Beautification and Illumination Surrounding at Shree Mahadev Temple Mollem in Dharbandora Taluka Goa

Amount

CIVIL WORKS

Earthwork in excavation over areas by mechanical/mannual means at all depths in all type of strata comprising any of the materials such as soil, silt, sand, clay, gravels, moorum of all varieties, shingles, pebbles, all types of conglomerates, all types of laterite rock, soft rock, disintegrated rock, fissured/ shattered/ decomposed rock or weathered rock and all such other materials as described under appendix to these specifications whether in full or in parts as the case may be adopting any approved method or methods as may be convenient or permitted inclusive of chiselling, wedging etc. in all conditions such as dry, moist, saturated, submerged, foul conditions etc. including dressing of sides and ramming of bottoms, including getting out the excavated soil at all lifts, including pumping or bailing out water as directed by the Engineer on site including segregating the excavated earth along with crushed rock pieces of size 75mm and below and disposal of surplus excavated earth as directed by Engineer within a lead of 50mt and all lift and including breaking of excavated rock into boulders of size ranging from 150mm to 300 mm and stacking the broken boulders at a place specified by the Engineer on site etc. complete

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Disposal of unserviceable material such as buiding rubbish,wood,earth excavated rock etc for all leads and lifts beyond 50m, Upto 5km

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement. Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: a)All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) a) All works upto plinth level

b) In walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and structs etc. upto floor five level

c) In beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases upto floor five level

Centering & shuttering including Strutting, Propping & removal of forms for : i) Foundations, Footings, Bases for columns

iii) Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan)

v) Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams exceeding 1m in depth

xiii) Suspended floors, roofs landings, shelves & their supports

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon. b) Second class Indian teak wood

Providing and fixing 35 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including anodized aluminium butt hinges with necessary. b) Second class Indian teak wood

Providing flat iron hold fast 40 cm including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embeded in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 stone aggregate 20 mm nominal size. a) 40 x 3 mm flat iron hold fast 40 cm long

Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws. b) Ornamental grill

Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete c) 150 x 10 mm

Providing & fixing bright finished Stainless Steel Aldrops with screws etc. complete. 250 x 150mm

Providing and fixing bright finished brass handles with necessary screws etc complete a) 125 mm

Providing and fixing bright finished brass door latch with necessary screws etc complete a) 300x 16 x 5 mm

Providing and fixing 150 mm. bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete.

Standard Wood Core Door Shutter with Single Colour Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood, moisture less than 17%, wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps).The core of Shutter will be filled with MR2nd grade Block Board. The shutter to be water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. b) Shutter Thickness : b) 35mm

FRP (Fiber Reinforced Polymer) Frames Manufacture, Supply and Installation (with anchor fastener) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) Frame of cross section as per options below with right angle joint and FRP (Fiber Reinforced Polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). The core of frame would be filled with seasoned wood as infill material. The slot of frame for door resting will be of suitable width so as to take specified thickness door.. The frame will be water proof as well as mild acid/ alkali resistant manufactured in an ISO 9001- 2015 certified company. a) Specified Cross Section: a) 3” x 2”

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint. b) In tees, angles, flats and channels

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of (SAIL, TATA. VIZAG, JSW ,APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-incharge: windows with two sliding shutters using 18 mm series shutters section.Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section c) Figured glass

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-incharge: Adjustable louvered windows. Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section c) Figured glass

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) a) 20 mm thick.

Providing and fixing vitrified matt finished (600x600) and 10mm thick tiles in floor, treads of steps, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Providing and fixing vitrified antiskid tiles (320x320) and 10mm thick tiles in floor, treads of steps, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete. b) 600 x 600 mm - light Shades

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria) conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. b) Wall Ceramic Glazed Tiles : 300 x 450

Providing & laying of minimun 80mm thick factory made Shot blasted cement concrete Interlocking paver blocks of minimum M40 and above grade made by heavy duty block making machine with strong vibratory compaction and of approved size and design/ shape laid in 50mm thick compacted bed of coarse sand, filling the joints with coarse sand etc. all completed as per the direction of Engineer-incharge. The product should comply with IS 15658: 2006 and manufactured by ISO 9001: 2008 certified plant. a) Grey Colour

b) Other Colours

Removing Existing interlocked paver block, cleaning and Laying / refixing the same paver block with strong vibratory compaction machine and approved size and design/ shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.

Providing & Fixing in position Double Skin roof with Zincalume/ Galvalume colour coated & bare profile sheet with subtle square fluting factory cut at all heights for roof, side & Gable cladding complete in all respect. TOP SHEET-The end rib shall be designed for anti-capillary action. The feed material should be manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc &1.5% Si) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with quality paint coat as per AS/NZS 2728 type 3-4. The paint shall have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior SMP coat on top surface and nominal 5 μm reverse backer coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade. Total Coated Thickness (TCT) should be 0.50mm. Total Painted Thickness (TPT) should be in addition to 0.50mm. The steel sheet shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturers recommendations. The profile sheet, fastener size etc. shall be approved by the Engineer.

The sheeting should be with minimum 200mm lap & waterproof with Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed Z-Sub Girt - roll formed section 50x50x50x1.50 TCT, 120GSM Galvanised, High Strength (345 MPa), approximate Wt. 1.85 kg/r.m. fixed with self tapping screws Glass Wool Insulation with FSK facing 50mm with 24 kg/m3 density in between 2 sheets. LINER SHEET-bare galvalume/zincalume roofing sheet of same profile as top sheet. The feed material is of manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.47 mm TCT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides), passivated & resin coated. The feed material should have coil manufacturer’s product details marked at regular interval for confirming genuinity of the material. complete as per the directions of the engineer. The steel manufacturer's test certificate for the chemical & mechanical properties of steel must be submitted for approval prior to installation.

Providing & fixing in position Galvalume/Zincalume flashings, cappings, ridges, gutters upto 600mm/610mm girth and min 3.00m in length (cold Rolled Steel 550 MPa yeild Stress ASTM A 446 Grade E) with hot-dip metallic coating of aluminium-zinc alloy(AZ 150 galvalume) (150 gms/sqm total of both sides with Al-Zn Composition= 55% & 43.5% resp. & 1.5% Si conforming to ASTM 792/ AS 1397) 0.45 mm base metal thickness and 0.50mm total coated thickness, factory cut at all heights for roof, side & gable cladding complete in all respects with AZ 150 GSM SMP color Coated (20mic exterior coat of Silicon Modified Polyester paint system over 5 mic primer and 5 mic polyester back coat over 5 mic primer) incl. fixing to purlins with no 12x14x55mm mechanically galvanised hex head self drilling screws of the best quality as per AS 3566 class 3-4 approved, which should be compatible to be used with sheets. with integral washers and EPDM seals etc. Silicon sealant nonhardening neutral cure type shall be applied at all end laps, complete as directed.

12mm cement plaster 1:4 (1 cement : 4 fine sand)

6mm cement plaster to ceiling 1: 4 (1 cement : 4 fine sand)

Neat Cement punning

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Removing white or colour wash by scrapping, sand papering and preparing surface smooth including necessary repairs to scratches etc. complete.

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Applying priming coat with ready mixed primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade.

Water based crosslinking all acrylic emulsion which offers superior protection and beauty to cement and concrete based floors. Ensure that the surface to be painted is free from any damp, loose paint, dust, wax orgrease and other contaminants. Remove all contaminants such as dirt, grease, oil, dust etc. with soap powder solution using a scrubbing brush. Dry for minimum of 4 - 6 hours before painting. Moisture content in the surface should be less than 10%.

Painting one or more coats with superior quality ready mixed paint of steel work of approved brand & manufacture in all shades on old work to give an even shade.

Providing and applying white cement based putty of average thickness 1.00 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade. .

Wall painting (one or more coats) with plastic emulsion paint of approved brand and manufacture on old work to give an even shade.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Painting one or more coats of acryllic exterior paint of approved brand and manufacture(Such as Dulex/ Asian Paints/ Sherwin Willians) on old work including cleaning the surface with water etc. complete.

Proving and fixing white vitreous china water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10 litres high level P.V.C. flushing cister (of approved make) with fittings, rack bolts 32 mm diameter P.V.C telescopic flush pipe with fit tings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon pull complete cutting and making good the walls and floors where required. a) Long pan pattern W. C. Pan

Proving and fixing white vitreous china water closet squating (European type w.c. pan) with seat and lid, C.P. brass hinges and rubber buffers 10 lts. High level P.V.C.. flushing cistern (of approved make ) with fittings, rack bolts 32 mm diameter P.V.C. telescopic flush pipe with fit tings and clamps 25mm P.V.C.. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon. chain and pull complete, cutting and making good the walls ad floors where required a) W.C. pan with white plastic seat and lid.

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, including cutting and making good the walls where required. b) Flat back wash basin size 630x 450mm with a single 15 mm C.P. brass pillar taps.

Providing and fixing toilet paper holder : a) C.P. brass

Providing & fixing liquid soap container with C. P. brass lid and brackets fixed to wooden cleats with C. P. brass screws b) Plastic container

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality : a) Low pressure with copper. floats : 3) 25mm nominal bore

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996. c) 1000 lit. capacity

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand ;4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse sand :4 graded stone agrregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cemetn and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design. d) Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg)

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed: a) 110 mm dia

b) 75 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. a) 110 mm dia

b) 75 mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : a) 100 mm dia

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : a) 110 mm dia

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door : a) 110mmdia

Providing and fixing U.P.V.C. pipe clips (approved make ) for S.W.R. pipes : a) 110 mm dia

b)75 mm dia

Providing and fixing R.P.V.C. vent cowl: a) 110 mm dia

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete. a) Overall size 610mmx510mm (24"x20") bowl size 545mm x 445mm x 200mm (211/2"x 17 1/2"x 8") depth 200 mm. Glossy. 1.0mm thk

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards

Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way Bib Cock with single knob and wall flange conforming to IS 8931:1993 15mm nominal bore.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work I) SCH-40(blue)/(white) a ) 20 mm dia nominal outer dia pipes.

b) 25mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work. I ) SCH-40(blue)/(white) a) 20mm outer dia.

b)25 mm outer dia.

Providing and fixing Angular Stop Cock with wall Flangue - Jaquar make (a) Florentine (FLR-5053N), (b) 15 mm nominal bore.

Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931;1993 a) 15mm nominal bore

Providing and fixing white vitreous china flat back Large lipped front urinal basin of 590x375x390mm size with Urinal Valve Auto closing system with built in control cock & wall flange with fittings, spreader, R.S. or C.I. brackets, standard size C.P. Brassl flush pipe and spreaders with C. P. brass unions & C. P. Brass clamps with waste fitting as per IS 2556, PVC trap with outlet grating and other couplings in CP Brass complete, including painting, fittings, cutting and making good the walls and floors where required. - Range of one urinal basin

Providing and fixing Straight grab bar S.S. 304, Straight SHAPED DISABLED GRAB BAR of IZE-300MM (L) and 32MM DIA. and thickness1.5 mm of the approved brand and make

ELECTRICAL WORKS

Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator). h) 4 way (8+12), double door, Horizontal type Cat A

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/RCCB/Isolator) (b) 8 way single door Cat A

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (e) TPN, Cat A

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/RCCB/Isolator). (f) (f) 8 way double door Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. a) SP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. c) DP, Cat A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent surface PVC conduit ( medium)of appropriate size as required (b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent surface PVC conduit ( medium)of appropriate size as required (c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface PVC conduit( medium) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (a) Group A -- with Cat A Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface PVC conduit( medium) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required. (a) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required. (a) Cat A

Supplying & erecting LED 20W tube light fitting (4 feet), 5700K, with CRCA housing, heat sink, with industrial grade heavy duty driver complete Havels Cat stout mini 1200bs 40w led 865 Make Philips / Wipro cat no LL24-541-XXX-57-CD (including lamp)

Supply, Installation, Testing and Commisioning of 6w LED Corrosion proof Surface/Recessed mounted square / circular 6 W downlighter having pressure die-cast aluminium housing with white front frame with opal translucent cover with provision for spring loaded mounting clips complete with Electronic driver, LED Downlight 6W 90-260V AC 50HZ LUMINOUS FLUX-550-650 Lm . makeCrompton, Havells,wipro,reyteck, Leska as directed by Engineer Incharge complete as required.

Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. (b) Cat B

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required (a) Cat A

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supply and erecting of 9 inch (225 mm sweep) exhaust fan with double ball bearings, 1400 rpm, complete with all accessories.(a) Cat A

Supply and erecting of 18 inch (450 mm sweep) exhaust fan with double ball bearings, 1400 rpm, heavy duty, complete with all accessories.(a) Cat A

Supply, installation, testing and commissioning of electronic type three phase energy meter (KWh), 4 wire, ISI marked, in polycarbonate or sgheet steel body ( base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only.(a) 5 to 20 A

Supply and erecting meter box suitable for three phase energy meter and incoming SP/DP MCB, fabricated out of 16 SWG sheet steel, powder coated, complete as required and conforming to the requirements of Goa Electricity Department

Supply, Installation, Testing and Commissioning of Architectural Pole of 6mtr Height Double arm made of galvanised iron sections of 140mm & 76mm dia. •This architecturally designed pole is structurally sound. Wind speed considered in design 50m/s, IS 875: PART - 3 :1987 •Material for tubes steel of grade YST 210.• Material for base plate steel of grade E250 to IS 2062 ; 2011. The Bracket will be provided with reducer/expander for holding the suspended type fixture on to the main pole with all arrangements having position perpendicular to the ground. The bracket shall be single/double arm on 6mtr with a span of 1000mm. The bracket top shall be covered with FRP cap to enclose the pipe. The Pole will be placed with a Aluminium embellishments on the bottom & Middle section for aesthetic & Decorative purpose. The pole will be provided with an inbuilt junction box to fix 32Amp Connectors & 6Amp MCB inside the cut window of the bottom pipe the in built box should have a flush door of suitable size. The Decorative pole will be mounted on a square base plate of size 250 X 250mm having 12mm thickness. The mounting steel plate along with hot dip galvanised foundation bolts of size M16 X 600mm to be used for ensuring firm grouting in the specially designed RCC foundation. The Galvanised pole should be painted in 3 layer coating (Coating thickness should be more than 50 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy zinc primer & 3rd final layer with PU Paint of Matt Black on Pole and Golden on Aluminium Embellishment or as per choice. Make: Suncity, La Lumirie, Reyteck, Havells, Dwarka Casting as required as directed by the engineer in-charge.

Supply, Installation, Testing and Commissioning of 60W decorative luminaire made of spun aluminium body with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s is comprised of a deep drawn chemically polished and co-extruded, thermoformed polycarbonate protector stabilized agent UV rays suitable for 60W LED. Fitting should be suspended mounting type fixture. System Wattage:60W LED, Protection class:IP65, Driver Integral: Constant Current, Input Voltage: 230-240 Vac, Frequency: 50-60Hz, Operating Voltage:1200- 277Vac, Operating Temperature: 0deg to +50deg C, single phase ac supply.● light Source : Bridegelux, LED Lumens: @120lm/w 7200lm, CRI(Ra):>80, LED Colour Temperature: 3000K, Life Span:>59,000 Hours,, ● Physical Body: Die cast Aluminium Base, Body Spun Aluminium, Diffuser: Convex Type Translucent / V Translucent Polycarbonate glass, Mounting: Suitable for 48mm OD Pipe, Finish: Powder Coated Black, ●Driver Power Factor:>0.95, THD:87%. Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KVA and external surge protection device of 10KVA. LED's of Bridgelux & driver to be of make Philips/Fulham. IP65 and LM79-2019 report to be provided. Make: Suncity, La Lumirie, Reyteck, Havells, Dwarka Casting as required as directed by the engineer in-charge.

Supply, fixing, testing and commissioning of 50 W LED flood light luminiare IP 66 optic compartment, pressure die cast aluminium housing, control gear compartment, frame with toughened glass with luminious efficacy >115 lumen/W at ta 25 deg c.in built surge protection upto 10kV as required and directed by engineer incharge. make Crompton, Havells,wipro,reyteck, Leska .

SITC of IP: 66/IP:67 PVC Junction Box having the Facility to house 4 way Bakellite strip for connection to the spike light.(Make:- Hensel)

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. (2) 3 Core 2.5 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. (2) 3 1/2 Core 35 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. (5) 4 Core 16 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (1) 3 1/2 x 35 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (5) 4 x 16 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 1) 3 x 1.5/2.5 Sq. mm.

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid seperately). (b) In rocky strata

Supplying and laying 25 mm x 5 mm GI strip in 40 mm dia GI pipe from earth electrode as required

Providing and laying earth connection from earth lectrode with 6 SWG dia GI wire in 15 mm dia GI pipe from earth electrode as required

SAIBINI CONSTRUCTION (BID ID -46513)