GE/DE-51/2019-2020

Amount

Demolition of cement concrete, unreinforced, in ground floors and pavings not exceeding 15cm thickness below or above ground level, complete all as specified and as directed.

Demolition of cement concrete, reinforced, of any type and in any position below or above ground level, complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, complete all as specified and as directed.

Dismantling of RCC Jalli and coping of any description and in position and unserviceable Jalli removed from site, complete all as specified and as directed.

Dismantling structural steel work including doors, gates, rafters, purlins etc. or similar works, but excluding framed truss etc., complete all as specified and as directed.

Dismantling posts or struts(wood, steel or RCC) any section including taking out embedded portion and making good disturbed ground, complete all as specified and as directed.

Dismantling of Barbed wire galvanised 2 strand of any type and at any place fixed to wooden members, complete all as specified and as directed.

Demolition of cement concrete, unreinforced, laid over roofs, floors (other than ground floors), staircases, landings and similar work, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc., to receive new plaster, complete all as specified and as directed.

Dismantling wall & ceiling boards (fibre, insulation etc ) or insulation boards, slabs, blankets any thickness including cover fillets, complete all as specified and as directed.

Demolition of Sign boards of any description, any size including Making good of site, complete all as specified and as directed.

Excavation in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 cum getting out, returning, filling in ramming earth or broken rubble in layers not exceeding 25 cm, watering and removing of surplus soil to a distance not exc 50m and making good surfaces, complete all as specified and as directed.

Excavation in trenches not exceeding 1.5mtr wide and not exceeding 1.5mtr deep and getting out complete in soft/loose soil, complete all as specified and as directed.

Returning, filling in, including spreading, leveling watering and well raming in layers not exceeding 25cms thick complete all as specified and as directed.

Removal of surplus soil to a distance not exceeding 50mtrs and depositing where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and as directed.

Hard core of gauge not exceeding 63mm stone aggregate, deposited, spread and levelled in layers not exceeding 15 cm thick watering and ramming to a true surface, complete all as specified and directed

Plain cement concrete 1:4:8, Type D-2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete all as specified and as directed.

Reinforced cement concrete 1:2:4 type B-1 as in slabs supported on walls, beams, column, in floors slabs, roofs, ladings, shelves etc., complete all as specified and as directed.

Providing precast reinforced cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate in louvers and jallies, 35 mm thick (measured solid), including all mouldings but excluding frame (precast frame shall be measured separately) set in cement mortar 1:4, complete all as specified and as directed.

PCC 1:2:4 type B-1 as in kerb stone, mud stops, copings, etc., and similar items including weathering, slightly rounded or chamfered angles and throating on top of chajjas, rails, cills etc., complete all as specified and as directed.

Providing precast cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate in copings (measured solid) 25cm wide, including all mouldings but excluding frame (precast frame shall be measured separately) set in cement mortar 1:4, complete all as specified and as directed.

Plain cement concrete 1:2:4, Type B-1 using 40mm graded crushed stone aggregate as in surface channels and drains, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner grith in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc., complete all as specified and directed.

Brick work with sub class “B” bricks straight or curved on plan exceeding 6mtr mean radius built in cement mortar 1:6 using old size bricks including demolition of brick work built in cement mortar including all quoins, arches, pillars etc., complete all as specified and as directed.

All as per description of Srl item No.-24 here-in-before but except bricks, complete all as specified and as directed.

Cutting holes in brick wall not exceeding half brick thick walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 (20mm graded crushed stone aggregate), complete all as specified and as directed.

15-18mm thick Udaipur Green Marble stone work (table rubbed and polished) in steps, shelves, and the like not less than 1Sqm (in one piece), including pointing in white cement 1:2 using marble dust with admixture of pigments to match with shade of stone, including moulding of edges, complete all as specified and as directed.

Labour only for moulding of ganite/green marble on one edge, as in steps, cooking platform and similar type of work, complete all as specified and as directed. (Note : Contract agency will be responsible for any damage during cutting and notching work.)

Use and waste of form work to soffits of suspended slabs, such as roof slabs, or similar work not exceeding 200mm thick for fair finished concrete surfaces, complete all as specified and as directed.

Formwork to edges of concrete flats, treads, break in floors, window cills, concrete railings, floor and roof n.exc 20 cm wide and side of RCC/ PCC band in walls, horizantal or sloping or similar work exc 10 cm but n. exc 20 cm wide for rough finished surfaces, complete all as specified and as directed.

10mm dia and above TMT bars cut to length, bend to shape as required including cranking, hooking ends & binding with mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

Mild steel work such as angle iron post , flat iron in fencing including cutting in reqd shape including welding with proper overlapping & Welding MS Plate with angle iron bottom as directed, drilling holes, notching for wire etc., embedded in concrete fixed vertically conforming to grade FE-290 E-165, complete all as specified and as directed.

10 mm dia steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other ends exceeding 10cm and not exceeding 15cm long, complete all as specified and as directed.

Supply only MS galvanised Chain link fencing (weight not exc 4 Kg/Sqm) any size or pattern as approved by GE complete all as specified and as directed by Engr-in-charge.

Steel gate Ornamental type/Grill work including hold fasts, pintels, stoppers running rails, bushes and all as CI decorative pieces, locking arrangement etc., complete all as per design approved by GE and as directed by Engr-in-charge work conforming to Fe-410-O.

Mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or othe connecting plates conforming to Fe 410-W (Gde-E-250) quality A, complete all as specified and as directed.

0.50mm thick prepainted galvalume aluminium zinc coated GI based semi corrugated/profile steel sheeting of any colour, having tensile strength of 550MPA as in roof covering, wall cladding with self tapping screws as per manufacturers instructions, including dismantling of plain or corrugated steel sheeting of any guge, complete all as specified and as directed.

2mm thick Fibre glass reinforced translucent colourd plain/lcorrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall,gate etc similar work, complete all as specified and as directed.

E-board 4mm thick self design type tiles ceiling on GI Powder coated channel/Tee/Grid of make (Armstrong or equivalent) including cutting holes to brick wall built in cement mortar & making good in cement mortar 1:3 or cement concrete 1:2:4 type B-0 as required frame work of following specification:- (a) Plugging to wall around the rooms & supplying & fixing GI Powder coated angle of size 25mm x 25mm x 1.0 mm (b) 1.60 mm dia GI wire suspenders with adjustable clamps including fixing to ceiling dash free fasterers (c) 25mm x 25mm x 1.5mm GI Powder coated tee as in main & cross members at 595mm c/c supported suspenders along with adjustable clamp to maintain level. ( d) E-board 4mm thick self design type ceiling tiles of size 595mm x 595mm confirming to relevant IS in squares fixed to GI Powder coated Tee with clips made to shape. Shade and pattern of 'E' board shall be as approved by GE, complete all as specified and as directed.

Pre-polished coloured chequered cement concrete tiles, factory made, Premium quality 300mm x 300mm x 25mm thick, set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors over 15 mm thick screed bed or bedding layer in cementy mortar 1:4, complete all as specified and as directed.

75mm thick PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate, as in sub base to receive topping layer finished even and rough, complete all as specified and as directed.

Vibro compacted Precast concrete interlocking paver blocks, factory made,any shape and size conforming to IS- 15658- 2006 of 60mm thick, M-35 Grade set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors laid over 30mm thick sand cushioning, complete all as specified and as directed.

Vibro compacted Precast concrete interlocking paver blocks, factory made,any shape and size conforming to IS- 15658- 2006 of 80mm thick, M-40 Grade set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors laid over 30mm thick sand cushioning, complete all as specified and as directed.

25mm thick PCC 1:2:4 type B-0 using 12.50mm graded crushed stone aggregate, as in sub base to receive topping layer finished even and rough, complete all as specified and as directed.

Wear proof topping 20mm thick (incorporating an approved metallic floor hardener) laid on concrete floors and pavings of 25mm thick in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate, over a sub base of 100mm thick PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate, topping to be finsihed even and smooth without using extra cement, complete all as specified and as directed.

Supply only metallic floor hardener, complete all as specified and as approved by GE.

Supply only Plastic dividing strips 22mm wide and 1.5mm thick , complete all as specified and as directed.

Rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 and finishing surfaces even and smooth without using extra cement, complete all as specified and as directed.

Screed bed or bedding layer in cement mortar (1:4) 15mm thick for laying floor finishes and finishing surfaces even and fair without using extra cement, complete all as specified and as directed.

Rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finishing surfaces even and fair in backing coat under wall tiles, complete all as specified and as directed.

Preparing newly plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and as directed.

Preparation of newly plastered or unplastered surface of walls and applying two coats of synthetic enamel paint over a coat of primer, complete all as specified and as directed.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint on surfaces of any description exceeding 10 cm width or girth over a coat of red oxide complete all as specified and as directed.

Stainless steel sign board both sides comprising of the followings:- (a) Two Nos of Stainless Steel Pipe 75mm Heavy gde of length 2100 mm incl top fancy cap and at bottom four no of anchors for embedding in PCC (b) Stainless Steel 25 mm Square Pipe frame of size 1200 mm x750 mm at one side welded butt and bright finished fixed to SS pipe with stainless steel Cup Head Screw of suitable Size. (c) Providing 2mm thick anodised aluminium sheet of size 1200mmx750mm fixed with ss scerw to SS Square tube complete. (d) Complete layering of any Colour retro reflective Poly carbonate trimethane sheet cut to shape and fixed over base plate as per IRC-67-1977 of any colour complete all as specified and directed. (e) Providing of 25mm wide retro reflective Poly carbonate white Bordar retro reflective Poly carbonate sheet all around complete. (f) Retro reflective Poly carbonate trimethane sheet letters / sign/arrow etc cut to shape and fixed over base plate as per IRC-67-1977 of any colour of 25mmx150mm (Widthxheight) complete all as specified and directed. Make 3M/gogiaplastic as approved by GE. Note – Location and sample of Sign board work shall be approved by GE.

Stainless steel sign board both sides comprising of the followings:- (a) Two Nos of Stainless Steel Pipe 100mm dia Heavy gde of length 4000mm incl top fancy cap and at bottom four no of anchors for embedding in PCC (b) Stainless Steel 50 mm Square Pipe frame of size 2500mm x1250 mm at one side welded butt and bright finished fixed to SS pipe with stainless steel Cup Head Screw of suitable Size. (c) Providing 2.00mm thick anodised aluminium sheet of size 2500mmx1250mm fixed with ss scerw to SS Square tube complete. (d) Complete layering of any Colour retro reflective Poly carbonate trimethane sheet cut to shape and fixed over base plate as per IRC-67-1977 of any colour complete all as specified and directed. (e) Providing of 50mm wide retro reflective Poly carbonate white Bordar retro reflective Poly carbonate sheet all around complete. (f) Retro reflective Poly carbonate trimethane sheet letters / sign/arrow/dash etc cut to shape and fixed over base plate as per sample of any colour of size 50 mm x300mm (Widthxheight) complete all as specified and directed. Make : 3M/gogiaplastic Note – Location and sample of Sign board work shall be approved by GE.

NOTE:- For minimum fair wages ,EPF and payment to labour employed, refer Sch A Note No-17,18 and Special Condition No 5 & 21.2 of this tender. Contractor must produce all the relevent record such as payment made to labour, EPF etc at the time of payment of RARs/Final bill. No payment will be released to contrator without producing the proper record.

NOTE:- Irrespective of whatever specified elsewhere in tender documents, all the debris/waste materials produced out of above mentioned work shall be removed out of Cantonement land and disposed off at locations notified by the Delhi Cantonment Board for disposal of waste building materials within NCR area, without any extra cost to Department under own arrangement of contractors. The rates quoted by the contractors against the items catered here-in-above in the BOQ are inclusive of said provision.

M/s Shubh Enterprises

Vipul Construction

A R construction

MAA SANTOSHI ENTERPRISES

imran construction company

The new hut furnitures

ASHUTOSH BUILDERS