PROVISION OF PARKING SHED AT MO PBR AND ADDN ALTN TO NC3I TP ROOM COMMAND HQ UNDER GE HADDO SRI VIJAYA PURAM UNDER GE HADDO SRI VIJAYA PURAM

Amount

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and as directed

M&L Reinforced cement concrete (nominal mix) Type B1 1:2:4 20 mm graded aggregate inWalls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses in Walls, retaining walls,basement walls, ballast walls and the like; anythickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed

M&L for form work to faces of walls retaining walls, abutments, parapets, drain walls and like for flat rough finishesd surface all as specified

Excavation over areas, n exc 1.5m deep and getting out in hard / dense soil complete all as specified.

Removing excavated material (any type of soil) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in hard dense soil complete all as specified and as directed.

M & L for hardcore of gauge n exc 63 mm deposited spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface of broken stone or boulders complete all as specified and as directed.

M & L for providing 100 mm thick, PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base of floors complete all as specified and as directed.

M&L for providing 50mm thick cement concrete 1:2:4 type B2 (Using 20mm graded stone aggregate) as in floor/paving etc including finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L for chequered cement concrete tiles of size 30cm X 30cm X 25mm thick with grey cement and pigments set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor over and including 20mm thick screed bed in CM 1:4 complete all as specified and directed

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed withearth around, in layers not exceeding 25 cm in hard/dense soil complete all as specified and as directed.

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed

M&L for reinforced precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in landings, drain cover, cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary form work, set in CM 1:4 complete all as specified and directed (Note : Reinforcement shall be measured and paid for separately)

S & F MS Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate as in filling, foundation and mass concrete complete all as specified and as directed.

M& L for precast cement concrete block masonry with solid blocks using PCC 1:3:6, type C1(using 20mm graded stoneaggregate), exc. 10cm in width, set in CM 1:6 complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces finished with even and smooth without using extra cement in CM 1:4 complete all as specified and as directed.

Material & Labour for preparing newly plastered wall surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

M & L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified and as directed.

S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins, pole where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates using structural steel of Fe-410W (Gde E-250 quality A) complete all as specified and as directed.

S & F Mild Steel work in tubular trusses and tubular posts/ purlins including special shaped washers etc., complete using ERW or induction butt welded tubes conforming to IS :1161-1979 grade st-240 including notching, drilling, fitting, riveting and/or welding or connecting with bed plate, bolt and nuts complete all as specified and as directed.

S&F mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

M & L for preparing of new of previously untreated steel surface of any description, not otherwise described, over 10 cm width or girth applyig two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M & L aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for vitrified ceramic tiles light shade 10mm thick (square/ rectangular) polished, area of each tiles exc 0.42 Sqm but n. exc 1 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed

M&L for vitrified ceramic tiles light shade 10mm thick (square/ rectangular) polished, area of each tiles exc 0.42 Sqm but n. exc 1 Sqm as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 to recieve tiles complete all as specified and directed

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M&L for 10mm thick plaster in CM 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth complete all as specified and directed

M&L for applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth after complete removal of existing treatment complete all as specified and directed

M&L for 10mm thick plaster in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered ceiling surface and applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty complete all as specified and directed

M&L for applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty on ceiling after complete removal of existing treatment complete all as specified and directed

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed

S&F for anodized aluminum snap grid frame work for false ceiling incl hangers 6mm dia, GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and as directed

M&L for 12mm thick perforated particle board/tiles for insulation and acoustic purposes of size 60x60cm fixed with screws to timber frame or with staples on aluminium snap grid including preparation of surface with two coat of oil bound distemper over a coat of chalk whiting primer complete all as specified and as directed

S&F door closer hydraulically regulated aluminium (die cast) body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified

Dismantling wood boarding, panels, beams or any description, fixed any position with nailscomplete all as specified and as directed.

M&L for 18mm thick designed rubco hut rubber wood frame shutter for cupboard, WHB counter cupboard, wall and finished with two coats of melamine polish with asian sealer and wood filler over a coat of honey/natural colour wood filler putty for dust free surface etc including preparation and applying three types of sand papers and surface finish to a glossy/ mat finish to match with the adjoining surface complete all as specified and as directed. Make of Rubber Wood members : RUBCO/ India Wood or equivalant

Taking down shutter of any description exc 1 Sqm but n. exc 2 sqm each complete all as specified and directed

M&L for 30mm thick rubber wood superior quality, chemically pressure treated, egde glued, finger jointed, tongued, grooved as in door shutter and finished with two coats of melamine polish with asian sealer and wood filler over a coat of honey/natural colour wood filler putty for dust free surface etc including preparation and applying three types of sand papers and surface finish to a glossy/ mat finish to match with the adjoining surface complete all as specified and as directed. Make of Rubber Wood members : RUBCO/ India Wood or equivalant

S&F 100mm size butt hinges, extruded brass, with mild steel hinge pin, bright polished type B-11 complete all as specified and as directed.

S&F 200mm size brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and as directed.

S&F 150mm size brass handles, cast type, polished bright complete all as specified and as directed.

S&F 100mm brass 4 levers mortice lock, vertical type complete all as specified and as directed.

S&F 250mm brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and as directed.

M&L precast cement concrete block masonry exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:4 all as specified

M&L for Point wiring two single core 1.5 sqmm size PVC insulated, unsheathed FRLSH multistranded copper conductor cable and one single core 1.5 sqmm size green colour PVC insulated FRLS multistranded copper conductor cable as earth continuity conductor, 1100 volt grade (with proper colour coding Red/Blue/yellow for phase, black for neutral and green for earth) complete drawn through and including PVC casing and caping not less than 25 mm width with all fittings, surface on wall/roof /floor including including sunk pressed steel terminal boxes flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete in making good the existing surface with existing colour coding as required at site complete all as specified for the following :- Note :- The unit rate quoted shall deemed to include the cost of following :- (a) GI metal flush box of minimum thickness of 1.6mm and modular cover plate with frame of any module complete. (b) Proper colour coding is to be followed as per IS specification. (c) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (d) Cutting chases in wall/floor /beam/ceiling to be concealed conduit and making good the disturbed surfaces.

All as per item No 52 above, but, for two light point controlled by one switch 5 Amps one way.

S & F for switch modular type, 6 Amps 1 module, 230 volts AC circuit complete all as specified and directed.

S & F and testing Tube light fittings LED 22 watts 4 feet including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make: Luker Cat Part No : LT522 or equivalent to CG or equivalent in Philips Havells

S & F SPN DB sheet metal enclosure double door suitable (IP-43) Protection 4 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete all as specified and as directed.

Supply & fixing MCB SPN 32 Amps (`C’ series) having current rating 10 KA complete all as specified and as directed .

Supply & fixing MCB single pole, 6 to 32 Amps (`C’ series) having current rating 10 KA complete all as specified and directed. Note for item No 56 to 57:- All copper conductors should be connected with MCB alongwith copper reducer terminals of suitable size duly crimpled.”

Supply, laying,testing and commissioning of LT XLPE insulated, armoured heavy duty electric aluminium conductor cable 1100 Volts grade of cross section 16 Sqmm 2 core (laid on floor/Roof/wall in proper saddling all as specified and directed. Make : Polycab/ Gloster/Havells/ Finolex

Supply and laying/fixing in trenches, cable ducts ,clamping on wall or any place DWC HDPE pipe of size 50 mm(OD) x 38mm (ID) along with connected accessories like couplers.bends,end caps etc. for LT cable protection all as specified and directed. Make: Rex Poly Extrusion Ltd/ Tirupati Plastomatics Pvt Ltd/ Prince/Jain Irrigation Systems Ltd

Taking down copper/aluminium point wiring(light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials and making good disturbed surfaces of walls, floors, etc.complete all as specified and as directed .

Taking down old aluminium sub main wiring of any size complete all as specified and as directed .

Taking down fuse Unit/DBs 415 Volt/230 Volt complete all as specified and as directed .

M & L point wiring complete with 1100 volts grade, 1.5 sq.mm (nominal area), single core, FRLSH PVC insulated ,unsheathed, multi stranded copper conductor cable drawn through and including medium grade, rigid , non-metallic PVC concealed/ on surface conduit of size not less than 20 mm dia, with all necessary fittings, concealed in walls/ floor or surface on wall/ roof duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth duly including suitable size of factory made fabricated MS sheet modular terminal box, flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete in making good the existing surface with existing colour coding as required at site complete all as specified for the following :- Note :- The unit rate quoted shall deemed to include the cost of following :- (a) GI metal flush box of minimum thickness of 1.6mm and modular cover plate with frame of any module complete. (b) Proper colour coding is to be followed as per IS specification. (c) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (d) Cutting chases in wall/floor /beam/ceiling to be concealed conduit and making good the disturbed surfaces.

All as per Srl item No 63 above, but, One light/fan point controlled by one switch 5 Amps one way.

All as per item Sl No 63 above, but , for two light point controlled by one switch 5 Amps one way complete all as specified and directed.

All as per Srl item No 63 above, but, point wiring for 3 pin switch socket outlet , 6 Amps on independent board.

All as per Srl item No 63 above, but, point wiring for 3 pin switch socket outlet , 6 Amps on same board .

All as per item No. 63 above, but , point wiring with two single core 4.0 sqmm size cables and one 4.0 sqmm green colour cable as earth continuity conductor for one 6 pin 16 Amps socket out let on independent board.

S & F for switch modular type, 6 Amps 1 module, 230 volts AC circuit complete all as specified and directed.

S & F Switch modular type , single pole one way 15 amps all as directed.

S & F for socket outlet modular type 1 way 6 Amps, 3 pin, 230 volts AC circuit complete all as specified and directed.

S & F Socket outlet 2 in 1 modular type, 3 pin, 6 and 16 Amp , universal complete all as specified and directed.

S & F stepped type modular electronic fan regulator on the existing phenolic laminated sheet/ new modular plate etc. as reqd complete all as specified.

S & F BLDC 5 star rated ceiling fan metallic body ISI marked 1200 mm sweep, 220V AC, 50 Hz with all accessories alogwith providing and connecting up with 1.0 sqmm 3 core flexible copper conductor of suitable length from connector of fan to ceiling rose and testing complete all as specified and as directed by Engr In charge. Make: Usha , Model No TECHNIX or equivalent to CG / Havells/ Orient

S & F and testing LED recessed mounted 2' x 2' LED luminarie alongwith driver THD<10%, fulllGlow G6 of cap 42 watt, size 2 x 2 Ft with longer life and less maintenance including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make: Philips model no RC380B LED42S-6500 G6 L60W60 PSU OD S1 or equivalent to CG/ Havells/ Luker

Supply and fixing of Decorative ultra slim linear LED lighting fixture of 18 Watt recess mounted 220V , 50Hz with Aluminium housing ,environmental friendly energy efficient fitting recess mounted round/square in shape, not less than 105lm/watt (Warm white/ white colour as per requirement of site complete) complete all as specified and directed. Make - Luker Cat Part No. LNPRL8 or equivalent make in CG/Havels /Philips. NOTE: The rate quoted deemed to include for any alterations required to existing false ceiling as per site condition for fixing light fitting.

S & F Sub main wiring with PVC insulated FRLS cable 2 run of single core 6 sq mm 1100 V grade with stranded copper conductor cable using proper colour coding Phase Red/Yellow/ Blue, Neutral- black and earth- green in and incl rigid PVC conduit concealed/ surface in wall, surface on wall (ISI marked) incl all specials like joint elbow, Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 10.0 sq mm for earth continuity complete all as specified and as directed .

S & F Sub main wiring with PVC insulated cable 2 run of single core 4 sq mm 1100 V grade with stranded copper conductor cable using proper colour coding Phase Red/Yellow/Blue, Neutral- black and earth- green in and incl rigid PVC conduit concealed in wall/ on surface on wall (ISI marked) incl all specials like joint elbow, Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 4.0 sq mm for earth continuity all as directed. Note for item No 73 & 74 : 3 length of cable and one length casing caping shall be measured and paid for one length.

Supply & fix Modular AC Box With 20A DP MCB "C' Type, Metal Enclosure & Unbreakable Heavy Duty With ISI Plug Top, 240 volts AC supply for air conditioner, flush mounting in the wall complete all as specified and directed. Make:- Anchor (Roma) model no 98492 or equivalent

Taking down carefully existing split type air conditoner of any make,type, size and any tonnage keep in safe custody of contractor and painting the outer area and re-fixing the same after charging of gas, adding new copper pipe line as required at its location after completion of work all as directed.

Taking down carefully existing speaker of any make,type, size and any Amps keep in safe custody of contractor and painting the outer area and re-fixing the same its location after completion of work all as directed.

Taking down carefully existing smoke/heat detector of any make,type, size keep in safe custody of contractor and painting the outer area and re-fixing the same its location after completion of work all as directed.

S & F DB VTPN sheet metal enclosure double door IP 53 protection, door earth suitable for incoming upto MCCB 100 Amps/125 Amps & outgoing MCB TP / SP. Triple pole and neutral 415 V 6 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete and making good to the distrubed surface /walls complete all as specified and directed.

S & F single pole and neutral sheet steel powder coated Distribution board IP -43 protection with door earthing for MCBs fitted with 200 Amps rated bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 12 ways and making good to the distrubed surface /walls complete all as specified and directed.

S & F in replacement of MCCB, 3 pole, 100 Amps, 50Hz, 25KA rupturing capacity, 415 Volts adjustable type with thermal and magnetic release alongwith copper separator terminalscomplete all as specified and as directed.

Supplying & fixing MCB SPN 40 Amps (`C’ series) having current rating 10 KA complete all as specified and directed.

Supply and fixing with wall, piller, wooden structure etc. uPVC Panel Trunking of size 60 mm (H) x 60 mm (W) for running of wire, cable of any type etc complete all as specified and directed by Engr In charge.

M & L Cutting channels, grooves or rebates n exc 15 cm girth, and trimming surface with or without reinforcement all as specified and as directed by Engineer-in- Charge.

Earthing complete with galvanised earth plate electrode 60 cm x 60 cm x 6.15 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 MM Dia as earthling lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. RCC cover with frame etc including necessary excavation in any type of strata , returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion. NOTES: 1) The unit rate shall also include for earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover 50mm thick reinforced with TMT bars 8mm dia @ 100mm c/c both ways, funnel with watering pipe 20mm dia medium grade, GI protection pipe light grade 40mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (notes) under sub-heading earthing, specified on Sl. Page Nos. 451 & 452 of SSR Part-II. 2) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

ISLAND SALES ENTERPRISES (BID ID -3366237)

M/s K Moorthi (BID ID -3365728)

CARTWHEEL CONSTRUCTION (BID ID -3364800)

SHUBHAM SHANKAR GAIKWAD (BID ID -3365788)

M/s Prem Enterprise (BID ID -3367082)

ABR Construction (BID ID -3364248)

Sree Tirumala Enterprises (BID ID -3363715)

M/s Ramesh Lal (BID ID -3365917)