Development of Muthupettai (New Site) mangrove forest area in Thiruvarur District as a Tourist Destination with various facilities and amenities.

Amount

Civil Work

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils such as ordinary soil and hard gravelly soil to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Damp proof course with Cement Mortar 1:4 (One Cement and Four crushed stone sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used, finishing and curing etc. complete complying with standard specification.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For Circular Columns etc.,

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation and Basement

For superstructure in Ground floor

Supplying, fabricating and placing in position TMT rod grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar 1: 5 (one cement and five sand) using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" for foundation and basement including curing, etc., complete complying with standard specification.

For Foundation and Basement

Plastering in cement mortar 1:5 (One cement, and five sand) 12mm thick including curing and finishing neatly complying with standard specification and as directed by the Corporation Officers etc. complete.

Painting the newly plastered wall surfaces two coats with approved weather proof Exterior Emulsion paint over etc., complete complying with standard specification.

Supply and erection of M.S Angle pole of size 50mmx50mmx6mm in the equired length including provision of anchorage clamp and making holes for fixing chain link fencing , erection in true alignment with necessary foundation concrete including cost and conveyance of all materials , labour but excluding the cost of concrete etc...complete complying with standard specification.

Supply and fixing of chain link fencing (50mmx50mmx10 Gauge) with necessary M.S angle post of size 50mmx50mmx6mm at every 3.0M centre to centre fixing in P.C.C1:2:4. The top and bottom to be fixed with M.S flat of size 25x3mm horizontally on both sides including provision of holes in M.S flats and fixing M.S bolt and nuts etc., complete. The rate is including cost of all materials, labour charges and excluding cost of M.S angle and P.C.C 1:2:4 etc., complete.

Painting two coat with ready mixed synthetic enamel paint of approved quality and colour over new iron works including cost and conveyance of all materials, labours and etc..., complete complying with standard specification.

Fabricating and supplying fixing in position of steel works as detailed and as directed at all levels using MS hollow section, etc.of various sizes and other structural steel sections conforming to IS 2062 including straightening, cutting, fabricating, welding, bending to shape, bolting, fixing in position, welding, embedding in wall / concrete and finished the surface neat by grouting. Rate shall include for painting with two coats of dark grey colour synthetic enamel paint over a coat of Zinc chromate primer, etc. complete, as directed.

Roofing with best quality Aluminium roofing sheets of 0.71mm thick over the existing C.W purlins by fixing the sheets supported with C.W reaper of Size 50mm x40mm on top at a spacing of not more than 0.60m c/c including cost of SS bolt with washer sets of size 125mmx6mm dia at a spacing of 0.40m c/c, including charges for the conveyance of materials & labours for the work as directed by the corporation officers complying with standard specification.

Supplying and fixing in position of 10mm thick Gyp board FALSE CEILING arrangements with aluminium anodised ' T' Section and 'L' angle frame work of grid size 600x600mm with aluminium T section and 'L' angle of size 25x25x2mm thick and the same is supported @ suitable intervals by adjustable type 6 mm dia MS rod with suitable threaded nuts suspended rods hung from ceiling at 120 cm c/c in both directions and fixing Gyp board in the Grid so as to give a seat to false ceiling including painting the 6mm dia MS rod etc.,complete complying with standard specifications. Necessary opening and arrangements for fixing electrical fitings should be provided with suitable frame work etc.complete

Fabricating supplying and fixing in position of used Shipping Containers Size : 6M x 2.40M x 2.60M Main Entrance Door size : 0.9M x 2.13M 1 No A dead light Steel outside Safety door will have with altrop lock system with Door Top a rain gutter. Counter Window 3.05M x 0.9M Up till Flap Door. Internal Panelling : 50mm x 25mm x 1.6mm Metal Square Tube frame with 50mm Density Rockwool Insulations and panelled with 8mm Cement Fiber Board Over the patti & paint finish. Floor: Contaier Original floor over the size (600mm x 600mm) tiles finishing. Painting: Two coat of enamel paint finish (as per required colour). Container Roof top:Metal structure plat form with tiles floor finishing & 0.9M height safety hand rails. Staircase:Metal 0.9m height safety hand rails.

Steel Container for Café

Steel Container for Ticket Counter & Store

Fabricating, supplying and fixing in the position of security cabin container of size (1.20M x 1.20M): 50mm x 50mm x 2mm MS Square tube section for , floor over which the 18mm plywood board fixing, 1.6mm corrugated MS sheet for wall & Roof. Main Entrance Door size: 0.9m x 2.13m size 1 No a dead light steel outside safety door will have with altrop lock system with door top a rain gutter. MS Window: 0.6M x 0.9M size 3 No's window top a rain gutter & inner aluminium sliding widow each. Internal Panelling: Insulation 35mm x 35mm wooden frame with 25mm thick thermacole insulation and panelled with 6mm MDF board on roof & wall panels with joint wooden beading finishing and wiriting pad-1 No. Painting: One coat zinc primer & 2 coat enamel painting (as required colour). Form: 18mm plywood fixing over the vinyl matt flooring. Electrical: 15watts LED panel light - 1No. Power points - 2Nos. Out side Light - 1Nos.

Fabricating, supplying and fixing in the position prefabricated Toilet Container Size 4.-90m x 1.20m x 2.60m: 100mm x 100mm x 3mm Square tube on corner post 100mm x 50mm 2.5mm Rectangular tube on bottom rail 60mm x 6mm x 2.0mm rectangular tube on top rail 1.6mm MS corrugated sheet for side & roof flooring 80mm x 40mm x 2mm MS rectangular tube cross membrane over the 18mm cement fiber board for flooring top 4 corner lifting hooks provision. MS Door with ventilator 4 Nos. Internal Panelling: 50mm x 25mm x 1.6mm metal square tube structure frame with 50mm density rockwool insulations and panelled with water proof 4mm ACP sheet with joint beading finishing. Accessories: EWC and Heath Faucet - 4Nos, Wash Basin with Tap - 4Nos, All water inlet & waste water out let project to be container outside. Floor: Container 18mm Cement fiber board floor over the size 0.3m x 0.3m antiskid tiles finishing. Electrical: 15 watts LED panel light - 4 No's, Out side Light - 4 No's. Painting: External Surface Pinting - 1 coat of Antirust primer inner & outer over the 2 coat enamel paint finishing.

Drilling Single Under Reamed Pile 600mm dia, Providing and installing Cast in situ single under Reamed piles of specified dia and length below pile cap in cement concrete piles using the ready mix concrete of M25 Grade to carry a safe working load not less than.The specified, excluding the cost of steel reinforcement but including the cost of RCC, shoe and the length of pile to be embedded in the pile cap etc., all complete.(Length of pile for payment shall be measured from top of shoe to the bottom of pile cap).

Supplying and fixing of 75mm dia horizontal hand rails supporting with both sides using 150mm x 150mm country wood vertical supports, 75mm dia verticals top supporting with 75mm dia horizontal bamboom railing bottom supporting with 150mm x 150m country wood beams.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing of wooden truss with vertical wooded piller supports, using 200mm x 200mm contry wood scantling wooden post, for truss using 150mm x 150mm contry wood main rafters and 100mm x 100mm country wood purlins for supporting thatched roof.

Supplying and laying of thatched roofing using 775mm x 600mm UBUD-AGED COLOUR_WR-JE-2301 Thatches Installed at 9.5" and thatch ridge, thatch starters over with 15mm Cement sheet rates inclusive of 3mm waterproofing by torching.

Clearing and Removing of Light Jungle clearing away from the site and levelling the site etc. complete.

Supplying and FILLING GRAVEL Supplying and filling in 'foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Supplying and laying of Interlocking Paver Block Stone 80mm thick. Over a base layer of 100mm thick crushed stone sandfilling including. Cost of all materials and Labour charges etc., complete

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 600mm x 600mm x 100mm in Cement Concrete 1:2:4 (One cement, Two crushed stone sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed

Providing Turffing of Mexicon Grass. The existing soil to be removed filled with suitable to a depth of 3” of Red soil and compost. The soil to be prepared by rough dressing, fine dressing and making grass mounts, After that fertilizer and Gypsum for neutralizing soil PH over the soil bed. The gross to be free from White Ants by applying pesticides like phorate and Monocrotophos. The chemical and mechanical weeds to be controlled by applying foliar spray.Tabernaemontanadivaricata and clerodendrem plants. A pit of size 1’-0”x1’-0”x1’-0”to be digged, refilled with Red earth, sand compact to be added to improve the fertility and to increase the water holding capacity. The Basal application of fertilizers like Super phosphate, Complex fertilizers and Neem cake after Planting of Plants.Then Gypsum (CaSo4 2H2O) to be added for reducing the Alkalinity of the soil The rate is including cost of all materials, labour for plantation, and conveyance to site and maintenance for three months.

Paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (one cement three crushed stone sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Supplying and fixing in position of the Granite Stone Benches of Size 1.50 M length x 0.60m ,width x 0.10m thick and legs of 0.90m height x 0.60m width x 0.10mm thick.The rate is inclusive of cost of all materials and labour charges etc complete with necessary earth work excavation,mat concrete with CC 1:5:10 and foundation concrete with PCC 1:2:4. as directed.

Supplying and fixing in position of the Circular Granite Stone Center Table of size 0.90mtr dia x 0.10m Thick x 0.90 heigh (1No) erected over a 3 nos of 100mm dia stone pillars embbeded properly in PCC 1:2:4 to a depth of 0.60mtr with Curved Granite Stone seaters of size 1.50m x 0.45m x0.10mm thick (3 NOS) ,For one unit.The rate is inclusive of all materials and labour charges etc complete with required earth work excavation, mat concrete in PCC 1:5:10 and necessary foundation concrete with PCC 1:2:4 for fixing the stone tables and seaters as shown in the drawing enclosed and as directed.

Supplying and fixing of Patio Umbrella (Polycorponate sheet} of size 2.70M dia fabricated using MS square hollow tubes of size 50mm x 50mm x 3mm for Frames and the MS Centre pole of 2.10M height and 100mm dia. All the new iron frame works to be finished with two coats of best approved first quality and colour of synthetic enemel paint over one priming coat of zinc oxide in all floors including cost of materials and labour charges etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the departmental officers before use on works.)

Plastering in cement mortar 1:5 (One cement, and five sand) 12mm thick including curing and finishing neatly complying with standard specification and as directed by the Corporation Officers etc. complete.

Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the TWAD Board Officers) including construction of mud pit.

Drilling of 150 mm pilot bore

i. Upto 60m Depth ending below ground level

Reaming 140/150 mm dia pilot bore to 300mm dia bore as directed by the TWAD Board Officer.

Supply of PVC casing pipe 200m dia with 10mm wall thick at site the mean outer dia of the piples shall be of 229mm dia and the maximum mean outer dia 229.50mm for erecting in the borewell as directed by the department officers and as per the standard specifications.

Labour Charges for inserting PVC Casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC Couplers with Cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the executive engineers of TTDC officers

Supply and fixing bail plug having length of 0.45metre from medium class pipe as per IS and as directed etc., complete.

Providing water sample chemical analysis as directed by the corporation item

Supply and delivery and fixing of clear water vertical wet type Three phase 3 hp submersible pumpset suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star rated capableof discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balenced bronze or cast SS impeller, brass screws and dynamically balenced bronze or cast SS impller, brass screws and CI FG 200 grade pump coupled to a continues rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 / IS 1995 as amended there after, suitable for operation in AC three phase 415V+/-10%, 50HZ +/-5% (PWD SSR Annxure No.6 of Sl.no:406)

Supply and laying of FRLS PVC insulated 3 core 4 sq.mm Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days. (TWAD Page No.308, 17c)

Supplying and fixing of HDPE pipes 50mm dia for Sub-Mersible pump in bore well with ISI mark of best quality conforming to IS Specification (Below ground level)including earth work excavation and refilling etc.,complete SSR page: 105

Supply and Fixing of Nylon Rope for borewell (SSR Sl.no:411) as directed etc., complete.

Supplying and filling of following guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

40mm guauge HBGS stone jelly

25mm guauge HBGS stone jelly

20mm guauge HBGS stone jelly

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Departmental officers before use on works.

15mm dia PVC pipes

20mm dia PVC pipes

25mm dia PVC pipes

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs,clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

Above Ground Level

15mm dia UPVC pipes

20mm dia UPVC pipes

25mm dia UPVC pipes

32mm dia UPVC pipes

40mm dia UPVC pipes

50mm dia UPVC pipes

Below Ground Level

15mm dia UPVC pipes

20mm dia UPVC pipes

25mm dia UPVC pipes

32mm dia UPVC pipes

40mm dia UPVC pipes

50mm dia UPVC pipes

Supplying, laying and jointing CPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

15mm dia CPVC pipes

20mm dia CPVC pipes

25mm dia CPVC pipes

Supplying and fixing in position best quality S S 304 sink of of 600 x 450 x 200mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia PVC Pipes

110mm dia PVC Pipes

160mm dia PVC Pipes

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements as directed etc., complete complying with standard specifications.

UPVC ELBOW

50mm dia

40mm dia

32mm dia

25mm dia

20mm dia

15mm dia

UPVC TEE

50mm dia

40mm dia

32mm dia

25mm dia

20mm dia

15mm dia

UPVC UNION

50mm dia

40mm dia

32mm dia

25mm dia

20mm dia

15mm dia

UPVC BEND

50mm dia

40mm dia

32mm dia

25mm dia

20mm dia

UPVC COUPLER

50mm dia

40mm dia

32mm dia

25mm dia

20mm dia

15mm dia

UPVC REDUCER

50mm x 40mm dia

40mm x 32mm dia

32mm x 25mm dia

25mm x 20mm dia

20mm x 15mm dia

UPVC REDUCER ELBOW

50mm x 40mm dia

40mm x 32mm dia

32mm x 25mm dia

25mm x 20mm dia

20mm x 15mm dia

UPVC REDUCER TEE

50mm x 40mm dia

40mm x 32mm dia

32mm x 25mm dia

25mm x 20mm dia

20mm x 15mm dia

UPVC HEX NIPPLE

50mm dia

40mm dia

32mm dia

25mm dia

20mm dia

15mm dia

Construction of INSPECTION CHAMBER 0f internal clear size 0.60m(L) x0.60m(B) x0.60m(D) including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Supplying anf fixing Heavy duty man hole cover 600mm x600mm Heavy duty man hole cover with frame as directed etc., complete.

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

SD Tap

Pillar Tap

Swan Neck Tap

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

Supply of factory assembled 62.5 KVA "KIRLOSKAR" Make diesel engine Model 4R810TA G1, three cylinders, liquid cooled, turbocharged with after cooler, developing 83 hp @ 1500 RPM. 4R810TA G1 is Inline, electric start, compression ignition, 4 stroke, designed to run continuously at 1500 RPM confirming to IS 10002, ISO-3046, BS 5514 standard. Diesel Engine will comply with present CPCB-II norms. The diesel engine will comprise of following: Dry type air cleaner, Exhaust Silencer suitable for canopy, Expansion bellow, Lube Oil cooler, Lube oil filter, Fuel Filters, Radiator with pusher type fan and mounting, In-line mono block fuel injection pump, Mechanical governor and fuel feed pump, Flywheel with starter ring and bell housing suitable for close coupling, 12 Volt electric starter motor, Battery charging alternator, Microprocessor based KG934 Controller mounted on the Controller Panel, Protection System for Low lube oil pressure & High water temperature and having dimension of 2908 x1100x1835 (L*W*H) etc., complete.

Supply, fabrication and erection of 100 Amps 3 Phase cubical type changeover panel made out of 14/16 SWG CRCA sheet steel enclosure, welded construction wall mounting type with grey powder coated suitable mounting in angle iron frame on wall with comprising of following arrangements etc., complete.

Providing chemical earthing as per the ISI specification with an earth electrode of 3.0mt class 'B' GI pipe with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 25mm x 6 mm tinned copper flat with necessary clamps / supports on wall/ floor/ground for earth connection.

Fabrication, Supply and erection of 125 Amps LV floor mounted distribution cubical type panel board with lock & key arrangements having the following specifications with sheet steel enclosed, Dust & Vermin proof, floor Mounting pattern, cubical type panel made out of outer 1.6mm, inner 1.2 mm sheet steel with following switch gears and phase indication LED lamps including transportation etc., complete. Incomer: 125 Amps FP Switch – 1 No Outgoing: 63 Amps FP Switch – 8 Nos BUS BAR Phase : 50 x 6mm 3 run copper flat Neutral: 25 x 6mm 1 run copper flat

Supply and laying of 3½ x 70 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and laying of 3½ x 35 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and laying of 3½ x 25 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and fixing of brass cable gland for 3½ x 70 sqmm PVC armoured LTUG cable with earth connection etc., complete.

Supply and fixing of brass cable gland for 3½ x 35 sqmm PVC armoured LTUG cable with earth connection etc., complete.

Supply and fixing of brass cable gland for 3½ x 35 sqmm PVC armoured LTUG cable with earth connection etc., complete.

Supply and providing cable end termination of 3½ x 70 sqmm PVCLTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and providing cable end termination of 3½ x 35 sqmm PVCLTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and providing cable end termination of 3½ x 35 sqmm PVCLTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and fixing of 6 Mtr GI steel tubular pole for street light with base plate of (250 x 250 x 6mm) having dimension of 76.10mm OD x 3.65mm Thick x 6000mm Length, with 1 Mtr cross arm of 32mm GI pipe for fxing of 120 Watts LED Street light fitting with inbuilt of 10 Amps 4 pole MCB suitable to mount on 1 Mtr depth concrete foundation etc complete.

Supply and fixng of TNEB meter board suitable for 3 phase 200A service connection made up of suitable angle iron frame work of size 3 feet x 2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 3 feet x 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 200A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 19/16 PVC insulated copper wire with earth connection complete.

GST at 18%

SRI EZHUMALAIYAN CONSTRUCTION