SPECIAL REPAIR TO BLDG NO. P-04 AT JDC, BLOCK NO 21 AND 23 AT PEERU VIHAR AND CERTAIN MINOR WORKS UNDER GE SATWARI

Amount

Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster / demolition of cement concrete any thickness and removal of debris off the premises complete all as specified and as directed by Engineer-In-Charge.

Taking up or down steel tubing of 15 mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed by Engineer-In-Charge.

Taking up or down steel tubing of 20 mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed by Engineer-In-Charge.

Taking down chowkats or frames with shutter (with out taking off shutter from the frame) n exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge.

Taking down chowkats or frames with shutter (with out taking off shutter from the frame) exc 1.5 sqm & n. exe 4 sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge.

Taking down cement plaster of any description on brick wall including racking out joints, hacking for key, scrubbing down with water and removing all the demolished material outside cantt area complete all as specified and as directed.

Demolition of Cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) and removing all the demolished material outside cantt area

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises.

Demolition of brick work built in cement mortar including all quoin, arches pillars but excluding aslar facing dressed stone work and precast concrete article complete all as directed.

Dismantling water tanks and removing to store of water storage tanks (cap 500 ltr to 1000 ltr) complete all as specified and directed by Engineer-in-charge.

Taking down CI/PVC pipes 100 mm dia incl all fittings like bend, branch pieces, connectors, heel rest bend etc all as specified and directed.

Taking down CI/PVC pipes 75 mm dia incl all fittings like bend, branch pieces, connectors, heel rest bend etc all as specified and directed.

Taking down shutter of any description exc 1.0 sqm but n. exc 2 sqm each all as specified and directed By Engr-in-charge.

Taking down shutter of any description exc 2 sqm each all as specified and directed By Engr-in-charge.

Demolition of reinforced cement concrete of any description ground to 4th floors and removing unserviceable material exc 100 mtr complete as specified.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) cpmplete all as specified.

Taking down fan,sealing cable end, dismantling blades and depositing fan and blades to MES store.

Cutting chases, pinning in. making good to facings in brick walls where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by Engineer-In-Charge.

Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and as directed by Engineer-In-Charge.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) triple layered,white,hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe and 20 mm dia galvanised iron pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings , including making connections complete all as specified.

Supply and fixing in repair Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) triple layered,white,hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe and 20 mm dia galvanised iron pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, including making connections complete all as specified.

Supply and fixing tubes, 'medium grade' galvanised, 15mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing tubes, 'medium grade' galvanised, 20mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-In-Charge.

Refixing old steel tubing galvanised, 15 mm bore, with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts and connections in new or old position (walls, ceiling, floors, etc.), complete all as specified and as directed by Engineer-In-Charge.

Refixing old steel tubing galvanised, 20 mm bore, with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts and connections in new or old position (walls, ceiling, floors, etc.), complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing sinks made of stainless steel l mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete with waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge. Make: Prayag, CERA,Nirali, Jayna

PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets,PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repair, complete all as specified and as directed by Engineer-In-Charge.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

Vitreous China wash basin, white, corner type, size 400x400X125 mm including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia, waste coupling of chromium plated brass, complete all as specified and as directed by Engineer-In-Charge.Make : Cera,Essco,Hindware ( sample as approved & kept in GE's sample room)

Supply and fixing in repair central hole basin mixer without popup waste system with 450mm long braided hoses, cast copper alloy, chromium plated fency type, complete all as specified. Make:- Jaquar, Cat No- CQT-CHR-23167B.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe,Supply and fixed in repair, complete all as specified and as directed by Engineer-In-Charge..

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 25 mm bore pipe in repairs, complete all as specified and as directed by Engineer-In-Charge.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 20 mm bore pipe in repairs, complete all as specified and as directed by Engineer-In-Charge.

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm- 2 1 0 gms screwed both ends for iron pipe or for unions and fixed for 20 mm bore pipe in repairs, complete all as specified and as directed by Engineer-In-Charge.Make: Prayag, Jainko

Supply and fixing plate racks made of stainless steel l mm thick including fixing cantilever brackets overall size 750mm x 750mm x 250mm complete all as specified and directed by Engineer-in-charge. Make: Prayag, CERA,Nirali, Jayna

Supply and fixing in repair chromium plated Shower rose 125 mm dia overhead with 225 mm with flange size including fixing to steel pipe, complete all as specified.

Supply and fixing in repair Cast iron,100 mm internal bore,sand cast type, soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall.

Supply and fixing in repair Cast iron,75 mm internal bore,sand cast type, soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall.

Supply and fixing in repair Cast iron,50 mm internal bore,sand cast type, soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls

Supply and fixing in repair, 75mm Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair Cast iron cowls, suitable to fix in 50 mm dia pipe complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair Cast iron Reducer 100 to 50 mm internal bore, sand cast type complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair cast iron Bends, 100 mm bore, diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-In-Charge.

Supply and fixing in repair cast iron Bends, 75 mm bore, diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-In-Charge.

Supply and fixing in repair 100 mm bore, Branch pieces, single Tee (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches , including oval access door complete all as specified and directed.

Supply and fixing in repair 100 mm bore, Branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches , including oval access door complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls, & applying two coats of oil bound distemper over two coat of wall care putty of 2 mm thick and one coat of primer complete all as specified.

Prelaminated MDF board 19 mm thick as in shutters / shelves , exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including lipping ( 15 mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all as specified and as directed by Engineer-In-Charge

Material and labour of Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6mtr mean radius built in CM 1:4 complete all as directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan any radius half brick thick wall built in CM (1:4) complete all as directed.

Material and labour for hardcore of broken stone , gauge not exc 63mm deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface, all as specified.

Supply and fixing in repair stainless steel gratings of outer frame dia 100 mm openable type incl all necessary fittings such as hinges including embeding in tiles with white cement.

Supply and fixing in repair PVC square gratings of outer frame size 150 mm incl all necessary fittings including embeding in tiles with white cement Prayag Cat No 115 or equivalent in Hindware,Somany,CERA,Jaquar

Applying roof treatment as below:-- (i) Applying 1st coat of bitumen primer membrane 0.4ltr/sqm by the same membrane manufacturer of density at 25 degree C’ 0.87-0.89Kg/Litre and viscosity 70-160 CPS till the surface properly impregnates and insolvent oil primer evaporates completely (ii) Applying 2nd course of a coat of blown type bitumen of grade 85/25 heated to a temperature of 180 degree centigrade and applying @ 1.2 kg/sqm completely (iii) Applying 3rd course of Polymeric Polypropylene polymer membrane “APP” (Atactic poly propylene polymer ) modified prefabricated five layer 3mm thick not less than 3.6 Kg/Sqm with 160 grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 overlap in length using butane torch with 10cm over laps which shall be thermo fused by flame (iv) Applying course of two coats of aluminium paint over the APP membrane all as specified. All joints and change in direction shall be covered with cement mortar 1:3 mixed with SBR latex @ 200 ml/bag of cement and curved before laying membrane MAKE-IWL/Pidilite Note : Ponding shall be done over RCC slab by filling water which shall be kept for 48 hours.In case a slightest indication of seepage / leakage is noticed the same shall be rectified by grouting the affected portion at no extra cost.Thereafter ponding test shall be repeated till there is no indication of seepage /leakage before application of roof treatment.A proper record of ponding test of RCC slabs shall be maintained by Engr in Charge.The arrangement of ponding test shall be made by the contractor and shall be included in the quoted rates..

Applying Polymeric Polypropylene polymer membrane “APP” (Atactic poly propylene polymer ) modified prefabricated five layer 3mm thick not less than 3 Kg/Sqm on prepared surface of sunken floor/roof including a coat of bitumen primer membrane 0.5ltr/sqm by the same membrane manufacturer of density at 25 degree C’ 0.87-0.89Kg/Liter and viscosity 70-160 CPS, applying a coat of bitumen 85/25 grade @ 1.2 Kg/Sqm of surface and then laying APP membrane using butane torch with 10cm over laps which shall be thermo fused by flame and over the APP membrane and then Applying a coat of bitumen 85/25 @ 1.2 Kg/Sqm over the APP membrane all as specified. MAKE-IWL/Pidilite

M&L for plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation fillings and mass concrete for poles/posts, complete all as specified and directed.

Material and labour for PCC 1:2:4 type B 1 using (20 mm graded aggregate) as in blocks for hold fasts, benching, coping, apex stones, bed plates,manhole covers and the like including weathering slightly rounded or chamfered angles and throating all as specified and direct. Note: Form work required for these items included in the unit rate of this item.

Plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in padding over roof finished and laid to required slope, complete all as specified and as directed by Engineer-In-Charge.

Material and labour for cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) in cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like incl weathering slightly rounded our chamfered angles and threading complete all as specified and directed.

Plain cement concrete 1:5:10, type E-2 (using 40mm graded crushed stone aggregate), as in sunken floors ( upto 4th floor) mass concrete in foundation, complete all as specified and as directed by Engineer-In-Charge.

Supply only Integral water proofing compound, complete all as specified and as directed by Engineer-In-Charge.

Machine cut kota stone slab,single piece slab in staircase,landing,treads etc and flooring (minimum size shall be 550x550mm), flooring 18-20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete, laid over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.Note Length of kota slab not less than width of stair)

Machine cut kota stone 18-20 mm thick in risers,skirting etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete, , set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles over and including 10mm thick rendering in cement mortar 1:4, as in verticle surfaces complete all as specified and as directed by Engineer-In-Charge.

TMT bars 6 to 8 mm and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

TMT bars 10 mm and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

Plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate), 75 mm thick, as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all as specified and as directed by Engineer-In-Charge.

Material and labour for PCC 1:2:4, 25mm thick type B-0 using 12.5mm crushed stone aggregated as in floor finished even and rough all as per specified and directed.

Material and labour RCC type B1, 1:2:4 using 20 mm graded aggregate as in fins,facia,louvers,parapets,Slab supported with wall, beam, column in floor, roof, landing etc including necessary formwork.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

Use and waste formwork to faces of walls,retaining walls, abutments,parapets and staircase railings and similar work including attached pillasters, buttresses,etc.; vertical or to batter for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing pressed steel frames( factory made) made of cold rolled mild steel sheets of 1.25mm thickness as indicated in IS for door with one or more rebates incl lugs, hold fast, lock strike plate etc complete of size 105 x 60mm including one coat of red oxide primer and PCC 1:3:6 as in back fill to chowkats all as spfd.

Supply and fixing in repairs Pressed steel frame (factory made) of size 125x60mm for doors with double rebated including mild steel hinges medium weight 100 mm long and 25x3 mm flat iron in holdfast, tie bar including necessary fixing lugs, lock strike plate and fixing arrangement etc., complete as specified, supplied and fixed including back filling of chowkats in PCC 1:3:6 and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as spd and as directed.

Supply and fixing pressed steel cup board frame made to size from MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:3:6 as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately.

Material and labour 35 mm thick 2nd class hard wood plain framed panelled shutter (two panels) of factory made with lock rail and panel of 12 mm thick veneered particle board with commercial vace veneering on both faces including wooden beads on both sides, one coat of pink primer. The size of rail and stile as per IS-1003 part-I kiln seasoned and chemically pressure treated complete all as directed.

Material and labour 35 mm thick 2nd class hard wood partly panelled and partly guaged and skelton shutter of factory made with lock rail and panel of 12 mm thick veneered particle board with commercial vace veneering on both faces including wooden beads on both sides, one coat of pink primer. The size of rail and stile as per IS-1003 part-I kiln seasoned and chemically pressure treated complete all as directed.

Material & labour flush shutters,factory made both side commercial face door shutter 35 mm thick solid core construction, with block board core and plywood face panels commercial type on both sides complete all as specified and as directed by Engr-in-Charge.Make Archidply,Centuryply,Greenply

Material & labour flush shutters,factory made both side commercial face door shutter 25 mm thick solid core construction, with block board core and plywood face panels commercial type on both sides complete all as specified and as directed by Engr-in-Charge.Make Archidply,Centuryply,Greenply

Supply and fixing 35 mm thick glazed and skeleton shutters 2nd class hardwood as in windows, ventilators etc, open rebated and prepared to receive glass, gauze etc (with sash bars) edges of framing plain, chamfered or roundedfitted with cut and mitred beads for scuring glass, etc size of members of shutters as specified in SSR-I, section 8, clause 8.24 (a) fixed to chowkhats complete all as directed.

Supply and fixing in repair Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified and as directed by Engineer-In-Charge.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing aluminium handles, cast type, anodised, size 100 mm, complete all as specified and as directed by Engineer-In-Charge

Supply and fixing Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 of size 100 mm.(ISI marked) complete all as directed.

Supply and fixing butt hinges of mild steel cold rolled medium weight of size 75 mm as specified.

Supply and fixing mild steel helical/ordinary rat tail rod pattern door spring 225 mm including roller and roller plate complete fixed with welding all as specified. (ISI Marked)

Supply and fixing Aluminium anodised, barrel tower bolts size 200 mm of extruded section and fixed complete all as specified. (ISI Marked)

Supply and fixing aluminium anodized door handle size 150mm size of extruded section complete all as specified and directed.

Supply and fixing Floor door stopper of stainless steel body size 140 mm (Overall length of cover plate) and tongue, anodised, with hard drawn steel spring, fixed in floor.Make Prayag Cat part no 5121.

Supply and fixing magnetic door catcher of stainless steel body.Make Prayag Cat part no 5124 complete all as specified and directed.

Supply and fixing in repair magnetic door catcher for cupboard shutters of stainless steel body complete all as specified and directed.

Supply and fixing in repair continuous (piano) hinges, heavy duty mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified. ( ISI Marked)

Material & labour Aluminum Powder coated frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc(minimum thickness of powder coating 50 micron) complete all as specified. Make Jindal/Hindalco

Material & labour Aluminum Powder coated, window and ventilator sliding shutters without sash bars, three track with mosquito proofing with style 44.4x44.5x2mm thick including 5.50 mm thick coloured/tinted glass panes and all necessary fittings and fixtures complete all as per Engr-in-charge.

Material & labour Aluminum Powder coated grills fixed to sliding aluminium windows with all fixing arrangement,grill apperture 100x100 mm 6 mm dia thick minimum weight of grill 2.25 kg/sqm including all necessary fittings and fixtures complete all as per Engr-in-charge.

Material & labour factory made steel windows double shutter box type, outer frame made out of ERW TUBE 'P' section(65x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung including pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars dovetailed or welded ready for glass fixing and wire gauzed fixing with suitable fittings/opening for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specified and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) for Provn of one shop coat of zinc chromate primer on all exposed steel surfaces and one coat of coal tar on the ends of steel frame in contact with brick/conc surface (ii) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (iii) PCC block for embedding lugs.

Supply and fixing Aluminium alloy, anodised, sliding door bolt size 250mm (length of bolt) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete al as specified. (ISI Marked)

Supply and fixing in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, provide 10 numbers stainless steel wings with 50 mm dia and proportionate for part there off, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

Supply and fixing Mild steel works of flat iron, square bar, round bars etc. as in framed work such as hold fast,stack clamp,grills, guard bars, gratings etc incl bending, cutting and welding as necessary of confirming to Gde Fe 310-0 all as specified.

Supply and fixing Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.8mm and fixed with stainless steel wire staples

Rendering 15 mm thick on brick work or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement on walls/floors including mixing of water proofing compound complete all as specified and as directed by Engineer-In-Charge. (WPC shall be measured and paid for separately)

Material and labour for rendering 15 mm thick in CM 1:3 on fair faces of concrete surfaces in sunken floors finished even and smooth without using extra cement all as specified including mixing of water proofing compound complete all as specified and directed. (Water proofing compound shall be measured and paid separately)

Material and labour for rendering 5mm thick on concrete surfaces as in ceiling,columns,RCC walls,fins in cement mortar 1:4 finished even and smooth without using extra cement..

Material and labour Rendering 15mm thick in CM 1:6 on fair brick wall surface or concrete surface finished even and smooth without using extra cement,complete all as specified.

Material and labour Rendering 15mm thick in CM 1:4 on fair brick wall surface or concrete surface finished even and smooth without using extra cement,complete all as specified.

Material and labour for rendering 15 mm thick in CM 1:6 on other than fair face of brick work/ stone wall surfaces finished even and smooth without using extra cement all as specified.(including all scaffolding,lifting arrangement for three story building on exteral surfaces)

Material and labour for repairing of concrete surfaces such as chajjas,upward facia,downward facias,ceiling and similar items with plain cement concret 1:2:4 type B-0 or rendering 10mm thick in CM 1:3 includind dubbing coat without using extra cement finished even and fair including necessory formwork and scaffolding complete all as specified and directed.(Up to fourth storey bldg)

Material and labour for preparation of surface, free from dirt, dust & loose particles, thoroughly wire brushed & cleaned by vacuum cleaner. Washing the surface with water, removing of all oil & grease substance using degreasing solvents. Any damaged surface must be repaired by using polymer modified repair mortar with Dr. Fixit Pidicrete URP. Thereafter clean the surface saturated with water and remove the excess water, if any, and bring to touch dry state. Apply the first coat of the mixed solution @ 0.75 Sqm/Kg, (1 mm thick for 2 coats) Dr Fixit Pidifin 2K on the prepared surface & allow to dry for 4 to 6 hours. Prepare another batch of Dr Fixit Pidifin 2K and apply 2nd coat in direction 90 degree to first coat. Over it lay a protected screed, using cement sand 1:3 along with Dr Fixit LW+ complete all as specified and as per the manufacture instructions.

Material and labour Non - skid digital,anti scratch,anti fungus,Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match the surface over and including 15mm thick screed bed in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

Material and labour Non - skid digital,anti scratch,anti fungus,Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match the surface over and including 15mm thick screed bed in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

Material and labour for glazed,Ceramic joint free coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match the surface over and including 10mm thick rendering in C:M 1:4. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

Material and labour glazed digital ceramic tiles in vertical surface of size 450x300x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over and including 10 mm thick rendering in CM 1:4 all as specified. Make : Somany,Kajaria,Orient ( sample as approved & kept in GE's sample room)

Material and labour 18 to 20 mm thick Granite Zed black (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 as directed by Engr-in-charge.

Material and labour 18 to 20 mm thick Green marble (of any type) tiles machine cut,bedded and jointed with grey cement slurry and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 20 mm thick screed bed in CM 1:4 as directed by Engr-in-charge.

Material and labour Vitrified Ceramic (double charged) any shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in C:M 1:4. Make : Somany,Kajaria ( sample as approved & kept in GE's sample room)

Description all as item no 114 but as in verical surfaces such as dado/skirting over and including backing coat of CM 1:4,10 mm thick complete etc.

Preparation of new plastered surfaces of wall and applying two coat of cement base paint including a base coat of primer surface complete all as spd

Preparation of old decorated brick /concrete/ plastered /un-plastered surfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots,rubbing with sand paper and applying two coat of oil bound distemper on walls, pillars, cornices surface including making good uneven surface/holes with 2 mm Birla wall care putty coloured in same shade etc. complete all as specified and directed.

Preparation of old decorated plastered /concrete/ brick surfaces of walls (up to 4th storey with necessary scaffolding) and applying two coat of cement based paint on old decorated surfaces complete all as specified and directed.

Material and labour for applying two coat of synthetic enamel paint on new steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper or grinding by hand grinder to make surface even and smoth and applying primer where required (up tp 4th storey with necessary scaffolding) complete all as specified and directed.

Material and labour for applying one coat of synthetic enamel paint on old painted steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth and apply putty and primer where requred complete all as specified.

Material and labour for applying one coat of synthetic enamel paint on old painted wood surfaces of any description having width/girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth.

Material and labour for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width/girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth.

Material and labour for preparation of old decorative plastered/concrete surface of wall, chajja, facia, face of columns, beam etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying one coat of weather proof exterior emulsion (APEX) with necessary scaffolding including necessary filling of wall care putty 3 mm thick on uneven surface as and where required all as specified.

Material and labour for preparation of new decorated/ plastered/concrete surface of wall, chajja, facia, face of columns, beam etc and applying two coats of weather proof exterior emulsion (APEX) over one coat of primer with necessary scaffolding including necessary filling of wall care putty 3 mm thick on uneven surface as and where required all as specified

Preparation of old decorated brick /concrete/ plastered /un-plastered surfaces of ceilings, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots,rubbing with sand paper and applying one coat of white wash on ceiling complete all as specified and directed.

Preparation of old decorated brick /concrete/ plastered /un-plastered surfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots,rubbing with sand paper and applying two coats of lime white wash on walls, pillars, cornices etc. complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceilings to achieve smooth and even surface and applying three coats of white washing complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair Wall Mixer with Provision for overhead Shower with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges complete al as specified. Make:- Jaquar, Cat No- CQT-CHR-23273UPR or equivalent in Kohler.

Supply and fixing in repair sink mixer with swinging cast round shape spout ( wall mounted model) with Connecting Legs & Wall Flanges complete all as specified. Make:- Jaquar, Cat No- CQT-CHR-23309 or equivalent in Kohler.

Supply and fixing in repair chromium plated Bib Cock cast copper alloy, chromium plated fancy type screwed for iron pipe, 15 mm bore complete all as specified. Make :- Jaquar, Cat No- CQT-CHR-23037 or equivalent in Kohler

Supply and fixing in repair angular stop cock , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified. Make:- Jaquar, Cat No:- CQT-CHR-23053 or equivalent in Kohler.

Angle valves cast copper alloy, chromium plated with long shank and cup (concealed type)with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair 450mm Long Braided Hose with Two 15mm Nuts & Rubber Washers (Both Side) Without Nipple (Suitable for Geysers) complete all as specified. Make :- Jaquar, Cat No- ALD-CHR-805B or equivalent in Kohler

Supply and fixing in repair 450 mm long braided hose with M10x1 nipple, 15 mm nut,O-ring and rubber washer (suitable for Basin Mixers) complete all as specified. Make:- Jaquar, Cat No:- ALD-CHR-803AB or equivalent in Kohler

Supply and fixing in repair Vitreous china wash down water closet white, Size(365x540x400mm) with 'S' trap, including soft closing seat cover , closed pattern with flat bottom, complete all as directed. Make:- ESSCO Cat Part No- ECS-WHT-551SS. or equivalent in Cera

Supply and fixing in repairs CP brass jet spray with flexible pipe n.less than 90 cm long fixed to EWC suitable for 15mm bore complete all as specified and directed at site Make Jaquar CAT No ALE-547 Jet spray with 1 Meter PVC tube (SS) or Kohler

Supply and fixing in repair Concealed Stop Cock Regular Body Suitable for 15mm Pipe Line with Spindle Extension & Plastic Protection Cap (without Exposed Parts), complete all as specified. Make:- Jaquar, Cat No:- ALD-CHR-083CQT. or equivalent in Kohler

S&F in repair Exposed Part Kit of Concealed Stop Cock & Flush Cock with Fitting Sleeve, Operating Lever & Adjustable Wall Flange with Seal (compatible with ALD-083, ALD-089 & ALD-081) complete all as specified. Make:- Jaquar, Cat No:- OPP-15083KPM. or equivalent in Kohler

Supply and fixing in repair 2 way angular cock cast copper alloy, chromium plated sutable for 15 mm GI pipe, complete all as specified. Make :- ESSCO something special series or equivalent in Cera

Supply and fixing in repair 2 way angular cock cast copper alloy, chromium plated sutable for 15 mm GI pipe, complete all as specified. Make :- ESSCO something special series or equivalent in Cera

Supply and fixing in repair Corner Glass Shelf (with Bracket) as per directed by Engr-in-charge. Make:- Jaquar, Cat No- ACN-1173 or equivalent in Kohler

Supply and fixing in repair CP Overhead Shower 120mm dia round shape single flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System,including shower arm minimum length 190 mm complete all as specified. Make :- Jaquar, Cat No- OHS-CHR-1989 or equivalent in Kohler.

Supply and fixing in repair Concealed Stop valves,fancy type ,cast copper alloy,screwed down,high pressure,with long shank and cup,screwed both ends for iron pipe or for unions and fixed complete all as specified.Make -Essco or equivalent in Cera

Supply and fixing in repair chromium plated, single towel rail 600mm long complete all as specified. Make:- Jaquar Cat No- AKP-CHR-35711P or equivalent in Kohler

Supply and fixing in repair chromium plated towel rack 600mm long without lower hangers, complete all as specified. Make :- Jaquar Cat No- AKP-CHR-35781P or equivalent in Kohler

Supply and fixing in repair chromium plated hand shower (health faucet) with 8mm dia 1.20m long flexible tube and wall hook, complete all as specified. Make :- Jainko,Prayag

Supply and fixing in repair Shower Arm Casted 190mm Long Light Body Round Shape for Wall Mounted Showers with Flange complete all as specified. Make :- Jaquar, Cat No- SHA-CHR-477P or equivalent in Kohler

Supply and fixing in repair Overhead Shower 100mm dia round shape single flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning Systemr, complete all as specified. Make :- Jaquar, Cat No- OHS-CHR-1989.

Supply and fixingin repair soap dish holder complete all as specified. Make:- Jainko,Prayag

Supply and fixing in repair chromium plated toilet roll holder, complete all as specified. Make:- Jaquar, Cat No- AKP-CHR-35751P or equivalent in Kohler

Supply and fixing in repair Glass shelf 600mm long, complete all as specified. Make:- Jaquar, Cat No- AKP-CHR-35771P or equivalent in Kohler

Supply and fixing in repair Wall Hung Basin with Fixing Accessories Set, Size : 555 x 425 x 195mm, complete all as specified. Make :- Jaquar, Cat No- CNS-WHT-811 or equivalent in Kohler.

Supply and fixing in repair full pedestal for WHB Cat No- CNS-WHB-811 complete all as specified. Make :- Jaquar, Cat No- CNS-WHT-303 or equivalent in Kohler.

Supply and fixing in repair vitreous china squatting pan Orissa pattern white with PVC(SWR) P or S trap front or back inlet with integral foot rest 585x 445 mm including L bend, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified including in taking out and removal of old WC seat) Make:- Hindware,Parryware,Cera

Supply and fixing in repair Wall Hung Cistern with Drainage L-Bend Pipe with Gasket & Installation Kit (Suitable for EWC), complete all as specified. Make:- Hindware,Parryware,Cera

Supply and fixing tubes, 'heavy grade' galvanised, 40 mm bore, ISI marked and fixed complete to walls and ceilings or laid in floors as spout pipe in sunken floors, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair PVC (SWR) bends any radius 75mm bore Make :- Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) bends any radius 110 mm bore Make :- Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) junction single, (Single T) equal or unequal with oval access door( Grade " B " ) 75 mm bore complete all as specified and as directed by Engineer-In-Charge. Make :- Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) junction single, (Single T) equal or unequal with oval access door( Grade " B " ) 110 mm bore complete all as specified and as directed by Engineer-In-Charge. Make :- Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) reducers( Grade " B " ) 110 mm bore complete all as specified and as directed by Engineer-In-Charge. Make :- Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) pipes ( Grade " B " ) 110 mm bore, single socketed in any length with rubber ring joints and glue fixed to walls .Make Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) pipes ( Grade " B " ) 110 mm bore, single socketed in any length with rubber ring joints and glue laid in trenches .Make Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) pipes ( Grade " B " ) 75 mm bore, single socketed in any length with rubber ring joints and glue fixed to walls .Make Finolex/Kisan/Supreme

Supply and fixing in repair PVC (SWR) pipes ( Grade " B " ) 75 mm bore, single socketed in any length with rubber ring joints and glue laid in trenches .Make Finolex/Kisan/Supreme

Supply and fixing PVC corrugated waste pipe 32mm x 800 mm long for required length complete Make: Prayag Cat No 327 or equivalent in Hindware,Somany,CERA,Jaquar

Supply and fixing PVC corrugated waste pipe 40 mm x 800 mm long for required length complete Make: Prayag Cat No 328 or equivalent in Hindware,Somany,CERA,Jaquar

Supply and fixing PVC (SWR) 'P' trap 100 mm complete all as specified.

Supply and fixing in repair PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.

Supply and fixing in repair PVC (SWR) floor trap 75 mm bore type B , plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing in repair 75 mm bore PVC (SWR) multi floor trap type B , plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-In-Charge.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

Supply and fixing 75 mm bore PVC (SWR) Type B vent cowl complete all as directed.

Supply and fixing UPVC type B pipes 110 mm bore as rain water pipe single socketed in any length with rubber ring joints fixed complete to walls and ceilings or laid in floors,weight of pipe not less than 0.70 kg /mtr (ISI Marked) complete all as specified and as directed by Engineer-In-Charge. NOTE: Work to be carried out up to 4th storey bldgs in any condition of working location/area.

Supply and fixing 4.8 mm thick sheet glass ordinary quality glazing with steel pins,oil putty to steel windows and, beads nails etc to wooden surfaces as in square exc 0.50 sqm in each pane, (up to 4th storey with necessary scaffolding) all as specified.

Supply and fixing 3 mm thick sheet glass ordinary quality glazing with steel pins,oil putty to steel windows and, beads nails etc to wooden surfaces as in square exc 0.50 sqm in each pane, (up to 4th storey with necessary scaffolding) all as specified.

Supply and fixing in repair 3 mm thick sheet glass ordinary quality glazing with steel pins,oil putty to steel windows and, beads nails etc to wooden surfaces as in square exc 0.50 sqm in each pane, (up to 4th storey with necessary scaffolding) all as specified.

Supply and fixing Figured glass, pin head type and glazing with oil putty and clips in squares n exc 0.5 sq.m in each pane of thickness 3mm (up to 4th storey with necessary scaffolding)up to complete all as specified

Supply and fixing Figured glass, pin head type and glazing with oil putty and clips in squares n exc 0.5 sq.m in each pane of thickness 4 mm (up to 4th storey with necessary scaffolding)up to complete all as specified

Material and labour Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

Supply only Water proofing compound liquid.

E/M ITEMS Taking down carefully aluminium conductor point wiring (light, fan, light socket, power socket) complete fitting such as switches, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good disturbed surface of walls and roofs to the existing surface & finish complete all as specified and as directed.

Taking down of UNSV MCB DB along with MCB's complete all as directed.

Material and labour for point wiring one light/fan point controlled by one, one way switch 6 Amp complete with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , terminated into modular galvanised flush boxes of suitable size including white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed.

Description all as per srl item No 185 but one 3 pin socket outlet 6 amp independent board.

Description all as per srl item No 185 but one 3 pin socket outlet 6 amp on same board.

Description all as per srl item No 185 but one bell/buzzer point controlled by one way switch 6 Amps all as specified and directed

Description all as per srl item No 185 but one 2 way light point controlled by two 2 way switch all as specified and directed.

Description all as per srl item No 185 but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for piont wiring and 2.5 sqmm as in continuous earth wire. complete all as specified and directed.

Supply and fixing modular switch Polycarbonate material ISI marked one way, 6 Amps, 240 V Make: Cat Ref 800100 Elvira Indoasian or equivalent in Havells, Legrand.

Supply and fixing modular switch Polycarbonate material ISI marked two way, 6 Amps, 240 V Make: Cat Ref 800101 Elvira Indoasian or equivalent in Havells, Legrand.

Supply and fixing modular socket outlet 6 Amps 3 pin Universal socket complete all as specified and as directed. Make: Cat Ref 800120 Elvira Indoasian or equivalent in Havells, Legrand

Supply and fixing modular switch Polycarbonate material ISI marked one way, 16 Amps, 240 V Make: Cat Ref 800103 Elvira Indoasian or equivalent in Havells, Legrand

Supply and fixing modular socket outlet 2 in 1, 6 / 16 Amps 3 pin socket complete all as specified and as directed having pencil free operation & child safety shutter . Make: Cat Ref 800122 Elvira Indoasian or equivalent in Havells, Legrand

Supply and fix modular fan regulator step type (electronic ) 2 Module for 1200/1400mm sweep AC ceiling fan.Make: Cat Ref 800142 Elvira Indoasian or equivalent in Havells, Legrand

Supply and fixing ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fixing musical door bell, 240 volts complete all as specified and directed.

Supply and fixing Modular Bell push 6A 1 module complete all as specified and directed.

Supply and fixing down rod (hanging rod) made of GI tubing 20mm bore for length upto 60 cm suitable for AC ceiling fan of size 1200mm/1400mm sweep including provision of hole for fixing of nut and bolt all as specified including fan hook and clamps to be fixed in the ceiling made of suitable size flat MS iron complete all as specified and directed.

Supply and fixing LED tubelight fitting 18-20 W LED, 230V, Box type complete in all respect . Cat part No DMLN1LT8-16 of Crompton or equivalent in Havells, Wipro alongwith LED tubeRod with heat dissipation capability suitable for G-13 base tube lights base fluorescent T8/T12 luminaries, 20 watt LED wattage with colour temp of 5700 K 1800 lumens and with surge arrestor complete in all respect. Cat Part No LTT8-20 of Crompton or equivalent in Havells, Wipro. Note:- The LED batten and LED tube rod shall be of same make.

Supply and fixing LED wall mounted batten extruded polycarbonate lighting fixture 10 W LED, 230V complete all as specified and directed.

Supply and fixing complete energy saving new generation 10W LED IP65 bulk head luminary with opal diffuser complete all as specified and directed incl LED 10Watt. Make Havells Cat Part No LHEOAOP7UZ6W010 or equivalent in Wipro, Crompton, Jaquar

Supply and fixing of lamp holder, PVC /Polycarbonate type with back plate for batten fitting with LED bulb 7 Watt.

Supply and fixing LED lamp suitable for B22 holder of capacity 7 watt Make : Havells, Philips, Wipro, Jaquar.

Supply and fixing Distribution Board (SPN) double door 12 Way and should be IP 43 protected with Copper Bus bar, Earth Bar ,neutral Bar Door Earthing .Makes: IndoAsian Optipro Cat Part No 811808 or or equivalent in Havells/ Legrand/C&S

Supply and fixing Distribution Board (SPN) double door 08 Way and should be IP 43 protected with Copper Bus bar, Earth Bar ,neutral Bar Door Earthing .Makes: IndoAsian Optipro Cat Part No 811807 or or equivalent in Havells/ Legrand/C&S

Supply and fixing distribution board (TP&N) double door fitted with Bus bars neutral links blanking plates suitable for 4 pole MCB as incoming and out going MCBs 4 ways and should be IP 43 protected with Copper insulated busbar assembly, Isolated Neutral Bar, Earthig Bar, Door earthing complete all as specified and directed. Make:- Indo Asian Optipro Cat part No 811840 or equivalent in Havells/ C& S electric. Note:- i)Rate includes isolator four pole 63 Amp ii)MCBs shall be measured and paid separately Note : MCB & DB shall have the same make.

Supply and fixing MCB single pole neutral complete 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.Make:- IndoAsian Optipro Cat Part No 811151 or equivalent in Havells/ Legrand/C&S

Supply and fixing MCB four Pole complete 63 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.Make:- IndoAsian Optipro Cat Part No 811242 or equivalent in Havells/ Legrand/C&S

Supply and fixing MCB single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series, ISI Marked complete all as specified and directed. Make:- IndoAsian Optipro or equivalent in Havells/ Legrand/C&S

Supply and fixing in replacement single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 Volts.

Supply and fixing sub main wiring with single core cable 2x 6 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1x6 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chasing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fixing sub main wiring with single core cable 2x 10 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1x10 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chasing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fixing exhaust fan 300 mm sweep, heavy duty, Single phase AC 230/240V, with energy efficient motor, pre lubricated double ball bearing, speed 900 rpm complete with louvers for wall mounting including making hole in the wall,grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan complete all as specified and directed. Make : Havells Cat part No Turbojet SP or equivalent in Crompton./Bajaj Note : Each exhaust fan shall be marked with the MES No in black/white paint clearly visible to naked eye when fitted in position.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide n.exe 1.5m depth in any type of soil for for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of under ground electric cable,pole etc and getting out complete all as directed.

Returning filling in including spreading, leveling watering and well ramming in layers n.exe 25cm thick in any type of soil complete all as specified.

Removal of surplus soil to a distance n.exc 50mtr and depositing at a level n.exc 1.5m above starting point all as directed by Engr-in-Charge.

Supply and fixing in repair Gun-metal, globe or gate valves, 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixedcomplete all as specified. ( ISI Marked)

Supply and fixing AC single phase 240 Volt 50Hz ceiling fan of size 1200mm sweep 5 star rating with canopy and hanging rod with all accessories incl nuts, bolts, clamps etc., complete all as specified and directed. Make : Havells cat part No ES-50 premium 5 star ISI marked, Crompton cat part No : Entrust 50 or Orient cat No Jazz pearl metallic white chrome. Note : Each ceiling fan shall be marked with the MES No in black paint clearly visible to naked eye when fitted in position.

Material and labour for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick buried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinforcement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose to fan after repair work done.

M/S KEWAL MAHAJAN AND CO

M/S Shesh Paul Gupta

M/S K D Construction Co

M/S VIJAY KUMAR SHARMA