RequiredExperience with Government
RequiredAnnual Turnover
RequiredOEM Annual Turnover Bid to RA enabled No Note: 1. OEM Turn Over Criteria: The minimum average annual financial turnover of the OEM of the offered product during the last three years
Requiredending on 31st March of the previous financial year
Requiredshould be as indicated in the bid document. Documentary evidence in the form of certified Audited Balance Sheets of relevant periods or a certificate from the Chartered Accountant/Cost Accountant indicating the turnover details for the relevant period shall be uploaded with the bid. In case the date of constitution/incorporation of the OEM is less than 3 year old
Requiredthe average turnover in respect of the completed financial years after the date of constitution shall be taken into account for this criteria. Analog Transceiver-Handheld ( 8 pieces ) Technical Specifications * As per GeM Category Specification 1/7 Specification Specification Name Values Bid Requirement (Allowed Values) PERFORMANCE FEATURES Frequency Range (MHz) 380-512 380-512
Required806-890 Types of Bandwidth UHF Full Band UHF Full Band Channel Capacity 128 76
Required128 Channel Spacing 12.5 * Frequency Spread without degradation in Tx/Rx Specification 5 * Frequency Stability (± ) 1.6 * Antenna Impedance 50 * TRANSMITTER RF Power output setting of transmitter Switchable * RF Power output Range 1 to 4 Watts (UHF) 1 to 4 Watts (UHF) Type of Emission 11K0F3 * Frequency deviation ± 2.5Khz max. for 100% at 1KHz * Modulation Sensitivity 1 to 10mV at 1 KHz at mic. Input for +/- 1.5 KHz standard deviation * Modulation Distortion 3 * Modulation Fidelity +1
Required-3 dB of 6dB octave pre-emphasis charactrestics from 350 Hz to 2700 Hz with 1KHz as reference * Spurious & Harmonics Suppression (dB) -70 * VSWR 1.5 * RECEIVERS Sensitivity at 12 dB SINAD 0.02 * Squelch Sensitivity of receiver 0.2 * Adjacent Channel Selectivity (dB) 70 * Image Rejection (dB) 68 * Audio Output
Required(with less than 5 % distortion at 1 KHz reference measured at specified AF output) 250
Required500 * Audio Response +1
Required-3 dB of 6dB octave de- emphasis charactrestics from 350 * 2/7 Hz to 2700 Hz with 1KHz as reference ACCESSORIES Antenna Helical Antenna * Programming kit No * Technical repairing & maintenance manual with complete block diagram
Requiredcircuit layout etc in soft as well as hard copy No * Battery charger Yes * Output voltage of the charger - * Battery charger suitable for Lithium-ion * Charging time for standard mode 6 to 14hrs * Charging time for rapid mode 1 tO 3 hrs * Number of spare batteries with each Radio Set 2 2 POWER SOURCE/BATTERY Chemistry of Battery Li-ion * Voltage rating of the Battery 7.4 * capacity of Battery (milli AH) 1800 * VARIOUS FEATURES Simple Press to talk yes * Protection against high VSWR yes * Low Battery Alert yes * CTCSS or DCS yes * Capable of VOX for hands-free operation Yes * PTT ID Encode Yes * Busy Channel Lockout Yes * Channel Scanning with call quieting facility Yes * Selective Call Decode Yes * Capable of being Killed Unkilled No * Emergency SOS/SIREN Yes * LCD Display (Min 4 characters) Yes * 3/7 Automatic Number Identification (ANI) Yes * Talk-around Yes * DTMF Keypad Yes * DTMF Microphone Yes * Keypad Lock Yes * Built-in GPS No * Battery Strength Bar Indicator or Digital Voltage read out Yes * Signaling 2Tone
Required5Tone * GENERIC Internal Speaker impedance 4 * External Speaker impedance 16 * Output Termination BNC female socket * Weight of Transceiver with Battery 280 * Other features - * SAFETY Protections Reverse polarity protection & short circuit protection * SERVICE Warranty 2 1
Required2
Required3
Required4
Required5 OPERATING CONDITION Minimum Operating temperature -10 * Maximum Operating temperature 55 * Minimum Storage temperature -40 * Maximum Storage temperature 70 * Humidity non- condensing (at +40 oC ) 95 * CERTIFICATION BIS registration under CRS of Meity for the battery - * BIS registration Number and Date for the Battery - * TEST REPORT DETAILS conformity to Dry Heat for 16 hrs at a maximum temp in accordance with IS:9 000/part-3/section-5 Yes Yes 4/7 1977 latest conformity to Cold Test for 4 hrs at a minimum temp in accordance with IS:9 000/part-2/section-4 1977 latest Yes Yes conformity to Damp Heat (Cyclic)Test for 2 Cycles of 24 h each at a temp of 40 degree C & 95% RH in accordance with I S:9000/part-5/sectio n-1/1991 latest Yes Yes Drop Test (in packed condition): IS 9000 Part VII/SEC
Required3/1979 (reaffirmed 2004): Six drops one on each face
RequiredHeight of fall 1000 mm incase of handheld items and 500 mm in case of other items Yes Yes Vibration Test: IS 9000 Part VIII/1981 (reaffirmed 2006): 12 hours
Required4 hours along with each axis
Requiredat 15-150 Hz and with amplitude of 0-15 mm/2g Yes Yes Storage Test: IS 9000 Part III/SEC 5/1977 & Part II/SEC 4/1977 (reaffirmed 2004): -40 deg C for 5 hours
Requiredthen raise the temperature to 70 deg C for 16 hours Yes Yes Bump Test: IS 9000 Part VII/SEC 2/1979 (reaffirmed 2004): 4000 bumps at peak acceleration of 400 m/s sq Yes Yes Availability of the test report from Central Govt/NABL ILAC accredited lab to prove conformity to the specification No Yes
RequiredNo 5/7 If yes test report to furnished
Requiredto the buyer on demand No * Test Report Number and date for the specification test - * Name and address of the Lab for the specification test - * * Specifications highlighted in bold are the Golden Parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer. Additional Specification Documents
