Loading
Loading…
Loading…
Tender Value
₹2.9 Cr
EMD Value
₹5.8 L
Closing Date
26 Aug 2026, 5:00 pm2d left
SM_TENDER CELL
GNIDA OFFICE
Providing LED street light on Industrial Sector Ecotech-11, Ecotech-2, Ecotech-1 Extn-1, Ecotech-1 Extn., Greater Noida.
2026_GNIDA_1176466_7
SM/(E-TENDER CELL)/2026/787 DATED-10.08.2026
Open Tender
Electrical Works
Percentage
365 days
GREATER NOIDA
REFER TENDER DOCUMENT
5 documents required · 5 mandatory
₹4,690
₹5.8 L
12 Aug 2026
12 Aug 2026
31 Aug 2026
12 Aug 2026
26 Aug 2026
12 Aug 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1BOQ | |||||
| 1.01 | Supply & erection of Steel tubular pole with 1/6 over all length of pole grouted with cement concrete in 1:3:6 (1 cement: 3 coarse sand: 6 stone ballast) including plinthing of pole 30 cm above the ground level, plastering of plinth including excavation back filing etc. The rates includes all materials labour & T&P. etc. Complete in all respects as per direction of E-/c. GNIDA SOR-2024/27 | - | - | - | - |
| 1.02 | 410 SP-51, 11 mtr. (Approx. wt. 169kg.) | 552 | Nos. | 20,600 | ₹1,13,71,200 |
| 2 | Supply & fixing of 8mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 135 mm and base plate12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect. UPPWD-2018/643 | 13 | Nos. | 17,750 | ₹2,30,750 |
| 3LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy >135 lm/Watt). Supplying, Installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC,frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI>70, under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitary) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <5, Maximum power consumption | |||||
| 3.01 | should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above90°C).DSR-2025/8.14 | - | - | - | - |
| 3.02 | 72 Watt (DSR-2025/8.14.13) | 443 | Nos. | 2,227 | ₹9,86,561 |
| 3.03 | 150 Watt (DSR-2025/8.14.17) | 253 | Nos. | 4,396 | ₹11,12,188 |
| 4 | Supply & fixing of 20 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 4 mm. Top dia minium 150 mm, Bottom dia 410 mm base plate 32 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 HP power tool moter, 3 point suspension system with steel wire rope 8 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect. UPPWD-2018/653 | 3 | Nos. | 3,14,000 | ₹9,42,000 |
| 5LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy >135 lm/Watt) Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI>70, under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin) , | |||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 3.75 MB
Tendernotice_2.pdf
PDF • 0.18 MB
PreQ_Prov_LED_Stree_Ligh_Indu_Sec_Ecot_11_2_Extn_1.pdf
Tender Documents • 1.49 MB
BOQ_2210913.xls
BOQ • 0.25 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].