ADDTION AND ALTERATION OF BLDG NO P37 AT ICGS KAVARATTI UNDER GE NAVY LAKSHADWEEP

Amount

Demolition of brickwork, stone / boulder or PCC Block masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed .

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for including cutting of reinforcement, as required to facilitate demolition complete all as specified and as directed .

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc. 15cm thickness (below or above ground level) complete all as specified and as directed

Dismantling of floor, hearth or wall tiling including cement mortar bedding but not backing coat and renmoval of rubbish out side MD land complete all as specified and as directed.

Taking down cement plaster on brick walls or stone walls any descrition etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Taking down old chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each with shutter (without taking off shutters from frame) complete all as specified and directed.

Taking down old chowkhats or frames not exc 1.5 sqm each with shutter (without taking off shutters from frame) complete all as specified and directed.

Pre -cast cement concrete block masonary with solid blocks exc 10 cm in width type C-1 1:3:6 (20mm graded stone aggregate) set in cement mortar 1:6 complete complete all as specified

Pre -cast cement concrete block masonary with solid blocks not exc 10 cm in width type C-1 1:3:6 (20mm graded stone aggregate) set in cement mortar 1:4 complete all as specified and as directed

Use and wast of formwork to soffits of floor or roof beams, beam haunchings, girders, bressumers , lintels, cantilevers, shelves including supports, overhangs etc., also splays between floors and beams complete all as specified and as directed .

RCC 1:1.5:3 Type A1 nominal mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

Use and wast of formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed .

RCC 1:1.5:3 Type A1 nominal mix using 20 mm graded stone aggregate as in chajjas etc complete all as specified and as directed.

Mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

Mild steel CRS TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

Mild steel CRS TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed complete all as specified and as directed

Rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces as in ceiling finished even and fair without using extra cement complete all as specified and as directed.

Rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and fair without using extra cement including mixing of water proofing compound as per manufacturer instructions complete all as specified and as directed. Note: WPC will be measured and paid seperately as suplly only item

Supply only liquid water proofing compound

Rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and fair without using extra cement complete all as specified and as directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like set in cement mortar 1:4, including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L Non-skid ceramic coloured tiles 7 to 8 mm thick (square), size of each tile 400 X400 mm as in floors etc set and jointed in net cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M &L Glazed ceramic coloured disigner / concept tiles in vertical surfaces 300X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles as in skirting/dado including 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

M&L for vitrified light shade tiles 9.5 mm thick ( Square or rectangular) polished, area of each tile not exceeding 0.36 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement incl screed bed or bedding layers of mortars 15 mm thick in CM 1:6 for laying floor finishes complete all as specified and as directed

M&L for vitrified light shade tiles 9.5 mm thick ( Square or rectangular) polished, area of each tile not exceeding 0.36 sqm in skirting /dado / risers of steps etc set and jointed in neat cement slurry and pointed in coloured cement. including rendering 10mm thick in CM 1:4 complete all as specified and as directed

Preparation of new plastered surface of wall and applying 1.0 mm thick wall care putty and making the surface smooth followed by two coats of distemper oil emulsion, ( ready mixed), of approved manufacturer, of required shade and colour over a coat of alkali resistant primer complete all as specified and as directed.

Preparation of newly plastered surface of wall and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed .

Preparation of old plastered ceiling surfaces and applying two coats of oil emulsion paint complete all as specified and as directed .

M & L 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid , rounded or chamfered, put together with glue pinned at joints complete as specified and as directed.

M&L factory made 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, with both face decorative face veneer with lipping complete as specified and as directed.

S &F factory made 30mm thick 2nd class wood glazed and skeleton shutters open rebated and prepared to receive glass gauze etc ( with out sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass, wire cloth etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and as directed.

S&F butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22, 100 mm long, complete all as specified and as directed.

S&F aluminium (extruded section body) door closer hydraulically regulated designation No. 2, universal type suitsble for door shutter of 701 to 850mm in width and of weight between 36 to 60 Kg complete all as specified and as directed .

Preparation of new wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F 150 mm long brass handles, caste type polished bright complete all as specified and as directed

S &F aluminum anodised handle cast type of 150mm long complete all as specified and as directed.

S & F 200mm long brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed

S & F Aluminum anodised barrel tower bolts of extruded section 200mm long complete all as specified and as directed.

S & F brass sliding door bolts of 300mm long with sand or die-cast brass hasp,staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and directed.

S & F aluminum aodised sliding door bolts of 300mm long with hasp and staple(bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S & F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples, complete all as specified and as directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube etc complete all as specified and as directed

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in the frame at site complete all as specified and as directed .

S&F aluminium powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame section of door, windows, ventilation, partion wall, cup board with one or more rebates including joinging cleats for fixing etc. complete all as specified and as directed.

S&F aluminium powder coated anodised aluminium window and ventilator shutters, fixed type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws complete all as specified and as directed .

S&F aluminium powder coated grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and as directed.

S&F Toughned glass 12 mm thick as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required glazinh with beads fixed with metal panel pins complete all as specified and as directed

M&L rotational moulded polyethlene water storage tanks of capacity 500 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm dia ball brass valve high pressure with polythene float including dismantling of existing PVC tank of any capacity complete all as specified and as directed.

S & F 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified and as directed.

S & F 16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified and as directed.

S&F in repairs wall Mixer 3-in-1 system with provision for both Hand shower & overhead shower complete with 115mm long bend pip on upper side, connecting legs and flanges (without overhead shower) complete all as specified and as directed.

S&F fancy type stop valve/ Angle valve cast copper alloy (ISI Marked) chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15mm bore dia complete all as specified and as directed.

S&F for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S&F overhead shower 120x120mm square shape single flow (face plate stainless steel & ABS body in chrome finish) with rubit cleaing system complete all as specified and as directed.

S&F liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 105 gms) complete all as specified and as directed.

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and as directed.

S & F peg set of six powder coated fixed with chromium plated brass screws and wooden and plastic cleats ( min wt 190 gms) complete all as specified and as directed.

S&F towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified and as directed.

S&F one piece western toilet / water closet commode with seat (S Trap) outlet western commode white including flushing cistern within one piece, decorative with push bottom water flush on top complete all as specified and as directed.

S&F ceramic white counter top WHB, decorative type complete all as specified and as directed .

S&F 32 mm waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F PVC (SWR) pipes, 75 mm dia bore, single socketed, in any length with using rubber joints, laid in trenches or in floors complete all as specified and as directed.

S & F PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75 mm dia of outlet, complete all as specified and as directed.

S&F discharge pipe 40 mm dia bore Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 40mm-270 gms) complete all as specified and as directed.

S & F PVC (SWR) bend, 75 mm dia bore,any radius complete all as specified and as directed

S & F PVC (SWR) bend, 75 mm dia bore any radius provided with access door complete all as specified and as directed

S&F 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls with and including clamps complete all as specified and as directed

S&F 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls with and including clamps complete all as specified and as directed

S & F PVC (SWR) bend, 110 mm dia bore,any radius complete all as specified and as directed

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 depth and getting out in soft / loose soil for foundation etc. complete all as specified and as directed .

M&L PCC 1:4:8 type D2 by by using 40mm graded crushed stone aggregate as in foundations, filling and mass concreting complete all as specified and as directed.

M&L cement concrete 1:2:4 type B0 byusing 12.5 mm graded stone aggregate in coping, kerbs, benching and the like, including weathering slighthy rounded or chamfered angles and throating as directed including necessary form work complete all as specified and as directed

M&L PCC 1:3:6 type C1 by by using 20mm graded crushed stone aggregate as in surface channels and drains complete all as specified and as directed.

Precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slab for man holes / drainage / septic tank cover , set in cement mortar 1:4 including necessary from work complete all as specified and as directed. Note: Reinforocement shall be measured and paid seperately.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and as directed.

M&L PCC 1:3:6 type C2 using 40mm graded aggregate, concrete bed to drain pipe 110mm dia bore, including packing under, and haunching against sides of pipes after they are laid and tested in complete all as specified and as directed.

S&F PVC (SWR) pipes, 110 mm dia bore, double socketed, in any length with using rubber joints, laid in trenches or in floors complete all as specified and as directed.

Returning filling in, with excavated soils including spreading, levelling, watering and well ramming in layers n.exc. 25 cm thick complete all as specified and as directed .

Removing excavated material to a distance n. exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and as directed .

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 100mm dia of pipe complete all as specified and as directed .

Hardcore with broken stone aggregate of gauge n.exc 63mm deposited spread and levelled in layer not exc 15cm thick, watered and rammed to true surface complete all as specified and as directed .

M&L 75mm thick PCC 1:3:6 type C-1 using 20mm graded aggregate finished even and smooth without using extra cement as in plinth protection and surface finished even and smooth without using exra cement including making necessary joint complete all as specified and as directed.

S&F for 40mm dia Aluminium decorative end for curtain rods, fixed with nut, screw and washer of stainless steel complete all as specified and as directed .

S&F 20mm dia powder coated aluminium curtain rod fixed with brackets complete all as specified and as directed .

Providing edge moulding to granite stone 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc complete all as specified and as directed

M&L 18 mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on both face, fixed in wall as in decorative frame work for hanging TV etc complete all as specified and as directed

M&L 18 mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, fixed in wall as in decorative frame work for hanging TV etc complete all as specified and as directed

M&L 18 mm wide teak wood lipping, 6mm thick fixed with nail complete all as specified and as directed .

M&L 18 mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, as in pelmet box etc complete all as specified and as directed

S & F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed

S&Fmagnetic catcher suitable for cupboard shutters etc complete all as specified and as directed

S&F SS self closing Earl Bihari cupbard hinging device suitable for 600 wide shutter complete all as specified and as directed

S&F 125 mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with SS screws complete all as specified and as directed

S&F 150 mm long extruded brass handles, fabricated type polished complete all as specified and as directed

French polishing two or more coat on wooden surfaces of any description,including cleaning and preparing the surface including a coat of wood filler on new works complete all as specified and as directed.

Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat/curved surface with sunk and mounting on Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centreand reinforced with G.I. Wire netting of galvanised steel wire 0.71 mm dia with mesh size 12mm fixed with tinned tacks of wire staples complete all as specified and as directed .

M&L factory made 50mm thick chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in foot path, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of the fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed .

M&L kerb stone of 1:1:5:3 type A1 cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm) and making drainage opening wherever required complete all as specified and as directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed .

Point wiring with PVC insulated unsheathed and multistranded copper conductor cable ISI marked, 1100 volt grade FRLS of size 1.5 Sqmm drawn in concealed suitable PVC rigid conduit with all fittings and accessories, fixing one MS pressed 1.6mm thock modular terminal box woth modular white plate of suitable size as required at site with PVC insulated unsheathed stranded copper conductor of size 1.5 Sqmm as earth wire connected common earth dolly as specified for one light / fan point controlled by one switch including cutting chases on wall / floor and making good the disrubed surfaces complete all as specified and as directed .

All as per item No 102.00 here in before but 3 pin 5 amps switch socket out let on independent board

All as per item No 102.00 here in before but one 3 pin 5 amps switch socket out let on same board

All as per item No 102.00 here in before but with cable size 2.5 Sqmm and 2.5 Sqmm as earthwire for 3/5 pin, 15/16 amps socket outlet independent board

S & F modular switch, 1 way, 6A, 1 module complete all as specified and as directed .

S & F modular switch, 1 way, 16A, 1 module complete all as specified and as directed .

S & F ceiling rose 3 terminal 5 Amps 230 volts ISI marked,PVC/Polycarbonate, insulated body complete all as specified and as directed .

S&F modular socket, 6A, 2/3 pin combined 2 module complete all as specified and as directed .

S&F modular socket, 6/16A, 2/3 pin combined 2 module complete all as specified and as directed .

S&F modular Bell push 6A 1 module complete all as specified and as directed

S&F Buzzer, Ding Dong AC. 230 volts,single pole complete all as specified and as directed

S & F angle holder , PVC/ polycarbonate with back plate suitable for batten / angular fitting complete all as specified and as directed .

S & FLED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed .

S&F octane LED Panel slim 12 watt 220 volts AC recessed type down light with high efficiency PMMA diffuser soft glare free light complete with drivers, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed .

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed .

S & F LED light fitting batten fitting 1x 20W, 220V, 4 feet, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed .

S & F LED light batten fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed .

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm complete all as specified and as directed

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. minimun air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed

S & F double door, sheet metal enclosure powder coated SPN DB 12 way with 200 Amps rated bus bar, 230 volt, IP 43 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed

S& F MCB SPN, 40 Amps, 240 volts,10 KA, C curve complete all as specified and as directed. Note : To be fixed at existing VTPN DB at starire case GF -01 Nos Incoming for SPN 12 DB-01 Nos

S& F MCB SP, 5 amps to 32 Amps, 240 volts,10 KA, C curve complete all as specified and as directed

Supply, installation, testing and commissioning of split air conditioning unit 1.5 TR capacity (inverter type) with inbuilt air filter complete with cordless remote control, BEE 5 star rated, latest enegry efficient model eco friendly refrigerant gas, 4500 Kcal/hr, 50 Hz, 240 volts, air cooled condensor with all accessories varied speed including fixing the outdoor unit with suitable site requirement and fixing of indoor unit on high wall with necessary wall cutting/ making holes to pass the refrigerant pipes, drain pipes, cables etc and making good to match with existing finishing complete, providing and making interconnection including refrigerant piping with nitrile rubber insulation from indoor to outdoor as provided by OEM and control cable from indoor to outdoor & power cabling from isolator/enclosure to indoor unit as per site requirement, first charging of refrigerant gas including cordless remote, drain piping of suitable size including connection drain lines from unit to nearest drain points complete all as specified and as directed .

S&F DBOXX protected socket AC Box with one single pole MCB 240 Volts 20 Amps with 3 pin socket complete all as specified and as directed

S&Fvoltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of +/- 2.5% and a capacity of 5 KVA complete all as specified and as directed .

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc complete all as specified and as directed

Submain wiring complete with and including 2 runs of 10 sq mm single core FRLS PVC insulated and unsheathed multistranded copper conductor cable single core 1100 Volts grade drawn through and including PVC Conduit concealed includng cutting chases on wall/floor etc. making good the disturbed surfaces of wall complete all as directed with accessories and one run of 10 sqmm FRLS PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed Note : (a) Two runs of 10 sqmm PVC insulated cable and one run of 10 sqmm cable and one run of PVC conduit shall be measured as one unit length. (b) PVC casing caping wiring shall be provided where concealing wiring is not feasible and the same shall be deemed to included in the quoted rate. No extra cost shall be paid for the PVC casing caping item.

Submain wiring complete with and including 2 runs of 4 sq mm single core FRLS PVC insulated and unsheathed multistranded copper conductor cable single core 1100 Volts grade drawn through and including PVC Conduit concealed includng cutting chases on wall/floor etc. making good the disturbed surfaces of wall complete all as directed with accessories and one run of 4 sqmm FRLS PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed Note : (a) Two runs of 4 sqmm PVC insulated cable and one run of 4 sqmm cable and one run of PVC conduit shall be measured as one unit length. (b) PVC casing caping wiring shall be provided where concealing wiring is not feasible and the same shall be deemed to included in the quoted rate. No extra cost shall be paid for the PVC casing caping item.

Supply, install test and commisssioning LT panel board of size(1000X1000X800)mm out door cubical type factory made double door dust proof CPRI approved and vermin proof fabricated out of CRCA sheet not less than 3.00 mm thick with suitable copper bus bar strip for fixing of two cables with suitable lugs and fixed on angle iron frame made out of 50x50x6 mm grounded in PCC 1:3:6 pedestals,angle iron 450mm above ground level complete all as specified and directed.

STANDARD ENGINEERING (BID ID -3359406)

Abhiraj Enterprises (BID ID -3350945)