REPAIRS TO SEEPAGE LEAKAGE AND INTERNAL EXTERNAL PLASTERING OF CERTAIN BLDGS AT SI LINES UNDER GE BHOPAL

Amount

Notes - (i) Application of oil bound distemper, exterior/interior emulsion paints, etc shall be carried out using roller brush of approved quality only. (ii) Mixing of oil bound distemper, exterior/interior emulsion paints, etc shall be carried out with mechanical mixture/strieer. (iii) Surface shall be allowed to dry completely before application of any paint. Wet or newly plastered surfaces with visible moisture shall not be painted till it is dry. (iv) Removal of existing treatment shall vbe carried out through mechanical scrapper, etc so that the surface in not damaged. (v) The rate quoted against BOQ are including neccessary scafolding expenses upto triple storey building.

Preparation of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and M&L for applying one coat of white wash on walls complete all as specified and directed.

All as per BOQ Serial item No.1.10 above but on ceiling complete all as specified and directed.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, and applying two coats of oil emulsion distemper, white or tinted over one coat of white cement based putty (where required) all as specified and directed. Note - (i) Cement Putty shall be measured and paid separetely. (ii) Complete removal of existing surface to be carried out using mechanical scrappers and wiped clean with cotton cloth so that no dust/loose particles remain on the surface complete as directed by Engineer-in-charge. (iii) Hairline cracks upto 3 mm thickness shall be filled with crack seal of M/s Asian Paint or equivalent as approved; quoted rate is deemed to include for this aspect.

Preparation of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and M&L for applying one coat of oil emulsion distemper, white or tinted complete all as specified and directed.

Preparation of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and M&L for applying one coat of cement based paint, white or tinted complete all as specified and directed.

All as per BOQ Serial item No.5.00 above but two coats of cement base paint complete all as specified and directed.

M&L for preparing old painted surfaces of wood and wood based materials of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing old painted steel & iron surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with putty and preparation of surfaces for further treatment and M&L for applying two coats of exterior acrylic emulsion weather coat paint, white or tinted complete all as specified and directed. [Make:- ACE or M/s Asian Paints or WALL MASTA of M/s Berger or equivalent in M/s Shalimar as approved by GE] [NOTE:- 3mm thick wall care cement putty where ever required shall be measured & paid separately.]

Preparation of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and M&L for applying one coat of exterior weather proof water base emulsion paint on wall all as specified and directed. [MAKE : ASIAN (ACE) /SHALIMAR (SAKTIMAN) /BURGER (WALL MASTA) as approved by GE]

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, and M&L for applying two coats of interior plastic imulsion paint, white or tinted over and including one coat of white cement based putty (where required) complete all as specified and directed. Note - (i) Cement Putty shall be measured and paid separetely. (ii) Complete removal of existing surface to be carried out using mechanical scrappers and wiped clean with cotton cloth so that no dust/loose particles remain on the surface complete as directed by Engineer-in-charge. (iii) Hairline cracks upto 3 mm thickness are to be filled with crack seal of M/s Asian Paint or equivalent as approved; quoted rate is deemed to include forthis aspect.

Preparation of old decorated surfaces of wall including brooming, scraping down smoke spot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks by filling cement putty and applying one coat of interior plastic emulsion paint, white or tinted complete all as specified and directed.

All as per BOQ Serial item No.12.00 above but on ceiling complete all as specified and directed.

M&L for French polishing on surfaces of wood and wood based materials of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with one or more coats complete all as specified and directed.

M&L for applying 3mm thick wall care putty complete all as specified and directed. Make: BIRLA/JK]

M&L for cleaning & drying thoroughly existing surface of walls, roofs, chajjas, etc for all foreign matters such as fungus, moss, dust, etc by wire brushing and dusting; applying two coats of polymer modified cementations based protective & water proofing coating as per manufacturers instruction complete all as specified and directed. [MAKE: ACROCOAT / FOSROC or equivalent as approved by GE]

M/L rendering 15 mm thick cement mortar on brick/stone surfaces or surfaces other than fair faces of brick work in cement mortar 1:4, even and smooth finish without using extra cement, in patches including taking down existing plaster complete all as specified and directed.

M/L rendering 10mm thick on fair faces concrete surfaces with cement mortar 1:3 on ceiling even and smooth finish in patches including taking down existing plaster complete all as specified and directed.

M/L rendering 15 mm thick cement mortar on brick/ stone surfaces or surfaces other than fair faces of brick work in cement mortar 1:6 in small patches area not exceeding 3.0 Sqm each including taking down existing plaster complete all as specified and directed.

M&L for rendering 15mm thick in two layers, first layer (rendering coat) of 10mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces and second coat (finishing coat) of 5mm thick in cement mortar 1 : 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished even and smooth without using extra cement including taking down existing plaster complete all as specified and directed.

M/L rendering 10 mm thick cement mortar on brick/ stone surfaces or surfaces other than fair faces of brick work in cement mortar 1:6 complete all as specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) to buildings with synthetic enamel paint, n.exc. 150mm long and 20mm wide in words & figures (e.g. P-1, P-27, T-123, T-81/2, etc) over black synthetic enamel painted back ground of n.exc.300mm dia including obliterating old writing of any description n exc 0.10 sqm with paint to match existing work complete all as specified and directed. Note - "P-1", "P-27", "T-123", "T-81/2", etc shall be considered as one unit for measurement purpose.

Taking down plants/vegetable growth, etc (upto 10cm girth), from buildings walls, parapets by cutting/chiseling fully without disturbing structure upto height of 10.00m from average ground level at different locations and cleaning the surfaces neatly with wire brush to remove dust and other foreign particles and applying hydorochloric acid (HCL) on left over root portion and making good the disturbed surfaces in cement mortar 1:4 complete all as specified and as directed.

M&L for crack filling with approved crack filling compound (Crack seal of M/s Asian Paint or equivalent in Pidilite), crack thickness more than 3 mm; including opening of cracks, cleaning, and necessary scaffolding suitable for height upto 10.00 mtr from ground level complete all as specified and as directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed. [MAKE: ACCOPROOF/WATER SEAL/MC BOUCHAMIE, MUMBAI/FOSROC/CICO/PIDILITE as approved by GE]

S&F Chicken wire mesh, mild steel 12mm mesh size and 0.56mm dia of wire fixed to walls with nails, etc complete all as specified and directed.

M&L for ShaliCryl ® 215 single component, UV resistant, unique elastomeric, high build exterior waterproofing coating based on a revolutionary acrylic polymer with quick-set capabilities to resist moisture attack applied in following sequence complete all as specified and directed.:- (a) Surface Preparation :- Remove all loose and foreign materials, if any, by a wash with a jet of air / water. Fill voids and undulation area with Polymer Mortar made out of ShaliSBR Latex, Water, Cement and Sand in the Ratio of 1:1:5:12.5. Fill cracks up to 3 mm with PlastiSeal and cracks over 3 mm with PlastiSeal P after opening the crack to a “V” cut. In case of any poor plaster surface in existence (for old building), remove the same and corrected with new cement : sand mortar in the ratio of 1 : 4 admixed with ShaliPlast LW+ @ 200 ml / bag of cement. (b) Primer Application :- Apply ShaliPrime WB as Primer after dilution with potable water in the ratio 1:0.5 for a theoretical Coverage 8-10 sqm per Ltr of the mix and allow it to dry for 3 to 4 hrs. post elimination of undulation, roughness of concrete, joint marks, Voids and any other surface correction. (c) Application of Material:- Apply first coat of ShaliCryl® 215 over the primed surface @ 160 ml per Sqm. Add maximum of 10% potable water by volume for the first coat only, if required, to have brushable consistency only. Allow the applied coating to dry 6 to 8 hrs of application. Apply second coat of ShaliCryl® 215 without dilution over dried first coat @ 140 ml per Sqm and allow it to dry. Do not undertake any further work over the coated area within 72 hrs of final coat. A coat of 100 micron of ShaliCryl TC 100 will improve water / dust repellent property. NOTE:- (i) Work shall be carried out by the authorised applicator of the manufacturer. Necessary documentary evidence in support of the authorised applicator will be submitted to Engineer-in-charge before the commencement of water proofing work. (ii) The quoted rates is deemed to include for the cost of scaffolding, T&P, etc required for execution of the work.

Demolition and breaking up drain pipes (SGSW, AC or RCC) of any diameter, set in cement mortar including fittings complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, 110mm bore including clamps complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, 75mm bore including clamps complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors, 110mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors, 75mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) junction double (double T), equal or unequal, 110mm bore complete all as specified and directed.

S&F PVC (SWR) junction double (double T), equal or unequal, 75mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl, 75mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110mm bore complete all as specified and directed.

Preparing new plastered or un-plastered surfaces of wall and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer complete all as specified and directed. [NOTE:- 3mm thick wall care cement putty where ever required shall be measured & paid separately.]

Preparing new plastered or un-plastered surfaces of wall and M&L for applying two coats of exterior acrylic emulsion paint, white or tinted over and including a coat of exterior wall primer on plastered surfaces complete all as specified and directed. [Make:- Ace Paint of M/s Asian Paints or equivalent in M/s Berger or M/s ICI as approved by GE]

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and directed.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc under 40 Sqcm in section, in unframed work in any position complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL as approved by GE]

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in ridges, etc, fixed with & including self tapping screws complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL as approved by GE]

S&F Asbestos cement 6mm thick, corrugated or semi corrugated sheets in roofs, walls etc, fixed with L or J type or cranked hook bolts complete all as specified and directed.

Fixing only Asbestos cement 6mm thick, corrugated or semi corrugated sheets in roofs, walls etc, fixed with new L or J type or cranked hook bolts complete all as specified and directed. NOTE:-Old serviceable sheets obtained from dismantling shall be reused.

S&F Asbestos cement 6mm thick two piece serrated ridge for corrugated or semi corrugated sheets, fixed with L or J type or cranked hook bolts complete all as specified and directed.

S&F Fibre glass reinforced translucent corrugated sheeting, 2mm thick, with two corrugation side lap fixed with L or J type or cranked hook bolts or with & including self tapping screws on angle frame in roof, wall etc complete all as specified and directed.

S&F Steel work in tubular/structural trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for Cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in 25mm thick sub floors, leveling course, etc finished even & rough complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3; cutting exceeding half brick but not exceeding one brick complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks (Modular), straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

S&F in repairs decorative mild steel chromium plated, 19mm dia, minimum thickness 1mm, curtain rod with side fixing brackets, rings & decorative knobs complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Refixing shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each in the same opening after taking down, easing and adjusting including refixing builders hardware as required and renewal of unserviceable screws complete all as specified and directed.

Refixing shutters of any description not exceeding 1 Sqm each in the same opening after taking down, easing and adjusting including refixing builders hardware as required and renewal of unserviceable screws complete all as specified and directed.

Schedule of credit (calculation will be done off line) Rs.11,180.00

RAJPATI CONSTRUCTION

Vee kay construction

Jyoti enterprises

S Balwinder Singh