SPECIAL REPAIR TO BLOCK NO 151 OF NCO QTRS AND PROVN OF INTER LOCKING TILES IN OPEN GYM OF SAINIK INSTITUTE AND CERTAIN MINOR WORK AT NDA KHADAKWASLA

Amount

Dismantling floor, hearth or wall / stone slabs and tiles of any description or thickness in floors tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed.

Demolition of brick/ block masonry built in Cement mortar complete all as directed

Demolition of cement concrete in ground floor & pavings n exc 15cm thick (below or above ground level) including cleaning off the premises complete all as directed

Demolition of reinforced cement Concrete of any description and in any position not other specially provided for complete all as directed

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as directed

M&L for glazed coloured joint free ceramic tiles 250X350X7mm hick/300x450x7mm thick on vertical surfaces such as skirting/ dado laid over and including 15 mm thick backing coat in CM (1:3) set and jointed in neat cement slurry and pointed in white or coloured cement to match. As specified by Engineer in charge.

M&L for coioured Non skid joint free Ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as directed

M&L for joint free Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as directed

M&L for 20 mm thick Granite (of any type) tiles machine cut in cooking platform skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing of type incl 15 mm thick screed bed or bedding layer in CM (1:6) complete all as directed.

M&L for machine cut cuddapa stone slab 35 to 40mm thick over cement screed base ,laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete all as directed

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base ,laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete including & over 20mm thick screed bed in CM 1:6 complete all as directed

M&L for glossy finish machine pressed precast conctete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade incl 30mm thick sand chusioning complete all as directed

Ditto all as per item No. 12 above but using old interlocking obtained from dismantled and serviceable tiles complete all as specified and directed

M&L for rough dressed sahabad stone slab flooring (30 mm thick) incl bedded and jointed in cement mortar (1:6) and pointed in CM (1:3) complete all as specified and directed

M&L for cement concrete type D- 2, (1:4:8) (Using 40mm graded stone aggregate) as in sub base of 75mm thick complete all as directed.

M&L for cement concrete type C- 2, (1:3:6) (Using 40mm graded stone aggregate) 75 mm thick as in plinth protection incl complete all as directed

M&L for precast cement concrete (1:3:6) type C-1 (Using 20mm graded stone aggregate ) block masonry with solid blocks exc10 cm thick in width and setting in cement mortar (1:6) complete in wall complete all as specified.

M&L for precast cement concrete block masonry with solid blocks of PCC (1:3:6) Type C1 n. exc 10 cm in width and setting in cement mortar (1:4) complete all as directed

M&L for reinforced cement concrete (1:2:4) type B1 (Using 20 mm gradred stone aggregate) as in lintel /beam cantilevers all as specified and directed

M&L for formwork to sides and soffits of floor or roof beam ,beam haunching girders bressumers lintels cantilevers shelves including supports overhangs etc also splays between floor and beams etc

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as directed

Ditto all as per item No. 21 above but 6 to 8 mm dia for stirrups all as directed

S & F TMT bars 6 to 8 mm dia cut to length bent to shape required includig cranking, bending etc & binding with ms wires (annealed) n. exe 0.9mm dia complete all as directed.

Cutting holes into or through stone masonry walls built in cement mortar and making good in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required superficial area n.exc 150 Sq cm

Drilling holes for bolts, pipes, etc.n. exc 25mm dia

Rounding /moulding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situation.

M&L for racking out joints work built in cement mortar to random or polygonal rubble uncoursed or brought upto course and flush pointing in CM (1:4) in floor complete all as directed

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even & smooth without using extra cement complete all as directed

M&L for rendering 5 mm thick in CM (1:3) on concrete surfaces finished even and smooth without using extra cement for ceiling complete all as directed

Taking down chowkhats or frame not exc 1.5 sqm each with shutters (without taking off shutters from the frames)

Taking down shutter of any description n exc 1 sqm each

Taking down shutter of any description n exc 2.0 sqm each

S&F steel ventilator with centre top hung shutter including hinges, steel peg stay, complete

Hacking out old broken glass(any thickness, size, quality or discription) from wooden frames or stone, concrete or brick surrounds , glazed with putty or fixed with beads complete all as directed

S & F factory made solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with but 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2 mm prelam PVC Sheet on back face supplying & fixing in frame at site as per specification & drawing complete all as directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F second class hard wood (sal wood) Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and incl fixed hold fasts (split at one end) complete all as directed

S&F 30 mm thick 2nd class hardwood skelten shutter glazed and skelton open rebated and prepared to receive glass with divided into squares with plain chamfered or rounded mitered and rebated sash bars any nubmers fitted with cut and mitered beads for securing glass size of members of windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b)

S&F 35mm thick Factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

M&L for 35 mm thick Factory made II nd class hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) supplied and fitted to chowkats complete all as directed.

S&F second class hardwood small fitting such as door & windows stops incl all necessary labours articles n.exc 200cu.cm each

S&F Sheet glass 3 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane

S&F 4mm thick Figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples .

M&L for 75mm long butt hinges cold rolled mild steel medium weight and fixed

M&L for 100mm butt hinges cold rolled mild steel medium weight and fixed

S&F 100mm Aluminium handles, cast type, anodised

S&F 150mm Aluminium handles, cast type, anodised

M&L for Aluminium anodised barrel tower bolts of extruded section 100mm long

S&F for Aluminium anodised, barrel tower bolts 150mm long of ex- truded section and fixed

S&F 200 mm long aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections all as specified and directed

M&L for mild steel 300 mm long sliding door bolts plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as directed

S&F for 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed.

M&L for preparation of new wooden surfaces and painting two coats of Synthetic Enamel paint over a coat of pink primer exc 10 cm width or girth of any description

S&F Harrison curtain rails (25mm dia), powder coated fancy type anodised aluminium alloy with fixing brackets, stops, rollers etc complete all as specified and directed.

S & F fancy type powder coated MS bracket for curtan rod suitable for fixing curtain rod at middle portion & at one side of wall portion.

M&L for aluminium anodised Tubular towel rail 20mm dia (For CB)

S & F brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges

S & F steel plate rack of size of size not less than 750 X 250 X 900 mm made from stainless steel pipe section & steel bars suitable for hanging/fixing to wall.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. if required reconnecting and re-fixing in position. Capacity of tank upto 500 litres.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered, *ISI marked" hoisted and fixed in position all 500 ltr capacity as specified in SSR Part I

Taking down up or down steel tubing and connections incl cleaning for re-fixing or removal to stores ,15mm dia pipes complete all as specified and directed.

Ditto all as per item No. 63 above but 20mm dia pipes.

M&L for Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors 15mm bore of pipes complete all as directed

Ditto all as per item No. 65 above but but 20mm dia pipes.

Refixing of old serviceable 15 mm bore of steel tubing pipe take out from item above with new fitting and conection in new or old position on wall, cieling, floor etc complete all as specified and directed.

Ditto all as per item No. 67 above but 20mm dia pipes take out from item above

S&F for 20mm dia tank Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm-45gms /25mm- 65gms) complete all as specified & directed.

S&F in repair Ball valves 15mm dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210gms./ 25mm-455gms/ 40mm - 690 gms) including taking down old one complete all as specified and directed.

S&F in repairs fancy type Bib taps 15mm dia, chromium plated , cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed including complete all as specified and directed.

S&F in repairs Stop valves 15mm dia, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions one complete all as specified and directed

S&F 15mm bore in repair fancy type Pillar taps, chromium plated, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as directed.

M&L Vitreous China wash basin, white, flat back, size 550x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as directed.

S & F PVC connections 15mm size with PTMT nuts of length 450mm

S&F for Brass chromium plated shower rose 125mm size complete as directed and sample to be approved by Engr-in-charge.

S&F in repairs for PVC flushing cistern valve less, syphonic action type low level, ball valve, float and handle with bracket of 10 ltrs capacity all as specified and directed.

S&F for Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern including necessary cutting to floor tiles and connection to WC complete all as specified and directed

M&L for unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe 50mm bore of pipes complete all as directed

S&F in repair stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever castiron brackets, connecting union etc. overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as directed

S&F in repair Water closet (Squatt pattern) vitreous China squatting pan, ‘Orissa’ pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) connection to trap and squatting pan including P' trap set in and including concrete etc. complete all as specified and direted including making good to floor

S&F Soap dish any type fixed to plugs with chromium plated brass screws minimum size 160x160x90mm

Excavation in trenches n. exe 1.5m wide & n. exe 1.5m depth for foundation etc n.exe 10sqm on plan and getting out in.Soft/Loose soil

Excavation in trenches n. exe 1.5m wide & n. exe 1.5m depth for foundation etc n.exe 10sqm on plan and getting out in Hard/Dense soil

Returning filling in including spreading levelling, watering & well ramming in layers n. exe 25cm

Removing excavated material any type of Soil n. exe 50m and depositing where directed at a level n. exe 1.50m above the starting point in

Dismantling of cast iron 100 mm bore pipes jointed in cement motar

Dismantling of cast iron 75 mm bore pipes jointed in cement motar complete all as directed

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor complete all as directed

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor complete all as directed

S&F in repair for 75mm bore dia PVC (SWR) bends with access door complete all as directed.

S&F in repair for 75mm dia PVC (SWR) branch piece single(single Y) equal or unequal with access door complete all as specified and directed

S&F in repair for 110mm bore dia PVC (SWR) bends with access door complete all as directed.

S&F in repair for 110mm dia PVC (SWR) branch piece single(single Y) equal or unequal with access door complete all as specified and directed

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed

Demolition & breaking up drain pipes( SWG, AC or RCC pipes) set in cement mortar 100mm dia

Demolition and breaking up drain pipes ( SWG,AC or RCC pipes ) set in CM 150mm dia.

M & L for providing bed to drain pipes 75mm dia in cement concrete (1:3:6) type C2 using 40mm graded stone aggregate including packing under & haunching against the sides of pipes after they are laid & tested complete all as directed

M & L for providing bed to drain pipes 100mm dia in cement concrete (1:3:6) type C2 using 40mm graded stone aggregate including packing under & haunching against the sides of pipes after they are laid & tested complete all as directed

Ditto all as per item No. 99 above above but for 150mm dia pipes

M & L for providing reinforced cement concrete pipes 100mm dia class NP 2 with collars laid and jointed with cement jointed all as directed

Ditto all as per item No 101 above but 150mm dia pipes

Cutting into existing manholes for connecting new drains internal dia of pipe 100mm making good to pipe & rendering cutting out existing benching for forming branch channel (1/2 round or 3/4 section in cement concrete (1:2:4) type B-1, smooth finished complete all as directed

Ditto all as per item No. 103 above but for 150mm dia of pipe

S&F for Stack clamps for 100mm bore of pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

M & L for providing precast RCC (1:2:4) type B1 (Using 20mm grade stone aggregate) as in cover slabs for manholes set in CM (1:6) complete all as directed ( Note : Reinforcement shall be measured & paid separately)

M&L for rendering 10mm thick on fair faces of brick or block or cement surfaces in cement mortar (1:4) finishing even & smooth without using extra cement mixed with WPC.(Note: WPC shall be measured and paid separately)

M&L for rendering 15mm thick on other than fair faces of brick or stone masonry surfaces in CM (1:4) finishing even & smooth without using exta cement

Supply only Integral water proofing compound

M & L for providing plain cement concrete (1:3:6) type C2 (Using 40mm grade stoe agg) as in foundation filling and mass concrete

M & L for providing plain cement concrete (1:2:4) type B1 (Using 20mm grade stone agg) as in surfaces channels & drains

M & L for providing plain cement concrete (1:2:4) type B1 (Using 20mm grade stone agg) as in bed plates, roof kerbs coping including weathering slightly, rounded or chamfered angles and throating and necessary use and waste of form work complete all as directed

Dismantling of single layer of manglore/ Similar pattern tiles in roofing complete all as directed.

Dismantling of battens of tiles of any size and description spaced exc 15 cm, including tiling fillets complete all as directed.

Dismantling of unframed wk timber scantlings 40 sq. cm and over in section, in any position

Ditto as per item item No. 115 above but in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

S&F galvanised corrugated mild steel sheeting 0.63mm thick with two corrugations side lap, fixed with 'L' type or 'J' type of cranked hook in lieu of screws and washers in roofs, walls etc with grade of zinc coating 275.

Ditto all as per item No. 118 above but using old serviceable sheets all as specified and directed

M&L for wrought second class hardwood in scantlings, to replace old and decayed timber (including piecing, scarfing, etc., of old and new timbers if required) and removing defective portions to store complete all as directed.

M&L for clean sawn second class hardwood tile battens at 30cm centres, exe 5 and n.exe 15 sqcm sectional area complete all as specified.

Ditto all as item item No. 121 above, but except battens

M&L for preparing tile battens of any size and spacing and treated all over (measured overall on one side only spaces not deducted) with two coats of cresoting oil etc specified and directed

M&L for providing roof tiles Manglore pattern interlocking at side joints, laid dry, complete all as specified.

Ditto all as item No. 124 above, but except tiles

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in CM (1:6) complete all as directed

Ditto all as item No 126 above, but except tiles

S&F eves boards clean sawn second class hardwood in roof 20mm thick

M&L for complete removal of existing water proofing treatment of any decription and layers from wall,roof,chajja's,gabble walls, edges (at any height )etc incl any number of screed bed or bedding layer of mortar if any complete and cleaning the surface free from dust and mud ,scrubbing down with water complete all as specified , cleaning off the premises all as directed

M&L for rendering 10mm thick in cement mortar 1:3 on concrete surfaces using integral water proofing compound as per mfr's instructions finished even and smooth without using extra cement complete all as specified and directed.

M&L for cutting grooves in brick / stone wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar (1:3) complete all as directed.

M&L for preparing plastered surfaces,with approved bituminous primer @100 gms/sqm and applying water proofing treatment on wall,roof,chajja's,gabble walls, edges (at any height )etc and stick with non-woven polyster matt modified APP Membrane as reinforcement weighing not less than 3.5 Kg/sqm and applying one coat of aluminium paint on top of the membrane (at any height ) complete all as specified

Demolition of concrete in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work

M&L for preparation of old painted surfaces of wall by completely removing existing treatment by scrapping , cleaning , washing with water etc , and applying Two coats of oil bond distember including filing the surface with crack filler wherever required all as specified and directed . Note :- (i) The coulour scheme of the painting will be as decided by the accepting officer

M&L for preparation of old painted surfaces of ceiling by completely removing existing treatment by scrapping , cleaning , washing with water etc , and applying Two coats of oil bond distember including filing the surface with crack filler wherever required all as specified and directed . Note :- (i) work tobe execute under occupation conditions.

M&L for 3mm thick wall care putty on wall complete all as specified and directed by Engr-in-charge.

M&L for 3mm thick wall care putty on ceiling complete all as specified and directed

M&L for preparation of old painted wooden surfaces exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for Preparing new painted wooden surfaces exc. 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparing old painted steel surfaces exc.10cm width or girth and applying one coat of synthetic enamel paint , including grills, gate complete all as specified and directed .

M&L for preparation of old painted surfaces of wall , cleaning , washing with water etc , and applying one coat of exterior emulsion paint (Appex paint) , including filing the surface with crack filler wherever required all as specified and directed . Note . (i) The coulour scheme of the painting will be as decided by the accepting officer (ii) Work to be execute in any respective ht of building

M&L for Preparing old painted plastered / concrete surfaces of wall and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for Preparing new plastered surfaces of walls applying two coats of distemper oil bound all as specified and directed.

M&L for Preparing new plastered surfaces of ceiling applying two coats of distemper oil bound all as specified and directed

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets andincluding re-fixing in position complete all as specified and directed.

S&F 6 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screw as work in ceiling flat or sloping.

S&F anodised aluminium snap grid frame work for false ceiling all as specified

Dismantling structural steel work wrought in on or mild steel work including doors, gates but excluding framed truss etc.

S& F Framed work Fe 410-W (Gde E-250) quality A as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doo0rs etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

S& F Mild steel, plain black sheet 1mm thick in wall cladding, steel gates roof, and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

Excavating over areas, n exc 1.5 m deep and getting out in hard dense soil all as directed

M&L for cement concrete in foundations, filling and mass-concrete Type D2 1:4:8 (40 mm graded aggregate)

M & L preparing new sur- faces plastered of wall & applying two coat of cement paint over a coat of primer complete all as directed.

M&L for hard core of gauge exc 63mm but not exc 100 mm , deposited, spread and levelled in layers n.exc 15cms , watered and rolled/rammed to a true surface .

Roughening old Stone Sett flooring surfaces by using machine grinder, surface should be make completely rough and non skid and throughly water clean the surface after grinding

Dismantling of stone sett pavings any description or thickness laid bedded pointed in cement mortar in floors, appron etc complete all as specified and as directed.

M&L for Stone Sett flooring with stone setts of size 200 to 250mm long,150 to 200mm wide and 150mm deep and sides dressed and smooth finished on top; bedded in cement mortar (1:3), joints 20mm thick; grouted in cement mortar (1:2) with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified and directed.

S&F for MS tubes as in railing for horses jumping lane cut into required size and shapes, welded, embedded in foundation PCC and MS plates as top cover as per dia of pipe including necessary welding and finished at all sides ,size of MS tube , approved make ,necessary welding to holes, framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specifed and directed

Excavating in post holes (or similar holes) each n. exc 0.5 cum getting out returning in and ramming earth or broken rubble mixed with earth around in layer not exc 25cms watering and removing surplus soil to a distance n.exc 50 m and making good surfaces in hard / densesoil.

M & L for providing cement concrete type B2 (1:2:4) in foundation ,filling and mass concrete complete as specified.

M&L preparation of new surfaces of steel exc 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of red oxide complete all as directed.

Surface dressing n exc 15cm deep of soft / loose soil, incl removing of shrub,grass vegitation etc complete all as specified and directed

M&L for reinforced cement concrete (nominal mix) Type B1 (1:2:4) using 20 mm graded aggregates in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L for reinforced cement concrete (nominal mix) Type B1 (1:2:4) using 20 mm graded aggregates in Columns, pillars, piers, posts and struts

M&L for formwork to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar works, vertical or to batter.

M&L for Formwork to rough finished surfaces of concrete sides of columns, posts, struts, piers, pillars and stanchions as specified and directed.

M & L for rendering 15mm thick for concrete or pcc wall surface in cm 1:4 to be finished even and smooth without using extra cement all as specified and directed

M & L for errecting of brass 1" pipe for different type of purpose all as directed

Taking down carefully copper/aluminium point wiring (light/fan/socket) including all accessories wire, casing caping/conduit, screws etc and making good the disturbed surfaces all as directed

M&L for point wiring in and including new PVC casing and capping with the help of multi-stranded unsheathed FRLS copper cable 1.5 sqmm 650/1100V conforming IS :3419-1988 adhereing to colour code including earth wire of the size 1.5 Sqmm green colored as indicated and shall conform to IS 14772-2000 for the following :- One light /fan controlled by one switch one way

Ditto all as per item No. 170 above but one 3 pin socket outlet , 5 amps on independent board

Ditto all as per item No. 170 above but one 3 pin socket outlet , 5 amps on same board

Ditto all as per item No. 170 above but one 3 pin socket outlet , 15 amps on independent board with cable FRLS grade 2.5 Sqmm and 2.5 sqmm as earth wire

Ditto all as per item No. 170 above but one bell/ buzzer point controlled by one push button on independent board with cables FRLS grade 1.5 sq.mm size

M&L for switch piano Conform IS 4615-1968 flush type 5 Amps single pole one way.

M&L Switch socket Combination 16A, 6 pin, flush type.

M&L Switch socket combination 2 in 1, 5A flush type

M&L socket outlet Conform IS 4615-1968, 2 in 1 , 3 Pin 5 Amps flush type .

M&L in electronic step type ceiling fan regulator Conform IS 4615-1968 120W, flush type.

M&L in replacement of bell push flush type 5Amps single pole (Make:Anchor/Cona)

S&F electric bell Ding Dong type AC, 230 volts single phase complete all as specified.

S&F ceiling rose surface shall comply with IS :371-1979 Bakelite 60x 25 mm two to three terminals plates and of outside diameter not less than 63.5mm.

S&F LED tube light with diffused optics ultra bright LED tube light 18/20watt with high efficiency,integrated aluminum heat sink suited for installation in existing T8 tube light with G13 lamp holders all as specified. Make : Luker/Philips/Crompton

S&F 1x18/20W,230V surface and wall mounted batten suitable for installing LED Tube including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified Make : Luker/Philips/Crompton

S&F 1x10W,230V, (warm white)LED batten suitable for indoor application of color temperature 3000K surface /wall mounted LED batten including connecting up with twin core twisted flexible copper conductor cable from ceiling rose all as specified . Make:Luker/Havellls/Crompton

S&F polycarbonate angle holder retrofit type suitable for LED bulb of B-22 base including 01 nos 15 watt LED Bulb all as specified and directed by Engr-in-Charge.

S&F decorative wall light fixture made up of Polycarbonate,suitable for LED bulb (B-22 base) including one 18/20 Watt LED bulb and fixing on wall with necessary accessories. Make - Luker cat part No LWL114-1 or equivalent in Philips/Crompton

S&F LED table lamp fittings white colored with necessary accessories including surface PVC box of circular/square type for mounting table lamp all as specified and directed by Engr-in-Charge. Make: Luker Cat Part No LSP04 or equivalent in Havells/Crompton

Taking down the ceiling fan/exhaust fan carefully and cleaning/Servicing the fan if any repairs/replacing of parts required complete including painting the fan with enamel spray paint white colored and fixing back the fan with fixing accessoires required at site.

S&F LED security light fiitting 20 W,IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens embeded PC cover having TOP opening seperate driver compartment complete fixing with GI bracket made out of 40mm bore GI pipe light grade suitable length bend to shape and fixed to pole/wall with necessary MS clamp accessories complete all as specified and directed by Engr-in-charge. Make:lLukar Cat Part:LSTE20(Sleek series) or equivalent in Havells / Crompton

S&F Vertical Stationary type electric water heater closed/vented type, inner body made out of copper of capacity 25 Litres suitable for 230 volts , single phase AC 50 HZ Supply ISI marked to IS;2082 (Part /1993) (reffirmed 2004) with latest amendments and having BEE Star (5 Star Rating) complete and grouting with nut bolts/fastners of suitable size complete all as specified and directed Make: Racold/Havells/V Guard

S&F GI mesh flexi connection pipes 15mm dia suitable for hot & cold water not less than 450 mm long with brass metallic flexi nuts on both ends of pipe.

S&F NRV 15 mm dia, vertical type, cast copper alloy high perssure all as specified and directed

S&F in replacement sheet metal enclosures single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc all as directed.

Taking down carefully sub main wiring of any type and size and making good disturbed surfaces complete as specified.

M&L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 4 Sqmm , 1100 Volts grade in and including surface conduit heavy grade not less than 20mm complete with accessories and copper cable 4 sqmm continuous earth wire complete all as specified and directed (Two runs of 04Sqmm cable with 01 run of 04Sqmm earth wire along with surface conduit shall be measured as one RM)

M&L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 6 Sqmm , 1100 Volts grade in and including surface conduit heavy grade not less than 20mm complete with accessories and copper cable 6 sqmm continuous earth wire complete all as specified and directed (Two runs of 06Sqmm cable with 01run of 06Sqmm earth wire along with surface conduit shall be measured as one RM)

S&F in replacement MCB DB 02 way SPN single door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete alongwith its accessories by removing from existing circuits and refixing the new DBs and existing circuits complete as reqd at site

S&F MCB DB 04 way SPN single door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and existing circuits complete as reqd at site

S&F MCB DB 08 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and existing circuits complete as reqd at site

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing.

S&F C Curve MCB SPN 40 Amps working on 240 volts, 50 HZ,10 KA all as specified and directed.

S&F MCB TPN 40 Amps 415V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing.

S&F electrical meter box compartmentalized design suitable for 4 x energy meter and 1 x Four way SPN DB, 4 X Two way SPN DB outdoor wall mounted type, weather proof fabricated out of not less than 2.0 mm thick CRCA sheet, powder coated in siemens grey colour, double door. The enclosure shall be front openable with locking arrangement and provided with 5 mm thick bakelite sheet for mounting the energy meters and MCB DB. The enclosure shall be provided with suitable size PVC cable glands for incoming and outgoing cables/wires. The overall size of the meter box should be as per site requirement complete with all accessories pre wired twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. (Note: quoted rate shall deemed to including for disconnecting existing circuits from DB's and energy meter and same has been refixed in new meter box)

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia of minimum 15m length by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR PART-I connected to earthing test point all as specified or indicated including provision of earthing lead protection pipe, PCC earth pit with cover, excavation & earth work, testing on completion etc all as specified and directed

M&L for laying XLPE underground cable 16 sqmm 4 core armoured sheathed with PVC cable stranded aluminium conductor 1100 volts grade

M&L for laying of reinforced concrete pipe, dia of 150 mm 2 nos half round for bottom and top and before laying excaved area shall be levelling all as specified and directed by Engr-In- Charge . Note: One half round Top and One half round bottom together will be considered as one running meter. Make as per sample approved by Engr-In-Charge

M&L for cutting of existing road/ hard standing by providing suitable T&P to make suitable size trench for laying 50 mm dia pipe in road crossing etc. including the cost of making good the disturbed surface and matching with existing (Chequered tiles/Road/PCC) complete all as specified and directed

S&F GI tubing light grade 50 mm dia ISI marked with all fittings laid in trenches and fixed pole by flat iron clamps, nut,bolt,washers suitable size all as specified and directed at size.

Bharekar Construction

Sarkar Enterprises

J D Contruction

Sunil Constructions

M/S Narendra Construction