SPECIAL REPAIRS TO BLDG NO. T-3 OR MD ACCN AT RA LINE OF CAFVD AND GOVT MD ACCN 08xMD ACCN BLDG NO P 27 AT MG ROAD NEAR KIRKEE RLY STN UNDER GE CENTRAL KIRKEE

Amount

Dismantling single or double layer Mangalore pattern or similar tiles or ridge in roofing complete all as specified and as directed.

Supply and fix pre- painted galvalume aluminum zinc coating GI based semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling timber in scantling 40 sq.cm and over in section in any position unframed work and any description complete all as specified and directed.

Supply and fix roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe- 290 (Gde E-165) complete all as specified and as directed.

Supply and fix for E-board 'Everest' make 595x595x4mm thick white prelaminated sett embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white, the frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers, hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and justers and screws etc., the last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall, flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour including taking down wall/ceiling boards(fibre, pulp insulation etc) or insulation boards any thickness including fillets complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, walls, water staging etc, but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and as directed.

Material and labour for brickwork with subclass ‘B’ bricks using old size bricks, straight or curved on plan exc. 6m mean radius built in CM (1:4) complete all as specified and as directed.

Material and labour brick work with fly ash old size bricks straight or curved on plan exc. 6 m mean radius built in CM (1:6) complete all as specified and as directed.

Taking down cement plaster on wall /concrete surface etc including racking out joints hacking for key scrubing down with water etc all as specified and as directed.

Material and labour for rendering 15mm thick plaster in cm (1:4) on fair faces of brick work or concrete surfaces including finishing the surface fair and even using water proofing compound all as specified and directed. NOTE :- (i) Plaster work in Four story building on wall surface. (ii) Water proofing compound paid and measured separately)

Supply only integral liquid water proofing compound complete all as specified and as directed by Engr-in-Charge.

Material and labour for rendering 10 mm thick on fair faces of brick/ block masonry surfaces on walls in CM (1:6) finished even and smooth complete all as specified and as directed by Engr-in-Charge.

Material and labour for rendering 5mm thick plaster in CM (1:3) on fair faces of brick work or concrete as in ceiling including finishing the surface even and smooth without using extra cement all as specified and directed.

Material and labour for preparation of new plastered wall surface and applying two coats of oil bound distemper emulsion white or tined over one coat of alkali resistant primer, on plastered surfaces, preparatory on wall complete all as specified and directed by Engr-in-Charge.

Material and labour for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke soots, moulds, moss efflocerent salts and treading oil and greasy spots, applying two coats of oil bound distemper emulsion complete all as specified and as directed.

Material and labour for preparation of plastered new wall surfaces and applying two coat cement base paint over priming plastered and other surfaces with alkali resistant priming paint on exterior wall complete all as specified and as directed by Engr-in-Charge.

Material and labour for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke soots, moulds, moss efflocerent salts and treading oil and greasy spots and applying two coats of cement based paint complete all as specified and as directed.

Material and labour finishing new walls surfaces with premium acrylic smooth exterior paint with silicone additives of required shade with two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces any description not otherwise provided applying three coats of white wash on ceiling complete all as specified and as directed by Engr-in-Charge.

Material and labour for preparation of old surfaces of any description not otherwise provided applying two coats white wash on ceiling complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats and frame area n.exc 1.5 sqm each including shutters without taking off shutters from the frame and removing from site complete all as specified and as directed.

Taking down chowkats and frame area exc 1.5 sqm but n.exc. 4.00 sqm each including shutter wiuthout taking off shutter from the frame and removing from site complete all as specified and as directed.

Supply and fix aluminium anodised barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and as directed.

Supply and fix aluminium anodised handle cast type, of size 150mm, fixed with screws or welded, complete all as specified and as directed.

Material and labour 200mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

Material and labour 150mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

Supply and fix 300mm long mild steel sliding door bolts, bolt or clip type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

Supply and fix pressed steel frames made out of 1.25 mm thick MS sheet of size 125x60mm for doors, ventilator with double rebates including necessary fixing lugs, hinges, lock strike plate etc, including material and labour for providing PCC (1:2:4), type B1 using 20mm graded stone aggrgate to fill the frame and making good complete all as specified and as & directed by Engr-in-Charge.

Supply and fix pressed steel frames made of 1.25 mm thick MS Sheet size 105 x 60mm for doors, ventilator with single /double rebates including necessary fixing lugs, hinges, lock strike plate etc, including material and labour for providing PCC (1:2:4), type B1, using 20mm graded stone aggrgate to fill the frame and making good complete all as specified and as directed by Engr-in-Charge.

Supply and fix 35 mm thick factory made shutters of second class hard wood plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated supplied and fitted to chowkat complete all as specified and as directed.

Material and labour for 35 mm thick 2nd class hard wood glazed/gauzed and skelton door shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat complete all as specified and as directed.

Material and labour preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, etc treating ends of posts, backs of chowkats, etc., complete all as specified and as directed.

Material and labour for Providing and fixing 30mm thick FACTORY MADE MOULDED DOOR SHUTTER ‐ WOOD FREE consisting of frame made out of MS tubes of 19 gauge thickness and size of 25mm x 25mm for stiles, top and bottom rails. MS frame shall have a coat of steel primers, the inner panel shall consist of 25mm thick EPS of density 23 Kg /cum, bonded with 2mm thick termite proof, water proof and fire resistant moulded PVC Sheet manufactured by an ISO‐9001‐2015 certified company, with 2, 4, 6 raised panel design in different plain and / or prelam colours after routing the moulded design on one side & 2mm plain and /or prelam PVC sheet on other side of the EPS. The edge of panel to be sealed with lipping of 15mm wide PVC sheet batten ( made by sticking 2mm rigid foam PVC sheets of 5mm (±0.25) thickness using PVC solvent cement ) and stile sides 25mm (5mm x 5nos.) thick and 30mm width PVC sheet fitted along MS tube for hardware provision & for lock 25mm thick ( 5mmx5nos. ) PVC sheet of size 150mm x 200mm fixed with inner side of EPS Panel etc. complete all as per specification & drawing and as directed by Engineer-in-charge.

Supply and fix factory made internal PVC door frame of size 50x47mm single riveted made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube, the two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed.

Material and labour for plain cement concrete, (1:3:6), type C1 using 20mm graded stone aggregate as in steel frame filling/hold fast blocking including necessary form work complete all as specified and as directed.

Supply and fix aluminium louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. complete all as specified and as directed.

Supply and fix for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Supply and fix for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

Supply and fix mild steel window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fix in repairs 300mm, ordinary rat tail rod pattern springs including roller and roller plate fixing in wooden or steel door frame using nails or welding complete all as specified and as directed.

Supply and fix 3mm thick sheet glass ordinary quality & glazing with oil putty or fitted with beads in squares n.exc. 0.50 sqm in each pane complete all as specified and as directed.

Supply and fix for galvanised MS wire mesh 0.63mm nominal dia of wire and average width of appearature 1.40mm fixed with tinned tack or galvanised wire staples complete all as specified and as directed.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primere complete all as specified and as directed.

Material and labour for preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc,. Laid, bedded and pointed in any cement mortar complete all as specified and as directed.

Material and labour 25 mm thick PCC (1:2:4), type B-1 using 20mm crushed stone aggregate as in leveling course including demollition of existing PCC complete all as specified and as directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premisess complete all as specified and as directed.

Material and labour for coloured non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM (1:6) including complete all as specified and as directed.

Material and labour for coloured Nano polish ceramic tiles 600x600x8 to 10 mm thick (square/ rectangular) in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM(1:6) including demolition of existing floor tiles, stone slab of any description complete all as specified and as directed.

Material and labour Glazed ceramic colour tiles in vertical surfaces 300x600x7-8mm thick with necessary border etc set and jointed in neat cement slurry and pointed in coloured cement to match over including 10mm thick rendering back coating in cement mortar (1:4) including dismantling of old tiles all as specified and directed.

Material and labour for coloured non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

Material and labour machine cut Kota stone slab flooring (mirror polish) 15-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 15mm screed bed in CM (1:6) set and joined in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

All as per Sl Item No. 53 above but as in skirting complete all as specified and as directed.

Material and labour Chittoor black Granite work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade over and including 15mm screed bed in CM (1:4 )set and joined in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Supply and fix 15mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor including taking down old existing GI pipe any type any size complete all as specified and directed.

Supply and fix 20mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floors including taking down old existing GI pipe any type any size complete all as specified and directed.

Supply and fix in repairs 20 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fix in repairs bib tap long body cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down, screwed for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed. MAKE :- Prayag Cat Part No :8308 or techno commercially equivalent makes specified in PS.

Supply and fix 500 ltrs Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old tank all as specified in SSR Part I and as directed.

Supply and fix in repairs 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm dia - 210 gms) complete all as specified and as directed.

Supply and fix in repairs cast iron nahani trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 100 mm, complete all as specified and as directed.

Supply and fix in repairs cast iron floor trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 100 mm, complete all as specified and as directed.

Supply and Fix vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) 'P' or 'S' trap connecting to flush pipe and to anti syphonage pipe, all as per CERA Cat No CALINA S 3010102 or techno commercially equivalent makes specified in PS. complete including making good to floor fixed in repairs complete all as specified and as directed.

Supply and fix in repairs vitreous china wash basin white flat back size 550 x 400 mm excluding taps waste chain and plug and porcelain stopper but including necessary brackets CP wastes and other fittings complete all as specified and as directed.

Supply and fix in repair pillar taps, chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered Hot Or Cold with long screwed shanks and fly nuts screwed for iron pipes 15mm bore dia pipe complete all as per Prayag Cat Part No 8304 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Supply and fix in repairs angle stop valve cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down, screwed both end for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed. MAKE :- Prayag Cat Part No :8310 or techno commercially equivalent makes specified in PS.

All as per Sl Item No. 67 above but 20mm dia complete all as specified and directed. MAKE :- Prayag Cat Part No : 8710 or techno commercially equivalent makes specified in PS.

Supply and fix brass chromium plated tubular towel rail, 20mm dia, 50cm long all as per Prayag Cat No.BA-01 or techno commercially equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

Supply and fix in repairs CP shower rose 225mm round with arm and flange including fixing to steel pipe fixed in repairs as directed. MAKE :- Prayag Cat Part No BS-67 or techno commercially equivalent makes specified in PS.

Material and labour PVC valveless, syphonic action type, flushing cistern, 10ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, all as per ESSCO Cat No. WHE-WHT-183NL or techno commercially equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

Supply and fix 110mm dia PVC (SWR) pipes, type 'B' single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position including taking down old pipe in any type and position including all fittings complete all as specified and as directed.

Supply and fix 75mm dia PVC (SWR) pipes, type 'B' single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position including taking down old pipe in any type and position including all fittings complete all as specified and as directed.

Supply and fix in repairs PVC (SWR) bends type 'B' of any radius 75mm bore complete all as specified and as directed.

Supply and fix in repair 110mm PVC (SWR) branch piece, type 'B' (Double Y) equal or unequal with access door complete all as specified and directed.

Supply and fix in repair 110mm PVC (SWR) junction single, type 'B' (single T) equal or unequal with access door complete all as specified and directed.

Supply and fix in repair 75mm PVC (SWR) junction single, type 'B' (single T) equal or unequal with access door complete all as specified and directed.

Supply and fix in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving below or above GL complete all as specified and as directed.

Demolition of unreinforced cement concrete (below or above GL) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Repair to sunken floor and trap floor including inside wall as follows : 1) Cut, open and clean cracks in the sunken floor and side wall and repair them with polymer modified mortar 15mm thick modified with Dr. Fixit Pidicrete URP. 2) Prime the surface with Dr. Fixit Primeseal and allow it to dry. Apply the first coat of Dr. Fixit Newcoat. 3) While it is still wet, place a woven glass fibre mesh of measurements 2 mm x 2 mm and allow it to soak completely. 4) Apply the second coat with a roller or squeeze, to ensure complete coverage of the fibre mesh. 5) Apply the third coat after 6 to 8 hours, once the second coat is dry.

Material and labour for PCC 1:5:10 type E-2 (using 40mm graded agg) as in sub base of WC sunken floor complete all as specified and directed.

Material and labour in repair 40mm dia GI pipe medium grade cut to shape and fix to wall or floor of sunken floor as spout or drain out water pipe or as in road crossing complete all as specified and directed.

Material and labour for 75mm thick PCC (1:3:6) type C2, using 40mm graded stone aggregate as in plinth protection including finishing even and smooth without using extra cement complete all as specified and directed.

Material and labour for forming construction joint 30mm deep x 10mm wide filled with sealing compound Grade B for 75mm thick concrete slab complete all as specified and as directed.

Supply and fix in repairs curtain rails, anodised aluminium alloy with brackets, stops, rollers etc. complete all as specified and directed by Engr-in-Charge.

Material and labour for plain cement concrete (1:4:8) type D-2 using 40 mm graded coarse aggregate in bed to drain pipes of 150 mm bore including forming cradles complete all as specified and as directed.

Demolition and breaking up drain pipes (salt glazed ware AC/RCC) drain pipes set in cement mortar, dia of pipe 150mm complete all as specified and as directed.

Material and labour for reinforced concrete pipes, 150 mm bore, Class NP-2, laid and jointed complete with collars complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of pipe and getting out in soft loose soil complete all as specified and as directed.

Excavating in trenches n. exc. 1.5 m wide and n. exc. 1.5 m in depth; for foundation etc or for manholes, laying pipes etc and getting out in hard dense soil complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of pipe and getting out in soft disintegrated rock complete all as specified and as directed.

Excavating in trenches n. exc. 1.5 m wide and n. exc. 1.5 m in depth; for foundation etc or for manholes, laying pipes etc and getting out in hard rock complete all as specified and as directed.

Material and labour plain cement concrete (1:4:8) type D -2 using 40 mm graded coarse aggregate as in foundations filling and mass concrete complete all as specified and as directed.

Material and labour for PCC (1:2:4), type B-1 using 20 mm graded coarse aggregate finished even and smooth without using extra cement in coping including necessary formwork and benching in bottom of manholes drain etc complete all as specified and as directed.

Returning, filling in soil spreading, levelling, watering and well ramming in layers n. exc. 25 cm. complete all as specified and as directed.

Removing excavated soil to a distance n.exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and as directed.

Demolition of reinforced cement concrete manhole covers n exc. 15cm thickness below or above ground level complete all as specified and as directed.

Material and labour for precast cement concrete (1:2:4), type B-1, using 20 mm graded coarse stone aggregate as in cover slabs set in CM (1:6) complete all as specified and as directed.

Material and labour for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bend to shape required, including cranking, bending and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket, power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surface of walls, floors, etc complete all as specified and as directed.

Material and labour for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sq.mm (nominal area) drawn in and including PVC casing caping of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH copper conductor cable of size 1.5 sq.mm as earth lead and connected to earth dolly for one light point or one fan / exhaust fan point or one call bell point controlled by one, one way switch including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch, regulators or bell push and casing caping terminal box for mounting ceiling rose/ holders etc complete all as specified and as directed.

All as per Sl Item No. 104 above but for one three pin 5 Amp socket outlet point with cable of size 1.5 sq.mm size on independent board all as specified and as directed by Engr-in-Charge.

All as per Sl Item No, 104 above but for one three pin 5 Amps socket outlet point ,with cables 1.5 sq.mm size on same board all as specified and directed by Engr-in-Charge.

All as per item No 104 but FRLSH copper stranded cable of size 2.5 sq mm for 3/6 pin socket outlet 15 amp on one independent board. alongwith all fitting and accessories complete all as specified and as directed.

Material and Labour for point wiring complete with 1.5 sq.mm single core PVC insulated but unsheathed multistranded copper conductor FRLSH cable 1100 Volts grade drawn through in and including PVC casing caping of required size with all fittings and accessories alongwith green colour FRLSH Copper conductor cable of size 1.5 sq.mm as earth lead for one light point controlled by two, two way switch and connected to earth dolly PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealled box for mounting of switch, regulators or bell push and casing caping terminal box for mounting ceiling rose/ holders etc incl dismentling taking down old unserviceable point wiring and making good to disturbed complete all as specified and as directed.

Material and labour for sub main wiring with two single core PVC insulated multi stranded FRLSH Copper conductor cable of size 4.0 sq.mm drawn through in and including PVC casing caping of size with all accesories and one single core green colour FRLSH Copper conductor cable of size 4 sqmm as earth wire and connected to earth dolly and making good to disturbed surfaces complete all as specified and as directed. NOTE:- Two runs of cable with one run of earth wire and one run of casing capping will be measured as one unit (RM))

Material and labour for sub main wiring with two single core PVC insulated multi stranded FRLSH Copper conductor cable of size 6.0 sqmm drawn through in and including PVC conduit with all accesories and one single core green colour FRLSH Copper conductor cable of size 6.0 sqmm as earth wire and connected to earth dolly and making good to disturbed surfaces complete all as specified and as directed. NOTE:- Two runs of cable with one run of earth wire and one run of casing capping will be measured as one unit (RM))

Supply and fix 5 Amps switch Piano flush type single pole one way all as specified and as directed by Engr-in-Charge.

Supply and fix 5 Amp switch piano type single pole two way all as specified and directed by Engr-in-Charge.

Supply and fix bell push piano type one way 240 volt. all as specified and directed by Engr-in-Charge.

Supply and fix lamp holder of PVC/ Polycarbonate type with back plate all as specified and directed by Engr-in-Charge.

Supply and fix socket flush type 6 Amps, 5 pin, 230 volts all as specified and directed by Engr-in-Charge.

Supply and fix switch socket combination multipurpose 2-in-1 flush type 3 pin 16 amps and 3 pin 6 amps, 230v all as specified and directed by Engr-in-Charge.

Supply and fix ceiling rose surface bakelite three terminal all as specified and directed by Engr-in-Charge.

Supply and fix bell electric AC 240 volt, 50 Hz all as specified and directed by Engr-in-Charge.

Supply and fix flush type electronic fan regulator with 5 step type, 240 Volts AC, 50 Hz complete all as specified and directed by Engr-in-Charge. Make - Anchor or equivalent

Supply and fix sheet metal enclosure SPN 08 way (MCB DB) double door, 240 Volts AC all as specified and directed by Engr-in-Charge.

Supply and fix MCB, SPN (double pole) 32 Amps, 240 Volts, 10 KA ‘’C” curve all as specified and directed by Engr-in-Charge.

Supply and fix MCB, single pole, 5 to 32 Amps, 240 Volts, 10 KA breaking cap, ‘’C” curve all as specified and directed by Engr-in-Charge.

Supply and fix LED light batten 20 watt, 4 feet AC, PF-0.95 (min), sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work and retail spaces with three core flexible copper conductor cable from ceiling rose complete all as specified and directed by Engr-in-Charge. MAKE :- Wipro cat part No-LL20-221-XXX-65AL1 and techno commercially equivalent in CG/Philips/Havells

Supply and fix LED Light batten 10 watt, 2 feet AC, PF-0.95 (min), sleek and seamless profiled extruded polycarbonate batten with an efficient diffuser to illuminate work and retail spaces with three core flexible copper conductor cable from ceiling rose complete all as specified and directed by Engr-in-Charge. MAKE :- Wipro cat part No-LL20-111-XXX-65NE3 and techno commercially equivalent in CG/Philips/Havells

Supply and fix LED lamp 12 watt, CDL, B-22 (Pin type), 230V, PF-0.95 (min) all as specified and directed by Engr-in-Charge. MAKE :- Wipro/Philips/Havells

Supply and fix LED lamp 9 watt, CDL, E-27 230V, PF-0.95 (min) all as specified and directed by Engr-in-Charge.Make- Wipro/Philips/Havells . MAKE :- Wipro/Philips/Havells

Supply and fixing LED street light fitting 20 Watt with lens, 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-Charge. MAKE :- Wipro/Philips/Havells

Supply and fix LED building security light 35 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sq.mm three core copper flexible conductor cable, One GI medium grade 20mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS clamps and fasteners all as specified and directed by Engr-in-Charge. MAKE :- CG Cat Part No LSTS-20-CDL-M or techno commerciallyequivalent in Philips/Bajaj/wipro

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engr-in-Charge. MAKE :- Usha / Havells/CG NOTE :- Old UNSV ceiling fan deposit to MES store

Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.0 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engr-in-Charge. NOTE :- Old UNSV ceiling fan deposit to MES store

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers incl making of suitable hole in brick / stone wall for fixing of Exhust Fan complete all as directed by Engineer-in-charge. MAKE :- Usha/Bajaj/CG NOTE :- Old UNSV Exhaust fan deposit to MES store

Material and labour for Earthing complete with galvanised steel pipe electrode, 40 mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified bldg), connected with galvanised steel earthing lead of 4mm dia all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2with RCC precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia MS rod, funnel, wiremesh, 15 mm dia light grade GI tubing for protection of GI wire 4mm dia, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion.

Supply and fix MCB DB double door 4 way ETPN with 200 Amps rated bus bar 240 volts completed all as specified and directed by Engr-in-Charge.

Supply and fix MCB TPN 40-63 Amps, 415 volt 10 KA completed all as specified and directed by Engr-in-Charge.

Supply and fix outdoor distribution panel box CPRI type tested, fabricated from ISO certified factory of overall size 750 mm (L) x 400 mm (B) x 1500 mm (H) made with 3 mm thick CRCA sheet with hinged door front & rear for each cabinet, total 3 cabinet, powder coated by post office red and bottom black after anti-rust treatment of CRCA sheet, top cabinet with incoming 3ph & N aluminium busbar of size 40x10mm chamber, middle cabinet for mounting including MCCB 3 pole 125 Amps - 1 No and for 3ph & N distribution aluminium busbar of of size 30x6mm and side cabinet for incoming cable tray. 2 Nos earth terminal, door lock for front and rear door with additional external locing arrangement, Door handle for each front & rear door, mounting stand made with ISA 40x6mm and 500mm long leg, duly painted with one coat of black bituminous paint , LT Danger notice board at front and rear. One MCCB of 25 KA, 125 amps, 3 pole between incoming and outgoing busbar as mentioned above and 2 Set of aluminium busbar as mentioned above with size. (Contd,,....136)

(Contd from,,..135) NOTE :- (i) The FPB shall be errected after dismentling taking out old unserviceable one. (ii) Disconnection of all cables from old FPB and reconnection of all cables to new FPB shall be done and rate shall be inclusive of the quoted rate. (iii) Panel shall be CPRI type tested and to be fabricated in ISO certified panel manufacturing factory MAKE :- Success Engineers, Bhosari or equivalent CPRI approved makes.

Supply, laying and testing in repairs cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cable (heavy duty )1100 volts grade with stranded aluminium conductor of size 3.5 core 120 sq.mm omplete all as specified and directed.

Supply, laying and testing in repair cable XLPE insulated screened pvc bedded galvanised steel strip or wire armoured electric power cable (heavy duty )1100 volts grade with stranded aluminium conductor of size 4core 25 sq.mm omplete all as specified and directed.

Supply, laying and testing in repair UG cable, XLPE insulated, screened, PVC bedded galvanised steel strip or wire, armoured, electric power cable (heavy duty) with stranded aluminium conductor, 1100 volts grade of size 16 sqmm 4 core including taking down the existing unserviceable cable complete all as specified and directed.

Material and labour for fine stone dust for cousioning of UG cable/ at cable trenches complete all as specified and directed. NOTE :- Punned thickness of sand shall only be measured.

Material and labour for brick protection with sub class 'B' bricks of old size for UG cable complete all as specified and directed.

Material and labour for road cutting upto 300mm deep and 200mm wide for crossing GI water pipe line through road including making good the disturbed surface by filling mass concrete complete all as specified and directed. NOTE :- filling of mass concrete shall be measured and paid seperately.

Supply, lay and testing in repairs 25mm bore medium grade galvanized pipe with all fittings such as tee bends union elbow reducer etc laid in trenches/fixed to walls/floors, ceilings complete all as specified and as directed.

Supply, lay and testing in repairs 20mm bore medium grade galvanized pipe with all fitting such as tee bends union elbow reducer etc laid in trenches/fixed to walls/floors, ceilings complete all as specified and directed.

Supply and fix in repairs 25mm bore gun metal gate valve, cast screwed down, High pressure with iron wheel handle, Screwed both ends for iron pipe or unions complete all as specified and directed.

Cutting existing 25 to 32mm bore steel tubing for alteration or additions (each cut measured) including earth work and accessories like dummy plug union socket etc in any condition complete all as specified and directed.

V.R.PRAJAPATI AND CO.

MAHESH DADAJI BACHHAV

M/S JAYCONSTRUCTION CO

Aishwarya Constructions

S.R.M.K Enterprises