Special repair for House No. 60-A on Kunjpura road Karnal

Amount

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantlled :- (HSR 8.18) a) Door

b) Window.

Scraping of cement plaster [HSR 8.32(c)]

Nitching cement concrete surface including preparation of surface (HSR 10.118)

Scraping of White washing & colour washing [HSR 8.32(a)]

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSON. (HSR 14.89)

Providing and fixing ceramic tiles / anti skid tile of size 400 mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, RAK & JOHNSON. (HSR 14.91)

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) a) Size of ceramic Glazed tiles 200 x 300 mm

15mm thick cement plaster 1:4 on the rough side of single or half brick wall. (HSR 15.10)

10 mm thick cement plaster 1:4 on under side of ceiling (HSR 15.52)

Cement pointing 1:2 deep variety on brick and tile work (HSR 15.60)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2).

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3).

Painting two coats with synthetic enamel paint in all shades on old wood-work or metalic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.5)

Applying priming coat with metal primer on new steel or iron work including preparation of surface. Painting on mettalic Surfaces etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.9).

Preparation of plastered surface for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler, consisting of white lead , linseed oil,varnish and chalk mitti including finishing the surface to the required finish complete. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.52)

Distempering with washable oil bound distemper (of approved manufacture) two coats excluding priming coat on new work. (HSR 16.57)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58).

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on new work, two coats to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.61)

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. ( Non coniferous timber other than teak, conforming to I.S. specification No. 1003 kiln seasoned )- ( c) 4 mm thick ( glazing area above 55 sq dm but upto 84 sq dm of each pane) [HSR 17.36( c)]

Cost of iron fittings complete for doors and windows such as tower bolts, handles etc. and screws for these fittings (excluding sliding bolts) a) for single leaf shutter.[HSR 17.71 (a)].

b) for double leaf shutter (HSR 17.71(b)

Providing and fixing helical door spring 150mm (superior quality) including necessary screws ,etc., complete ( b ) iron [HSR 17.79 ( b ) ]

Providing and fixing sliding bolt with nuts and screws, etc., complete (c) iron [HSR 17.83(c)] (a) 300mmx16mm size

b)250mmx16mm size

Factory manufactured panelled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash etc.(non-coniferous timber other than teak, conforming to I.S. specification No.1003, kiln seasoned), with 100mm wide vertical styles, 150mm wide lock rail, 200mm wide bottom rail and 100mm wide other rails, with panels of 12mm thick commercial veneered both sides particle board of plywood of B.W.R. grade, hot-pressed, including cost of iron hinges, screws, chocks/cleats, stops and nails etc. complete fixed in position(excluding the cost of any fittings, other than specified above but including labour for fixing the same in position:- b)35mm thick (HSR 17.91(b)(-)Note (i) under item No. 17.18]

Factory manufactured wire gauze door and window shutters of commercial hard wood, such as hollocks, champ, chikrassy and chaplash, etc., (non-coniferous timber other teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vetical styles, 150 mm wide lock rail, 200 mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chocks/cleats,stops, nails etc., complete fixed in position (execluding the cost of any fittings, other than specified above but including labour for fixing the same in position) [HSR 17.92 (-)Note (i) under item No. 17.18] ii) 35 mm thick.

Wrought iron and mild steel(using angles, flats ,square bars , tee and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Pressed steel sheet frames (chowkats ), consisting of 2mm thick steel sheet of the specified section,including iron lugs(hold fasts) iron hinges conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for fillings in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34) a)Door and Window frame of size 89 mm x 50 mm with 40 mm wide single rebate

Conglomerate floor 40 mm thick cement concrete topping 1:2:4 (HSR 14.9)

Cutting chase in brick walls in cement or in floor for embedding G.I. Or H.C.I. Pipe lines and making good the same to its original condition [HSR 30.95]

Cutting holes upto 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required [HSR 28.24] a) 11.43 cm thickness of walls

b) 22.86 cm thickness of walls

Cutting Holes upto 23 CM square for Pipes in flooring and roofs of bricks tiles with lime concrete and making good Including, repointing, replastering and colour or white washing where required. [HSR 28.25] b) 15mm thickness floor

Providing and fixing in position best Indian make (ordinary)lavatory suites, consisting of Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary. R.S. or C.I. Brackets for building into wall including painting, 32mm C.P. brass waste with C.P brass chain and rubber plug, 15mm C.P. brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-Charge). All fittings best Indian make and; to the approval of the Engineer-in-Charge. All brass work chromium plated and complete in all respect including cutting and making good the walls floors and painting of fittings etc. [HSR 30.41] white (v) Size 560mm × 450 with

Providing and fixing in position on best Indian make Chromium plated brass 2nd Tap for labatory suite [HSR 30.45]

Providing and fixing in position 32mm dia G.I. Waste pipe embedded in wall or lead waste pipe (weighing 3.47kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge)[HSR 30.48]

Providing and fixing in position best quality stainless steel sink of size 600mm x 450mm x 200mm size [HSR 30.53]

Providing and fixing in position Brass OXIDIZED Gas Taps (to the approval of the Engineer-in-charge) complete in all respects. [HSR 30.72] i) One way

Providing and fixing in position super quality 65mm i/d opening C.P. brass dome type hinged grating weighing about 750 gms. Fixed in cement mortar 1:2 complete in all respects ( as required by the Engineer-in-charge) [HSR 30.74]

Providing and fixing in position 15mm i/d C.P.brass & bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75] c) Bib Cock

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge). [HSR 30.76] 15mm stop cock (i) Stop cock make & female end.

ii) Concealed stop cock with flange

Providing and fixing in position best Indian make flexible tube connection [HSR 30.82 b (i)] C.P. Brass (i) 15 mm x 300 mm

Providing and fixing in position automatic brass ball valves in tanks [HSR 30.110] WITH PEASTIC BALL (i) 15mm i/d

Providing and Laying Pre-polished Granite stone 17 mm & above all shades in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone. (NS].

Providing & laying jointing fixing and testing G.I./P.V.C/W.I. pipeline and specials tees bends, sockets, elbows etc. inside building and testing etc., complete including cutting threading (NS) (i) 15mm i/d of pipeline

ii) 20mm i/d of pipeline

Extra for fixing and jointing union couplings in G.I. and W.I. Pipelines. (NS) (i) 15mm i/d of pipeline

ii) 20mm i/d

Recovery items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Dismantiling of bricks and Removing of Door and windos in the DNIT. In case it is not possible to use this material on the work, the agency can take away this material after approval from employer. This material will be issued at the price quoted by the agency. However the reserve price is as under:- i) Doors @ 800/- Each

ii) Windows @ 500/- Each Note:- All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this building. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.

the pal cooperative labour and construction limited karnal