SPL REPAIR AND ALLIED WORKS TO BLDG NO MES P-81 AND SM-20 AT SE FALLS AND PROVN OF HARD STANDING ALONGWITH DRAINAGE WK NEAR BLDG NO SM-20 UNDER GE SHILLONG

Amount

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position as in framed work, complete all as specified and directed by Engr-in-Charge.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing specified complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Demolition of precast concrete articles and precast concrete block walling including all quoins, arches, pillars, etc built in cement mortarof any description not other specifically provided for etc and removal of rocks/debris to a distance not exc 50 mts and depositing where directed at a level n exc. 1.5 m above the starting point.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but n exc 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area not exc 1.5 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

S & F 0.50 mm thick pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

M & L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240.

M & L for preparing surface of steel & iron work of any description exc 10 cm width or girth & applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M & L for pre-cast PCC solid block (1:3:6) type C-1 using 20mm graded stone aggregate with solid block exc 10 cm in width and built in CM (1:6), complete all as directed by Engineer-in-Charge.

M & L for precast cement concrete solid (1:3:6) type C-1 using 20mm graded stone aggregate building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar (1:6), complete, in walls, complete all as directed by Engineer-in-Charge.

M & L including wastage of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

S & F mild Steel (TMT) bars 10 mm dia and over cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality .

S & F mild Steel (TMT) bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality.

M & L for reinforced Cement concrete Type B1 1:2:4 (20 mm graded aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span .

M & L for 15 mm thick rendering in cement mortar 1:4 fair faces of brick work or concrete surfaces finished even and smooth without using extra cement all as specified and as directed.

M & L for rendering 10 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified directed.

Preparing newly plastered surfaces of wall and applying with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) over 1 mm thick wall care putty complete all as specified and directed.

M & L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of chalk whitening primer over 1 mm thick wall care putty complete all as specified and directed.

M & L for 100 mm thick cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base.

M & L for non - skid ceramic tiles, (first quality of approved class, colour and design/shade) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sq m but not exceeding 0.18 Sq m, as in floor surface etc. over & including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

All as per above item No. 22 but on vertical surfaces over and including 10 mm thick rendering in CM 1:4 , complete all as specified and as directed.

M & L for outdoor light shade Vitrified paving tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.06 sqm but n exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

All as per above item No. 24 but on vertical surfaces over and including 10 mm thick rendering in CM 1:4 , complete all as specified and as directed.

M & L for avant-garde ceramic tiles (digitel in beehive shape) 300 x 450 x 7mm thick on vertical surfaces such as wall cladding, dado, skirting etc., with dark border in middle set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering as backing coat in cement mortar 1:4, complete all as specified and as directed.

S & F 4 mm thick E-board non asbestos fibre cement building boards false ceiling (Classic) including galvanised colour coated snap grid frame for false ceiling, size of grid 605 X 605mm fixed with 1.6 mm dia GI wire suspenders one end tied to roof members and other end connected to main tee of grid framework by means of 4mm dia adjustable "J" hook consisting of two Nos washers and two nuts at 1.2 mtr centres, size of main tee 38mm X 25mmX 1.4mm, cross tee 38 mm X 25 mm X 1.4mm, angle along walls 38 mm X 25mm X 2.0 mm etc complete all as directed.

M & L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and as directed.

M & L for 18-20 mm thick granite (of any type) tiles machine cut, in skirting/dado laid over 10 mm thick rendering as backing coat in cement mortar 1:4 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified.

M & L for providing edge moulding to 18-20 mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc complete all as specified and directed.

M & L for framed work ornamental and intricate design such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F powder coated (min thickness of powder coating 50 micron) anodised aluminium frame for doors, windows , ventilators plain or sliding type with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

S & F Powder coating anodised window and ventilator shutters side hung/sliding type without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws ,anodised aluminium fittings such as peg stays 150 mm long(1 no) hinges type B-21 100 mm long (2 no) suitable handle (1 no ) complete all as specified and directed.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

S & F 1.25 mm laths of steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: gear operated type with chain wheel and hand chain complete all as specified and directed.

S & F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

M & L for solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

S & F aluminium guide rail three track having two PVC wheel 50 mm dia for smooth functioning of cupboard/door shutter complete all as specified and directed.

S & F compacted recessed handle of size 150 mm suitable for sliding door as specified and directed

M & L for 4.80 mm thick sheet glass ordinary quality and glazing fixed to aluminium frame exc 0.50 sqm in each pane complete all as specified and as directed.

S & F galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks, or galvanised wire staples including etc complete all as specified and directed.

S & F of ring fit PVC (SWR) pipe of 100 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall/floor/trenches, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipe half round eaves gutters with rounded edges of 150 mm dia.

S & F PVC funnel of size 150 mm x 150 mm x 250 mm long and connected to rain water pipe at down.

M & L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint.

Surface excavation n exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

M & L for 75 mm thick cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base.

M & L for 15 mm thick heavy duty designer parking tile, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.50 in depth for foundation and getting out in soft/loose soil.

M&L PCC 1:4:8 type D2 (using 40mm graded stone aggregates) as in foundation

M&L for PCC (1:2:4) type B2 using 40mm graded aggregate in surface channel of drain.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement,including forms,moulds,mitered/stooped ends.

Rendering 15mm thick in Cement Mortar 1:6 on Fair Faces of Brick Walls or on Concrete Surfaces plastered Surfaces Finished Even and Smooth without using Extra Cement complete all as specified and as directed

M&L for PCC (1:2:4) type B1 using20mm graded aggregate asin coping on drain.

Returning filling, in including spreading, levelling, watering and well ramming in layers not exc 25 cm

Removing, excavatged material n.exc 50 m and deposited where directed at a level n.exc 1.5m from the starting point.

M & L for providing precast reinforced cement concrete 1:2:4, type B1 (using 20- mm graded stone aggregate) as in cover slabs & similar articals and set in CM 1:4.

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, including 20 mm dia concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild galvanised sunken box/metal flush box made out of 1.6 mm thick galvanised sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including accessories including cutting chases and making good the disturbed surfaces as per existing for one light point controlled by one switch complete all as specified and directed by Engr-in-charge.

Description all as per Srl item No. 60 here in before but for socket outlet point 5 Amp on same board.

Description all as per Srl item No. 60 here in before but with 2.5 Sqmm cable for socket outlet point 5 Amp on Independent board.

Description all as per serial item No 60 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified.

Supply and fixing modular switch 1 way 6 A module 230/250 volt , AC supply, ISI Marked, with cover plate complete all as specified and directed.

Supply and fixing modular sockets 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate complete all as specified and directed.

Supply and fixing modular sockets 6A/16A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate complete all as specified and directed.

Supply and fixing modular switch 16A 1 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, c with cover plate omplete all as specified and directed.

S & F Modular cover plate with frame & flush box of 6 modules, complete all as specified and as directed.

S & F Modular cover plate with frame & flush box of 4 modules, complete all as specified and as directed.

S & F Modular cover plate with frame& flush box of 3 modules, complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified.

Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED lights fitting 1x 12W, 220V,AC round recess warm/white type with driver, including connecting up with flexible copper conductor cable all as specified and directed by Engr-in-Charge.

Supply and fix exhaust fan, plastic body AC single Phase. 230V of size 250m sweep with, blades, and frame and louvers complete all as specified and as directed.

Supply and fixing LED security Building light LED 25 Watt , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete all as specified and as directed.

Supply and fix Flexible LED strips warm white/different colour option, 6.5W/mtr, IP 65 ingress protection, length can be customisable by using the cut and join provision, No of LED: 120 LED/meter, Energy Saving & LM80 Tested LED, High Voltage & Surge Protection, protecting the device from fluctuations for long lasting, performance with the Driver , connectors and all its accessories for fixing and full function of light complete all as specified and direcetd by Engr-in-Charge

Supply and fix in repair MCB Distribution board SPN 8 way, 240 volts, double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed.

Supply and fix in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed.

Supply and fix MCB DP 6-32A, 10kA, C curve complete all as specified and directed including taking down old one complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs MCB, single pole 6 to 32 Amps, 240 V, 10kA capacity fixed complete all as specified and as directed by Engr-in-Charge.

M & L Sub main wiring with two run single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 25 mm dia concealed on wall/ceiling in ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed. NOTE: Two runs of 6 sqmm and one run of 6 sqmm cable and one run of PVC conduit and cutting chases & making good shall be measured as one RM.

Material and labour for earthing in replacement complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I.all as specified and directed by Engr-in-Charge.

Supply and fixing of Steel tubular swaged poles with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-22 (9.0 metres long) including outdoor type pole junction box and its fixing accesories complete all as specified and directed by Engr-in charge.

Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp all as specified and as directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for laying of cable/erection of pole and getting out in soft/loose all complete as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm in hard/dense soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles , including necessary form work finishing even and smooth without using extra cement , all as specified and directed.

Supply and fixing/laying 40mm bore, steel tubings, galvanised, light grade with all fitting laid across road , in trenches or across PCC drain or along electric pole or floor/wall etc for protection of cable complete all as specified and as directed.

Supply & laying Sand coarse dry as in cushioning of underground electric cable in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable ) and gently punned down to 18cm thickness all complete as specified and as directed. Note :- Only punned down sand shall be measured.

M&L for fly ash bricks locally available laid dry width wise across the line of cable in trenches for protection of UG cable complete.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sq mm 4 core Iincluding laying in trench or fixed on wall through clamps complete all as specified and as directed by Engr-in-Charge.

shivam constructions (BID ID -3495951)

Ms Amrik Singh Bahra (BID ID -3496917)