Gopalchak-Talla Road from 6.800 Km to 16.500 Km - Strengthening (with DBM, BC) work in the District of Purba Medinipur

Part - A (Road work) Cold Milling Cold Milling of Bituminous Pavement surface upto the required depth by mechanical means using milling machine, without disturbing the under lying layers, to proper line and level, cleaning the surface properly after milling and removing the loose materials, stacking the milled materials for re-use, necessary guarding, barricading & lighting, including hire charges of machinery, cost of fuel and labour and other incidental charges all complete and as per direction of Engineer-in-Charge. a) For depth upto 100mm

Water Bound Macadam Sub Base Water Bound Macadam Sub Base by consolidating Jhama metal / Laterite chelly or stone metal / shingles of specific size in hard crust to requisite thickness (measured after compaction) in layers including screening of metals etc. as necessary, hand packing, sweeping, watering and rolling in stages with power roller to proper line, grade and camber, lighting, guarding & barricading and making necessary earthen bundh of one metre width on each side where necessary to protect edges and preparing the bed by necessary cutting or filling and rolling all complete including the cost of all materials and hire and labour charges of all men and machineries and compacting to the required density, as per Clause 404 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). (i) For Construction of Sub Base by consolidating Jhama metal (63 mm to 45 mm) with moorum screening :

Tack Coat Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). i) On bituminous surface @ 0.25kg /sqm Using Cationic RS

ii) On Granular surface treated with primer @ 0.275 /sqm. Using Cationic RS

Dense Graded Bituminous Macadam Providing and laying dense graded bituminous macadam with 100-120 TPH batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder of approved grade @ 4.0% (min) for Grading -1 and 4.5% (min) for Grading -2 by weight of total mix and filler(Cement /hydrated lime / Rock dust ) as per table 500-10 and mix design done as per table 500- 11and job mix formula as per clause 505.3.3 transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C, and to achieve the desired compaction as per MORT&H specification clause No. 505.3.5 complete in all respects (Reference to MORT&H's specification clause 505). ii) For Grading 2 (26.5 mm nominal maximum aggregate size) Layer Thickness 50-75mm Using Pakur Variety Stone Materials

Bituminous Concrete Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder of approved grade@ 5.2% (min) for Gr.-1 & @ 5.4% (min) for Gr.-2 , as per table 500-17, and mix design done as per table 500-10 and job mix formula as per cl. 505.3.3 and filler(Cement /hydrated lime / Rock dust ), transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C to achieve the desired compaction as per clause no 507.3.5 complete in all respects ref. to MORTH specification clause No.507. i) For Grading-2 ( 13.2 mm nominal maximum aggregate size), Layer thickness:30-40mm Using Pakur Variety Stone Materials

Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical Specification (Reference to MORT&H's specification 2807). Note:- Add 2% of cost of materials( except the cost of wire mesh & Accelerator compound) for miscellaneous consumables, like nozzles, wire brush, cotton waste etc.

Painting Two Coats on NewConcrete Surfaces Painting two coats, after filling the surface & applying as ealing primer, with synthetic enamel paint in all shades on new plastered concrete surfaces as per MORT7H's specification 803.6.2.(Reference to MORT&H's specification 803).

Water Bound Macadam Providing, laying, spreading and compacting stone aggregates ofmspecific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density (Reference to MoRT&H's specification 404). 9A By Manual Means By salvage material

Part - B (Road Furniture) Retro-Reflectorised Traffic Signs Providing and fixing of retroreflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick,when signs with maximum side dimensions do not exceed 600mm, or with aluminium sheeting 2.0mm thick when signs with maximum side dimensions exceeds 600mm, supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (i) 90 cm equilateral triangle