Renovation Ladies and Gents Toilet in 5th and 6 th floor of kushkumar road admin building at Nungambakkam Chennai 34

Amount

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing white vitreous china water closet squatting pan (Indian type) including the required p or S trap

Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white P.V.C.10 litres capacity low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

Providing and fixing White vitreous china washbasin with fisher bolts including making all connections but excluding the cost of fittings.Flat back wash basin of size 550x400 mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with C.P. brass spreaders withbrass unions and G.I clamps complete, including painting of fittings and brackets,cutting and making good the walls and floors wherever required.

Removing and refixing the shaking existing washbasin/ urinals /sinks of any size including replacing damaged brakets / clamps cleats, bolts and nuts wooden plugs, etc complete as directed by teh E-in- charge

Providing and fixing white marble urinal partition 18mm thick of required size with required clamps screws etc complete, including rounding of edges all as directed by the engineer in charge

Providing and fixing CP brass spreader for urinal basin with necessary fixing arrangement etc., complete.

P/F PTMT waste coupling for urinal/ wash basin a.PTMT 31mm dia waste coupling

Providing and fixing uplasticised PVC connection pipe with brass unions : a. 15 mm nominal bore i. 45 cm length

P/F fiexible PVC waste pipe for sink or washbasin including PVC waste fittings complete. A. 32mm dia

P/F rectangular shape 600 X 450 mm mirror thickness of required shape and size with plastic moulded frame

Providing and fixing PTMT angle cock of approved quality and colour:

15mm nominal bore

Providing and fixing PTMT pillar cockof approved quality and colour:

15mm nominal bore

Providing and fixing PTMT long body bib cock of approved quality and colour:

15mm nominal bore

Providing and fixing PVC floor trap of approved quality a.100mm dia inlet

Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes, having thermal stability for hot &cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work Exposed on wall

20mm nominal outer dia pipes.

Providing and fixing unplasticised rigid PVCpipe of pressure class 6kg/sqcm to IS grade(Finolex/ Trubore or equivalent)including cutting and jointing pipes withsolvent cement solution etc. complete.

110 mm dia.

75 mm dia.

Providing and fixing unplasticised PVC mouldedfittings and accessories for unplasticised rigid PVCpipes including jointing with solvent cement etc complete.

Single TEE with door 110 x 110x 110 mm

Single TEE with door 75 x 75 x 75 mm

bend 110mm

bend 75mm

Providing and fixing GI special clamp for 75mm dia PVC pipe

Half brick masonry with F.P.S. bricks of class designation 50 in superstructure above plinth level upto floor V level in Cement mortar 1 : 4 (1 cement : 4 coarse sand)

12 mm cement plaster of mix: 1:6 (1 cement : 6 M fine sand)

15 mm cement plaster of mix: 1:6 (1 cement : 6 M fine sand)

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing factory made panel PVC doorshutter consisting of frame made out of M.S.tubesof 19 gauge thickness and size of 19mm x 19mmfor styles and 15x15mm for top & bottom rails.M.S. frame shall havea coat of steel primers ofapproved make and manufacture . M.S. framecovered with 5mm thick heat moulded PVC 'C'channel of size 30mm thickness, 70mm width outofwhich 50mm shall be flat and 20mm shall betapered in 45 degree angle on either sideforming styles; and 5mm thick, 95mm widePVCsheet out of which 75mm shall be flat and 20mmshall be tapered in 45 degree on the inner side to form top and bottom rail and115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on innerside, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer’s specification &drawing

Altering the PVC / wooden door by dismantling and refixing the shutter after making necessary altertion in door shutter frame , panel etc. complete all as directed by the Engineer in Charge.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing ISI marked anodised aluminium handles conforming to IS standards with necessary screws etc. complete

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and laying antiskid Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily etc complete.

Providing and laying glazed Ceramic glazed wall tiles of size 300x450 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Deep cleaning of toilet block of area 50 sqm of floor area with high quality rapid action tile cleaner and degreasing solution for tile and ceramic including cleaning of wall tiles , wash basin , urinals , WC, aluminiumm / glazed windows ventilators etc complete inside thre toilet block as directed by engineer in charge

White washing with lime to give an even shade :a. two or more coats

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: a.one or more coats

Dismantling white vitreous china water closet squatting pan (Indian type) including p or S trap