REPAIR MAINT TO SEWAGE LINE TANK CLEANING TOP CLEAR BLOCKAGE OF FLOOR TRAP WC MANHOLES SEPTIC TANK AND REPAIR TO TOILET SUNKEN FLOOR WATER PROOFING TREATMENT PLUMBING SANITARY FITTINGS IN ZONE B AREA AT GMS UNDER GE I GOS

Amount

Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring surface finished even and smooth without using extra cement to receive the topping layer complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 300 x 200 mm x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles including 10mm thick rendering in CM 1 :4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20mm thick screed bed in CM 1 :6 complete all as specified and directed.

All as per Item No.05 above but on vertical surfaces area of each tile exceeding 0.06 sq m but not exceeding 0.11 sqm as skirting complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , including 20mm thick screed bed in CM 1 :6 complete all as specified and directed.

All as per Item No.07 above but on vertical surfaces area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm as skirting complete all as specified and directed.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like 15mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Taking down existing water proofing membrance and cleaning roof, plastered surface etc preparing the surface to receive plaster by brushing with wire brush and fanning the surface to remove all loose dirt etc and brushing neat cement slurry @ 3.00 Kg/Sqm complete all as specified and directed.

M&L for rendering 15 mm thick surface as in roof with integral water proofing compound 3% by the weight of cement in cement mortar 1:4 complete all as specified & directed. (Note :Integral WPC will be measured and paid separately).

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in sub base flooring surface finished even and rough to receive the topping layer complete all as specified and directed.

M&L for water proofing treatment to roof surface complete all as specified and directed with the followings :- (a) Apply bituminous based primer confirming to IS: 3384-1965 @ 0.30 kg/sqm. (b) APP modified bituminous membrane 3mm thick with non woven polyester core of weight not less than 3.2 to 3.5 Kg/sqm laid and bonded to the sub strata by heat process, over laps of 100mm shall be sealed/fused by flame torch application as per manufacturer instructions. (c) Applying bituminous based aluminium paint @ 0.20 Kgs/Sqm in two coats over APP membrane

Demolition of cement concrete (un-reinforced) other than ground floor compelte all as specified and directed.

M&L for 30mm thick PCC 1:2:4 type B-0 using (12.5mm graded stone aggregate ) as in sunken floor mixed water proofing compound finished surface even and smooth with using extra cement complete all as specified and directed. Note : water proofing compound shall be measured seperatly.

M&L rendering 15mm thick cement plaster in cement mortar 1:3 as in brick/concrete surface of sunken portion using water proofing compound complete all as specified and directed. Note : water proofing compound shall be measured & paid seperately

M&L wire brushing and cleaning top surface of cement concrete including flashings and junction of parapet etc. and surface painting with a layers of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq.m. blinded with grit or pea size gravel @ 0.006 cu.m. per sqm and lightly tampered (area of flashings, etc., shall be added to the roof area) complete all as specified and directed.

M&L Cement concrete 1:5:10 type E2 using 40mm graded stone concrete as in sunken floor, foundations, filling and mass-concrete finished surface fair and even complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Demolition of cement concrete unreinforced in ground floor and paving exc 15cm thick (below or above ground level) complete all as specified and directed.

M&L moorum / red bajri filling in floors or pavings laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L Hardcore of broken stone or boulder of guage n.exc 63 mm, deposited, spreed and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L 100 mm thick Cement concrete 1:3:6 type C-2, using 40 mm graded crushed stone aggreates as in flooring finished even and fair complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 using 40 mm graded stone aggregates as in hard standing 100 mm thick laid in panels and finished even and smooth without using extra cement and spike rolling to surfaces or making impression of expanded metal whilst the concrete surface is green complete all as specified and directed.

M&L chequered cement concrete tiles 250 mm X 250 mm X 20-22mmthick, set , jointed and pointed in neat cement surry in floors with pigments including 20 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for sand cushioning including spreading in layers and rolled consolidated to thickness of 50 mm (minimum) for receiving precast PCC interlocking blocks complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size fixing with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4, type B-0 using 12.50mm graded crushed aggregates as in floor surface complete all as specified and directed.

M&L Screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and directed.

S&F vitrified ceramic tiles 10mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L rendering 10mm thick in CM 1:4 to wall as a backing coat to dados complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350X250X7mm / 450X350X7mm thick coloured designed tiles Set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per Item No. 34 above but on vertical surface such as skirtings, matching to the floor complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L Brick work with subclass 'B' bricks straight or curved on plan to any radius half brick thick wall built in CM 1:4 complete all as specified and directed.

M&L rendering 15mm thick in CM 1:6 to on fair faces of brick work or concrete surface finished even and smooth with out using extra cement complete all as specified and directed.

Mild steel TMT bars 10mm and over, cut to length bend to shape required incl cranking bending and binding with mild steel wire (annealed) not less than 0.9 mm dia. complete all as specified and directed.

M&L Precast RCC 1:2:4 type B1 using 20mm graded stone aggregates in cover slabs set in cement mortar 1:4 including all necessary form work complete all as specified and directed. (Note : Reinforcement shall be measured and paid separately).

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate, as in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 Type B-2 using 40mm graded stone aggregate in pavement/hard-standing laid in alternative panels, surface finished even and smooth without using extra cement, including necessary form work, complete all as specified and directed.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

M&L for vitreous china wash basin, white,flat back, size 550 x 400 mm with brackets, including supply & fixing pillar cock 15 mm bore CP fancy type, PVC connection of 450 mm long, PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as sapecified and directed.

S&F in repair viterious china squatting pan orissa pattern size 580x440mm white integal foot rest & including 10 lit cap flushing cistern PVC low level & flush pipe including concrete bedding & including P trap 100mm complete all as specified and directed.

M&L for Vitreous China urinals, bowl type flat back size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement etc complete all as sapecified and directed.

S & F in repair, vitreous china wash down water closet pan (pedestal pattern), white, 'P' or 'S' type, inc. 10 litres, PVC flushing cistern, L L, white, with inlet,ball valve, float & brackets, inc. flush pipe, PVC tube 32mm dia. & inc. plastic water closet seat, black, closed pattern with flat bottem, & cover & M S CP or aluminium hinging device, complete all as specified and directed.

S&F PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, PVC connection 15mm dia etc complete all as specified and directed.

S&F health faucet with fluxi pipe and hand shover ,the length of hose 1.50mt fitted to the tap.complete all as specified and directed.

S&F in repair EWC seat cover of any pattern including cover and Mild steel chromium plated hinging devices of any colour complete all as specified and directed.

Taking up or down 15 mm bore GI steel tubing and connections including cleaning if refixing required complete all as specified and directed.

Taking up or down 20 mm bore GI steel tubing and connections including cleaning if refixing required complete all as specified and directed.

Taking up or down 25 mm bore GI steel tubing and connections including cleaning if refixing required complete all as specified and directed.

S&F 15 mm bore GI tubes medium grade (ISI marked) with all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F 20 mm bore GI tubes medium grade (ISI marked) with all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F 25 mm bore GI tubes medium grade (ISI marked) with all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

Refixing 15 mm bore old steel tubing and connections in new or old position (wall, floor, ceiling etc) complete all as specified and directed.

Refixing 20 mm bore old steel tubing and connections in new or old position (wall, floor, ceiling etc) complete all as specified and directed.

Refixing 25 mm bore old steel tubing and connections in new or old position (wall, floor, ceiling etc) complete all as specified and directed.

Dismantling water tanks of any description, capacity exc 500 and not exc 1000 litres and removing from site complete all as specified and directed.

Dismantling water tanks of any description, capacity exc 1000 and not exc 2000 litres and removing from site complete all as specified and directed.

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position complete all as specified and directed.

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top)1000 litre capacity hoisted and fixed in position complete all as specified and directed.

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top)2000 litre capacity hoisted and fixed in position complete all as specified and directed.

S&F in repairs 20 mm bore Ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair 25 mm bore Ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repairs 20 mm bore Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs 25 mm bore Gun metal globe or gate valves with iron wheel head screwed both ends (ISI marked) for iron pipe complete all as specified and directed.

S&F in repairs for 15mm bore of pipe pillar taps cast copper alloy, with capstan head chromium plated fancy type screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs 15 mm bore stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle chromium plated fancy type screwed both ends for iron pipe or for unions complete all as specified and directed.

Cleaning and removing all scale and dirt etc from tank and from mouths of circulating pipes etc of tank capacity exc 500 litres and not exc 1000 litres complete all as specified and directed.

Cleaning and removing all scale and dirt etc from tank and from mouths of circulating pipes etc of tank capacity exc 1000 litres and not exc 2000 litres complete all as specified and directed.

S&F in repair 15 mm bore bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type chromium plated complete all as specified and directed.

S&F in repair 15 mm bore brass elbows both ends screwed and fixed complete all as specified and directed.

S&F in repair 20 mm bore brass elbows both ends screwed and fixed complete all as specified and directed.

S&F in repair 15 mm dia brass union to connect iron to polyethylene and fixed complete all as specified and directed.

S&F in repair 20 mm dia brass union to connect iron to polyethylene and fixed complete all as specified and directed.

S&F in repairs 125 mm bore Grating doom with waste hole of PTMT Minimum weight 40 gms complete all as specified and directed.

S&F in repairs 125 mm brass chromium plated shower rose with or without swivel joint complete all as specified and directed.

S&F CP 2 way bib cock. complete all as specified and directed.

S & F in repairs Lid/cover of water tank capacity of 1000/500Ltrs including necessary cleats/clamps complete all as specified and directed.

S&F SS toilet paper holder with flap complete all as specified and directed.

S&F in repairs Waste fittings 32 mm dia, brass, chromium plated for sinks/basins etc with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 100 mm internal dia of pipe complete all as specified and directed.

M&L for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified and directed.

M&L for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius with out access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius with out access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC 75 mm bore (SWR) vent cowl complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats(Minimum weight 90 gms) complete all as specified and directed.

S&F towel rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190 gms) complete all as specified and directed.

S&F swivel shower of PTMT any colour for fixing with 15 mm pipe (minimum weight 40 gms) complete all as specified and directed.

S&F waste coupling of PTMT for 40 mm bore of pipe half or full threaded (minimum weight 60 gms) complete all as specified and directed.

S&F soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed

S&F CP Wall mixture complete all as specified and directed.

S&F glass shelf assembly consisting of 5.5mm thick sheet 12cm wide with chromium plated bracket guard railing 60cm long complete all as specified and directed.

S&F cornner glass shelf of size 9"*9" shelf and frond,circle in design fixed over chromium plated brackets of heavy duty with frond linings with glass fixed in wall with necessary screws complete all as specified and directed.

S&F stack clamps made out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nut and securing ends of stays to wall or roof for 50 mm bore of pipe complete all as specified and directed.

S&F CP Angular stop cock 15mm complete all as specified and directed.

S&F health faucet with fluxi pipe and hand shover ,the length of hose 1mtr fitted to the tap complete all as specified and directed.

S&F cornner glass shelf of size 9"*9" shelf and frond,circle in design fixed over chromium plated brackets of heavy duty with frond linings with glass fixed in wall with necessary screws complete all as specified and directed.

S & F in repairs, vitreous china wash basin, white, flat back, size 550x400mm with brackets, inc. cutting for & pinning in ends of brackets, inc. waste fitting, PTMT 32mm dia and pillar taps of PTMT 15mm dia complete all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, of 450mm length complete all as specified and directed.

Taking down aluminium door and windows of any size and of any description built in wall and making good at disturbed surface with cement mortar 1:4 and applying two coats of plastic emulsion paint as per existing treatment complete all as specified and directed.

S&F anodised glazed side hung door shutters with anodised aluminium frame of section of 100x44x2mm and bottom rail of 44.5x99x1.8mm including 5.5mm thick tinted sheet glass ordinary quality with all necessary suitable push & pull plate/handle , screw, jointing cleats, rubber packing aluminium snap beading and 1 No 200mm long Aluminium tower bolt, 100mm long 3 No Aluminium butt hinges B-21 Type and one No mortice brass lock 100 size 4 leaver (Vertical Type) with 01 No door closer Aluminium (Diie cast) body hydraullically regulated designation ;No 02 universal type, for each shutters (Door shall be size approx 1.2mx2.1 in single leaf) complete all as specified and directed.

S&F aluminium anodised galzed hung type window shutters made out from anodised aluminium frame of 'H' section size 34.00x43.5x2mm thick with 4mm tinted sheet galss (Weight not less than 0.57 kg/RM and shutter 'Z' of size 34.00x43.5x28.00mm having thickness 2.00mm (Wt not less than 0.50kg/RM) and all necessary jointing cleats , glazing, clips rubber packing, aluminium snap beading Tower bolt 100mm long 1 No and sliding hinges 180mm longs including aluminium grill with Mosquito proofing etc complete all as specified and directed.

M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

Dismantling of wall and ceiling boards(fibre,pulp,insulation,etc)or insulation boards/slabs/blankets,any thickness,including cover fillets. complete alll as specified and directed.

M&L 12 mm thick Seamless calcium silicate ceiling made out of 1800 x 1200mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillips head with under head cutter at 200mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed.

M&L for Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling size of grid 605 mm X605 mm complete all as specified and directed.

M&L for applying one coat of Altec putty finish to obtain smooth fnished ceiling surfaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of plastic emolition paint complete all as specified and directed.

Taking down rolling shutters of any size complete all as specified and directed.

Supply and fixing of steel rolling shutters as per IS-6248-1979, made of required size MS laths interlocked together through their entire length and jointed together at the ends by end locks mounted on shafts (50 mm dia) heavy duty, thickness of lathe 1.20mm, grade II springs, guide channel 3.15mm thick, bottom plate 3.15mm thick gear oprated shutter with bevel gear box and crank handle, hood cover 1.20mm and 1 coat of red oxide primer including necessary concrete bed blocks with PCC 1:3:6 of size wall width x 150mm x300 mm and finishing with plaster 15mm thick in CM 1:4 finished even and smooth complete all as specified and directed.

S&F ball bearing suitable for rolling shutter complete all as specified and directed.

S&F safety lever locks with four levers for rolling shutters complete all as specified and directed.

S & F MS pipe 50 to 125 mm dia as shaft including two coats of aluminum paint over a coat of red oxide primer complete all as specifed and directed.

Supply and fixing following parts of steel rolling shutters (a) Gear Box Set general.

(b) Guide channel 3" (3.15 mm)

(c) Bottom plate 5" (2.25mm)

Greasing and servicing only to existing rolling shutters complete area of shutter n exc 20 Sqm each.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Excavation in any type of soil for post holes (or similar holes) each not exceeding 0.50 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

S&F rolled mild steel section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plates of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

Dismantling of AC corrugated / semi corrugated sheet as in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Moulding as in cornices, picture rails and the like exc 13 & n.exc 25 sqcm Fillet wrought complete all as specified and directed.

M&L 12 MM thick Plywood, grade BWP, type BB fixed with screws to timber frame work complete all as specified and directed.

M & L 1.5mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions complete all as specified and directed.

M & L 1 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions complete all as specified and directed.

M & L for 25mm dia Stainless Steel Curtain Rod fancy type complete all as specified and directed.

M & L for Brackets, Ends Cap and Holder suitable for 25mm dia Stainless Steel Curtain Rod fancy type complete all as specified and directed.

M&L washing,rubbing down and stopping of distempered and painted surfaces on wall and applying alkali resistant priming paint complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coat of weather proof exterior emultion (APEX of Asian paint or equivalent) complete all as specified and directed.

M&L for preparation of old treated surfaces of wall by complete removing of existing treatment and applying two coat of oil bound distemper over a coat of 1 mm thick wall putty and primer complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 Sqm on plan and not exceeding 1.5 m depth in soft /loose soil etc complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 Sqm on plan and exceeding 1.5 m but not exceeding 3.0 m depth in soft /loose soil etc complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 150 mm internal dia of pipe complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 200 mm internal dia of pipe complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for salt glazed stoneware (SGSW) drain pipes laid in trenches of 150 mm internal dia of pipe and jointed in CM 1:1 complete all as specified and directed.

M&L for salt glazed stoneware (SGSW) drain pipes laid in trenches of 200 mm internal dia of pipe and jointed in CM 1:1 complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 200 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

Returning filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil etc complete all as specified and directed.

Removal of excavated materials not exceeding 50 m and depositing where directed complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removal of rubbish from site complete all as specified and directed.

Mild Steel TMT bar 6 to 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Cleaning and removing all blocked scale and dirt, etc, from manholes/traps/gully traps/tanks from mouths of circulating pipes, etc. including Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Cleaning of sewage line including manholes of any dia by roding and flushing after cleaning and removing mud/sludge etc to a distance exc. 250m but n.exc 500m and spreading in low laying areas and covering with loose soil complete all as specified and directed. Note:- Length shall be measured through out the manhole

M&L for cutting and removing wild bushes/ vegetation, surface dressing around the septic tank/sock well/ manholes to a distance of 2 mtrs and along sewage line all around and depositing surplus spoil/ rubbish exc 100M but n.exc 500 M complete all as specified and directed.

M&L for removing of sludge from septic tanks including removal of sludge water manually or mechanically in all respect and removing the sludge to distance not exceeding 500 mtrs and burried in to the ground and making to a true surface and covering with loose soil complete all as specified and directed. (Note :The rate included excavation and filling )

M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

Cutting of bituminous road to the width and depth required for laying SWG pipe or sewage line including hacking , benching and including making good to top surface of road with bitumen & aggregate as per road specification complete all as specified and directed.

S&F in repair NP2 pipe laid and joineted ,with cooller 200 mm dia complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for walling of random rubble uncoursed stone masonry, well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

All as per Item No. 165 above but except stone

Hammer dressing to RR masonry wall (granite basalt/trap stone) uncoursed with maximum depresion of 40 mm from straight edge held against the surface (for area to be pointed) complete all as specified and directed.

M&L for keyed pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:4 complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 40 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, coping, benching, bed block, lintel band, plinth courses etc and similar work including weathering,slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

M&L Brick work using fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for providing precast cement concrete louvres and jallies 35 mm thick (measured solid) including all mouldings but excluding frame in cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregates and set in cement mortar 1:4 complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surface of wall in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed .

M&L for preparation of newly plastered surfaces of walls and applying three coat of white wash complete all as specified and directed.

S&F in repairs PVC waste pipe for urinal/WHB/sink complete all as specified and directed.

S&F plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Taking down of eaves gutters and rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

M/S JAGANNATH SASMAL

R K Traders

HARAGOURI SUPPLIERS

DHABALESWAR ENGINEERING WORKS

V.Venkata Ramaiah

G.KRISHNA MURTHY AND PARTNERS

Likitha Enterprises