SPECIAL REPAIR TO BATHROOM TOILETS PC34 PC35 AND 01 TA BN BLOCK AT AIR FORCE STATION CARNICOBAR PROVN OF STORAGE ROOM FOR LPG CYLINDER NEAR AIRMEN MESS AT AF STN CARNICOBAR PROVISION OF EMERGENCY ALARM SYSTEM AT AIR FORCE STATION CARNICOBAR A

Amount

Material and Labour for non-skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set and jointed in cement mortar and pointed in white of coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. NOTE: No extra cost shall be allowed for removing and re-fixing and necessary cutting of door etc if any required during execution of work.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise specifically provided for complete all as specified and as directed.

M&L for MS work as in Wind Tie in roof and MS structural works in trusses, etc with screwed ends including nuts, washers and mild steel plates for walls chimneys, roofs arches etc any kind rods and straining bolts conforming to Fe-290 Gde-165 complete all as specified .

Supply and fix rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats conforming to Fe-410W(Gde E-250) quality A complete all as specified and as directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (without taking off shutters from the frame) complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50 mm x47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube, supporting & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plian colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement supplying and fixing in the frame at site as per specification & drawing of SSR Part II.

Supply and fix 125mm long mild steel cold rolled medium weight butt hinges fixed with screws to wooden/PVC frames or with welding to steel frames including all accessoriescomplete all as specified and as directed.

Supply and fixing aluminium alloy,anodised, sliding door bolt of length 250mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded section or cast-aluminium alloy complete all specified and as directed.

Supply and Fix 150mm long aluminium anodised barrel tower bolt all as specified and as directed by Eng-in-charge.

Supply and fix extruded aluminium alloy handles, fabricated type, anodised 150mm size complete all as specified and as directed

M&L for preparation of new or previously untreated steel surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and as directed

Material and labour for preparation of old decorated steel & iron surfaces of any description exceeding 10 cm width or grith not otherwise specified and applying one coat of syntheic enamel paint all as specified and as directed.

Taking up or down steel tubing /CPVC pipe 15 mm bore including connections, cleaning for refixing or removal to store all as directed.

Taking up or down steel tubing 20 mm bore including connections, cleaning for refixing or removal to store all as directed.

Supply and fixing galvanised steel water tubing medium grade 15 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc, fixed to wall/floor/ceiling including necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed.

Supply and fixing galvanised steel water tubing medium grade 20 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc, fixed to wall/floor/ceiling including necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed.

Supply and fixing in repairs Vitrious China squatting pan ' Orissa' pattern of size 580 mm x 440 mm white with integral foot rest excluding flushing cistern and flush pipe including P or S trap making good the floor to match with existing floor complete all as specified and as directed.

Supply and Fix in repairs vitreous china wash down water closet Pedastal pattern white (excluding flushing cistren ) including trap set, seat cover and fixing of flushing cistern, brackets, flushing pipe etc, etc. with 'P' or 'S' trap, making good the floor to match with existing floor complete all as specified and as directed.

Supply and fix in repair 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern low level, white, with inlet ball valve, float and handle including brackets, flushing pipe, 450mm long PVC Connection and connection to trap, and to flushing and making good to floor complete all as specified .

Supply and fixing in repairs flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed.

Supply and fix in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Supply and fix in repairs 2 way angle valves/2 in 1 angle cock, 15mm bore,quarter turn with wall flange, chromium plated, screwed down, high pressure with crutch or butterfly handle and fixed complete all as specified and directed.

Supply and fix stop valves/angle cock, 15mm bore, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixing Vitreous China full stall urinal bowl type (back or corner wall type), white , of size 465mm x 355mm x 265mm complete with chromium plated waste fittings including providing and fixing plugs,bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing arround urinal back in cement, (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed.

Supply and fixing in repairs PVC waste pipe 32mm dia with 40mm dia reducer, 90cm long for WHB/urinal outlet with 4 Nos screws for fixing pipes, complete all as specified and directed.

Supply and fixing in repairs vitreous China wash hand basin, white (flat back or angle back type or counter top) of size 630X450mm including 32mm brass chromium plated waste fitting, a pair of cast iron bracket duly painted including cutting and pinning in ends making good disturbed surfaces in CM 1:3 excluding pillar tap but chain , plug and porcelain stopper, brackets etc all as specified and as directed.

Supply and fix in repair 15mm dia pillar tap, cast copper alloy, chromium plated, fancy type, with capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw for iron pipe Make: CERA /Parryware/Hindware

Supply and fixing in repair 6 mm thick bevelled edge looking mirror of size 600 x 450 mm mounted on 6 mm thick AC Building board or commercial plywood/hard board backing and fixed to wooden plugs with CP Screws and cup washers all as specified and as directed.

Supply and fix Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

Supply and fix waste coupling of PTMT 32 mm size (half or full threaded) suitable for urinals/ WHB/Sink etc (Minimum weight 32 mm - 45 gms) all as specified and as directed.

Supply and fix in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

Supply and fix in repairs 15mm dia bib taps cast copper alloy fancy type chromium plated with crutch or butterfly handle screwed down , screwed for iron pipe or union complete all as specified and directed.

Taking down unservicable shower rose and supply and fix brass chromium plated shower rose 125mm size with swivel joints including fixing to steel pipe or union complete all as specified and as directed.

Supply and fixing in repairs Towel rails tubular brass chromium plated 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

Supply and fix soap dish vitireous china white 160x160x90mm (Approximate) complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia. single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm dia. single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed.

S&F PVC (SWR) junction single 75 mm bore, (single T) equal or unequal with access door complete all as specified and as directed.

Supply and fix in repairs stainless steel grating 110 mm dia with waste pipe hole complete all as specified and as directed.

Supply and fix in repairs stainless steel grating 110 mm dia without waste pipe hole complete all as specified and as directed.

Demolition and breaking up 110mm bore drain pipes (RCC pipe/Salt glazed ware or Reinforced concrete) set in cement mortar including haunching and removing debris to a distance exc 1.5Km and n.exc 5Km all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm dia. single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) junction single 110 mm bore, (single T) equal or unequal with access door complete all as specified and as directed.

S&F PVC (SWR) bend 110 mm dia with access door complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for Pre-cast cement concrete block masonry with solid blocks using type C1(1:3:6) (20mm graded aggregate) ,size exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Material and labour for providing reinforced cement concrete 1:2:4 type B1 nominal mix using 20mm graded stone aggregate as in as in beams, cantilever, lintels over 1.5M span etc complete all as specified and directed.

Material and Labour for plain cement concrete 1:2:4 type B1 using 20mm graded granite stone aggrgate as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including use of necessary form work all as specified and as directed.

Supply and fix 125mm long mild steel cold rolled medium weight butt hinges fixed with screws to wooden/PVC frames or with welding to steel frames including all accessoriescomplete all as specified and as directed.

Material and Labour for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ,for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L mild steel TMT bars 5mm dia and over up to 10mm for stirrups cut to length , bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia bars confirming to Fe-410-S or Fe-410-0 complete in all respect as specified and directed.

Material and labour for 15 mm thick rendering on brick/concrete wall surfaces in two layers in CM 1:4, finishing coat of 5mm thick, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of of new plastered/concrete surfaces of walls and applying two coats of acrylic distemper of approved shade/tint over a coat of primer, over surface of wall all as specified and as directed.

Material and labour for 100mm thick plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floors including necessary form work all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 meter in depth for laying UG cable, GI pipe or filling resistance enhance compound and getting out, excavated earth, forming bottom surfaces to required level complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material (soil) n.exc 50 m and depositing where as directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

Material and labour for cutting bituminous road/path/ harstanding(hard Rock ) of any description not more than 50CM x 45 CM size for laying of pipe or cable (crossing the cables across the road) and making good with 30cm thick hard core with broken stone or boulders of gauge not exceeding 63 mm, deposited, spread, and levelled in layers not exceeding 10 cm thick watered and rammed to a true surface and 15cm thick PCC 1:2:4 type B-2 using 40mm graded stone aggregate as top layer, removing the surplus material away from the site, all as specified and directed by the Engr-in-charge

Supply & Fix 40 mm dia galvanized iron tube medium grade for cable protection, supporting to poles, plinth protections, road crossing, trenches, footpath etc including clamps, nut, bolt and washers etc after taking out unserviceable pipe complete all as specified and directed.

Material and labour for Sub main wiring using two runs of single core PVC insulated cable (FR) 4 sqmm copper conductor multi stranded and one run of 4 sqmm copper conductor insulated cable (FR)using as earth wire drawn through and including suitable size steel conduit, complete all as specified and directed. Note- 3 run of 4 sq mm PVC copper wire and One run of PVC conduit shall be measured and paid as one unit.

Supply & Fix flexible copper cable PVC insulated multi stranded Weather proof flat twin core cable of 6 sqmm, 230 volt complete for connecting audio alarm hooter complete all as specified and as directed.

Supply and fix Stove enamelled, blank, Rigid steel conduit, welded of 25 mm dia including all fitting such as bends, elbow, coupler lock nut etc, complete all as specified and directed by Engineer-in-Charge.

Supply and fix High density polyethelene (HDPE) pipe of pressure rating 6kg/sq.cm 40 mm dia laid in trenches/wall/floor with all accessories complete all as specified and as directed. Make: Supreme/Finolex/Prince. NOTE: Excavation and earth work shall be measured and paid separately under relevent items.

Cutting holes into or through cement concrete or brick work, reinforced or otherwise and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 of superficial area not exceeding 150 Square CM complete all as directed.

Supply and fixing of SPDT switch with PVC surface mounting 1 module Gang Box, AC 230 Volts, complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing of Audio Alarm Hooter 60 / 80 / 120 dB sound level adjustable with inbuilt volume control, Flush panel mounting / Wall mounting, Dust and Vermin proof enclosure, Audible distance : 80/100/120 meters testing all as specified and directed by the Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding but not backing) and rubbish of the premises all as specified.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid and bedded and pointed in any mortar all as specified and as directed.

Material and Labour for non-skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in cement mortar and pointed in white of coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. NOTE: No extra cost shall be allowed for removing and re-fixing and necessary cutting of door etc if any required during execution of work.

Material and Labour for glazed ceramic coloured tiles in vertical surface 450x300x7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles over and including 10mm thick backing coat in CM 1:4 cmplete all as specified.

Material and Labour for vitrified ceramic tiles 8-10 mm thick polished area of each tiles not exceeding 0.36 sqm of any shade and any pattern (pattern consists combination of two or more tiles ) as in floor etc jointed in neat cement slurry and pointed in colored cement to match colour tiles over and including 15mm thick screed bed in CM 1:6 and pointed in coloured cement to match coloured tiles complete complete all as specified and as directed. . Note:- (i) The colour, shade and pattern shall be approved by the GE during execution work. (ii) No extra cost shall be allowed for Removing and refixing and necesary cutting of door etc if any required during execution of work.

Material and Labour for 20-25mm thick machine cut kota stone as in floors etc, set and jointed in cement mortar and pointed in white or coloured cement to match over and including 20 mm thick screed bed in CM 1:4 complete all as specified and as directed.

Material and Labour for Granite 20mm thick ( of any type table rubbed and polished) work machine cut as in steps, jambs pillars,window cills, cooking platforms and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of granite and laid over and including 15mm thick cement mortar 1 :4 complete all as specified and directed.

Material and Labour for rounding to edges of Granite slabs one edge, such as in steps cooking plateform, and other similar situation complete all as specified and directed

Demolition of reinforced cement concrete of any description ad in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Demolition of brick work / stone boulder / PCC block masonary, built in cement mortar or cement lime mortar including all quoins, arches pillars, etc but excluding ashlar facing, dressed stone works, precast concrete articles and precast concrete block wallings complete all as specified and as directed.

Material and labour for providing reinforced cement concrete 1:2:4 type B1 nominal mix using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note : Reinforcement and form work shall be measured and paid separately.

Taking down cement plastering on concrete or Brick works surface racking out joints, hacking for key , scrubbing down with water, removing rubbish/debris etc complete all as specified and as directed.

Material and labour for rendering 15 mm on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed.

M & L Preparation of old distempered and painted surfaces including washing, rubbing down and stopping by brooming down , scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of Distemper oil emulsion on wall surfaces.

Supply and fix in repairs stainless steel grating 125 mm dia with waste pipe hole complete all as specified and as directed.

Supply and fix in repairs sinks without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers, and wastes, including bedding in cement mortar to dwarf wal or including fixing cantiliver brackets and connecting union ot pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Material and labour for hard core with broken stone or boulders of gauge not exceeding 63 mm, deposited, spread, and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface all as specified and as directed.

Material and labour for 40mm thick plain cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in as in leveling course including use of form work as necessary complete all as specified and as directed.

Material and labour for 75mm thick plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floors including necessary form work all as specified and as directed.

Material and labour for chequered cement concrete tiles 30cm x 30cm x 25mm with grey cement and pigment, hydraulically machine pressed, set, jointed and pointed in neat cement slurry to match colour of tiles, over and including 15mm thick screed in CM 1:6 in floors complete all as specified and as directed.

Material and labour for fixing 18 mm thick glossy surface Acrylic board both side with decorative choice lamination fixed with suitable screws for box type cabinets works including to fix glossy finishing Acrylic layer of 2 mm thick beading in same colour as board on the vertical surface of the cabinets and shutters after taking down the existing boards of any description, complete all as specified and directed.

Supply and fix self-closing stainless steel hinges with ISI mark, fixed with screws including all accessoriescomplete all as specified and as directed.

Supply and fix stainless steel handles, fabricated type, 100mm size complete all as specified and as directed

Supply and fix magnetic Ball catches for Acrylic board with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

Supply and fix aluminium powder coated frame for doors,windows, ventilators with one or more rebates with joint clip and using rubber beading etc complete all as specified and directed. Note : Glass panel/particle board panel filling shall be measured and paid separately.

Supply and fix powder coated aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, and sliding tower bolt 150mm long anodised aluminium snap beading, screws etc. complete all as specified and as directed.

Supply and fix for powder coated, Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

Supply and fix Aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with Aluminium alloy wire staples complete all as specified and directed

Supply and fix Powder Coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum coating of grade AC 15) of DG 102 design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved aluminium standard section around the opening, all complete as per requirement complete all as specified and directed.

Supply and Fixing 5.5mm thickordinary quality glass with film cover, ordinary quality and glazing with oil and putty in square not exc 0.5 sqm in each pane complete all as specified and as directed.

Material and Labour for pre-laminated particle board 12 mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws in timber frame work complete all as specified and directed.

Supply and fix door closer hydraulically regulated cast iron body, designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed complete all as specified and as directed.

Supply and fix in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium ally sheet foundation box, main body with stainless steel cover, govering pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed. Make: SANDHU, EVEREST

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Supply and fix anodised aluminium snap grid frame work for false ceiling with 605mm x 605mm size, consisting of main Tee of size 40 x 40 x 2mm, cross Tee of size 40 x 40 x 2mm and wall angle of size 40 x 40 x 2mm of approved make including all necessary cuttings, fixing of aluminium section firmly in position with and including steel hangers 6 mm dia G.I. wire (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 40 mm long in soffit of slab/walls complete all as specifed and as directed including provision of with 4mm thick Non Asbestos boards, ordinary type for fixing in 600 mm x 600mm grid, fixed in ceiling, flat or sloping, complete all as specified and directed. Note :- Rate quoted above shall be deemed to include for making holes, cutting chassis if any required and making good to existing walls in cement mortar 1: 3 to match with existing surface finish as directed at site.

Taking down carefully Ceiling/Exhaust/wall mounted Fan (any size), sealing cable end, dismantling blades and removing fan & blades including deposit to AGE E/M store yard, complete all as specified and directed by Engineer-in-Charge.

Supply and fix energy efficient BEE 6.00, 5 star rated high speed, copper wound Stealth air BLDC ceiling fan, air delivery 210 CFM, 1200mm sweep, direct voice controlled which functions without internet, Wi-Fi, smart phone or bluetooth, RF pebble remote control with all direction sensing, single phase 230 Volts, with motor-blade set, downrod, shackle, assembly kit, canopy and accessories, including making provision for anchor hooks for hanging etc and electric connection, five star rated with brushless direct current motor (BLDC), complete all as specified and directed. Make- Havells, Model no- FHCVC5SIBL48/ FHCVC5SMBK48/ FHCVC5SPWT48 or Equivalent in Bajaj, Crompton, Usha, and Orient as approved by GE

Supply and fix wall fan 400mm sweep single phase 230 volt, 380 RPM, wider blades for higher air delivery connecting with PVC insulated 23/.0076 flexible copper conductor BEE 5 star rated complete all as specified and as directed. Make- Havells, Model- Swing off-white, code-FHWSW4SIVR16. Equivalent in Bajaj, Crompton, Usha, and Orient as approved by GE.

Supply and fix Exhaust Fan of size 380 mm sweep with louvers, with metal body AC 230 V, 50 Hz, 1400 RPM and connecting to ceiling rose terminals with 23/.0076 flexible cable and making good the disturbed surface to match with existing finishes complete all specified and directed. Make: Cat No. Almonard of Havells or equivalent in Usha/Crompton Greaves.

Schedule of Credit (Minus) Rs.13817.50 NOTE: Bidder shall insert credit amount of Rs. 13817.50 as rate in Green field under Col-13.

City Constructie Pvt Ltd (BID ID -3463570)

BHARAT MULTITECH INDUSTRIES PVT LTD (BID ID -3464081)

ASHOK BISWAS (BID ID -3464408)