PROVISION OF 02 X STORE SHELTERS / SHED, FOUR OVERHEAD PROTECTION SHELTERS FOR CANDIDATES OF SCN AND OTHER MINOR

Amount

Surface excavation in soft/ loose soil n. exc. 30cm deep and averaging 15cm deep and getting out all as specified and directed.

Excavation in trenches in soft/ loose soil n. exc. 1.5 m wide and n. exc. 1.5m in depth for foundations etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc. 10 sqm on plan and getting out complete all as specified and directed.

M & L for plain cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar (1:6) complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers n.exc. 25 cm thick each layer complete all as specified and directed.

Removing excavated material (soils) to a distance n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Material and labour rendering 15mm thick cement plaster on brick or concrete surfaces in cement mortar (1:4) mixed with integral water proofing compound in the proportion recommended by manufacturer, surfaces finished fair and even complete all as specified and directed. (WPC shall be measured and paid separately).

Material and labour for preparation of newly plastered or un-plastered surface of walls including cornices, plasters etc. and applying two coats of cement base paint over a coat of primer coat complete all as specified and directed.

Material and labour for rendering 15mm thick cement mortar (1:6) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of new plastered or un-plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Material and labour for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

Material and labour for (nominal mix) reinforced cement concrete (1:2:4) type B-1 using 20mm crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work n. exc. 200mm thick (Horizontal or sloping) for flat & rough finished surfaces of concrete complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C-2 using 20mm graded stone aggregate as in base course, plinth protection, laid in panels including finishing the concrete surface even & smooth without using extra cement complete all as specified & directed.

M&L 75mm PVC (SWR) floor trap plain with grating including jointing with solvent cement fixed in repairs complete all as specified and directed.

S&F galvanized iron tubes 15mm bore, medium grade with & including all fittings fixed to wall, ceilings and or laid in floors etc complete all as specified and directed.

S&F galvanized iron tubes 20mm bore, medium grade with & including all fittings fixed to wall, ceilings and or laid in floors etc complete all as specified and directed.

Supply and fixing bib taps, brass, fancy type, long body, chromium plated for 15mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

Supply and fixing rotational moulded polye-thylene water storage tanks, 500 litre capacity (cylindrical vertical with closed top), ISI marked, hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

Supply and fixing solid PVC wall lining consisting of 5mm thick wood grain PVC sheet, solvent cement and 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as and fixing at site on PVC frame complete all as specified and directed

S&F mild steel framed work for such as guard bars/ grills, grating etc with end of bars shouldered and/ or riveted forged into spikes, framed guard bars barred iron door, railings and similar work complete conforming to Fe-290 Gde E 165 including one shop coat of zinc chromate primer complete all as specified & directed.

M&L for cutting holes in brick walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required, depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick but not exc. one brick complete all as specified and directed.

M&L preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc. 0.5 cum in soft/ loose soil, getting out, returning, filling in, watering and ramming earth or broken rubble mixed with earth around in layers n. exc. 25cm and removing surplus soil to a distance n. exc. 50m and making good the surfaces complete all as specified and directed.

M&L cement concrete (1:2:4) type B-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete as in post holes complete all as specified and directed.

S&F rolled mild steel work roof trussed (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, Tee, Angle, Channel or Flat Sections) including distance pieces, cleats etc, Fe-410-W (Gde E-250) complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L hard core of broken stone or boulder of gauge n. exc. 63mm, deposited, spread and levelled in layers n.exc. 15cm thick, watered and well rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick Cement concrete, (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of flooring concrete complete all as specified.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L 80mm thick machine pressed precast concrete inter-locking paver blocks any shape and size conforming to IS 15658-2006, M-40 grade, with grey cement and pigment, laid in floor/ path/ hardstandings in any pattern as approved, laid over sand cushion and interstices filled with sand using plate vibrator complete all as specified and directed. Note: Sand for sand cushioning shall be measured and paid for separately.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregates) as in roof kerbs or mud stops, benching, coping etc, rounded or chamfered on edges complete including necessary form work all as specified and directed.

M&L PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation filling, mass concrete etc complete all as specified and directed.

M&L for 100 mm thick Cement concrete, (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of flooring concrete complete all as specified.

M&L for 20mm dia Ball Valves high Pressure of PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for Iron pipecomplete all as specified and directed.

S&F 20mm gun metal globe or gate valve, with iron wheel head screwed both ends for iron pipe and fixed complete all as specifed

S&F vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest (excluding flushing cistern and flush pipe) fixed including 'P' trap and provision of lime concrete bedding etc complete all as specified and directed by Engr-in-Charge.

S&F vitreous china wash hand basin, white, flat back 550 x 400mm excluding taps, waste chain and plug and porcelain stopper but including bracket and cutting for and pinning in ends of brackets complete all as specified and directed.

Supply and fixing 10 liters capacity PVC valves less symphonic action type, flushing cistern, low level, white with inlet ball valve, PVC flush pipe, float and handle including brackets complete all as specified

S&F pillar tap, cast copper alloy chromium plated, with capstan heads, 15mm bore dia of pipe screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F Brass chromium plated tubular towel rail 20 mm dia, D type, 600 mm long between flanges complete all as specified.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7 mm thick as in vertical surfaces i.e. skirting/dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including rendering 10 mm thick in cement mortar 1:4 finished rough to fix tiles complete all as specified and directed.

S&F 125mm size chromium plated brass shower rose with or without swivel joints including fixing to steel pipe or union complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

S&F mild steel CP grating 150mm dia with centre hole all as specified and directed.

S&F PVC solid door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified.

S&F Factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site, complete all as specified , shown on drawing and as directed .

S&F butt hinges extruded aluminium alloy 100 mm size with mild steel hinge plate and fixed complete all as specified.

S&F 150mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised, D-type, 150mm size, all as specified and directed.

S&F PVC (SWR) junction single (Single T) 75mm bore complete all as specified

Material and labour PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling, mass concrete etc complete all as specified and directed.

Material and labour 150mm bore reinforced concrete pipe, class NP2, laid and jointed with collars complete all as specified and directed.

Material and labour brick work with sub class 'B' bricks, old size, straight or curved on plan to exc 6m mean radius in half brick thick walls, built in cement mortar (1:4) complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed

Surface dressing not exceeding 15cm deep in soft/ loose soilincluding removing of rubbish and leveling to true surface for laying of concrete complete all as specified and directed.

Excavation soft/loose soil in over areas, n exc 1.5 m deep and getting out complete all as specified and directed.

M&L reinforced cement concrete (nominal mix) in (1:2:4) type B-1 (using 20mm graded aggregate) as in columns, pillars, posts and struts etc complete all as specified.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter, for rough finished concrete surfaces complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, for flat & rough finished surfaces of concrete complete all as specified

M&L mild steel TMT bars 8mm dia and over, cut to length bent to shape required including bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No.64.00 but 5mm dia and over 8mm dia upto and including 10 mm dia in stirrups spacers and binders

S&F rolled mild steel joist, channel, angle or tee sections fixed independently, without connecting plates, ( cut to ordinary lenghts i.e. within 20 mm of the length ) etc confirming to Gde Fe-410-W (Gde -E-250) quality 'A' complete all as specified

S&F rolled mild steel sections conforming to Fe-410-W (Gde E-250) as in main posts and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats and other connecting plates etc complete all as specified and directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Fe-410-W Gde-E-250 quality 'B' complete all as specified and directed

S&F purpose made mild steel screw bolts diameter of neck 12 to 20mm with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt n. exc. 30cm long complete all as specified and directed.

M&L 18-20mm thick machine cut Kota stone slabs as in flooring, jointed with grey cement mixed with pigment to match the shade of the slab including grinding, rubbing and polishing to mirror finish with & including screed bed or bedding layer of mortar 15mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and directed

M&L for 18 to 20mm thick machine cut Kota stone as in vertical surfaces, risers of steps, skirting, dado and pillars etc laid over and including 10mm thick rendering in cement mortar (1:4) jointed with grey cement slurry mixed with pigment to match the colour of stone slab including rubbing and mirror polishing complete all as specified and directed.

Removal of surplus soil to a distance exc. 1.50 KM and depositing where directed at a level n. exc. 5 KM above the starting point complete all as specified and directed.

M&L 35mm thick 2nd class hard wood factory made plain framed, panelled shutters (two panels), with lock rail and panels of 9mm thick BWP commercial ply or of veneered particle board 12mm thick with commercial veneering on both faces with rails and style. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L preparation of new wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in filling in hollow pressed steel door frame complete all as specified and directed.

M&L mild steel work as in holdfasts, knee piece and similar small article complete all as specified and directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

m&l RCC 1:2:4 using 20mm graded stone aggregate as soundation, including rafts. Footing, foundation beams, plinth beams, base for columns etc basement slabs under-reamed piles and mass concrete complete all as specified and directed

M&L reinforced cement concrete nominal mix in (1:2:4) type B-1 (using 20mm graded aggregate) as in beam lintel band etc complete all as specified.

Supply and fixing Pre painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x 60mm comple all as specified and directed

Spreading, leveling, watering and well ramming in layers n.exc. 25 cm thick each layer complete all as specified and directed.

Material and labour for plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs benching etc, water throughs and the like including weathring, slightly rounded or chamfered angles and throating, as directed including necessary form work complete all as specified and directed

S&F 75 mm bore PVC(SWR) pipe of pressure rating 4kgf/cm2 single socketed in any length with rubber ring joints jointing with adhesive to wall/laid in trenches complete all as specified and directed

S&F 110 mm bore PVC(SWR) pipe of pressure rating 6kgf/cm2 single socketed in any length with rubber ring joints jointing with adhesive to wall/laid in trenches complete all as specified and directed

S&F 15mm dia fancy type chromium plated with long shank and cup concealed stop cock complete all as specified and directed

S&F 15mm stop valves/angle cock, chromium plated, screwed down, high pressure with cruth or butter fly handle screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed

PVC connection fiber, reinforced 45cm long with brass check nut and PVC washers at both ends complete all as specified and directed

M&L for 40mm thick damp proof course in cement concrete 1:2:4 type B-0 in horizontal/vertical surfaces including necessary formwork and applying evenly a coat of blown type bitumen @ 1.5kg/Sqm and inlcuding with clean dry sand @ 0.05 cum / Sqm

KAMALJIT SINGH CONTRACTOR

M/S Vinod Kumar

PAUL CONSTRUCTION CO.

SARASWATI CONSTRUCTION CO