Internal Renovation and Reuse of Majestic Amdar Niwas Building Mumbai. (Including Electrical work)

Providing and fixing ply panelling made out of 60 x 25mm thick Aluminium pipe frame work of size 600 x 600 mm center to center or as per site condition covered by 12mm thick marine plywood of the requisite manufacture viz Anchor/Century/Kenwood /Duro/Jet equivalent generally confirming to I.S. 710-1980 finished with 12mm plywood with antitermite treatment to all plywood and wood work etc complete as per Architect's Drawing and instruction of Engineer in charge

Providing and fixing full height 3.5 to 4mm thick veneer finish partition at made out of 63 x 38mm thick Aluminium Pipe frame work of size 600 x 600 mm center and center or as per site condition covered by 12mm thick marine plywood of the requisite manufacture viz Anchor/Century/Kenwood /Duro /Jet or equivalent generally confirming to I.S. 710-1980 finished with 3.5 to 4mm thick matching Greenply veneer (Wood Crests) of approved colour kenwood stain wall nut grooves and in matching veneer pattern and design Exluding melamine polishing and including antitermite treatment to plywood and wood work with ten year guarantee bond etc including all leads and lifts etc complete as per Architect's Drawing and instuctions of the Engineer in charge

Providing and fixing on-site full ht. Solid BTC wood Folding Shutters with louvered shutter arrangement of Six Shutters size 0.65m x 2.3m height per shutter with BTC Wooden Door frame c/s 100 x 130mm and fixing of bevling clear Glass of 10mm thick with Four glass panel per shutter with 1.25 inch bevelled in all sides of glass panel fitting with lipping patti etc as per Architect's Drawing a instructions of Engineer In Charge

Providing and fixing 3.5 to 4mm thick veneer finished wall paneling with moulding design made out of 50 x 50 mm thick (finish size) CCTW frame work of size 600 x 600mm center or as per site condition covered by 12mm thick marine plywood of the requisite manufactures viz Anchor/Century/Kenwood /Duro /Jet or equivalent generally confirming to IS 710-1980 finished with 3.5 to 4mm thick approved machines Greenply veneer (wood crest) of approved colour kenwood stain wall rut grooves and in matching veneer pattern and design excluding melamine polishing and antitermite treatment to plywood and wood work with ten year guarantee bond etc including all leads and lifts etc complete as per Architect's Drawing and instuctions of the Engineer in charge.

Providing, supplying, fabricating and fixing aluminium composite panel cladding in colour of approved shade made out of 4mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core following NBC part 4 fire and life safety (having 2 hours fire resistance in accordance to ASTM E-119-12 and BS 476 part 6 & 7 class O) sandwiched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA 3105 grade) The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / lumiflon based fluoropolymer resin (having 70:30 ratio of PVDF and Acrylic) Coating of approved colour and shade on external face and polymer (service) coating on other face as specified using stainless steel screws, nuts, bolts, washer, cleats, weather silicon sealant (overall sights of ACP shall not be less than 7 kg/sqmt.) fixed on aluminium frame made out aluminium polo pipe 40 mm x 20 mm x 2 mm thick of standard make. The frame work of verticle member at 600 mm c/c and horizontal 4 members at desired specing to accomodate desired design of panelling, including labour etc complete. as directed by Engineer In Charge.

Providing and fixing and replacing damaged teak wood with well-seasoned BTC wood for door and window frames and members of decorative frame of the same original design size and pattern including all moulding, rebating holdfasts and any other necessary fitting and finishing with one coat of primer complete.

Providing and fixing seasoned burma teakwood double leaf/single leaf door shutter partly panelled and partly glazed having its vertical member size 100 mm x 63mm thick top bottom also in same size and 12mm thick toughened glass with all dhar polished and 35mm bevelled all sides including decorative brass palladium make hinges of size 125mm x 50mm x 3mm thick with decorative stopper and mortise handle as per architectural details drawing complete.

Providing and fixiing 4" x 4" old BTC moulding on wall or any surface by cutting and mould in CNC moulding machine complete as per Architect Drawing

Provding and fixing 3.5 to 4mm thick veneer based inverted ceiling with vertically supported CCTW frame work of size 600 x 600mm center or as per site condition covered by 12mm thick marine plywood and bottom size 19mm Marine plywood of the requisite manufacture viz Anchor/Centruy /Kenwood /Duro/Jet or equivalent generally confirming to IS 710-1980 finished with 3.5mm to 4mm Greenply veneer (wood crrests) sheet of approved colour grooves and in matching pattern Exluding melamine polish and desing including oil paint and antitermite treatment to plywood and wood work with three year guarantee bond etc including all leads and lifts etc complete as per Architect's Drawing and instruction of the Engineer in charge

Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc.all complete.

Providing & Fixing in position, Acoustical Ceiling made from Rigitone 8/18 perforated panels on approved heavy duty G.I. frame, ceiling channels at 300 c to c, & intermediate channels not more than 1200 c to c, suspended with Hangers from Roof, in front of 1000 Gsm synthetic wool 50 mm thick, with Paint, including cost of required CutOuts, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete

Providng and supplying Glass Wool (60mm thick and 20kg/m3 density) laying evenly above the false ceiling to reduce noise and heat from roof including all leads and lifts etc complete as per instruction of engineer in charge

Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. Applying Asian / Berger / Nerolac / Dulux Paints or equivalent wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hours After applying Asian / Berger / Nerolac / Dulux Paints or equivalent acrylic wall putty with appropriate proportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45 % or 65 to 70 % by roller. (With prior approval of S.E.)

Providing and fixing 53 cm Deep Low height Storage Unit at require location less than 1.35meter height by using 18 to 19mm thick marine ply of requisite manufacture generally confirming ot IS 303/IS 710-1980 for frame , internal verticals, horizontal divisions, openable shutters, 6mm thick marine ply back, with necessary locks, handles hardware, lipping (BTC) moulding etc, The external sides shall be finished with 4mm thick veneer sheet finished with pattern with grooves externally and melamine polish and all internally sufrace with two coats of freanch polish with anti termite treatment to plywood & wood work internally including all leads and lfits etc complete as per Architects Drawing and instruction of Engineer in charge

Providing and fixing differenct size of Table made out of 19mm thick marine plywood of the requisite manufacture ie Anchor/ Century / Kenwood/ Greenply or equivalent generally confirming to IS 710-1980 for Top vertical side and 6mm & 12mm thick marnie plywood for back & drawer with necessary BTC wood liping and moulding, The external shall be finished with 3.5 to 4mm thick Greenply Veneer (wood crrests) sheet Excluding melamine polish and internal shall be finished laminate 0.80mm thick (Royale Touche) with three years guarantee on requisite stamp paper etc complete as per drawing and instructions of Engineer in charge

Supplying glass table top 8 mm thick in required size and shape including finishing the all side edges machnically smoothly etc. complete.

Providing and applying melamine polish of required finish to the wood work by spray machine including knotting and preparing the even surface by scraping, applying French polish , scaffolding if required etc. complete. Note: The work to be executed on prior approval of Superintending Engineer will be necessary.

Supplying Zinc concealed door closer as per approved sample by the Engineer in charge with all lead and lifts etc. complete and stacking wherever directed.

Providing and fixing 20 mm thick superior veneer board pelmet box 150 to 200 mm wide to doors or window frames including 20mm dia. Aluminium curtain rod with sockets and finishing with french polishing (without top) etc. complete.

Providing and fixing Aluminium curtain channel box 3/4" with powder coating including runner bracket and necessary fitthing all leads and lift etc complete etc comple as per instruction of the engineer in charge

Providing and fixing silk, velvet cloth curtain of required colour and design as directed by the architect Item to including stiching, hanging heavy curtains of approved fabric on the door to required length duly stitched with 25mm fold french pleting at every 50mm center , haming , hook, ribons tapes , and bottons etc item includs 6"- 8" long silk tassle ropes and tie back to pull the curtain and tie to hook along with tassles along the edges, scallops , or valances eye ring of curtain ring for hanging of curtains etc complete (Basic price of fabrics Rs.1350/mtr) Item to also include embroidery of the emblem on the valances in approved shade and thread on the cloth. Adequate samples need to be provided before the final execution of the item

Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain (Ball) system with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work)

Providing & Fixing frosted film manufactured by 3 M approved equivalent on glass partition wherever required as per the instruction of Architect.

Providing & Supplying centre pivoted revolving mid back visitor chair which frame made out of CCTW section or adequate size of frame and SS form in back side with 6mm marine plywood as per standard ISO for covering from back, seat & arm rest having size of back depth 710mm, width 750mm and having height of 1200 to 1300 mm and seat height 425 to 475 mm (+/-20mm) with CCTW five legs with Push back arrangement. The chairs shall have high density moulded 360 revolving on suitable base. And have gas lift, heavy duty twin wheel casters to take minimum of 95Kg/caster with one having height adjustment and other to arm rest. The chair shall be provided high quality Napa leather approved make & shade by Architect & Engineer in Charge . All exposed CCTW surface will have to be finished in melamine polishing as directed by Engineer in charge

Providing & Fixing in position well seasoned wooden Lounge Chair with arms of size 750mm in length, 750 mm in width and 750mm in height'. The frame consisting with of well seasoned 50x50mm size of teak wood in front & back legs in one piece each without cuts or joinary with arms & bracing of each sides. The seat is set at a height of 450–480 mm from the floor, featuring a 100–120 mm thick removable cushion for enhanced comfort. The backrest rises 500–550 mm above the seat level, providing supportive ergonomics, while the armrests measure 630–680 mm from the floor, with partially upholstered panels for comfort and wooden edges for a refined finish. The legs of the chair are constructed from solid wood with precision-turned detailing, contributing both strength and traditional character. Each leg is approximately 300–350 mm in height, tapering gradually from a 50 mm diameter at the top to about 30 mm at the base. The legs & arms having carving & heritage type design shown in drawings The chair shall have to be completed with high quality of approved & make upholstery fabric upto Rs. 3500/meter. including necessary brass hardware. All exposed wooden surfacses shall be finished with melamine polish etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Supplying three seater sofa having size 2030 x 725 x 435mm height made out of specified size of CCTW section or adequate size of frame with 6mm thick marine plywood as per standard ISO for covering from back & arm rests, Using 100mm thick branded quality form covered one 25mm soft form and arms having 50 x 50 mm CCTW frame and 50 density branded form covered 25 mm plain soft arm. All work covered with high quality upholstery approved make Napa leather of approved colour as directed by Architect & Engineer in charge the necessary and essential hardware, jute, manjarpatt cloth, casement spring etc. will be have good and approved make. All exposed surface will have to be finish with melamine polish and completed as directed by engineer in Charged.

Providing & Fixing in position well seasoned wooden Private D

Providing and Supplying BACK EXTENSION DIMENSIONS(LxWxH): 121.1x72.5x93.3cm 47.7x28.5x36.7in NW: 40kg/89lbs

Providing and Supplying DUMBBELL RACK: to keep dumbbells DIMENSIONS(LxWxH): 1580x814x982mm 62.2x32x38.7in

Providing and Supplying HANDLES : for different form of excercises Bicep rod - 02 Nos V shape rod - 02 No Dshape rod x 02 Nos

Supplying & Providing & Fixing in position Clean Dish Rack Table With Five shelf having size L 54" x B 24" x H 72" with SS Body, SS legs.The rack is constructed with a robust SS body and four spacious horizontal shelves, each shelf made from 1.2 mm thick SS 304 grade. The supporting vertical legs are made from square SS tubular sections of 38 mm x 38 mm with a thickness of 1.5 mm. Each shelf is evenly spaced to accommodate large and small items, with smooth edges and a polished finish. The unit is designed with adjustable nylon bullet feet for leveling on uneven floors. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Masala Trolley having size L 20" x B 24" x H 34" with SS Body, SS legs. The trolley body, including side panels, top, and shelves, is fabricated from 1.2 mm thick SS 304 grade sheets, while the drawers are made of 1.0 mm thick SS 304 sheet for a lightweight yet robust design. The internal partitions are also constructed from SS 304 with a thickness of 0.9 mm to maintain structural strength. The legs are made of 38 mm x 38 mm SS square tubular sections with

Providing & Fixing in position Work Table for Banquet with 02 Under shelf with SS platform having size L 72" x B 24" x H 34" with 6" skirting board above platform with SS legs. The table top is constructed from 1.6 mm thick SS sheet, reinforced with a 150 mm height skirting board above the platform on the rear side. The unit is equipped with 02 under shelves, each fabricated from 1.2 mm thick SS sheet, supported with stiffeners for added load-bearing capacity. The supporting framework consists of heavy-duty SS legs of 38 mm diameter constructed from 1.6 mm thick tubular stainless steel, fitted with adjustable bullet feet for leveling and stability on uneven surfaces. All welding joints are TIG-welded, smoothly ground, and polished for a clean finish including necessary frame work & bracing to achive good stability. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing and applying plaster / wall punning with plaster of paris (with plaster of paris material of Ambuja / Mor Chap or equivalent make) in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface (Excluding rough cast plaster) in all position including preparing and Finishing the surface scaffolding etc.complete

Providing & Fixing in position well-seasoned wooden Double Bed of size 1950mm in length, 1800mm in width having Architectural view. The main structural frame, including headboard, footboard, and side rails, shall be constructed from well seasoned tekwood with a minimum thickness of 25 mm. The turned wooden legs, integrated into the corner posts, shall be no less than 70 mm in diameter and 150 mm high, fitted with protective nylon pads. Upholstered panels in both headboard and footboard shall be inset with 12 mm thick plywood padded with 20 mm high-density foam with 32–40 density, Side rails will be connected using steel brackets and include internal reinforcement. 20mm thick marine plywood with veneer finish as a top, bottom, sides, legs & headboard shall in carving & heritage type design shown in drawings. The wooden work shall be finished with melamine polish & essential fixtures, hardware & fastening in brass etc., completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Supplying CCTW chairs with arms as per design curved with adequate size of arms & legs and chair seat/ back shall have to be finish with high quality upholstery approved make Napa leather of approved colour as directed by Architect & Engineer in charge the necessary and essential hardware, jute, manjarpatt cloth etc. will be have good and approved make. All exposed surface will have to be finish with melamine polish (Chair Size : 530 x 460mm)

Providing & Fixing in position well seasoned wooden Podium size of 1200mm in height , 700mm in lenght and 400mm in depth having Architectural view as shown in Architect's drawings. The podium is fabricated using teak wood panels with a thickness of 18 mm for the body and 25 mm thick top platform. The podium front is adorned with a central raised wooden panel framed with bevelled edging, highlighting the natural wood grain pattern. On either side, two fluted vertical wooden columns with Corinthian-style carved capitals. 1 shelf of size 345x185mm consist in the podium table. All exposed wooden surfacses shall be finished with melamine polish etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Supplying Single seater sofa chair having size 815 x 815 x 430 mm (+/- 50mm) height made out of specified size of CCTW section or adequate size of frame with decorative legs & 6mm thick marine plywood as per standard ISO for covering from back & arm rests, Using 100mm thick branded quality form covered one 25mm soft form and arms having 50 x 50 mm CCTW frame and 50 density branded form covered 25 mm plain soft arm. . All work covered with high quality upholstery approved make Napa leather of approved colour as directed by Architect & Engineer in charge the necessary and essential hardware, jute, manjarpatt cloth, casement spring etc. will be have good and approved make. All exposed surface will have to be finish with melamine polish and completed as directed by Engineer in Charged.

Providing and Supplying CCTW Foot rest with adequate size of legs and top shall have to be finish with high quality upholstery approved make Nappa leather of approvedcolor as directed by Architect & Engineer in charge the necessary and essential hardware, jute, manjarpatt cloth etc. will be have good and approved make. All exposed surface will have to be finish with melamine polish (Size : 450 x 400 mm)

Providing & Supplying executive table made out of CCTW frame, legs, top, internal vertical & horizontal partition including different sizes of moulding wherever directed by Engineer in Charge drawer and sides closing by CCTW adequate sizes. The wood work shall have to be finishing with melamine polish. The hardware and necessary & essential fittings shall have to be approved make &shade require to be approved from Architect & Engineer in Charge. (Table size 2100 x 1050 x 810 mm)

Providing & Fixing in position Work Table with 02 Under shelf with SS platform having size L 24" x B 30" x H 34" with 6" skirting board above platform with SS legs. The table features a robust stainless steel platform top with a thickness of 1.5 mm, reinforced with stainless steel channels. It is designed with two under shelves fabricated from 1.2 mm thick stainless steel sheet. Each shelf is fixed on strong support channels and can bear heavy loads without deformation. The vertical support legs are made of 40 mm x 40 mm square stainless steel tube with 1.5 mm thickness. The edges and corners of the worktop are smooth, with a 45 mm turn-down on all sides and rounded corners. The table is mounted on heavy-duty stainless steel legs with adjustable nylon bullet feet. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Single board SS Sink (Sink Size : L 18" x B 18" x H 12") with SS platform having size L 24" x B 30" x H 34" with 6" skirting board above platform with SS legs. The overall unit is constructed from stainless steel with a uniform material thickness of 1.5 mm for the sink bowl and 1.2 mm for the platform. The sink top is designed with a 150 mm high rear splash guard to prevent water spillage on the wall. The unit is mounted on heavy-duty SS tubular legs of 38 mm diameter with 16-gauge thicknes

s, complete with adjustable bullet feet for stability on uneven flooring. The frame is reinforced with horizontal cross-bracing on all four sides for enhanced rigidity. The sink is provided with a standard SS waste coupling and drain arrangement for efficient water disposal. The entire unit has smooth, polished, and rounded edges. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Work Table with 02 Under shelf with SS platform having size L 18" x B 24" x H 34" with 6" skirting board above platform with SS legs. The top platform is fabricated from 16-gauge (1.5 mm thick) SS 304 sheet. The table is equipped with two under shelves made of 18-gauge (1.2 mm thick) SS 304 sheet. The supporting framework consists of 40 mm diameter SS 304 tubular legs with 1.6 mm wall thickness. Each leg is fitted with adjustable bullet feet in SS to ensure leveling on uneven floors. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Crockery Rack with 05 shelfs with SS body having size L 29" x B 29" x H 72". Each shelf is fabricated from SS sheet of 1.2 mm thickness with smooth finishing. The vertical supports are manufactured from 38 mm x 38 mm square SS pipes with 16 SWG thickness. The horizontal shelf frames are reinforced with SS stiffeners beneath each level to prevent sagging under heavy loads. The entire rack stands firmly on SS adjustable bullet legs (38 mm Ø with 16 SWG thickness), allowing proper leveling on uneven surfaces while maintaining hygiene clearance from the floor. All welds are finished smoothly with ground edgesincluding necessary frame work & bracing to achive good stability. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Work Table with 02 Under shelf with SS platform having size L 24" x B 24" x H 36" with 6" skirting board above platform with SS legs. The top platform is fabricated from 16-gauge (1.5 mm thick) SS 304 sheet. The table is equipped with two under shelves made of 18-gauge (1.2 mm thick) SS 304 sheet. The supporting framework consists of 40 mm diameter SS 304 tubular legs with 1.6 mm wall thickness. Each leg is fitted with adjustable bullet feet in SS to ensure leveling on uneven floors. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Work Table with 02 Under shelf with SS platform having size L 30" x B 24" x H 34" with 6" skirting board above platform with SS legs.The top platform is fabricated from 16-gauge (1.5 mm thick) SS 304 sheet. The table is equipped with two under shelves made of 18-gauge (1.2 mm thick) SS 304 sheet. The supporting framework consists of 40 mm diameter SS 304 tubular legs with 1.6 mm wall thickness. Each leg is fitted with adjustable bullet feet in SS to ensure leveling on uneven floors. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Service Pick Up Table with 02 Under shelfs having size L 72" x B 29" x H 34" with SS legs. iThe worktop fabricated from 16 SWG (1.5mm thick) SS 304 grade sheet, reinforced with SS stiffeners. The table is provided with two under-shelves made of 18 SWG (1.2mm thick) SS sheet,. above the worktop, the unit features two overhead shelves, the first shelf mounted at 450mm height from the table top and the second shelf at 300mm above the first one, fabricated from 18 SWG (1.2mm thick) SS sheet. The vertical support sections are made of circular SS 304 pipes of 38mm diameter with 16 SWG thickness while the horizontal frame sections are made from 38mm x 38mm SS 304 square tube of 16 SWG thickness. The table legs are fitted with adjustable bullet feet for leveling on uneven surfaces. All welding joints are argon-welded, ground smooth, and polished to a matt finish. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position SS Sink with Table & 02 Under shelfs (Sink Size : L 18" x B 18" x H 12") with SS table top having size L 72" x B 29" x H 34" with 6" skirting board above table top with SS legs, drainge pipe & waste coupling. The unit is fabricated entirely from high-quality 304-grade stainless steel with a material thickness of 1.5 mm for the table top and sink bowl. The table is supported by sturdy square tubular stainless steel legs of 40 mm × 40 mm with 1.5 mm thickness, equipped with adjustable bullet feet for floor leveling and stability. Two under-shelves are provided – the first being a solid SS sheet under-shelf for utility storage and the second being a slatted shelf at the bottom for proper ventilation and drainage, both constructed with 1.2 mm thick SS sheet and tubing support. The sink unit is integrated with a waste pipe connection and fitted with a standard faucet mounted above the sink bowl for efficient water flow. The entire construction is fully welded and polished to a smooth matt finish. The table corners are rounded and all weld joints are ground flush to eliminate dirt traps. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing unit of Dirty Dish Landing Table with SS table having size L 48" x B 29" x H 34" with 6" skirting board above table top with SS legs. stainless steel table top constructed from 16 SWG (1.5mm thick) SS sheet. The frame is built entirely from 38mm x 38mm square stainless steel tubular sections with 1.6mm thickness. Horizontal bracing members and rack supports are fabricated from 25mm x 25mm square SS sections with 1.6mm thickness. each fabricated from stainless steel wire with slotted arrangements to securely hold plates in a vertical position for drainage and drying. Each rack is supported with drip trays made of 1.2mm thick SS sheet, allowing efficient water collection. The unit stands on four SS legs fabricated from 38mm x 38mm square tubes, each fitted with heavy-duty nylon adjustable bullet feet for leveling on uneven surfaces. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Work Table with 02 Under shelf for Veg. Cutting with SS table having size L 78" x B 29" x H 34" with 6" skirting board above table top with SS legs. The top platform is fabricated from 16-gauge (1.5 mm thick) SS 304 sheet. The table is equipped with two under shelves made of 18-gauge (1.2 mm thick) SS 304 sheet. The supporting framework consists of 40 mm diameter SS 304 tubular legs with 1.6 mm wall thickness. Each leg is fitted with adjustable bullet feet in SS to ensure leveling on uneven floors. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Service pick up Counter Covered from three sides & necessary under shelfs having size L 72" x B 24" x H 34" & with an additional 450 mm + 300 mm double overhead shelf supported on sturdy SS tubular frames. Below the worktop, the unit is provided with under shelf fabricated from 1.2 mm thick SS sheet. The shelves are mounted on 38 mm dia SS tubular legs with adjustable bullet feet for floor leveling. The main worktop is constructed from 1.5 mm thick stainless steel sheet reinforced with SS stiffeners. The counter is covered from three sides (rear and both lateral sides) with SS cladding of 1.2 mm thickness. The counter incorporates three smoothly sliding drawers below the worktop, made from 1.0 mm thick stainless steel sheet with recessed handles, suitable for cutlery, service accessories, and lightweight storage. The overhead shelf section is supported on 38 mm dia SS round tubular vertical posts with horizontal shelf panels made of 1.2 mm SS sheet. SS 304 grade use etc. completed as directed by Engineer in Charge.

Supplying & Providing & Fixing in position Water Cooler having size L 24" x B 20" x H 60" and water storage capacity 120 Liters. SS body with Heavy duty motor. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixi

ng in position Dirty Dish Landing Table with SS table having size L 42" x B 24" x H 34" with 6" skirting board above table top with SS legs. stainless steel table top constructed from 16 SWG (1.5mm thick) SS sheet. The frame is built entirely from 38mm x 38mm square stainless steel tubular sections with 1.6mm thickness. Horizontal bracing members and rack supports are fabricated from 25mm x 25mm square SS sections with 1.6mm thickness. each fabricated from stainless steel wire with slotted arrangements to securely hold plates in a vertical position for drainage and drying. Each rack is supported with drip trays made of 1.2mm thick SS sheet, allowing efficient water collection. The unit stands on four SS legs fabricated from 38mm x 38mm square tubes, each fitted with heavy-duty nylon adjustable bullet feet for leveling on uneven surfaces. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Pre Rinse Two Sink Unit (Sink Size : L 18" x B 18" x H 12") with SS table top having size L 45" x B 29" x H 34" with 6" skirting board above table top with SS legs, drainge pipe & waste coupling. The sink bowls are manufactured from 1.2 mm thick stainless steel, with smooth radius corners to facilitate effortless washing and drainage. The table top itself is fabricated from 1.5 mm thick SS 304 grade. he unit is supported by robust square-section SS legs made of 38 mm x 38 mm tubing with a thickness of 1.6 mm, reinforced with horizontal cross-bracing for added stability. Adjustable SS bullet feet are provided at the base for leveling on uneven surfaces. The entire assembly is TIG welded and polished, ensuring a smooth finish with no sharp edges. SS 304 grade use etc. completed as directed by Engineer in Charge. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Clean Dish Rack Table With Five shelf having size L 36" x B 24" x H 72" with SS Body, SS legs.stainless steel table top constructed from 16 SWG (1.5mm thick) SS sheet. The frame is built entirely from 38mm x 38mm square stainless steel tubular sections with 1.6mm thickness. Horizontal bracing members and rack supports are fabricated from 25mm x 25mm square SS sections with 1.6mm thickness. each fabricated from stainless steel wire with slotted arrangements to securely hold plates in a vertical position for drainage and drying. Each rack is supported with drip trays made of 1.2mm thick SS sheet, allowing efficient water collection. The unit stands on four SS legs fabricated from 38mm x 38mm square tubes, each fitted with heavy-duty nylon adjustable bullet feet for leveling on uneven surfaces. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Pot Rack With Four shelf having size L 48" x B 24" x H 72" with SS Body, SS legs.The rack is constructed with a robust SS body and four spacious horizontal shelves, each shelf made from 1.2 mm thick SS 304 grade. The supporting vertical legs are made from square SS tubular sections of 38 mm x 38 mm with a thickness of 1.5 mm. Each shelf is evenly spaced to accommodate large and small items, with smooth edges and a polished finish. The unit is designed with adjustable nylon bullet feet for leveling on uneven floors. SS 304 grade use etc. completed as directed by Engineer in Charge.

Supplying & Providing & Fixing in position Pulverizer having standard size or as directed by Engineer in Charge. This robust pulverizer machine is powered by a high-performance 5 horsepower motor, operating on a 3-phase power supply. Designed for heavy-duty grinding tasks, it efficiently pulverizes various materials into fine powders. Whether you're processing grains, spices, herbs, or other solid substances. Entirely made of high quality stainless steel, Easy operability. SS 304 grade use

Supplying & Providing & Fixing in position Bussing Trolley having size L 24" x B 36" x H 34" with 02 or 03 under shelfs, SS Body, SS legs. The trolley is available in configurations with either 02 or 03 under-shelves, each fabricated from 1.2 mm thick SS sheet with raised edges. The frame and supporting legs are manufactured from 38 mm diameter SS round pipes of 16 SWG thickness. The trolley is fitted with four heavy-duty swivel castor wheels of 125 mm diameter, two of which are provided with brakes for added safety and controlled movement. The edges and corners are smoothly rounded. including necessary frame work & bracing & easily moveable with four castor wheels. SS 304 grade use etc. completed as directed by Engineer in Charge.

Supplying & Providing & Fixing in position Cash Counter having size L 30" x B 24" x H 34" with 10 The unit features a 10-inch high vertical fascia, seamlessly covered on three sides & 02 drawers, each integrated with an advanced locking system with full SS Body, SS legs. The drawers operate on smooth sliding channels, allowing effortless handling even under heavy load conditions. The unit features a 10-inch high vertical fascia, seamlessly covered on three sides.Below the drawers, the counter is designed with two open storage shelves.The shelves are fabricated from 18-gauge SS sheet (1.2 mm thickness).The top platform is reinforced with 16-gauge SS sheet (1.5 mm thickness). The SS legs are equipped with adjustable bullet feet to ensure stability on uneven surfaces. All edges are rounded and finished with smooth polishing. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in position Flap Door having size L 20" x B 24" x H 44" flap door with rigid shutters with push opening and return by means of a spring. Constructed with a full stainless steel frame and reinforced wooden or metal-faced panels, each shutter has a thickness of 38 mm to 45 mm. With Oval or Round window with 8 mm toughened clear vision glass with a stainless steel frame. The shutters are equipped with a push-to-open mechanism and are self-returning by means of a concealed spring system. The bottom section of the shutters is reinforced with a 1.2 mm thick stainless steel kick plate while the door edges and corners are strengthened with 1.0 mm SS beading. The hinges are made of heavy-duty stainless steel with a double-swing mechanism. Intermediate opening edges are brought to the resting position back by the over mentioned spring including necessary hardware & fixtures etc.completed.as directed by Engineer in Charge.

Providing & Fixing in position Service Pick Up Counter with One Glass OHS having overall size L 72" x B 24" x H 34" and one overhead shelve above top 20". SS Body & SS panelling on three sides, SS Uprightes, SS Bullet feet, food warmer, plate warmer etc. Pick Up Counter is used to keep cooked dishes under food warmer to be served to customers. It is also used to store stuff under given shelves. The unit is fabricated using 1.5 mm thick SS top, 1.2 mm thick panelling, and 1.0 mm thick under-shelf supports, mounted on sturdy 38 mm x 38 mm SS tubular legs with adjustable bullet feet for stability and floor leveling. The counter comes with a front service rail for ease of access and smooth service operation. SS 304 grade use etc. completed as directed by Engineer in Charge.

Providing & Fixing in positin Work Table with 02 Under shelf and one overhead shelf and one overhead fruit basket above the top having size L 48" x B 24" x H 34" & O/H 18" + 12". SS Body & SS panelling on three sides, SS Uprightes, SS Bullet feet. The top working surface is constructed from 1.5 mm thick SS sheet reinforced with a sound-dampening underlayer. The table includes two under shelves, made of 1 mm thick SS sheet. Additionally, the unit is equipped with one overhead shelf fabricated from 1 mm thick SS sheet, supported on sturdy vertical SS pipes of 38 mm diameter and 16 gauge thickness. An overhead fruit basket is integrated above the top shelf, designed with SS wire mesh of 5 mm thickness to hold. The table is designed with SS panelling on three sides (rear and two sides), fabricated from 1 mm thick SS sheet. The front side remains open for accessibility, while the under-shelves include one section with sliding SS shutters and one section open with compartme

nts for easy storage segregation. The unit is mounted on sturdy SS tubular legs of 38 mm diameter, 16 gauge thickness, fitted with adjustable nylon bullet feet for floor levelling. SS 304 grade use etc. completed as directed by Engineer in Charge.

Supplying & Providing & Fixing in positin Storage Rack with 05 shelves having size L 26" x B 29" x H 72" with SS Body, SS legs.The rack is constructed with a robust SS body and four spacious horizontal shelves, each shelf made from 1.2 mm thick SS 304 grade. The supporting vertical legs are made from square SS tubular sections of 38 mm x 38 mm with a thickness of 1.5 mm. Each shelf is evenly spaced to accommodate large and small items, with smooth edges and a polished finish. The unit is designed with adjustable nylon bullet feet for leveling on uneven floors. SS 304 grade use etc. completed as directed by Engineer in Charge..

Supplying & Providing & Fixing in position Work Table with Sink & 02 Half Under shelfs (Sink Size : L 18" x B 18" x H 12") with SS table top having size L 96" x B 24" x H 34" with 6" skirting board above table top with SS legs, drainge pipe & waste coupling. The SS table top is manufactured with a thickness of 1.5 mm, reinforced with sound-deadening support, and has smooth rounded edges. At the rear, a backsplash of 150 mm height and 1.2 mm thickness. The table is supported on stainless steel tubular legs of 40 mm diameter and 1.5 mm thickness, with adjustable bullet feet for levelling on uneven floors. Two half under shelves, fabricated from 1.2 mm thick stainless steel. SS 304 grade use etc. completed as directed by Engineer in Charge.

Supplying & Providing & Fixing in position Exhaust Blower : Type: - Co-axial, Centrifugal Exhaust Blower CFM - 6000 Units, Pressure - 30 mm Motor - 3HP, 440 V, III Phase, 960 RPM, Make : Hindustan etc. completed or as directed by Engineer in Charge.

Supplying & Providing & Fixing in position Labour, Installation -Fabrication of Ducting at site, M.S. Brackets/Holders where required, canvas Rope packing, canvas cloth connector, Anti - vibration pads for Blower etc. completed or as directed by Engineer in Charge. (FRESH AIR SYSTEMS)

Providing and Supplying BARBELL RODS : for different form of excercises 7 feet long rod x 03 Nos 4 feet long rod x 03 Nos 4 feet EZ rod x 02 Nos

Providing & Fixing in position well seasoned wooden Massage Bed of size 1850mm inn length, 650 mm in width. The cushion platform is made from 16mm thick plywood. It is layered with 40 density foam to provide superior comfort and support, and finished in high-quality leatherette that is oil- and waterproof for easy cleaning and maintenance. The bed features a lightweight, foldable aluminum frame that ensures easy portability without compromising stability. It includes an adjustable face cradle and a hanging arm shelf to enhance client comfort during use. The height height adjusted from 600mm to 850mm is adjustable through telescopic legs, allowing customization for ergonomic needs. The entire unit folds compactly into a carry case with secure clasps and a handle, with all accessories neatly stored inside. The massage bed has 2-inch sponge, with soft cushioning etc. completed as per the Architect's drawings and instructions of the Engineer in Charge.

Providing & Fixing in position Salon Chair made of heavy-duty and sturdy steel frame having overall dimensions of 838mm (W) x 813mm (D) x 914mm (H) with a seat width of 508mm. It is upholstered in premium black PU leatherette that is both water-resistant. The backrest showcases deep button tufting and decorative nail-head trim. For comfort and durability, the seat is padded with high-density foam approximately 100mm thick, while the backrest and armrests are cushioned with foam measuring about 65m and 50mm respectively. The chair’s frame is constructed from heavy-duty steel with a chrome finish, supported by a sturdy chrome-plated steel base with a diameter of 585, stab Equipped with a hydraulic pump system, the chair supports up to 150kg and allows for height adjustment between 457mm and 610mm via a convenient foot-operated pedal. Additionally, a stainless steel footrest. It shall be rotate 360 degree with adjustable hydrulic up and down including movable arm rest mechanically. The chair shall be finish with PU leather and exposed steel body surface is easy to clean and maintain in hygenic condition etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Fixing in position well well-seasoned wooden Single Bed of size 900mm in width and length in 1950mm having Architectural view. The headboard stands approximately 1143 mm high, while the footboard reaches a height of about 750 mm. Both the headboard and footboard feature inset natural cane panels, traditionally hand-woven from rattan, with a thickness of approximately 6 mm to 12 mm. These panels are housed within a solid wood frame with molded edges and a thickness of approximately 38 mm.The frame consisting with of well seasoned 2''x2'' size of teak wood with 20mm thick marine plywood with veneer finish as a top, bottom, sides, legs & headboard shall in carving & heritage type design shown in drawings. The four bed posts are turned in a traditional style with carved detailing, each approximately 76 mm in diameter at their widest point and rising to match the headboard and footboard height respectively. The legs taper down to square bases for stability and are roughly 450 mm in length from floor to frame base.The side rails, which connect the headboard and footboard, are approximately 25 mm thick and 200 mm in height, providing a sturdy frame for the mattress and support slats of 18 mm thick. The wooden and exposed member shall be finishing with melamine polish & essential fixtures, hardware & fastenening in brass etc. completed.

Providing & Fixing in position well seasoned wooden Recliner chair in Architectural view. The chair’s overall dimensions are 1000 mm in height, 900 mm in width, and 900 mm in depth, with a seat height of 430 mm from the floor, a seat depth of 550 mm, and an armrest height of 620 mm. The seat and back are padded with multi-layered, high-resilience polyurethane foam, with the seat cushion comprising a base layer of high-density PU foam (35 kg/m³ density, 100 mm thick) for support, topped with a softer comfort foam layer (28 kg/m³, 50 mm thick), and the backrest using medium-density PU foam (30 kg/m³, 70 mm thick), shaped ergonomically to provi

de lumbar support and upper back comfort, while the arms include soft foam padding (25 kg/m³, 20 mm thick) over the frame. Upholstered in top-grain aniline-dyed Napa leather . The leather stretched tightly over the foam and frame for a tailored appearance, featuring minimal seam lines for a clean aesthetic, and includes a decorative green cushion made of cotton or velvet fabric of approximately 200 gsm as an accessory. The legs are crafted from teakwood stained in a dark walnut finish, each leg measuring approximately 40 mm x 40 mm in cross-section at the thickest point and tapering toward the floor, angled for stability and mounted into the frame using heavy-duty steel brackets and bolts. The wooden and exposed member shall be finishing with melamine polish & essential fixtures, hardware & fastenening in brass etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Fixing in position well seasoned wooden T.V. Unit of size 1800mm (W) x 500mm (H) x 450mm (D), shown in Architect's drawing. It is constructed primarily from engineered wood with a high-quality natural wood veneer finish. The main framework of the unit, including the top panel, side panels, and bottom base, is made from 18mm thick marine plywood, which offers excellent durability and stability. The top panel is designed to support standard flat-screen televisions and decorative items.The unit consisting four drawers two on each side, and a central cabinet with double glass-paneled doors. The drawer faces and the glass door frames are crafted from solid wood (most likely rubberwood or oak) for enhanced strength and traditional visual character. Each drawer is mounted on smooth metal ball bearing runners, with a 15mm plywood base and 12mm side panels for the drawer box construction. The glass inserts in the central cabinet doors are clear tempered glass, segmented with wooden mullions for a windowpane effect. Internally, the central cabinet includes a shelf made from 18mm plywood. The back panel of the unit is likely made from 6mm thick plywood with cable management cutouts to support electronic connections discreetly. Top, bottom, front, and sides shall in carving & heritage type design shown in drawing. The wooden and exposed member shall be finishing with melamine polish & essential fixtures, hardware & fastenening in brass including locking arrangement etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Proving & Supplying CCTW Dining Table having size of 2100 x 915 x 765mm with decorative curved legs, square top with round edges including bracing to top & bottom with required sizes of moulding at all edges as approved by Architect & Engineer in Charge and work shall be finish with melamine polished to exposed surfaces etc. completed. (6 seater)

Providing & Fixing in position well seasoned wooden Hostes Table of size of 900mm in length, 450mm in depth, with a standard height of approximately 1100mm having Architectural view. The primary framework of the desk is constructed using 25mm thick marine plywood while the internal supporting members and structural partitions are made from 25mm thick plywood to enhance load-bearing capacity. The exterior surface is finished with decorative veneer or laminate of 1mm thickness, supported with matching edge banding of 2mm PVC for clean edges and impact resistance. The desk features front and side panels with raised moulding details crafted from 18mm thick Plywood, precisely routed to achieve the panelled design. The corner sections are shaped using laminated curved plywood of 18mm thickness, giving a rounded column effect for enhanced detailing and structural strength. The working table top is made from 25mm thick plywood with a laminate finish. complemented by a 12mm thick plywood skirting detail for visual depth. The base plinth is reinforced with 18mm thick plywood and finished with laminate to protect against floor contact and moisture ingress. Top, bottom, sides, and front elevation shall in carving & heritage type design shown in drawings. The wooden and exposed member shall be finishing with melamine polish & essential fixtures, hardware & fastenening in brass etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Fixing in position well seasoned wooden 02 seater Dining Table having Architectural view. The dining table in Circular or Round shape wooden with a traditional carved pedestal base. The overall dimension of the table measures 750mm in diameter and 750mm in height. The table top is crafted from teakwood with a core thickness of 25mm, reinforced with a solid apron skirting of 75mm height and 20mm thickness around the circumference to provide stability and strength. The edges of the table top are finished with detailed molding for enhanced aesthetics. The central pedestal base consists of a turned hardwood column of 150mm diameter, branching into four curved wooden legs, each 40mm thick, connected to a circular stabilizing base of 30mm thickness and 600mm diameter for firm ground support. The chair has an overall height of 830mm, with a seat height of 450mm, seat width of 450mm, and seat depth of 450mm. The seat base is made from 18mm plywood with a high-density PU foam cushion of 40 density and 100mm thickness. The backrest frame is crafted from teakwood sections of 35mm thickness, shaped into an oval outline with an upholstered insert panel. The seat frame is made of solid wood with a 40mm thickness, housing high-density foam of 75mm thickness for seating comfort. The legs are turned hardwood with a minimum thickness of 40mm at the narrowest section. The chair shall have to be completed with high quality of approved & make upholstery fabric uptoRs. 3500/meter. including necessary brass hardware. All exposed wooden surfaces shall be finished with melamine polish including necessary hardware & fastening in brass etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Fixing in position well seasoned wooden Banquet Sofa - 03 seater having Architectural view. The 3-seater sofa measures 2100mm in length, 750mm in depth, and 850mm in height. The frame is made of 38mm thick seasoned hardwood. The seat base is supported with elastic webbing and zigzag springs. The seat cushions are 150mm thick high-density foam of 32–35 density with a 25mm soft foam topper. The backrest is designed with a deep-button tufted pattern, curved profile, and 100mm thick medium-density foam of 28 density with webbing support. The armrests are rolled with an outward curvature, padded with 75mm thick foam of 28 density over the wooden frame, and proportioned to support relaxed seating. The base has a fabric-covered skirting that conceals the legs. The legs are integrated into the internal frame. Loose back cushions are provided with 100mm thick PU foam filling. . All work covered with high quality of approved & make upholstery fabric upto Rs. 3500/meter. of approved colour as directed by Architect & Engineer in Charge. All exposed surface will have to be finish with melamine polish and completed as directed by Engineer in Charge.

Providing & Fixing in position well seasoned wooden Banquet Sofa - 02 seater having Architectural view. The 2-seater sofa measures 1600mm in length, 750mm in depth, and 850mm in height. The frame is made of 38mm thick seasoned hardwood. The seat base is supported with elastic webbing and zigzag springs. The seat cushions are 150mm thick high-density foam of 32–35 density with a 25mm soft foam topper. The backrest is designed with a deep-button tufted pattern, curved profile, and 100mm thick medium-density foam of 28 density with webbing support. The armrests are rolled with an outward curvature, padded with 75mm thick foam of 28 density over the wooden frame, and proportioned to support relaxed seating. The base

has a fabric-covered skirting that conceals the legs. The legs are integrated into the internal frame. Loose back cushions are provided with 100mm thick PU foam filling. . All work covered with high quality of approved & make upholstery fabric upto Rs. 3500/meter. of approved colour as directed by Architect & Engineer in Charge. All exposed surface will have to be finish with melamine polish and completed as directed by Engineer in Charge.

Providing & Fixing in position well seasoned wooden Banquet Sofa - 01 seater having Architectural view. The 1-seater sofa measures 800mm in length, 750mm in depth, and 850mm in height. The frame is made of 38mm thick seasoned hardwood. The seat base is supported with elastic webbing and zigzag springs. The seat cushions are 150mm thick high-density foam of 32–35 density with a 25mm soft foam topper. The backrest is designed with a deep-button tufted pattern, curved profile, and 100mm thick medium-density foam of 28 density with webbing support. The armrests are rolled with an outward curvature, padded with 75mm thick foam of 28 density over the wooden frame, and proportioned to support relaxed seating. The base has a fabric-covered skirting that conceals the legs. The legs are integrated into the internal frame. Loose back cushions are provided with 100mm thick PU foam filling. . All work covered with high quality of approved & make upholstery fabric upto Rs. 3500/meter. of approved colour as directed by Architect & Engineer in Charge. All exposed surface will have to be finish with melamine polish and completed as directed by Engineer in Charge.

Providing & Fixing in position well well-seasoned, wooden Circular Table of size The table has an overall diameter of approximately 900 mm and a height of 750 mm, designed as a center piece for formal living spaces. The table top is constructed from solid hardwood with a 30 mm thick top surface, finished with a high-gloss polished veneer and highlighted with ornate carved edging. The apron measures 100 mm in height with detailed ornamental carvings along its perimeter. The table is supported on three elegantly curved cabriole-style legs, each measuring 80 mm thick at the upper section tapering to 50 mm at the lower section, embellished with hand-carved floral motifs and scroll detailing. The legs converge onto a circular wooden pedestal base of 600 mm diameter and 50 mm thickness. The finish is executed in a premium antique gold leaf coating with protective PU lacquer. The carved accents are highlighted with subtle shading to emphasize detailing. The table legs shall have finished with curved carving, Architectural view. all necessary hardware & fastening in brass, etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Fixing in position well seasoned wooden 04 seater Dining Table having Architectural view. The dining table is designed with a square-shaped top having an overall dimension of 900mm x 900mm with a standard dining height of 750mm. The table top is constructed using a 25mm thick marine plywood, finished with a high-quality wood veneer. The edges of the table top are rounded with a 3mm solid wood moulding to enhance durability and prevent chipping. The table is supported on a central solid hardwood pedestal base with a circular bottom plate for stability, measuring approximately 400mm in diameter and 40mm in thickness. The pedestal column is crafted from teakwood, with a diameter of 150mm. The chair has an overall height of 830mm, with a seat height of 450mm, seat width of 450mm, and seat depth of 450mm. The seat base is made from 18mm plywood with a high-density PU foam cushion of 40 density and 100mm thickness. The curved backrest is ergonomically designed, reinforced with 16mm plywood backing, and cushioned with 32 density foam at 75mm thickness for optimum comfort. The edges of the upholstery are finished with antique-style nail head trims for decorative detailing. The legs are made of teakwood, each leg being 45mm x 45mm in section at the top, tapering down to 30mm at the base, with an overall thickness of 25mm. The chair shall have to be completed with high quality of approved & make upholstery fabric uptoRs. 3500/meter. including necessary brass hardware. All exposed wooden surfaces shall be finished with melamine polish including necessary hardware & fastening in brass etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Fixing in position well seasoned wooden 02 seater Dining Table with chairs having Architectural view. The dining table is designed with a square-shaped top having an overall dimension of 750mm x 750mm with a standard dining height of 750mm. The table top is constructed using a 25mm thick marine plywood, finished with a high-quality wood veneer. The edges of the table top are rounded with a 3mm solid wood moulding to enhance durability and prevent chipping. The table is supported on a central solid hardwood pedestal base with a circular bottom plate for stability, measuring approximately 400mm in diameter and 40mm in thickness. The pedestal column is crafted from teakwood, with a diameter of 150mm. The chair has an overall height of 830mm, with a seat height of 450mm, seat width of 450mm, and seat depth of 450mm. The seat base is made from 18mm plywood with a high-density PU foam cushion of 40 density and 100mm thickness. The curved backrest is ergonomically designed, reinforced with 16mm plywood backing, and cushioned with 32 density foam at 75mm thickness for optimum comfort. The edges of the upholstery are finished with antique-style nail head trims for decorative detailing. The legs are made of teakwood, each leg being 45mm x 45mm in section at the top, tapering down to 30mm at the base, with an overall thickness of 25mm. The chair shall have to be completed with high quality of approved & make upholstery fabric uptoRs. 3500/meter. including necessary brass hardware. All exposed wooden surfaces shall be finished with melamine polish including necessary hardware & fastening in brass etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Fixing in position well seasoned wooden Dining table with Round shape Sofa of size 2893 x 600mm in width for a Terrace restaurant. The seating structure is fabricated using a 19mm thick Marine plywood framework, The seat base is layered with high-density polyurethane foam 100mm thick, topped with a 25mm thick super-soft foam for plushness. The backrest is constructed with 12mm plywood framing, integrated with 75m

m thick medium-density foam. The base is clad with 18mm thick plywood board finished in a polished veneer. The central dining table for circular or round shape is crafted with an overall diameter of 1350mm and a height of 750mm, proportioned to harmonize with the sofa seating layout. The table top is manufactured from 25mm thick marine plywood board, veneered with natural wood and finished in a semi-gloss polish. Its edges are detailed with a 30mm solid wood moulding . The table is supported by a robust turned solid wood pedestal base, engineered with a 100mm thick central column tapering to a wide 450mm diameter base plate for superior stability. The pedestal and base components are constructed from teakwood, with a minimum thickness of 40mm. The chair has an overall height of 830mm, with a seat height of 450mm, seat width of 450mm, and seat depth of 450mm. The chair frame is manufactured from teakwood for maximum durability. The seat base is made from 18mm plywood with a high-density PU foam cushion of 40 density and 100mm thickness. The curved backrest is ergonomically designed, reinforced with 16mm plywood backing, and cushioned with 32 density foam at 75mm thickness for optimum comfort. The edges of the upholstery are finished with antique-style nail head trims for decorative detailing. The legs are made of teakwood, each leg being 45mm x 45mm in section at the top, tapering down to 30mm at the base, with an overall thickness of 25mm, The sofa & chair shall have to be completed with high quality of approved & make upholstery fabric upto Rs. 3500/meter. including necessary brass hardware. All exposed wooden surfacses shall be finished with melamine polish etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Providing & Fixing in position well seasoned wooden Bar Unit and liquor cupboard of size 4800 x 829mm with liquor cupboard shown As per Architect's drawing. The counter front and sides are crafted from 18mm thick solid hardwood panels with decorative mouldings, reinforced with a 25mm thick internal plywood framework. The counter top is constructed using a 40mm thick seasoned hardwood slab, with rounded bullnose edges of 12mm radius. The base skirting runs along the entire length and depth of the counter, made with 25mm thick solid wood. The corner sections are finished with curved wooden panelling of 18mm thickness. The back side of the counter (service side) is configured with modular storage compartments fabricated from 18mm commercial plywood laminated on both sides, with shelf divisions at 300mm intervals and drawer units with 12mm thick ply bottoms. The entire counter sits on a concealed wooden frame base of 50mm x 75mm section members, The Bar unit and liquor cupboard have top, bottom, sides and front elevation shall in carving & heritage type design shown in drawings. The sides of Bar counter shall have half curve/ round shape and finised with well seasoned wooden plank including curved, carving Architectural moulding to edges of Unit top to good appearance and top shall be finish with the melamine polish and the front & back & sides shall be finished with PU paint of approved shade. The liquor cupbaord shall be have mirror to internal sides & back with glass shelves & shutters shall have fully glazed bevelled glass shutters in wooden styles finished with decorative carved moulding. The wooden and exposed member shall be finishing with melamine polish & essential fixtures, hardware & fastenening in brass including locking arrangement etc. completed as per Architect's drawings and instructions of Engineer in Charge.

Per One No.

Per One Square foot

Per One Kilogram

Supplying and erecting LED square/circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED Strip light 5m Length Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50, including driver with 1 year warrenty.

Supplying LED concealed type foot/step light with aluminium body for indoor/outdoor application suitable for 4W-6W LED including driver and erecting by making necessary arrangement / recess in wall to make it flush with surface with 1 year warrenty.