Construction of Infrastructure with Prefabricated materials for accommodation of CAPF-50 Coys under SRE NE at 50 locations

Amount

(1) At Gwaltabi, Imphal East District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Gwaltabi, Imphal East District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(2)At Keithelmanbi Outpost, Imphal East District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Keithelmanbi Outpost, Imphal East District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(3) At Chanung(near Unacco), Imphal East District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Chanung(near Unacco), Imphal East District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(4)At Leitanpokpi Sadu Lampak, Imphal East District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Leitanpokpi Sadu Lampak, Imphal East District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(5)At Nungshum awang leikai near handpump, Imphal East District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Nungshum Awang Leikai near hand pump, Imphal East District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(6)At Dolaithabi, Imphal East District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Dolaithabi, Imphal East District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(7) At Machi PS,Tengnoupal District.

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Machi PS, Tengnoupal District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(8) At ADC Complex under Moreh PS,Tengnoupal District.

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at ADC Complex under moreh PS, Tengnoupal District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(9) At Saivom (11-IRB Land),Tengnoupal District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Saivom(11- IRB Land), Tengnoupal District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(10At Pallel PS Campus, Kakching District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Pallel PS Campus, Kakching District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(11)At Khongnang Pheisabi Village under Sugnu PS, Kakching District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Khongnang Pheisabi Village under Sugnu PS, Kakching District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(12)At Sugnu Mamang Leikai Paddy Field under Sugnu PS, Kakching District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Sugnu Mamang Leikai Paddy Field under Sugnu PS, Kakching District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(13)At Serou Ningthem Hiden under Sugnu PS,Kakching District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Serou Ningthem Hiden under Sugnu PS, Kakching District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(14)At Serou awang Leikai, Kakching District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Serou Awang Leikai, Kakching District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(15) At Nongpok Sekmai, Thoubal District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Nongpok Sekmai PS, Thoubal District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(16) At Heirok,Thoubal District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Heirok, Thoubal District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(17) At Saikul PS,Kangpokpi District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

P/F 1 mm thick M.S. sheet doors with frame of 40 X 40 X 6 mm, angle iron and 3 mm M.S. gusset plate at the junction and corners, all necessary fittings complete i/c applying a priming coat of approved steel primer.(a) Using M.S. angles 40 x 40 x 6mm for diagonal braces.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: B-Kitchen cum dining hall and store-1 no.)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (900x2020) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of powder coated extruded Aluminium window frame i/c clear float glass of 4mm thick 2 track sliding shutter of size (800x1035) mm with aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net i/c locking arrangement as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

(SH: C-Toilet block - 8WC-1 unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Proving and fixing UPVC soil,waste ,rain water and vent pipes including all requisite fittings,jointings of pipes & fiitings with solvent cement ,trenching,refilling and testing of joints complete as per direction of engineer in charge. 110mm dia. Pipe

Supplying and Providing of PVC Septic tank(2000 Ltr.) i/c all accessories

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(1no. of 1000 litres capacity )

(SH: D-Toilet block - 6 bath-1 Unit)-1 Unit

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:5:10 (1cem: 5c/sand:10 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).

Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete (b) Thermo-Mechanically Treated bars

Centering and shuttering including strutting, proping etc. and removal of form for(b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick

Brick work with 1st class common burnt clay F.P.S (non modular) brick in foundation and plinth in 1:4(1cem:4 c/sand)

12 mm cement plaster 1:3(1 cement:3 fine sand)finished with a floating coat of neat cement.

Supplying and installing PUF panels of 50mm thick composite PUFsandwich between PPGI sheets ( prepainted galvanized steel sheet ) of thickness 50mm thick layer of rigid CFC free polyurethane foam of density of 40±2 kg/m3 as insulation. the wall panel will have tongue & Groove arrangement and interlocked using cam lock system. PPGI sheet shall have minimum coating of 4-5 micron epoxy primer and 25 micron polyester top coat on the finish surface and 7-8 micron primer alkyl base on reverse. Color shall be preferably RAL 9002 – off white or RAL 5012 – Blue. Panel shall be GRIHA certified with all fittings and accessories complete as per appd design and drawings and s per instruction of the engineer in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick.

Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick.

Supplying, fixing and fitting of door of size (650x2000) mm with MS frame and puff panel shutter with PPGI channel frame i/c all door fittings and accessories as per approved drawing and design and as per instruction of the site engineer etc. complete.

Supplying, fixing and fitting of PPGI frame Ventilator for 450x450mm with PPGI louver shutter and Aluminium grill of 50mm square mesh of 4.5mm dia. along with 1.2mm fibre mosquito net as per approved drawing and design and as per instruction of the site engineer etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. i)15 mm nominal outer dia Pipes

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL PE Composite Pressure Pipes conforming to IS - 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work i ) 2532 (32 mm OD ) pipe

Providing and fixing brass bib cock of approved quality: a) 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shapewith bracket of the same materials with snap fittings of approvedquality and colour, weighing not less than 105 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank-(2nos of 500 litres capacity )

Sh:-Providing IEI for 40 SM barrack - 2nos, Kitchen cum Dining Hall and Store-1no,Toilet Block- 8Wc-1block and Toilet Block -6Bath-1block at Saikul PS, Kangpokpi District

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch, modular plate suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a)Group A

(b)Group B

(c)Group C

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in surface/recessed PVC conduit etc.as reqd.

(a)2X1.5mm2+1X1.5mm2 earth wire

(b)2X2.5mm2+1X2.5mm2 earth wire

(c)2X4mm2+1X4mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd.

(a)5/6 amps switch

(b)15/16 amps switch

(c)3 pin 5/6 amps socket outlet

(d)6 pin 15/16 amps socket outlet

P/L 4mm2 twin core pvc ins.(heavy duty) Cu. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd.

Wiring for submain with 10 mm2 pvc ins.twin core weather proof cable on G.I. bearer wire etc. as reqd.

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb

S/F surface/ pendent mounting 1 x 18 W LED lamp channel luminories complete with all accersories connection etc. as required

S/F fan hook i/c bolt & nuts.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

P/F 60 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way

P/F 30 amp MCSPN switch unit 240/250v with rewireable fuses i/c drilling holes on the board connection, earthing the body etc.as reqd.

S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way single door

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 4 way single door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

(a)10 amp MCB "C" Curve

(b)20 amp MCB "C" Curve

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc.

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Supply & Fixing swaged type steel tubular pole 8 mtr. Long as per 410 SP 14.conforming to IS 2713 (Pt.II) 1980 with bracket in cement concrete 1:3:6 (1:cement:3c/sand:6 gr. st. 40 mm n/size) foundation i/c excavation and refilling etc. as requred.

Supply and drawing of AB Cable of size (3x50 + 1x35) mm2

Cross arm 70X40mm/2 wire.

Back clamp for Cross arm 70X40mm

S/F stay set complete with stay wire & stay insulator etc.as reqd.

(18) At Bethel under Kangchup PS , Kangpokpi District

SH: A-40 SM Barrack with Commander Room- 2 nos

Earth work in excavation by mechanical means(Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or on plan) i/c dressing of sides ramming of bottom lift up to 1.5m i/c getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. in all kinds of soil.

Filling available excavated earth (excluding rock) in trenchs,plinth,sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Supply and filling in plinth with sandy soil under floor i/c watering, ramming, consolidating and dressing complete.

Providing 75mm thick (unconsolidated) of brick aggt. 40mm nominal size well rammed and consolidated i/c preparation of ground.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level (a) 1:4:8 (1cem: 4c/sand:8 graded stone aggregate 40mm nominal size )

(b) 1:2:4 (1cem: 2c/sand:4 graded stone aggregate 20mm nominal size )

Providing & laying in position specified grade of reinforced cement concret, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level (b) 1:1.5:3 (1cement:1.5 :3c/sand : 4 graded stone aggt. 20mm nominal size).