Civil works in SARAS building GF and FF at ASERDC at HAL Factory Lucknow

Dismantling/ Demolishing cement concrete floor, Kota Stone, RCC , PCC etc. all Complete and disposal of material within 50 metres lead as per direction of Engineer- in-charge.:Nominal concrete 1:3:6 or richer mix (including equivalent design mix) stacking serviceable and unserviceable material separately including cutting reinforcement bars including cleaning, cost of all labours, scaffolding, transportation, load/ unloading, T & P etc. all complete at all height as per specification and as directed by Engineer in charge.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m; All kinds of soil, complete for foundations, column footing, wall foundation, manholes, post holes, trenches etc. returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm. dewatering if requried, dressing the sides, dispoal of exess surplus soil etc including all labour T&P, lead etc. all complete as per specification, drawing and as directed by Engineer in charge.

Providing & laying PCC: 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) in foundation, under floors or any other similar description of works eg. drains, pipe lines bedding layers, road, chambers etc with mechanical mixing including form work, side shuttering, compaction, curing including , materials, labour, T&P etc, required for proper completion of the work all complete all as per specifications, drawings and as directed by Engineer-in-Charge (EIC).

Providing and laying Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in substructure /superstructure above plinth level up to floor V level, in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) or any description of similar works, including necessary cutting of bricks as required , wastages, straight or curved, work up to any height or depth, including , materials, labour, T&P etc, required for proper completion of the work etc all complete all as per specifications, drawings and as directed by Engineer-in-Charge (EIC).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to & above plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in Foundations, drain, floor, pavement, manhole, approach or any other similar description of works etc including mechanical/ manual mixing, necessary form work, shuttering, compaction, curing including labour, material, T&P etc. all complete all as per specifications, drawings and as directed by Engineer-in-Charge (EIC).

Providing, fabricating and Fixing steel reinforcement, conforming to IS-1786-1985, for any diameter of TISCON / SAIL/ RINL/Gallent advance of approved make by EIC for all type of R.C.C works, using deformed Thermo mechanically treated bars of Fe 500 D or more and conforming to relevant IS of any diameter for all type of R.C.C. works, straightening, cut to length, welding, bend to shape required including cranking bending spirally or hooping providing spacers/ chairs, and binding with mild steel wires (annealed) not less than 0.90 mm diameter so that placing and ramming of concrete will not displace it, including cost of all labours, materials, T & P etc. all complete at all height and location as per specification, drawing and as directed by Engineer in charge.

Providing, rendering, dubbing out cement plastering 15 mm thick with cement mortar 1:6 (1 cement: 6 coarse sand) on walls of rough / fair faces of brick wall / concerete surface including jams, soffit and edges of plastering chamfering wherever required, finishing of surface even and smooth without using extra cement with all labour, material, scaffolding, curing, including hacking of concrete surfaces, T&P etc all complete as per direction of EIC.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of size 450x350mm / 350 x 250 or larger size of kajaria / johnson/ nitco/ orient-bell or as approved make shades, pattern and print / design on walls, in all colours, shades of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead 50 metres lead including cost of all labours, materials, scaffolding and curing and T&P etc. all complete at all height as per specification, drawing and as directed by Engineer in charge.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Providing and applying 01mm thick wall care putty(birla , JK or as approved ) on wall and ceiling for making surface smooth & even including preparation of surface by sand paper, wire brushing, washing down, filling holes, removal of nails etc including scaffolding, wastages, cleaning the surface clean etc.all complete as per direction by E.I.C.

Providing & applying two coats of finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives; New/old work (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.of first quality of approved shade and make like apex ultima of Asian /weather coat long life of Berger / weather shield max of ICI etc including preparation of surfaces, by brooming down, removal of flakes, oil,grease marks by sand papering where required, filling holes /Cracks with birla putty / snowfilla, spreading and removing covering to doors, windows, fittings, floor, etc. to protect from splashes, removing & replacing moveable furnitures, leaving the premises clean and tidy, disposingRubbish outside in dustbins removal of all splashes and cleaning glass and joinery, use of scaffolding all complete as per specification & direction ofEIC.

Providing & applying two coats of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved make & shade such as Asian/Berger/ICI to walls of any description at any height / depth nd of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litreincluding preparation of surface by sand papering, filling holes, cracks with birla putty stopping ,removing oil/smudge marks spreading and removing coverings, to doors, windows, floors,fittings, etc. to protect from splashes, removing and replacing furniture's, moveable cupboards,chicks, blinds, etc. washing floors, cleaning glass,joinery, leaving the premises clean neat and tidy including disposing rubbish outside in dustbins all complete as per specification & direction of EIC

Providing and applying two coats first qulaity of synthetic enamel paint and one coat of suitable primer of Ist quality of Berger/ Asian/ ICI paints of approved brand conforming to relevant IS on all surfaces, new / old, including providing and applying suitable primer, surface preparation, including cleaning the dirt and other impurities, scrapping smooth and filling crevices with approved filler of approved brand, including cost of all material, labours,ladders/ scaffoldings, brushes, T&P etc. complete at all height as per specification, drawing and as directed by Engineer in charge.

Providing, Fabricating & fixing of Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer for MS Roof Truss (framed), Trussed, purlins, crain, gantries, rails & fastnings and heavy bracket framing (beam, Tee, angle, channel, tubular , rectangular, square, flat etc all required sections including distance pieces, cleats, base plates, nut bolts, tie road,foundation bolt etc. at any height including all labour material, T & P, errection, scaffolding, wastage etc.all complete as per specification and direction of E.I.C.

Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of 0.56 mm thick alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately).

Providing and fixing ISI marked flush door shutters to door frame (MS/ Wooden) 30 mm thick phenol formaldehyde bonded, core of block board construction conforming to IS : 2202 (Part I) of make Gee doors/Kit ply/ Swastik or other approved make, non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges 125mm size with necessary screws all complete as per drawings & specification also provisions for door fittings, making holes/ cutting for fixing fittings, making good including labour, material, T&P, cartage, wastage etc all complete as per direction of EIC.

Providing and fixing powder coated aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200 mm x 10mm, including , materials, labour, T&P etc, required for proper completion of the work etc all complete all as per specifications, drawings and as directed by Engineer-in-Charge

Providing and fixing powder coated aluminium 300 x 16 mm sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing powder coated aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm

Providing and fixing twin rubber stopper aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing powder coated aluminium aluminium work for-fixed portion for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, dash fasterners all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) :

Providing and fixing powder coated aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling to be paid for separately ------ for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the costof EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. of make Saint Gobain/ Modiguard or as approved by EIC, complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm) including cutting to shape, fixing, making holes for fittings if required, with all complete including cost of all materials , labours, T & P, cutting wastages, making provisions for harware fittings, etc all complete at all height as per drawing, specification and as per direction of E.I.C. The pattern, desing, colour etc shall be approved by EIC.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead and depositing to Civil Factory store : Of area 3 sq. metres and below including cost of all materials, labours, scaffoldings, T & P, wastages, cutting as per requriement etc. complete at all height as per specification, drawing and as directed by E.I.C.

Supplying and fixing of 04mm thick ACP sheet in Al partition, Al doors, window etc of make Alstone/ Alkor/ Aludecor/ Alstrong or as approved by EIC, finest quality two layers of aluminium skins.Pre eeoated and thermally bonded with non-toxic polyethylene core, fire resistant,Interior grade, dust and corrosion resistant, skin thickness 0.25mm to 0.50mm with tolerence in width & length as +/- 02mm and in thickness as +/- 0.2mm or as per manufacturer including all cutting as per site requirement, fixing with all other material, T & P, labour, cutting, wastage, cartage all complete as per specification and direction of EIC.

Providing and laying Vitrified tiles in floor (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size (600x600) or larger as required at site and approved by EIC.

Providing and fixing Vertical venetian blinds of 75/ 100mm width of approved colour & texture/pattern ( approved designs printed / plain) including its hardware mechanism of repuated manufacturer such as Vista, Aerolux , MAC or as approved all complete with material , fixing, fixing accessories, making holes in concrete / brick wall, making good, wastage etc. including cost of all materials , labours, T & P, cutting wastages, making provisions for harware fittings, etc all complete at all height as per drawing, specification and as per direction of E.I.C. The pattern, desing, colour etc shall be approved by EIC. (sample is to be approved before procurment from reputed manufacturer.)

Providing and laying 02mm thick heavy duty homoeneous , heavy duty, industrial use ans fiexible Non directional, muiti - colour polymer chips, PUR surface protection , homogeneous flooring rolls in width of 2mtr and continuous length of 20mtrs laid in floors/ skirtings in approved design and shade, as per the design of approved make such as adventus series of wonder floor/ Armstrong/ Responsive SPICS RQ brand/ Tuskar as approved by EIC conforming to IS Standards in roll form with suitable adhesive and joints thermo welded to form seam less surface, including removing of existing PVC/ESD/ or any other description flooring and deposited the same as directed lace, cleaning of surface and preparation of surface to receive the floor, filing of minor pits / holes if any with Birlaputty/cement mortar etc. including cost of all material , labour,cutting wastages, T&P etc, complete all as required and directed by EIC.

Dismantling old plaster or skirting of any description at any height raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead including cost of all labours, materials, scaffolding and curing and T&P etc. all complete at all height as per specification, drawing and as directed by Engineer in charge.

Providing and fixing double action heavy duty hydraulic floor spring of approved brand like Godrej/ Aman/Sindhu etc. and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.:With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing designer film of make Gannan/ Orchid/ as approved by EIC of required pattern, self adhesive type fixed on the glasses of doors and windows including cleaning of surface and preparation of surface to receive the film including cutting to required shape and size, laying properly to avoid any air bubble, leaving the suface neet and clean, at all height, scaffolding etc. with cost of all material , labour, cutting, wastages, T&P etc, complete all as required and directed by EIC.

Providing and fixing anodised aluminium grill (poweder coated or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Above

HAL-AD/9904/4654/CE/2024

Civil works in SARAS building GF and FF at ASERDC at HAL Factory Lucknow

Description

Name of the Individual / Firm / Company: * Mandatory

Type of ownership Pvt. Ltd./ Proprietorship/Partnership/ Public limited/ Govt. Agencies/ Trust

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address for correspondence:

Contact details

Intending parties having credentials as mentioned below may participate in e-tendering. The pre-qualification requirements for the works are as under :-

List of similar works executed in the past 7 years with value, schedule period of completion reasons for delay in completion if any and salient features of works, with documentary evidence of satisfactory completion.

PAN No.:

Constitution and legal status i.e. Proof of proprietary/Partnership firm or company & authorised person for receiving or signing the documents to be submitted.

Goods and Service Tax ID No.

SAC (Service Accounting code) for the said work shall be 995419

Bank account details such as account no., name of account holder, name and address of the bank, IFSC code duly certified by the bank along with cancelled cheque as a document of proof shall be attached.

Registered Contractor

Average annual financial turn over during the last 3 years, ending 31st March 2022 of the previous financial year [ should not be less than 30% of Amount put to tender]

EMD of Rs.58180.00

Latest Solvency Certificate issued from Nationalized/ scheduled Bank issued and NOT before 12 months from the last date of Tender submission

Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded]

(i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost.

(ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost.

(iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Details of person holding the power of Attorney (If different from contact person)

DECLARATION I

DECLARATION II

DECLARATION III