Repair to false ceiling, wall paneling, aluminium, plastering, iron gate and shutters in Zone-II under GE (Army) Jaisalmer

Amount

Demolition of cement concrete (un reinforced) in any description and in any position not otherwise specifically provilded complete all as specified & directed

M&L PCC 1:2:4 type B0 25mm thick as in leveling course in sunken portions complete all as specified & directed

Material and labour for applying cold bituminous primer @ 0.30 ltr/Sqm confirming to IS-3384 and laying APP polymer modified membrane non-woven polyester reinforcement of 3mm thick, weighing not less than 3.5 Kg/Sqm with plain polythene finish and sealing all the over laps of 75mm in length side and 100mm on the width side of membrane by torching the same all as per manufactures instructions and all as specified and directed. Including removing existing unserviceable water proofing treatment and washing down with water to remove all dirt etc. also including 50 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floors, roof padding & finished the surface even & fair without using extra cement including approved water proofing compound as per manufacturer's instructions or by 3% of weight of cement all as specified.

M&L Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre on concrete surfaces and sanding complete all as specified & directed.

S&F Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq.m complete all as specified & directed.

M&L rendering 10mm thick in CM 1:4 finished fair and even with WPC @ 3% by wt of cement complete all as specified.

Supply only water proofing compound complete all as specified.

Taking down shutters of any description not exceeding 1.00 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each complete all as specified & directed by Engineer-in-charge.

Resecuring or easing and adjusting shutters of any description exc 1 Sqm and not exc 2 Sqm each without taking down of sutters complete all as directed.

S&F in repair MS powder coated drapery rod 25mm dia decorative manner all as per sample all as specified & directed by Engineer-in-charge.

S&F in repair brackets powder coated fancy type suitable for drapery rod 25mm dia all as per sample all as specified & directed by Engineer-in-charge.

S&F box type factory made steel windows exc 1.5 sqm each with gauge shutters & glazed shutter including hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

Repair of steel window shutter not exc 1.5 Sqm each by replacing projected type unserviceable hinges, with welding new hinges or welding of existing broken hinges and handles to window frames and easing of shutters to proper closing with oiling to hinges and painting at welded portion to match the existing surfaces each all as specified & directed by Engineer-in-charge.

S&F, stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.00mm and fixed with stainless steel wire staples complete all as specified & directed by Engineer-in-charge.

S&F in repair, stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.00mm and fixed with stainless steel wire staples complete all as specified & directed by Engineer-in-charge.

S&F 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & directed by Engineer-in-charge.

Hacking out old broken glasses (any thickness, size, quality or description) from steel/wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified & directed by Engineer-in-charge.

All as per item No. 19 above but from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified & directed by Engineer-in-charge.

S&F in repair, 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete including welding if required for fixing in case of pressed steel chowkat all as specified & directed by Engineer-in-charge.

S&F Aluminium (Die cast) door closer hydraulically regulated designation No. 3, universal type, suitable for door shutter of 851 mm to 1000mm in width and of weight between 61 to 80 Kg complete all as specified & directed by Engineer-in-charge.

S&F in repair, aluminium (Die cast) door closer hydraulically regulated designation No. 3, universal type, suitable for door shutter of 851 mm to 1000mm in width and of weight between 61 to 80 Kg complete all as specified & directed by Engineer-in-charge.

S&F safety lever lock, mild steel with 4 levers for rolling shutters complete all as specified & directed by Engineer-in-charge.

S&F, 3mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each panes complete all as specified & directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

S&F, 5.5 mm thick sheet glass, ordinary quality and glazing in squares exceeding 0.5 Sqm in each pane including solar control film 50 micron all as specified & directed by Engineer-in-charge.

S&F,100mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed by Engineer-in-charge.

S&F 125mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified & directed by Engineer-in-charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified & directed by Engineer-in-charge.

Taking down Aluminium anodised door, window and ventilator complete.

S&F Aluminium anodised frame for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F Aluminium anodised window and ventilator shutters, fixed type without sash bar aluminium section wt 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised snap beading , screws etc, complete all as specified.

S&F Anodised aluminium door shutters, aluminium section wt 0.55 kg/m including necessary jointing cleats, glazing clips rubber neoprane packing, handles 2 Nos in each door hinges, anodised aluminium snap beading screws etc complete all as specified.

S&F 5.5mm thick sheet glass, ordinary quality and glazing in squares not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

M&L for repairs of rolling shutter any type area not exceeding 5 Sqm (push pull or manual or gear operated) after opening hood cover and without taking down rolling shutter, by cleaning greasing oiling and renewal of rusted nut bolts including welding as requires for smooth functioning including necessary oiling/ greasing etc after cleaning of the side guided channels of rolling shutters complete all as specified & directed by Engineer-in-charge.

All as per item No. 35 above but of area exceeding 5 Sqm but not exceeding 10 Sqm each.

M&L for Oiling & greasing to the MS shutters by removing the scales and make the shutters to swing freely all as specified & directed by Engineer-in-charge.

Taking down unserviceable rolling shutter of any description any size height more than 4 mtrs complete all as specified and directed by Engineer-in-charge.

S&F Steel rolling shutters of 1.25 mm thickness laths without ball bearing (push pull or manual type) as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position all as directed by Engineer-in-charge.

All as per item No. 39.00 above but gear operated type with bevel gear box and crank handle all as directed by Engineer-in-charge.

S&F Ball bearing for rolling shutters complete all as specified and directed by Engineer-in-charge.

S&F in repair, 18/19mm thick prelaminated particle board/ MDF board interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete as directed by Engineer-in-charge.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings, frame work of water tanks and similar work confirming to Fe-290 grade E-165 complete all as specified & directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with single piece extruded PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement of single piece extruded PVC profile for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm single piece extruded PVC profile with MS square tube, supplying and fixing in opening as per specifications & directed by Engineer-in-charge.

S&F 150 mm size aluminium anodised barrel tower bolts of extruded section all as specified & directed by Engineer-in-charge.

S&F 150 mm size extruded aluminium handle, fabricated type, anodiesed complete all as specified & directed by Engineer-in-charge.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straigth or curved) complete all as specified & directed.

M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

S&F for floor spring double action hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of MS heavy duty complete all as specified & directed by Engineer-in-charge.

Repair of aluminium shutter of any description and size including taking out the shutters and refixing in the same opening and easing of shutters to proper closing with oiling to hinges, floor springs etc all as specified and as directed by Engr in charge

M&L steel door stoper double shoe fixed in door shutters all as directed fixed in repairs complete all as specified & directed by Engineer-in-charge.

S&F megnatic catch for cup board shutter complete all as specified & directed by Engineer-in-charge.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed by Engineer-in-charge.

Dismentaling floor hearth or wall tiling including cement mortar bedding and removing unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed.

Demolition of brick work /stone masonry built in cement mortar incl coping of any description all as specified and directed.

M&L squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 all as specified.

…ditto…all as per ser item No. 57 above but except sotne.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified.

M&L for Keyed pointing to rubble masonry uncoursed or brought up to courses in cement mortar 1:4 all as specified.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of flooring / hardstanding complete.

M&L for 25 thick sand cushing for laying of precast concrete interlocking tiles including watering and consolidation complete.

M&L for 60mm thick inter locking cement concrete mixed colour factory made paver blocks M-35 designation (compressive strength) laid over 25 mm thick sand cushion to maintain the slope including compaction with 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base etc complete.

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floorS&Finishing the surface even & smooth without using extra cement complete.

M& L for PCC 50mm thk type C1 1:3:6 (20mm graded stone aggregate laid in alternative as in plinth protection including finished the surface even and fair without using extra cement and filling the joints with mastic filling ie one part of bitumen 85/25 & 3 parts of sand by weight complete all as specified.

M&L for non skid ceramic coloured tiles of size 300x 300 by 7mm thick joint free grade B-II (a) superior quality confirming to IS 13755 as in floors set & jointed in neat cement slurry and pointed in coloured cement to match the tiles and including scread bed or bedding layer 15mm thick in CM 1:6 all as specified.

M&L for ceramic tiles exterior grade 300 x 300 x 10mm (Endura from Johnson or equivalent) including screed bed in CM 1:6, 15 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match all as specified and roughening of exc concrete surfaces all as directed.

M&L for Granite (of any type) tiles18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types complete all as specified.

M&L for glazed ceramic coloured tiles 450x300x7mm thick in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 etc. complete all as specified.

M&L for non skid ceramic coloured tiles exterior grade but exc 0.18 sqm and n.exc 0.38sqm (600mm X 600mm) ,8-10mm thk including scrrd bed or bedding layer 15mm thk in CM 1:6 all as specified.

...ditto... above but as in skirting, steps etc in vertical surfaces with 10mm thick backing coat in CM 1:4 complete all as specified.

M&L for machine cut kota stone flooring 550 x 550x 20 to 25mm thk laid over cement screed bed jointed & pointed with grey cement slurry mixed with pigment to match the shade including rubbing &mirror polishing including over a screed bed or bedding layer of 15mm thk in CM 1:6 for laying floor finishes all as specified and directed.

...ditto... above but on verticle surfaces such as skirting /dado etc including over a screed bed or bedding layer of 10mm thk in CM 1:3 for laying tiles all as speciifed.

S&F in repair Bib tap cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia complete all as specified.

S&F in repair looking mirror 600x450mm with PVC sheet frame and back supported with 6mm thick AC building board or plywood sheet complete all as directed by Engr-in-Charge.

Dismantling asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings complete all as specified & directed by Engineer-in-charge.

S&F Pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet/ semi corrugated 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws as specified.

S&F Rolled mild steel framed work as in door or gates of angle or other section confirming to Fe - 410-S with gusset plates, rail braces etc complete drilled for fixing of steel sheeting or other covering and hanging and fixing complete all as specified.

S&F Joist, channel, angel or tee sections, fixed independently, without connecting plates etc. complete all as specified.

Taking down cement or cement lime plaster, any description on brick or stone surfaces ofany position etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L for rendering 15 mm thick plaster in cement mortar (1:6) on fair faces of brick work or concrete surfaces of walls and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge.

M&L for rendering 15 mm thick plaster in cement mortar (1:4) on fair faces of brick work or concrete surfaces of walls and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge.

M&L for rendering 10 mm thick plaster in cement mortar (1:3) mixed with WPC on concrete surfaces of roof top and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge. (Note :- WPC will be measured & paid seperately as supply only).

M&L for plastering 5mm in CM 1:4 on ceiling / chajja complete all as specified and directed.

M&L for preparation of old decorated existing surfaces and applying one coat of white wash on walls including in narrow width, bands, cornices, plasters etc complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coat of white wash on walls complete.

M&L for preparation of new plastered surfaces and applying three coat of white wash on ceiling complete.

M&L for two coats of cement base paint over a coat of cement primer on walls complete.

M&L for preparation of new steel surfaces exc 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer primer complete.

M&L for preparing new plastered surfaces and applying two coats of oil bound distemper over one coat of primer wall putty including preparatory to distempering on surface of walls complete.

M&L for 35mm thick precast cement concrete louvers and jallies type C-0 (1:3:6) using 12.50mm graded aggregate (measured solid), including all mouldings but excluding frame, set in cement mortar 1:4 all as directed.

M&L for plain cement concrete 1:2:4 type B 1 using 20mm graded stone agregate cast in situ kerb stone ,copings,bed plates ,water through and the like including wethering ,slightly rounded or chamfered angles and throating including use of form work (straight or curved ) set in CM 1:4 complete all as specified and as directed by Enginneer in charge.

Taking up or down steel tubing 15mm dia and connections including cleaning for refixing complete.

..ditto...all as per ser item No 93 above but 20mm dia complete.

S&F 15mm dia medium grade GI tubing with all fitting and fixed to wall, ceiling or laid in floors etc complete.

...Ditto... All as per ser item No 95 above but 20mm dia.

Dismantling water tanks and removing to store (exc 250 and not exc 500 ltr capacity).

Dismantling water tanks and removing to store (exc 500 and not exc 1000 ltr cap).

S&F in repair 500 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in postion including taking down of old unserviceable water storage tank all as directed by Engg-in-Charge.

-Ditto- All as per ser item No 99 above but 1000 ltr capacity.

S&F in repair 20mm bore dia ball brass valves high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and complete all as specified and as directed by Engr-in- Charge.

S&F 12 mm thick standard seamless, gypsum board plain board insulation as in ceiling, flat or sloping (pattern as per manufacturer's catalogue/ instructions) , rapid joint compound paper tape 50 mm wide, easy finish compound, cutting holes for electrical fittings including preparation of surfaces, filler coat with filler or liquid filler, transparent and bringing forward surfaces to smooth even finish and applying two coats of oil bound distemper complete fixed on and including galvanised iron frame work comprising of galvanised iron perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long with and including ceiling section (not exc 1.2 metre length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including necessary scaffolding all as specified and directed by Engineer-in-charge.

S&F in repair Vitreous china urinal ,half stall type, complete incl providing and fixing plugs bedding urinal against wall in CM1:4 securing urinal to plug with and incl 60mm long brass screws ,pointing around urinal back in cement, incl grating union for discharge pipe etc.

S&F in repair vitreous china wash basin white flat back size550x400mm excl chain and plug and porcelain stopper but incl CI bracket. PTMT waste coupling and PVC waste pipe 75 cm long and 15mm dia PVC connection etc complete.

S&F in repair vitreous china squatting pan orissa pattern size 580x440mm white with integral foot rest including P or S trap and concrete for necessary fixing complete.

S&F in repair Chromium plated tubular aluminium anodised 60 cm long towel rail 20mm dia D type complete fixed with screws etc.

S&F in repair Plastic EWC seat cover, coloured closed pattern with flat bottom and cover of cera model cat pt 2308 and mild steel chromium plated or aluminised hinging device complete.

S&F in repair PVC low level white flushing cistern syphonic action type 10 ltrs capacity incl flush pipe 32 mm dia incl PVC connection 450 mm long and complete fixed in repairs. Make Prayag,Cera Cat Part No-B1010102, Hindware)

S&F in repair Vitreous china wash down water closet pan(Pedestal pattern), white (EWC)with necessary P/S Trap and fixed in repairs including jet spray and seat cover(Cera Cat Part No-S1050104, hindware cat Part No-20011)

BHAGWATI CONSTRUCTION