jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed.

S&F 15mm Bore (dia), Chromium Plated Bib Cock with capston head, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Kitchen Sink with Drainage Board of Overall Size 915X460mm and Bowl Size 410X330X160mm, made of Stainless Steel 1.0mm thick Sheet with Plugs, Chromium Plated Waste Coupling and Washer including Bedding in Cement Mortar 1:4 to Dwarf Wall or fixing Cantilever Brackets and Connection to Pipe including Taking down unserviceable Sink and Connected Items complete all as specified and as directed by Engr-in-Charge.

S&F for Stack Clamp made of GI Channel section with 10mm dia U bolt and nut fixed to wall to hold the vertical pipe of dia up to 100/110 mm dia complete all as specified and as directed.

S&F in repair 500 ltrs ISI marked rotational moulded polyethylene water storage Three layer tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engr-in-charge .

S&F in repair 1000 ltrs ISI marked rotational moulded polyethylene water storage Three layer tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engr-in-charge .

Taking down existing water tank of capacity 500 to 1000 Ltr and refixing after necessary cleaning/water proofing treatment on roof surface including replacement of tank nipple etc complete,

S&F in repairs 20mm dia PTMT high pressure ISI marked Ball Valve with Aluminium epoxy coated rod and ball suitable to sustain water pressure from 20mm bore water, Standard of PTMT of approved make with Minimum weight 210 Gm, any Colour complete all as specified and as directed.

S&F in repairs ISI marked 20 mm Bore Gun metal globe/gate valves with iron lever fixed, screwed both ends complete all as specified and as directed by Engineer in charge.

M&L for machine cut granite stone 16-18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window sills, Kitchen platforn, floor, wall etc and similar locations of required size, approved shade, colour and texture laid over 15 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. at all levels complete all as specified and directed.

M&L for preparation of newely plastered ceiling surface and applying three coats of white wash complete and all as specified and as directed

M&L for preparing new plastered wall surface including cornices plasters by brooming down or steel wire brusing, scraping down, smoke spots and applying two coat of exterior emulsion paint 100% acrylic of approved colour and shade over a coat of primer and over 1 to 2 mm thick birla putty punning including necessary scaffolding upto 4th floor complete all as specified and as directed by Engineer-in-charge

M&L for preparing new plastered wall surface including, removing any smoke spots and applying two coat of oil emulsion over a coat of primer complete and over 2 mm thick birla putty punning as including necessary scaffolding upto 4th floor complete all as specified and as directed by Engineer-in-charge

M&L for preparation and old decorated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed.

Demolition of wall and ceiling and boards (Fibre, pulp, insulation etc.) or insulation board / slabs any thickness incl cover fillets.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but including the cost of painting with two coat of oil bound distemper with : 4 mm thick ISI marked fibre cement board (Board with BIS certification marks) Note: The contractor shall submit the Purchse voucher for Cement fibre Board.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement & fixing at site on PVC frame as per manufature instruction and standard engineering practice complete all as specified and directed.

Dismantling of floor, hearth, or wall tiling including cement mortar bedding ( but not backing) including removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L Cement Concrete 1:2:4 (20mm Graded Stone Aggregate) 25 mm thick, as in Floors, etc., and finished the Cement Concrete Surfaces Even and fair with using Extra Cement, complete all as specified and as directed.

M&L Non–Skid Ceramic Coloured Tiles, of size as approved by GE with 7-8 mm thick, Laid on Floor with neat cement slurry @ 3Kg/Sqm over and including 15mm thick screed bed of cement mortar (1:6) and including pointing in white cement with pigment to match the shade of tiles Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tiles, of size approved by GE with 7mm to 8mm thick, in skirtings/ walls/dado and other similar locations with neat cement slurry @ 3Kg/Sqm over and including 10mm thick screed bed of cement mortar (1:3) and including pointing in white cement with pigment to match the shade of tiles complete all as specified and as directed.

M&L for glazed/matt finish ceramic joint free Coloured Tiles 8 to 10mm thick, exc 0.11 sqm and n.exc 0.18 sqm each tile, in floors and skirtings/ walls and other similar locations with neat cement slurry @ 3Kg/Sqm over and including 15 mm thick screed bed of cement mortar (1:4) and including pointing in white cement with pigment to match the shade of tilescomplete all as specified and as directed.

Providing and laying light shade vitrified floor tiles in 60x60 cm x10mm sizes (thickness to be specified by the manufacturer) in floors and skirting/dado with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, jointing with grey cement slurry @ 3.3 kg/ sqm over and including 15mm thick screed bed in CM 1:6 including grouting the joints with white cement and matching pigments etc., complete all as specified and directed.

M&L for 75 mm thick, PCC (1:3:6) type C-1 using 20 mm graded stone aggregates as in path , plinth protection and paving laid in panels finished even and smooth without using extra cement complete all as specified and directed.

M&L Pre-printed/painted Chequered Cement Concrete Tiles of size 30cmx30cmx25mm thick Set and Jointed in Neat Cement Slurry 3 kg/ Sqm with Grey Cement and Pigment over and over and including Screed Bed 15mm thick in Cement Mortar (1:6) as in Path, complete all as specified and as directed.

Sch 'A' Part-III ( Job - Provn of Sheds ) (B/R Works)

M&L for Mild Steel Structural Work as in Stanchion and Column including covering plate from Steel Sections conforming to Fe-410-0 or Fe-310-0 including all necessary Welding, Bending Cold or Hot, Drilling Holes for Bolts, in any shape or size as indicated, complete all as specified and as directed.

M&L for Mild Steel Structural Work as in Rafter and Purlins including covering plate from Steel Sections conforming to Fe-410-0 or Fe-310-0 including all necessary Welding, Bending Cold or Hot, Drilling Holes for Bolts, in any shape or size as indicated, complete all as specified and as directed.

M&L for PCC (1:2:4) Type B2 (40mm Graded Stone Aggregate) in Foundations, Filling and Mass Concrete, poles/stays etc. and for fixing Posts, complete all as specified and as directed.

M&L preparing New Steel and Iron Surfaces of any descriptions, over 10 Cm in width or girth and applying Two Coats of of approved shed ISI marked Synthetic Enamel Paint over a Coat of Red Oxide/Zinc Chrome Primer, complete all as specified and as directed.

M&L for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as per manufature instructions complete all as specified and directed by Engr-in-Charge.

S & F with Min 4 mm thick PC Transluscent (min 80% light Transmission) UV Stabilised Fibre reinforced Polycarbonate sheet Clear Skylight Roofing Sheets with all fitting and fixtures as in roof or wall or other similar locations fixed with self tapping screws as per manufature instructions complete all as specified and directed.

M&L for bands , straps, supports or stays for rainwater, ventilating pipes, incuding bolts, if required hooks (stay) heavy for large gates, hook and pintle hinges large hasps and staples, chains hand made sliding bolts, clamps hold fasts wall ties hooks for hanging fans, plain agnle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles confrirming to Fe-290 Gde-E-165 complete all as specifed and directed.

Demolition of cement concrete any description in ground/floor /paving not exc. 15 cm thickness ( below or above GL) complete all as specifed and directed.

M&L for cement concrete type B1 (1:2:4) (using 20mm graded aggregate) as in coping of poles even and smooth finishing using extra cement etc all as specified and as directed.

Sch 'A' Part-IV ( Job - Improvement to Living in block of Officers mess ) (B/R Works)

Taking down Cement Plaster or old grit wash, any description on Brick Walls or on Concrete Surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed. (4th floor and scafolding)

S&f Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M& L for 10 mm above Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing cracking, bending soirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securong with clips complete all as specifed and directed.

M & L for RCC (1:1.5:3) Type A1 using 20mm graded Stone aggregate (Nominal Mix) as in slab supported on beams, columns & walls in floors, roof, canopies, landings balconines, deck slab and in shelves , complete all as specified and as directed by Engr-in-charge

M&L for prelaminated particle board of 18/19mm thick exterior grade both sides with decorative choice lamination face with veneer on both sides, fixed with screws to timber frame work of any type doors shutters including necessary jointing cleats glazing clips rubber neoprene packing handles two nos in each door hinges anodised aluminium snap beading screws complete all as specified.

Providing M.S. continious Piano hinges of over all width not less than 40 mm ISI marked IS: 3818 finished with nickel chromium plating grade I as per IS: 1068 and fixing with necessary screws etc., complete all as specified and directed.

Providing and fixing bright finished brass handles, cast type of size 75 mm with screws etc. complete complete all as specified and directed.

Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete all as specified and directed,

M&L for machine cut granite stone 16-18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window sills kitchen platfors, shelves, jamb,pillars,and similar locations of required size, approved shade, colour and texture laid over 10 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. at all levels complete all as specified and directed.

M&L 20--22 mm thick Kota stone slab flooring over and including 20 mm (average) thick base laid over and jointed with grey cement@ 3 kg/ sqm jointed with cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete complete all as specified and directed.

S&F Stainless Steel Kitchen Sink with Drainage Board of Overall Size 915X460mm and Bowl Size 410X330X160mm, made of Stainless Steel 1.0mm thick Sheet with Plugs, Chromium Plated Waste Coupling and Washer including Bedding in Cement Mortar 1:4 to Dwarf Wall or fixing Cantilever Brackets and Connection to Pipe including Taking down unserviceable Sink and Connected Items complete all as specified and as directed by Engr-in-Charge.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. Exc 500 but n exc 1000liters complete all as specifed and direcetd.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar with 1:4 ratio of cement and sand complete all as specified and as directed.

M&Lfor 15mm thick rendering on brick or concrete surfaces in internal surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L rendering 15mm thick in cm 1:6 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement incl taking down cement plaster or concrete, brick surface and raking out hacking for key scrubbing down with water to receive plaster. Note: The work to be executed at the height of 12 to 15 mtr the rate for necessary scaffolding deemed to be included in the qouted rate.

S&F 500 Litre capacity of ISI marked rotational moulded polyethylene water storage tank (Cylindrical vertical with closed tap)(three layer) hoisted and fixed in position including fixing of 20 mm dia ISI marked GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia ISI marked GI pipe medium grade overflow pipe 600 mm long with fittings and including dismantling of existing tank complete all as specified and as directed.

S&F 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastec ball screwed for iron pipe and fixed complete all as specified and directed.

Taking up or down existing steel tubing/PPR pipe of any size and connections including cleaning for refixing or removal to store complete all as specified and as directed

Supply & fixing, ISI marked 15 mm dia galvanized iron tube medium grade with all fittings such as bends, elbow, socket, reducer etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

Supply & fixing, ISI marked 20 mm dia galvanized iron tube medium grade with all fittings such as bends, elbow, socket, reducer etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

Material and labour applying two coats of Oil Bound Distemper over a coat of alkali resistant primer and 1 to 2mm thick wall care putty including preparation of newly plastered wall surfaces complete all as specified and directed.

Material and labour applying two coats of Oil Bound Distemper over a coat of alkali resistant primer and 1 to 2mm thick wall care putty including preparation of newly plastered ceiling surfaces complete all as specified and directed.

M&L preparation of old decorated surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efforescent salts and trading oil and greasy spots etc and applying one coat of distemper oil emulsion and ceiling 1 to 2 mm thick care putty on old decorated plastered surfaces of ceiling complete all as specified and directed. Note :- All holes/cracks to be filled with white putty and making good to old surface

M&L preparation of old decorated surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efforescent salts and trading oil and greasy spots etc and applying one coat of distemper oil emulsion and 1 to 2 mm white putty on old decorated plastered surfaces of wall complete all as specified and directed. Note :- All holes/cracks to be filled with birla putty and making good to old surface

Providing and fixing aluminium work with following for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per specified and directed. (Glazing, paneling to be paid for separately) :

(A) For Frame : Powder coated aluminium (minimum thickness of powder coating 50 micron)

(B) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exceeding 1.5 sqm and but n,exc 4 sqm each for archives soffits, linings window boarss etc complete all as specified and directed.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per specified and directed. : 5.5mm thick sheet glass of ordinary quality in square

S&F ISI marked 12mm thick prelaminated particle board, interior grade,prelaminated both side with decorative choice lamination, fixed with screws in timber frame work or as in cubicals, partition or cupboards or aluminium work of partition, door, cubicals , shelves, cupboard etc., complete all as specified and as directed.

Providing and fixing double action hydraulic floor spring With stainless steel cover plate minimum 1.25 mm thickness of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete all as specified and directed.

Providing and fixing bright finished brass 100 mm mortice lock with 4 levers and a pair of lever handles of approved quality with necessary screws etc. complete all as specified and directed.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid (W.C. pan with ISI marked white solid plastic seat and lid,with Recessed Bottom closed pattern and Cover including Mild Steel Chromium Plated Aluminium Hanging Device and fixed-in-repairs and 10 litre low level white P.V.C. flushing cistern, including flush pipe, conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required in C:M(1:3) and fixing the cistern with a Pair of Cast Iron Brackets duly synthetic enamel painted Painted/Erecting Stand complete all as specified and directed

S&F Vitreous China 600mm Size Oval Shaped Wash Hand Basin White with Granite Counter Top supported with 40mm thick Cudappah Stone horizontal and vertical Stone of Suitable Size including vertical granite Strip with Moulding/Rounding on exposed edges, with 32mm dia Brass Chromium Plated Waste Fitting, UPVC Bottle trap, 32mm dia UPVC Waste Pipe, including Cutting Chase cutting in wall and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including Taking down Unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed.

S & F in repair vitrous china half stall urinals white or colour as directed complete including fixing all accesary such as Brass CP waste fitting, Spreader, Brass CP extension rod and Brass CP screw etc. pointing around urinal and provision of waste pipe PVC suittable for urinal pot complete all as specified and directed.

S&F Angle Stop Cock 15mm Bore (dia), Chromium Plated, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs complete all as specified and as directed. Make Cera/Jaguar/Marc.

S&F Bib Cock 15mm Bore (dia), fency type Chromium Plated Long Body Bib Cock, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs, complete all as specified and as directed.Make Cera/Jaguar/Marc.

Dismantling of floor, hearth or wall tiling including cement morter bedding (but not backing), removing serviceable tiles to the stores and rubbish off the premises.

M&L Non–Skid Ceramic Coloured Tiles, of size as approved by GE with 7-8 mm thick, Laid on Floor with neat cement slurry @ 3Kg/Sqm over and including 15mm thick screed bed of cement mortar (1:6) and including pointing in white cement with pigment to match the shade of tiles Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tiles, of size approved by GE with 7mm to 8mm thick, in skirtings/ walls/dado and other similar locations with neat cement slurry @ 3Kg/Sqm over and including 10mm thick screed bed of cement mortar (1:3) and including pointing in white cement with pigment to match the shade of tiles complete all as specified and as directed.

M&L for replacement of 100mm CI floor/nahani trap with steel grating including jointing and breaking/ dismantling any type of floor and making good cement concrete to the B-1 (1:2:4) and testing after repairs and taking down existing trap etc complete all as specified and directed by Engr-in-Charge

M&L in fixed in repairs for Steel Plate Rack size 0.60*0.90 m with 1 mm thick Steel plate complete all as specified and directed by Engr-in-Charge

S&F 75mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints fixed to walls complete all as specifed and directed

Sch 'A' Part-V (E/M Works of all jobs)

Taking down copper/aluminium point wiring (light points) complete, including fixtures and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed

Taking down copper/aluminium submain wiring complete, including conduits of any kind, and removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed

Taking down main switches, distribution boards etc of any type and capacity along with the existing boards, and removing the same from site and making good the disturbed surfaces/portion of walls etc. all as directed.

M & L for point wiring (concealed on wall & surface/concealed on cealing) for one light/fan/exhaust fan controlled by one modular switch one way in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 1.5 sqmm FRLS PVC insulated & unsheathed, stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed

M & L for point wiring (concealed on wall & surface/concealed on cealing) for 5 Amps 5 Pin socket outlet on the same board in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 1.5 sqmm FRLS PVC insulated & unsheathed, stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed.

M & L for point wiring (concealed on wall & surface/concealed on cealing) for one 5 pin, 5 Amp socket outlet on independent board not below the switch board of the light point in the same vertical plane in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 1.5 sqmm FRLS PVC insulated & unsheathed, stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed.

M & L for point wiring (concealed on wall & surface/concealed on cealing) for one 5 pin, 15 Amp socket outlet on independent board in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 2.5 sqmm FRLS PVC insulated & unsheathed, stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed.

M & L for point wiring (concealed on wall & surface/concealed on cealing) for point controlled by two 2 - way switches in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 1.5 sqmm FRLS PVC insulated & unsheathed, stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed.

Supplying and fixing 3 pin, 5 A ceiling rose on the junction box/ wooden block including connections etc. as required complete all as specified and as directed .

Supplying and fixing modular switch one way 6 Amps , 1 module on the existing modular plate & switch box including connections but excluding modular plate etc. as required complete all as specified and directed

Supplying and fixing modular socket 6 A-2/3 Pin combined 2 module on the existing modular plate & switch box including connections but excluding modular plate etc. as required complete all as specified and directed

Supplying and fixing replacement of modular switch two way 6 Amps , 1 module on the existing modular plate & switch box including connections but excluding modular plate etc. as required complete all as specified and directed.

Supplying and fixing twin modular socket heavyduty out let 6 pin 6/16 Amps 2 module on the existing modular plate & switch box including connections but excluding modular plate etc. as required complete all as specified and directed.

Supplying and fixing of modular switch one way 15/16 Amps, 240 V , 1 module on the existing modular plate & switch box including connections but excluding modular plate etc. as required complete all as specified and directed. .

Supplying and fixing ISI marked, 120 W, two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required complete all as specifed and directed

Supplying and fixing 1 or 2 Module (75mmX75mm), GI box including modular base & modular white cover plate of 1 or 2 Module for modular switches in recess/surface etc. as required complete all as specifed and direceted.

Supplying and fixing 3 Module (100mmX75mm), GI box including modular base & modular white cover plate of 3 Module for modular switches in recess/surface etc. as required complete all as specifed and direceted.

Supplying and fixing 6 Module (200mmX75mm), GI box including modular base & modular white cover plate of 6 Module for modular switches in recess/surface etc. as required complete all as specifed and direceted.

Supplying and fixing 8 Module (125mmX125mm), GI box including modular base & modular white cover plate of 8 Module for modular switches in recess/surface etc. as required complete all as specifed and direceted.

S&F Modular type blank plate , 1 module as specified.

Taking down of serviceable ceiling fans/wall mounted fan/Exhaust fan of any size and shape and refixing the same on same position including cleaning with soap water for removing grease, dirt, dust, smot with satisfaction of engr-in-Charge etc and mentioning MES number with black japan paint of size not less than 2 cm in height complete all as specifed and directed. Note:- The Engr-In charge shall prepare a report for handing over of fan with existing MES number and submit along with RAR for payment to contractor. The before and afterwards photograph shall aslo be kept in record and shall be furnished to E8 section on demand.

Taking down and Refixing of same Fluorescent tube light fitting of any type after the repair of the buildings on the same location complete all as specifed and directed.

Supply and fix PVC ventilating fan AC single phase 230/240 volts of size 200 mm sweep having revolution not less than 1200 RPM and air delivery not less than 450 cum/hr with louvers and connecting up including provision of suitable cable from ceiling rose to connector to exhaust fan also including making suitable size hole on wall/window and making good as per site requirement complete all as specified and directed

Supply & fix sheet metal enclosure for 220 volts 20 Amps with a three pin and earth plug top with socket and one single pole MCB 20 amps complete as well as specified and directed.

Supplying and fixing 08 way double door, single pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB/RCCB/Isolator) complete all as specified and directed.

Supplying and fixing of 4 way (4 + 12), Double door surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) complete all as specified and directed.

Supplying and fixing 5 A to 32 A rating, 240V, 10 kA, "B" curve, miniature circuit breaker suitable for inductive load of Single poles in the existing MCB DB complete with connections, testing and commissioning etc. as required complete all as specifed and directed.

Supplying and fixing 40 A rating, 240V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single poles and neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required complete all as specifed and directed.

M&L for concealed sub main wiring three run of 06 sqmm FRLS, PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. (For AC connection ) Note- (a) Two runs of single core cable with one run of earth continuity cable including 20mm dia PVC Medium grade ISI marked conduit and its accessories will be measured and paid as one unit). (b) Quoted rate shall be inclusive of making disturbed surface good to wall/floors as existing surface.

M&L for concealed sub main wiring three run of 04 sqmm FRLS PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. (For AC connection ) Note- (a) Two runs of single core cable with one run of earth continuity cable including 20mm dia PVC Medium grade ISI marked conduit and its accessories will be measured and paid as one unit). (b) Quoted rate shall be inclusive of making disturbed surface good to wall/floors as existing surface.

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick electrode, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to 4 mm dia galvanized earth wire by means of bolts, nuts, check-nuts and washers of galvanized iron or steel all as shown in electrical plate No 5 (duly protected with 15 mm dia light grade GI pipe upto 7.5m from the earth plate) and connected to GI steel earth plate including charcoal, dust, common salt, necessary excavation in soft/loose soil, returning, filling in and removal of surplus soil to a distance not exceeding 50 m from the starting point, watering pipe 20 mm bore GI tube of light grade treated with 1 No PGI funnel, pit of PCC 1:2:4 type B-1/ RCC 1:2:4 type B-1, pit cover 75 mm thick reinforced with 6 mm dia bars @ 75 mm c/c both ways and with MS handle 12 mm dia connected to earth test point including testing complete all as specified and directed.

S&F 4 ft 18/20 watt 6500 K Decorative ultra slim aluminium LED lighting fixture with high lumen output, environmental friendly, energy complete all as specified and directed.

S&F 2 ft 09/10 watt 6500 K Decorative ultra slim aluminium LED lighting fixture with high lumen output, environmental friendly, energy complete all as specified and directed.

S&F 1 x 42 watt 2'X2' Ultra modern designed architectural LED luminaire which provides soft-light and glare free symmetrical illumination suitable for Armstrong/Grid ceiling complete with all accessories internally connecting up with three core flexible copper cable of suficient size, 240 Volt complete all as specified and as directed.

Supply & fixing ISI marked exhaust fan AC single phase 230/ 240 V AC of size 300 mm sweep 3 blade and having 1400 RPM with suitabl size of louvers including making hole and including making good of the wall as per existing surface complete all as specified and directed .

Supply and laying or fixing XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cable (H/D) earthed cable aluminium conductor, 1100 volts grade with standed complete all as specified and directed for 10 sq. mm, 4 core nominal cross section in service connections complete all as specifed and directed.

Shifting of steel tubular poles by using special T&P and re-erection the same pole within unit area complete all as specified and directed. Note : Civil work will be measured and paid separately

Supply and fixing LED flood light 100 watt LED 6500 K 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specifed and directed.

M&L for sub main wiring of two run with 2.5 Sqmm single core PVC insulated, FRLS, flexible multi stranded copper conductor cable 1100 volts grade, drawn through and including PVC conduit pipe of size 20 mm medium grade and accessories of suitable size and fixed on wall/ceiling including one run of 2.5 Sqmm single core PVC insulated, FRLS , flexible copper cable as earth continuity conductor in green color all as specified and as directed.

Supply & fix Air Circulator fans of 450mm sweep with revolution not less than 1400 RPM having ossiclation degree of 90 degree, 230 volts, single phase, 3 speed, low noise motor, with stong air throw, including suitable mounting arrangements as per manufature instructions complete all as specified and directed.

Supply, installation, commissiong and testing ISI marked 230 volts single phase large spece air cooler having 8500 m³/hr air delivery, weather resistance body, high efficiency cooling pads, wide water inlet, five level speeds, locakabe heavy duty wheels,125 ltr water tank capacity and 525 mm dia fan diameter with one year warranty on letter head of contractor complete all as specified and directed.

Suppy and fixing 3 pin 15 Amps switch socket combination, box type multipurpose 2 in 1 type (3 pin 5 Amps and 15 Amps) all as specified and directed.

Sch 'A' Part-VI (Rifle Racks)

Supply and fixing of Theft -proof Rifle rack, single tier typr, fixed butt, suitable for accommodating 20 Nos. of AK-103 rifles without amunation box with min dimension of 72 inch x 16 inch x 35 inch complete all as specified and directed. Make: Riflok (kaypee & Coo) or as equivalent approved.

Schedule of Credit

POOJA ENTERPRISES