SPECIAL REPAIR TO BUILDING NO P-81 TYPE B AT JAIPUR MIL STN

B/R Portion Taking down existing roof treatment complete including demolition of PCC, Mud phuskas, lime concrete etc any description upto mother slab, and properly cleaning the surface to remove loose particles with wire brushes and removing the debris out side of MoD land complete all as specified and as directed.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying average 40mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) finished even & fair to cover negative slope complete as specified and directed

M&L screed plaster 10mm thick in cement mortar (1:3) on concrete surfaces of roof to receive water proofing treatment finished even and fair incl mixing of WPC as per manufacturers instruction complete all as specified and directed. Noted : WPC shall be measured and paid seperately

Supplying and applying fibre reinforced elastomeric liquid water proofing coating over cementitious surfaces, highly elastic and hair line crack bridging capacity(elongation 250-350%),non toxic,VOC complaint water based coated in four layer first being priming coat,,first coat,fibre reinforced mesh & final coat) as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge. Make:-Asian Paint (smart care damp proof)/Berger (Homeshield Dampstop )/ STP (Shalicry MHI )/Sikalastic 450 I or equivalent Note:- (i) Work shall be carried out through authorised applicator only and contractor shall submit MOU with authorised applicator of approved manufacturer before execution of work. (ii) Material shall be used as per technical data/instruction of manufacturer after written approval of garrison engineer before execution at site including guarantee of roof treatment work for 10 years. (iii) Material incorporated in the work shall be brought at site in one time before commencement of water proofing work.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L pre-cast cement concrete 1:3:6, type C1 (using 20mm graded stone aggregate) block masonry with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster or cement lime plaster, any description on brick, stone walls or concrete surface of ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

M&L for rendering 10mm thick in CM 1:6 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for dismantling loose / cracked concrete, cleaning the rusted reinforcement and exposed surface by wire brush, mechanical device or any other established method and applying the rust removing solution of approved make and quality with cotton swab to reinforcement and allowing to dry the same for 24 hrs, brushing of loose particles and applying 1st coat of rust preventive coating and applying bond coat of epoxy bonding agent & Cement in 1:1 ratio for bondig old and new concrete on damaged surfaces and applying polymer modified mortar in CM (1:3) having 5 mm Avg thickness on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two layers, 1st layer 10 mm thick in CM 1:4 and IInd layer 5 mm thick in CM 1:4 incl mixing of WPC as per manufacturers instruction, on fair faces of brick masonry surfaces or concrete surface, finished even and smooth without using extra cement including necessary scaffolding arrangements up to any height complete all as specified and as directed. Note : WPC Shall be measured and paid seperately

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of premium acrylic exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller over and including one coat of alkali resistant priming paints over 2mm thick wall care putty and rubbing the same to obtain smooth surface for next coat complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of premium acrylic interior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller over and including one coat of alkali resistant priming paints over 2mm thick wall care putty and rubbing the same to obtain smooth surface for next coat complete all as specified and directed.

,--- ditto--- all as per srl item No. 13 above but as in ceiling complete all as specified and directed.

M&L for preparation of old decorated plastered / unplastered surfaces of walls, soffits of chajjas, cornices etc and applying one coat of premium acrylic exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller complete all as specified and directed .

M&L for preparation of old decorated plastered / unplastered surfaces of walls, soffits of chajjas, cornices etc and applying one coat of premium acrylic interior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller complete all as specified and directed.

,--- ditto--- all as per srl item No. 16 above but as in ceiling complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises complete all as specified and directed.

M&L for coloured glazed ceramic tiles 450mm X 300mm X 7 to 8mm thick on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for light shade full body vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete all as approved and directed.

M&L for light shade full body vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for joint free coloured non skid ceramic tiles, 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick of size 550 x 550 mm in floor over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing laid over and including 15 mm thick cement plaster in CM 1:6 including rubbing and polishing complete all as specified and directed

M&L for Polishing to existing Kota stone flooring by using grinding and polishing machine with carborundum stone of required grit size to achieve smooth and glossy finish of kota stone floor complete all as specified and directed

M&L for rubber moulded coloured chequered cement concrete tiles, 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment, laid over and including 15mm thick screed bed in CM 1:4 complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15cm thickness (below or above ground level) complete all as specified and as directed

M&L for 100 mm thick PCC 1:4:8, type D-2(40mm graded aggregate) as in sub base complete all as specified and as directed.

Dismantling CGI / asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and directed.

M&L pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws /J hook, L-type crancked hook complete all as specified and directed

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Two track two panels sliding glazed door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) comprising of uPVC multi-chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC, extruded glazing beads, uPVC extruded interlock and uPVC extruded line sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

S&F for 4.00mm thick sheet glass odinary qulity and glazing with neosprene beading exc 0.5 Sqm in each pane complete all as specified and directed.

Taking down eaves gutters, sanitary PVC pipes and rainwater pipes, cast iron pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wall complete all as specified & directed.

S&F 110 mm UPVC(SWR) ventilation and rain water pipes (type A conforming to IS-13592) single socketed, in any length with rubber ring joints fixed to wallls complete all as specified & directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) junction single (Single Tee) equal or unequal with acess door complete all as specified and directed.

S&F in repair PVC (SWR) floor trap oulet dia 110mm, plain with SS grating including jointing with solvent cemet complete all as specified and as directed.

M & L for 75mm thick PCC 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed

M&L for Rounding to edges of stones slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified & as directed.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation board/ slab/blankets any thicknesss including cover filletes complete all as specified and directed

Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with Dune Tegular 24 Edge Tiles of 16mm thickness and Prelude 24mm face exposed grid. The tiles shall have sand texture visual with acoustical punchers, Humidity Resistance (RH) of 99%, NRC 0.5 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84 with Board edge in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of up to 41%. The tile shall comply with Indoor Air Comfort Gold requirements, version 7.0 (2020) and this certification shall ensure compliance with LEED & DGNB, French VOC class A+, French HQE certification, German Regulation (AgBB/ABG), Italian CAM Edilizia, BREEAM International NOR NL, WELL Building, SKA Rating, BVB (Sweden), Eco Product Norway, Blue Angel DE-UZ 132, M1, Danish Indoor Climate Label, Singapore Green Label and GreenTag Australia. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. SUSPENSION: The tile shall be laid on KCS Prelude 38 with 24 mm wide T - section flanges colour global white (matching to tile colour) having roll formed double stroke rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 15 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 18kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications above) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be KCS wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per recommended procedure. SUSPENSION SYSTEM accessories supplied by consisting of M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners).

S&F urinal spreader of SS any colour for fixing with 15 mm dia pipe complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size 550 x 400 mm excluding taps, chain & plug and porcelene stopper but including brackets /fastners, 32mm dia brass chromium plated waste coupling with long screwed shanks and fly-nuts, 32mm dia PVC waste pipe, flange end bedded in red lead cement and other end fixed, cutting for and pinning in ends of brackets complete all as specified and directed.

S & F in repairs 15mm bore pillar tap, long body cast copper alloy, chromium plated, fancy type with capstan head, screwed down, high pressure with or without lettered 'Hot' or ' Cold' with long screwed shank and fly nuts screwed for iron pipe complete all as specified and directed.

S&F in repair stainless steel grating doom 125 mm dia with or without waste hole complete all as specified & as directed.

S&F in repair 15mm bore stop/angle valves, long shank, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed for iron pipes or for unions and fixed complete all as specified and directed.

S & F in repair 500 Ltrs capacity rotational moulded polyethylene water storage tank, tripple layered (cylindrical vertical with closed top) white colour, hoisted and fixed in position & including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc screwed for iron pipe tank complete all as specified in SSR Part I and directed by Engr in charge.

S&F 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. Note : Minimum weight for 20 mm dia shall not be less than 210gms.

S & F in repair vitreous china half stall urinal (back inlet), size of 340 x 325 x 650 mm white incl providing and fixing plugs, securing urinal to plugs with and including 60mm long brass screws with grating and union for discharge pipe including PVC waste pipe complete all as specified and directed.

S&F in repair vitreous China white single piece EWC (European type) of size 775mm x360mm x660mm incl inbuilt dual flush flushing cistern, S trap and soft close seat cover and mild steel chromium plated or aluminised hinging device and connection to drain (or out going pipe) all as specified and directed

S&F in repair automatic soap Dispenser, 265 X 118 X 110mm size, 0.8ltr capacity and fixed with chromium plated brass screw complete all as specified and directed by Engr In Charge.

S&F in repair 15 mm bore two way bib tap, cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

S&F in repair chromium plated tubular towel ring of size 610 mm included new chromium plated brass screws & plastic rawl plug complete all as specified and directed by Engr In Charge.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth, for foundation etc or for shafts, wells, manholes, pier holes, laying of cables etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

,---ditto--- all as per item No. 63 above but depth exc 1.5m but not exc 3m complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil complete all as specified and as directed.

Removing excavated material to a distance n exc 50 m and deposited where directed at a level n exc 1.5 m above the starting point complete all as specified and as directed.

Supply, laying, jointing and testing of 150mm bore, DWC pipe (Double wall corrugated) of class SN-4 for sewer line, as per IS-16098 (Part –II), laid in trenches and jointed complete including all necessary fittings i.e. coupler, bend, Tee, reducer etc incl demolition and breaking up complete all as specified & directed . Note : Earth work shall be measured and paid seperately

Supply and fix Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. Note :Butt hinges shall be paid separately

S & F 100 mm butt hinges stainless steel (Grade SS-304) medium weight and fixed complete all as specified and as directed.

S&F in repair brass mortice lock, vertical type, size 100 mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified fixed

Material and labour for mild steel Fe-290 (Gde E165) Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (inclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

E/M portion Taking down carefully surface aluminum /copper point wiring, casing capping /PVC concealed conduit for (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified and directed.

Taking down carefully sub main wiring with PVC casing capping / PVC surface conduit and making good disturbed surfaces complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable, single core, 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one light point controlled by one, one way switch 6 Amp complete all as specified and directed.

,---ditto--- all as per item No. 76 above but for one fan point controlled by one switch 6 amp complete all as specified and directed.

,---ditto--- all as per item No. 76 above but for one 3 pin 5 Amp socket outlet controlled by one switch on same board complete all as specified and directed.

,---ditto--- all as per item No. 76 above but for one 3 pin 5 Amp socket outlet controlled by one switch on indepdendent board complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 4 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one socket outlet 16 Amps on independent board or for 20amp single pole sockect outlet complete all as specified and directed.

M&L for sub main wiring with two run of 6 Sqmm PVC insulated FRLSH multistranded copper conductor cable alongwith one run of 6 Sqmm earth wire as earth continuity conductor (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non mettalic PVC conduit of size 25mm, medium grade, ISI marked ivory colour alongwith accessories of suitable size including making connection as required and making good the disturbed portion complete all as specified and directed. NOTE - Two run of 6 sqmm phase and neutral wire & One run of 6 sqmm earth wire & One run of PVC conduit with accessories shall be measured as One length.

,---ditto-- all as per item No. 81 above but two run of 2.5 Sqmm and one run of 2.5 Sqmm earth in 20mm dia PVC conduit complete all as specified and directed.

S&F modular socket 6 Amps, 2/3pin combined 2 module, multi socket for all pins 230 volts AC complete all as specified and directed.

S&F modular switch, 6 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular switch 16 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular socket 6/16 Amps, 2/3pin combined 2 module, multi socket for all pins 230 volts AC complete all as specified and directed.

S&F angle holder, insulated polycarbonate body with back plate complete all as specified and directed.

S&F ceiling rose PVC polycarbonate isolated body, 3 terminals 230 Volt complete all as specified and directed

S&F modular hum free electronic step fan regulator 120-280 volts of 120 watts capacity (socket type) including connecting up complete all as specified and directed.

Taking down MCB distribution board with incoming and outgoing controls any make and capacity after disconnecting complete all as specified and directed.

S&F MCBs Distribution board SPN, 8 ways, 240 volt, powder coated, CRCA steel sheet, degree of protection IP-43, IK09, with reversible double door, 415V, recess mounted having insulated 100 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed. Note : MCBs and MCB DB shall be of same make.

S&F MCBs of 'C' curve double pole 32 to 63 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

S&F MCBs of 'B' curve single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

S&F MCBs of 'C' curve, TPN 16 to 32 Amps having breaking capacity 10 KA, ISI marked 415Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCBs Distribution board tripple pole and neutral (VTPN) 4 ways, powder coated, CRCA steel sheet, suitable for MCCB incomer upto 160amp, degree of protection IP-43, IK09 with reversible double door, 415V, recess mounted having insulated 250 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCCB, MCBs and MCB DB shall be of the same make.

S&F MCCB four pole, 160 amp, 415 volt, adjustable type, with breaking capacity 36KA, thermally adjustable between 70 to 100% including 4 spreader link set of same make as that of MCCB including reqd cable connections with copper lugs of suitable size and testing & commisioning and make good complete all as specified and directed.

S & F in repair 20amp, single pole and neutral socket outlet, with 2 pole and earth, metal enclosed plug top in powder coated CRCA steel sheet enclosure recess mounted with chained matel cover for socket out let with and incl one single pole B curve MCB 16 Amps complete all as specified and directed.

S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-40-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH.

S&F energy efficient recessed mounted LED luminaire suitable for 2'x2' grid ceiling with fullglow fully diffused diffuser and lumen output of 3600 lumens having constant current electronic driver of 36 watt 100 lumen/watt duly connected with 0.5 sqmm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable as required complete all as specified and directed.

S&F LED bulk head light fitting 9/10 watt IP 66 & IK 09 with pressure die cast aluminium housing & polycarbonate diffuser with LED driver duly prewired connection with 0.75sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable complete all as specified & directed.

M&L for taking out exhaust fan metal body sweep 250 mm heavy duty motor, double ball bearings with louver and refixing at new location including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified & directed.

S & F exhaust fan metal body sweep 380 mm heavy duty motor, double ball bearings with louver including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required.

M& L for taking out wall mounted fan, cable end, dismantling blades and removing fan 650mm sweep 50 Hz AC 230 votls, & cleaning servicing and spray painting and re-fixing at new location including fan mounting arrangement with nutS,bolts, 2Xclamps with 1.0 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling as required all as directed.

S&F ceiling fan 1200mm sweep 50 Hz AC 230 votls, white colour with BLDC fan motor, Min air delivery 210 CFM with service value 6.00 BEE 5 star rated incl blade set, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified and directed.

M& L for taking out ceiling fan 1200mm sweep 50 Hz AC 230 votls, and re-fixing at new location including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire,fan hook,motor or ceiling as required all as per directed.

Supplying and fixing greenline high efficiency LED light luminaire 35/40watt complete with drive, pressure die cast aluminium housing, UV stablized polycarbonates cover, in built power unit, IP 65 protection including mounting bracket made of 25 mm GI pipe, medium grade ISI marked not less then 1.2 m bend in shape with two number clamps, nuts, bolts, washeres as required.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.5mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected with GI lead wire 4.0mm dia means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. (Note - GI lead wire of size 4.0mm upto 7.5 m included in the item).

Supply, laying, jointing, testing & commissioning LT cable XLPE insulated, screened PVC bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade (ISI marked) laid in trenches, ducts, pipes or fixed on poles of size 6 Sqmm 4 core including all necessary clamps, nut, bolt washers in repair complete all as specfied and directed .

Supply, laying, jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade (ISI marked) laid in trenches, ducts, pipes or fixed on poles of size 25 Sqmm 4 core including all necessary clamps, nut, bolt washers in repair complete all as specfied and directed .

M & L Sand cushioning to under ground cable with screened and washed sand (non cohessive), 8 cm before laying cable and 15cm after laying and punned to 18cm after laying of cable complete all as specified and directed by Engineer-in-Charge. Note : Punned thickness shall be considered for payment purpose.

M&L for factory made unreinforced pre-cast concrete cable protection cover LV class type-I with size 250mm X 150mm X 40mm laid across the cable (i.e. width of cover along the length of cable) for UG cable protection on the top of the sand cushioning complete all as specified and directed.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

Please Enable Macros to View BoQ information