07/EUDC (VIII)/LESA/2024-25

Amount

Safe carriage, loading-unloading with proper stacking of following material from ESC-Daliganj to Work Site/JE -Dump Store –

(a) 11KV 3X70/120/185 SQ MM XLPE CABLE

(b) 11 KV ST/TH C/J KIT 3X70/120/185 SQ MM

(c) 11 KV END TERMINATION O/DOOR & I/DOOR 3X70/120/185 SQ MM

(d) ST POLE 9/11 MT LONG

(g) ABC 3X120+1X95+1X16/ABC 3X95+1X70+1X16

(h) TOP CHANEL 100X50MM

(i) 11KV PIN INSULATOR

(j) Dropper Channel 100x50x2000mm

(k) 11 KV CT & PT Unit

(l) LT Distribution box (3 Phase)

Fabrication & erection of S/S type double pole for 11KV line on 11 M long ST pole with fixing of necessary clamps & other accessories like 1 no. top channel 100×50 mm,2 no.MS angle 65x65x6mm,danger board,number plate,barbed wire,TPMO set & D.O.fuse set.

Supply installation and testing of Single ACB Panel 1600 Amp. 4 pole

Supply of 11 KV RMU (3 way)

Installation of RMU including grouting & plinthing

Wiremesh Fencing for RMU

Laying of 3x70/120/185 Sqmm XLPE cable double circuit by manual method in HDPE pipe.

Hoisting of 11KV XLPE cable3x70/120/185 sq mm

High Pressure testing of 11 KV XLPE cable. Testing equipment will be arranged by the contractor.

Chemical Earthing system with outer pipe diameter 50mm, inner Strip 40x6, length 3000 mm. galvanization up to 200 micro, earthing pipe with crystalline conductive mixture filled inside the pipe with anti-corrosion & high conductive along with 50 Kg(As per required) of BFC which should be capable to reducing the soil resistively with good moisture retaining capacity. (Specification of chemical earthing and drawing is hereby enclosed). All material shall by supply by the contractor.

Construction of T/F plinth of size 2x2x1.5 m on a padding 0.25M deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work Ist class brick of 0.95 mtr hight & 0.35 mtr wall will be constructed. Rest wall should be 0.23 mtr thick brick work in ratio 1:4 cement & cores Sand in the hollow portion the sand should be filled from the ground level up to 15 centimeter below from the top of wall, Cement, sand & brick Ballasts should be filled up to 15 centimeter. Two no. of channel 100x50 in length 1500mm will be grouded.0.35 CM.RCC will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.The t/fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. (All the material will be arranged by the contractor .)

Placement of 11/0.4 KV T/Fs from dump place to newly constructed T/Fs plinth & installation, commissioning 1000/100 KVA T/Fs of T/F Plinth and including jumpering with the system ( All the required material for above job shall be provided by contractor except T/Fs)

Construction of retaining wall, fabrication & erection of Wire mesh fencing around Transformer and Distribution Pillar Box with retaining wall & 1 no. gate with locking arrangement made of MS Angle iron of size 50x50x6 mm jointed with nuts and bolts. The panel must be supported with MS Flat of size 50x6 mm. Wiremesh of size 10 SWG rectangle type, its painting as per norms of RESSPO. (All the material will be arranged by the contractor at his own cost).

Providing earthing strip size 50x6mm and connecting from earthing pipe/m.s.earting rod to fuse unit/tronsformer body/neutral earthing (Earthing rod & earthing strip arranged by contractor).

Fabrication & erection of single pole for LT line on 09/11 M long ST pole with fixing of necessary clamps & other acessories like clamp hook, dead/suspension clamp,neutral clamp,ABC pressure clamp (if required) and danger board with clamp.(all material arranged by contractor except steel & pole if required).

Stringing,Sagging,winding and jumpering of LT line with AB Cable (3x120+1x95+1x16/3x95+1x70+1x16) conductor as per RESSPO Norms.(AB Cable provided by deptt and balance material like holding clamp, eye hook, suspension clamp and dead end clamp arranged by contractor .)

Installation of LT distribution box 3 phase

Fixing of earth rod (2500x20mm) as per norms. For earthing support of old existing poles of LT lines including 6 SWG GI/Earth wire . (All Materials provided by contractor)

Grouting of pole in depth of 1/6 the length of pole in ratio 1:4:8 in cement sand and brick balast as per RESPO norms.

Construction of pole plinth 300mm x 450 mm above ground level in 1:2:4 in cement, coarse sand and stone gritt as per RESPO norms.

Painting of new erected ST pole with two coat of red oxide paint,PO red paint at top of pole 2 M & balance by two coats of best quality aluminium paint ISI of Burger/Nerolac/Asian mark as per norms.

Installation and commissioning of CT/PT Metering unit including its connection in between TVM Meter and CT/PT Unit with required size of copper cable. Cable will be arranged by the contractor as his own cost.

Dismantling of 11KV line, L.T. lines & distribution boxes and its dump at suitable place on site up to completion of work and its safe loading/unloading/weighing carriage from dump site to je"s store/ESC daliganj (Except broken PCC Pole).

ST Pole (with the help of Crain)

11 KV Overhead circuit (Dead Circuit)

P.S. ENTERPRISES

M/s SAMAN ENTERPRISES