Repair maint, periodical services and rewiring of Main Bldg and Toilet block of ARPS, 25 Assam Rifles at Jalukie.

SCHEDULE ‘A’ PART - I (Repair of Building)

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : Old work (two or more coats) including prepariong surface by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, One or more coats on old work.

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under with cement mortar 1:4 (1 cement : 4 fine sand), including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

Providing and fixing 30 mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing ie steel Hinges, steel tower Bolts and Steel Handles etc complete.

Providing and fixing White Vitreous China Flat back wash basin size 550x 400 mm with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing P.V.C. low level flushing cistern 10 litre capacity - White with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

Providing and fixing P.V.C. waste pipe Semi rigid pipe 32 mm dia for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms for wash basin and sink, of approved quality and colour.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing G.I. 15 mm dia nominal bore pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall

Providing and fixing gun metal gate valve 20 mm nominal bore with C.I. wheel of approved quality (screwed end).

Providing and fixing uplasticised PVC connection pipe with brass unions :60 cm length, 15 mm nominal bore.

Providing and fixing C.P. brass bib cock 15 mm nominal bore of approved quality conforming to IS:8931.

Providing and fixing C.P. brass angle valve 15mm nominal bore for basin mixer and geyser points of approved quality conforming to IS:8931.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required (Group B) as per direction of Engineer in Charge.

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor,single core cable and earthing etc. as required. (Payment of tube to be paid Separately)

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and drawing 2 x 2.5 sq. mm sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

A B S CONSTRUCTION

M/S ZANDI DOMTA