SPL REPAIR TO P-114 AND T-71 (TRAUMA CENTRE) AT BASE HOSPITAL UNDER GE (E/M) BASE HOSP, DELHI CANTT-10

Amount

Taking down wooden roof trusses coupled rafter or trussed beam above 12.00 M complete all as specified and directed.

Dismantling timber scantling in fillet, rail post, rafter, purline etc under 40 Sqm in section in any position unframed work complete all as specified and directed.

Dismantling post, angle and tubular truss, purlin, rafter & struts (wood, steel, RCC) any section including taking out embeded portion and making good disturbed ground post embeded in concrete complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layer not exc 25cm in soft/ loose soil including PCC complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (40mm graded agg) as in foundation, filling and mass concrete complete all as specified and directed.

S&F Steel work in tubular trusses, purlins, rafter, vertical post and similar works including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS- 1161-2014 Gde YST-240 including one shop coat of zinc chromate primer paint including prepartion of surface at contractor workshop before fabrication complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for rolled sections as in main and cross beams, hip and jack rafter, purlin where connected to common rafter and running rails and guides for sliding doors framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings etc confirming to Fe 290 Gde- E 165 complete all as specified and directed.

M&L for plates(plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding complete all as specifed & directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

M & L for applying one coat of synthetic enamel paint to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of old steel surfaces.

Dismantling Asbestos cement corrugated/semi-corrugated sheets in roof coverings including ridges etc complete all as specified and directed.

Supply & fixing Pre-painted galavalume alumininum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 MPa as in roof covering fixed with self tapping screws complete all as specified and as directed .

Supply & fixing Pre-painted galavalume alumininum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering,rain water gutter,ridge fixed with self tapping screws complete all as specified and as directed .

S&F of 3 mm thick fibre glass reinforced translucent corrugated printed sheeting with two corrugations or plain sheet , side lap fixed with coatch screw and washer in roof, wall etc complete all as specified and directed.

Dismantling of wall and ceiling board including frame GI / Aluminium (fibre, pulp, insulation etc) or insulation boards/slab of any thickness and any description including cover fillets complete all as specified and directed.

S&F in repair 12 mm thick medium density fire retardant mineral fibre ceiling board of any size and fixed in ceiling of frame GI powder coated main runner (T) 25 x 32 mm, croos runner (T) and wall angle 25 x 25mm and suspended 3mm dia with adjustement any height including necessary accessories etc complete all as specified and directed.

Refixing only false ceiling of PVC profile 10mm thick of 1mm sheet thickness screwed over grid of panel size not exc 1200mm x 600mm using new mild steel RBS of size 50mmx25mmx1.6mm suspended with 3mm GI wire at a distance not exc 1.20 mtr in both direction on dash fastener embeded in soffit of roof complete all as specifed & directed.

Demolition of Mud in roofs, any thickness, including PCC/plastering and leeping complete and removing the spoil to a distance exc 250 m but n exc 500 m complete all as specifed & directed.

M&L for providing plain cement concrete, type B-0, 1:2:4 (using 12.5 mm graded stone agg) as in roof padding, Gola, etc including cleaning the surface by wire brushing complete all as specified and directed.

M&L for 20 mm thick rendering on concrete surface of roof with cement mortar 1:4 is to be finished even and smooth(without using extra lime or cement) and including mixing of water proofing compound as per manufacturers instruction complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately

Supply only water proofing compound (powder)complete all as specifed & directed.

M&L for roof treatment with polymeric membrance (APP based) with non woven polyster mat as reinforcement with following:- (a) M&L for cleaning the new plastered surface and providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.30 Ltr/Sqm on dry and clean surface. (b) M&L for providing & laying APP based polymeric membrane of 3 mm thickness of weight of 3.0 Kg/Sqm with non woven polyster fibre as reinforcement on primed surface by torch application with 15 cm end over laps & 10 cm side over laps etc as per manufacturers instruction. (c) M&L for finishing of top surface by a coat of aluminium paint complete all as specified and directed. Make: Ms Fosroc Chemicals/Ms STP limited/Ms IWL India limited/Ms Tiki tar Danosa (India) Pvt Ltd/Ms Torchtar Membrane & Bitumen Pvt Ltd.

Demolition of stone slabs laid bedded and pointed in any mortar and cladding tiles of any description or thickness in floors, aprons, walls, etc and removing the debris off MOD land complete all as specified and directed.

M&L 20 - 25 mm thick machine cut kota stone flooring laid over and including screed bed or bedding layer mortar 15mm thick in cement mortar 1:4 for laying floor finished jointed and pointed with grey cement slurry mixed with pigments to match the sheds including all grade rubbing and polishing upto mirror (polishing) image complete all as specified and directed.

All as per item No. 25 above but 10mm thick on skirting/dado including & over 10 mm thick rendering coat in cement mortar 1:3 complete all as specified and directed.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) in floors, steps, cooking platforms and like over and including 15 mm thick in cement screed mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of other than white and black including moulding, etc complete all as specified and directed.

M&L Granite Zed black (As approved by the GE)18 to 20mm thick work (table rubbed and polished) in floors,steps, jambs, pillars, window-cills,cooking platforms including 20mm thick screed bed or bedding in Cement Mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for 10-12mm thick Zed black granite stone(superior Quality) slab of (table rubbed and polished) as in wall lining (venering to wall) and the like, over & including 10 mm thick plastering in Cement Mortar 1:3 including pointed in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F fasteners to the granite tiles in walls including drilling the holes and fixing the same complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding and and including disposal of all debris removed in MOD land complete all as specified and directed.

M&L for Vitrified Ceramic tiles digital coloured double charged 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed.

M&L for 7mm to 8mm thick ceramic non skid tiles coloured of area exc 0.11 Sqm but nexc 0.18 Sqm (400x400mm) in flooring set and jointed in neat cement slurry and pointed in coloured cement to match with tiles laid on 15mm thick cement screed (1:4) complete all as specified and directed.

M&L for digital coloured glazed ceramic tiles of size 600x300mm and 7mm thick in vertical surfaces (including designed borders ) such as skirting and dados set and jointed in neat cement slurry pointed in coloured cement to match over rendering 10 mm thick on fair faces of brick work in Cement Mortar (1:4) complete all as specified and directed. Note:- Rate of Designer border in vertical surface will be deemed into quoted rates

Demolition of brick work built in cement mortar including all quoins, arches, pilllars etc. and precast articles including disposal of demolished material complete all as specified and directed.

M/L for brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in Cement Mortar 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out of joints, hacking for key, scrubbing down with water etc. any description complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:6 on fair faces of brick or concrete, new surfaces of walls finished the surface fair and even without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:4 on other than fair faces of brick surfaces of walls finished the surface fair and even without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying 3 mm thick wall care putty and applying two coats of Oil Bound Distemper over a coat of chalk whiting complete all as specified and directed.

M & L preparation of new surfaces of walls plastered or unplastered and applying two coats of cement base paint over a coat of primer to walls to obtain uniform surfaces including making good the surface complete all as specifed & directed.

M & L for complete removal of existing treatment from old decorated wall surface by scrapping by electrically operated grinder machine and applying priming coat of chalk whiting followed by two coats of Oil bound distemper of any tint on walls complete all as specified and directed.

M & L for complete removal of existing treatment from old decorated wall surface scrapping by electrically operated grinder machine from old decorated wall surface by scrapping and filling all patches with cement wall putty and applying one or more coat of Cement based paint on patches to bring the whole and applying two coat of Cement based paint on walls complete all as specified and directed.

M&L for complete removal of existing treatment from old decorated ceiling surface by scrapping / washing and applying 3 thick cement wall care putty of make Birla/ Asian and making the surface smooth by rubbing the surface applying priming coat of chalk whiting followed by two coats of Oil bound distemper comlete all as specified and directed

Taking down aluminium door chowkat any size with shutter including all fittings complete all as specified and directed

Taking alluminium window/ventilators chokhat any size with shutter including all fittins complete all as specified and directed

Taking down old alluminium partition, any description fixed in any position complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutter from the frames) n exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sqm but n exc 4.00 each complete all as specified and directed.

S & F in repair powder coated aluminium anodised section 40 x 44x14mm gauge for aluminium partition wall in wall in panel 1m x1m covered with 5mm thick plain/frosted tinted glass on top half portion and 12mm thick pre-laminated sheet fixed in half bottom portion complete all as specfied and directed.

Re fixing old existng powder coated aluminium anodised section 40 x 44mm x14 gauge for aluminium partition wall in wall in panel 1m x1m covered with 5mm thick plain/frosted tinted glass on top half portion and 12mm thick pre-laminated sheet fixed in half bottom portion complete all as specfied and directed.

S&F aluminium powder coated door frame with partially glazed shutters single/ double leaf divided into two glazed panels including aluminium anodised snap beading and rubber gasket/lining for fixing of glass as directed. The frame shall be fixed with aluminium anodised bolt by drilling in the existing wall and with thrust bolt of suitable size all as directed. The frame and shutter will be made out of the following section and fitting (a) Aluminium anodised door frame 101.60 mm x 44.75 mmx2mm fixed with aluminium thrust bolt in walls by drilling as directed. (b) Aluminium anodised sides rail of shutter section 83.5mmx 44.5mm x 2mm (c) Aluminium anodised bottom rail of shutter section 150mm x 44.5 mm x2mm. (d) Aluminium anodised top and middle rail of shutter section 100mm x 44.5 mm x 2mm. (e) Aluminium anodised tower bolt 200 mm long - 02 Nos in each leaf of Make Classic/Argent as approved. (f) Aluminium anodised handle 250 mm long of approved Make 02. No’s in each leaf. (h) Glass Pane shall be 5.5 mm thick tinted glass. (j) 12mm thick prelaminated particle board laminated both side exterior grade and Mortise lock including complete all as specified and directed.

Supply, fabricating and fixing frame and windows of aluminium powder coated of extruded aluminium section two track with two sliding shutters with following sections : (a) Frame section shall be 63.50 mmx38.10 mmx2 mm thick. (b) Two track bottom rail for sliding of shutters 61.85mm x 31.75mmx2mm thick. (c) Two track top section shall be 61.85mmx31.75mmx2mm thick(d) for sliding shutter handle & 'H' bottom section should be 40mmx(18mm+9)mmx1.45mm thick(e) sliding shutter to be provided with 5.5mm thick sheet glass tinted, plain, frosted (f) stainless steel wire clothes 0.36mm nominal dia of wire and average width of aperature 1.40mm (g) Aluminium grill Cat No DG-104, 8 to 10mm thick fixed with separate channel to window/ventilator complete all as specified and as directed.

M&L for powder coated aluminium frame ventilator shutters, sliding type with or without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, 4 to 5mm thick glass panes,rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays/lock, Rollers, hinges type B-21 100mm long (2 no.) suitable handle (1 no per shutter) complete all as specified and directed.

S&F solid PVC moulded door frame of size, 50x47mm, made out of 5mm thick of any colour PVC sheet, reinforced with MS square tube fixed with screw/plugs to brick walls complete all as specified and directed.

S&F Factory made solid panel PVC moulded door shutter 28 to 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails,MS frame shall be covered with heat moulded of any colour PVC 'C' chanel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles &rails eith suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing including complete all as specified and directed.

S&F stainless steel Butt hinges medium weight of size 100mm complete all as specified and directed.

S&F 150 mm size aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 200 mm size aluminium anodised tower bolts of extruded section complete all as specified and directed.

Taking down/Dismantling eaves gutter, rainwater pipes and CI soil,PVC (any type) including all fittings heads,shoes,bends,swan necks etc including cleaning or refixing or removal to store.

S&F in repair 100 mm dia Spun pipe in any length with or without ears, with cement joints, fixed to walls with stack clamps or laid in floors incl taking down old one complete all as specified and directed.

S&F in repair 75 mm dia Spun pipe in any length with or without ears, with cement joints, fixed to walls with stack clamps or laid in trenches or in floors including taking down old one complete all as specified and directed.

S&F in repair 100 mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete in type B1 1: 2:4 including joints, etc including taking down complete all as specified and directed

S&F in repair 100 mm dia cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F in repair 100 mm dia cast iron pipes branch pieces,single (equal or unequal) Tee, sockets, etc with oval access door if required and fitted with stack clamps, etc complete all as specified and directed.

Supply and fixing in repair vitreous China squatting pan, "Orissa" pattern size 580 X 440 mm, white, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc including taking down and complete all as specified and directed.

S & F Vitreous China wash down water closet pan (pedstal pattern) white (squatting pan & trap including connection to drain (or out going pipe and to flushing pipe anti syphonic pipe etc and including taking down complete all as specified and directed.

S & F in repairs plastic water closet seat , black/white, closed pattern with flat bottom & cover and mild steel chromium plated or aluminised hinging device.

S & F in repairs 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve, float, chain and pull and brackets etc complete.

S&F in repair 15 mm bore Bib taps fancy type cast copper alloy with crutch or butterfly handle, screwed down,screwed for iron pipe or brass ferrule fixed complete all as specified and directed.

S&F in repair 15 mm bore stop/angle valve valves fancy type chromium plated screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or unions fixed complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Dismantling of water tanks exc 250 ltrs & n. exc 500 and exec 500 ltrs not exec 1000 ltrs capacity and removing to store complete all as specified and directed.

Disconnecting existing water tanks setting aside for repairs,cleaning and refixing of tank capacity exc 250 ltr but not exc 500 ltr complete all as specified and directed.

S & F PVC water storage tanks of 500 ltrs capacity rotational moulded (multi layered cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F 1000 Ltr cap Rotational moulded polyethylene water storage tanks three layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed in SSR Part-I.

Fixing only PVC water storage tanks of 500 ltrs capacity rotational moulded (multi layered cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S & F in repair ball brass valves, high pressure, with polyethene float and flynut complete screwed for iron pipe of 20mm dia complete all as specified and directed.

S & F ball brass valves, high pressure, with polyethene float and flynut complete screwed for iron pipe of 20mm dia complete all as specified and directed.

Taking up or down 15 mm bore steel water tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15mm bore steel water tubes, medium grade, galvanised with all fittings and fixed complete to walls/ceilings or laid in trenches complete all as specified and directed.

Refixing 15 mm bore old steel tubing and conncetions in new or old position to walls complete all as specified and directed.

Taking up or down 20 mm bore steel water tubing and connections including cleaning or refixing or removal to store complete all as specified and directed.

S&F 20 mm bore steel water tubes, medium grade, galvanised with all fittings and fixed complete to walls/ceilings or laid in trenches complete all as specified and directed.

Refixing 20 mm bore old steel tubing and conncetions in new or old position to walls complete all as specified and directed.

S&Fin repair vitreous china wash hand basin white flat back of size 550mmx400 mm including cutting for and pinning in end of brackets,15mm angular stop cock,32 mm waste fittings,PVC connections 15mm size with PTMT nuts of length 450mm as per reqd size ,brass chromium plated for glazed ware sinks,basins etc.including 15 mm bore CP fancy type piller tap with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed.and flush pipe of polytethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type (back corner wall type),including polytethylene of low or high density or PVC 32 mm dia and 15 mm angular stop cock and PVC connections as per reqd size etc.with 60mm long screwed pointing around urinal back in cement complete all as specified and directed.

S&F in repair for toilet paper holder complete all as specified and directed. Make: Jaguar Cat Part No ACN-CHR-1153S or euivalent in GEM/ MARC

S&F in repair for soap dish complete all as specified and directed. Make: Jaguar Model Kohler 5634 or equivalent in GEM/ MARC

S&F in repair for towel rail complete all as specified and directed. Make: Jaguar Cat Part No CAN-CHR-1111NM or equivalent in GEM/ MARC

S&F in repair for health faucet with 1 mtr tube and hook complete all as specified and directed.

S&F in repair 15 mm dia Brass chromium plated shower rose 125 mm size fixed in repairs complete all as specified and directed.

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F stainless steel hanger 300mm length and 50mm width fixed to wall,doors with the help of 75mm screws complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundations of walls and not exc 10 Sqm on plan and n.exc 1.5m in soft soil complete all as specified and directed.

Returning and filling in soil including levelling, watering and well rammingin layers n. exc 25cm in fdn trenches complete all as specified and directed.

Removing excavated soil including disposal of all debris exc 1.5 KMtr not exc 5 Km outside of MOD land complete all as specifed & directed.

Demolition and breaking up drain pipes (Salt glazed stoneware) set in cement mortar 150 mm internal dia of pipe complete all as specified and directed.

S&F Reinforced concrete pipes,class NP2 laid and jointed complete with collars ware drain pipes laid in trenches and jointed internal dia of pipe 150 mm complete all as specified and directed.

M&L cement mortar concrete bed to drain pipes in PCC 1:3:6 type C-2 (using 40 mm graded crushed stone agg) incl packing under and haunching against the sides of pipes after they are laid and tested in bores of pipe 150 mm dia complete all as specified and directed.

Cutting into existing manholes for connecting new mains pipe making good to pipes rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finish and reforming benching as required, internal dia of pipe 150 mm dia complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floors and paving not exc 15cm thickness( below or above ground level) and removing the debris off MOD land complete all as specified and directed.

M&L for 75 mm PCC 1:3:6 type C-2 (40mm graded agg) as in plinth protection/hard standing and finished the surface even and smooth without using extra cement complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

M&L for mild steel deformed or twisted bars up to 10 mm dia and over cut to length be not shape as required including cranking, bending spirally for hooping for columns, hooking and binding with MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F factory made precast reinforced cement concrete manhole cover(RCC 1:2:4, using 20 mm graded stone aggregate) 100 mm thick (Square/rectangulr/circular) with and including 10 mm dia TMT bars and placed over manholes at site complete all as specified and directed.

M&L for Providing precast cement concrete louvres and jallies type B-0, 1:2:4 using 12.5 mm graded stone aggregate and set in cement mortar 1:6, 35mm thick (measured solid), including all mouldings but excluding frame and applying two coats of white wash including demolition of concrete complete all as specified and directed.

S&F of 4 mm thick Aluminium Composite panel cladding of approved quality and colour as approved by GE,fixing in MS frame at any height and including MS frame of size not exc 0.36 sqm (used in rectangular tubes of size 50.8mmx 25.4mm x 2.9mm thick or square tubes 38mm x38mm x 2.9 mm thick are used in frame) and filling the joints with all weather silicon sealant including all mouldings, cuttings, etc complete all as specified and directed. Make: Aludecor/ Alstrong/ Eurobond

M&L for stainless steel work as in grills, grating ,railing etc with ends shoulderd and rivetted or forged into spikes framed guard bars, balusters conforming to gde -304 with all jointing accessories like elbow, socket etc and fixed with PCC 1:2:4 in posts and the like including excavation where required complete all as specified and directed

M&L for RCC design mix of M-25 (20mm graded aggregate) for foundations including rafts, footings, foundations, beams, plinth beams, bases for column etc, basement for slabs, under reamed piles and mass concrete including necessary form work etc complete all as specified and directed. Note: Steel reinforcement bars shall be paid and measured separately under relevant items.

M&L for RCC design mix of M-25 (20mm graded aggregate) for column, pillars, piers, posts and struts including necessary form work etc complete all as specified and directed. Note: Steel reinforcement bars shall be paid and measured separately under relevant items.

M&L for RCC design mix of M-25 (20mm graded aggaregate) for beams (lintel, roof beam and gable beam), cantilever, bressummers, lintel over 1.50m span including necessary form work etc complete all as specified and directed. Note: Steel reinforcement bars shall be paid and measured separately under relevant items.

M&L for RCC design mix of M-25 (20mm graded aggregate) for chajjas etc including necessary formwork complete all as specified and directed. Note: Steel reinforcement bars shall be paid and measured separately under relevant items.

M&L for drilling holes of 20mm dia and 250mm deep in brick masonry and filling the holes in cement mortar 1:3 and grouting TMT bars of 12mm dia in it complete all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete (fitting such as switches, ceiling roses, pendent, regulator socket etc to be measured separately) and making good disturbed surfaces of wall floor etc complete all as specified and directed.

Taking down old and unserviceable sub main wiring and removing from the site and making good the disturbed surface complete all as specified and directed.

Taking down ceiling fan, exhaust fan including connection cable, dismantling blades and removing fan and blades to MES stores complete all as specified and directed.

M&L point wiring for modular switches or normal switches with 1.5 sqmm , single core , multi stranded copper conductor PVC insulated and unsheathed (FRLS) cable 1100 Volts grade, drawn through Surface /concealed Conduit as requirement of site including cadmium plated screws as per ISS, including replacement of 3 mm thick phenolic laminated sheet top covers on and including sunk type CI/steel terminal boxes concealed in wall including 1.5 Sqmm size pvc insulated unsheathed copper earth continuity conductor to common earth and connecting to earth dolly for One light point controlled by one switch 5 Amps one way single pole complete all as specified and directed.

All as per item No. 120 above but one fan point controlled by one switch 5 Amps one way single pole on idependent board complete all as specified and directed.

All as per item No. 120 above but one three pin 5 Amps socket out let on independent board complete all as specified and directed.

All as per item No. 120 above but one three pin 5 Amps socket out let on same board complete all as specified and directed.

All as per item No. 120 above but one bell point controlled by one bell push independent board complete all as specified and directed.

All as per item No. 120 above but point wiring of copper cable multi stranded 2.5 Sqmm size for 15 Amps socket outlet on independent board with 2.5 Sqmm size of earth conductor complete all as specified and directed.

All as per item No. 120 above but point wiring of copper cable multi stranded 2.5 Sqmm size for 15 Amps socket outlet on same board with 2.5 Sqmm size of earth conductor complete all as specified and directed.

All as per item No. 120 above but point wiring of copper cable multi stranded 4.00 Sqmm size for AC point wiring with 4.0 Sqmm size of earth conductor complete all as specified and directed.

M&L for point wiring Casing caping complete using 1.5 Sqmm PVC insulated FRLS unsheathed copper conductor, stranded cable upto and including working voltage 1100volts grade, ISI marked, PVC fittings such as bend,tee,junction boxes elbows etc including pressed steel terminal sunken boxes of size 1.2mm covered with 3mm thick plastic laminated sheet ISI marked top cover fixed with Brass screws and unsheathed copper conductor stranded cable earth continuity wire connected to DBs/sunken boxes/fittings of size 1.5 Sqmm Cross sectional area complete all as specified and directed.

All as per item No. 128 above but one fan point controlled by one switch 5 Amps one way single pole on independent board complete all as specified and directed.

All as per item No. 128 above but one three pin 5 Amps socket out let on independent board complete all as specified and directed.

All as per item No. 128 above but one three pin 5 Amps socket out let on same board complete all as specified and directed.

All as per item No. 128 above but point wiring of copper cable multi stranded 2.5 Sqmm size for 15 Amps socket outlet on independent board with 2.5 Sqmm size of earth conductor complete all as specified and directed.

All as per item No. 128 above but point wiring of copper cable multi stranded 2.5 Sqmm size for 15 Amps socket outlet on same board with 2.5 Sqmm size of earth conductor complete all as specified and directed.

Supply and fix in repair Switch Piano type, white polycarbonate body, single pole, one way 6 amp, 230 V, including connecting complete all as specified and directed.

Supply and fix in repair Switch Piano type, white polycarbonate body, single pole, one way 16 amp, 230 V, including connecting complete all as specified and directed.

Supply and fix in repair socket white polycarbonate body, 6A- 230 V, 2/3 pin combined, including connecting complete all as specified and directed.

Supply and fix in repair socket white polycarbonate body, 16A- 230 V, 3 pin combined, including connecting complete all as specified and directed.

Supply and fix in repair normal type stepped type electronic fan regulator, white polycarbonate body, flush type, 230 V, including connecting complete all as specified and directed.

Supply and fix in repair Lamp holder, white Polycarbonate body, with back plate suitable for batten fittings fixed in position & connecting complete all as specified and directed. Make : Anchor/Cona/Legrand

S & F in replacement Ceiling rose, PVC/ polycarbonate, isolated body type three terminal, 240 volt complete all as specified and directed.

S&F in repair Modular switch piano , flush button type , single pole , one way 10 Amps complete all as specified and directed.

S&F in repair Modular switch piano , flush button type , single pole , one way 15 amps complete all as specified and directed.

S&F in repair Modular socket outlet 3 pin and 2 pin , 10 amps , flush type complete all as specified and directed.

S&F in repair Modular socket outlet 2-in-1, 3 pin, 10 and 20 amps , flush type complete all as specified and directed.

S&F in repair modular type one way electronic fan regulator (5 Step up type) 280 Volts suitable for ceiling fan complete all as specified and directed.

S&F in repair existing sheet metal enclosure with socket plug top, single pole and neutral enclosure with a two pin earth plug and socket complete with one MCB of capacity 25 Amps , 240 Volts complete all as specified and directed.

M & L Sub main wiring using two single core PVC insulated FRLS cable 2.5 sqmm copper conductor multi stranded and 2.5 sqmm copper conductor insulated cable using as earth wire and drawing in to PVC conduit complete all as specified and directed. Note Two runs of 2.5sqmm copper FRLS cable & one run of 2.5 sqmm copper cable in and including 25mm PVC conduit medium grade will be measured as one unit.

M & L Sub main wiring using two single core PVC insulated FRLS cable 4 sqmm copper conductor multi stranded and 4.0 sqmm copper conductor insulated cable using as earth wire and drawing in to PVC conduit complete all as specified and directed. Note: Two runs of 4sqmm copper FRLS cable & one run of 4.0 sqmm copper cable in and including 25mm PVC conduit medium grade will be measured as one unit.

M & L Sub main wiring using two single core PVC insulated FRLS cable 6 sqmm copper conductor multi stranded and 6.0 sqmm copper conductor insulated cable using as earth wire and drawing in to PVC conduit complete all as specified and directed. Note: Two runs of 6 sqmm copper FRLS cable & one run of 6.0 sqmm copper cable in and including 32mm PVC conduit medium grade will be measured as one unit.

M & L submain wiring using four run PVC insulated FRLS Copper conductor 10 sqmm with rigid non metalic PVC conduit of size 32 mm dia medium grade inclusive of boxes (junction/terminal) all tees, bends, elbows, reducers bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook including all fixtures /fittings fixed on wall/ceiling with saddles PVC with earth continuity wire copper conductor PVC insulated unsheathed 10 Sq mm etc complete all as specified and directed. Note: four runs of 10 sqmm copper FRLS cable & one run of 10 sqmm copper cable in and including 40 mm PVC conduit medium grade will be measured as one unit.

M & L submain wiring using four run PVC insulated FRLS Copper conductor 16 sqmm with rigid non metalic PVC conduit of size 40 mm dia medium grade inclusive of boxes (junction/terminal) all tees, bends, elbows, reducers bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook including all fixtures /fittings fixed on wall/ceiling with saddles PVC with earth continuity wire copper conductor PVC insulated unsheathed 16 Sq mm etc complete all as specified and directed. Note: four runs of 16 sqmm copper FRLS cable & one run of 16 sqmm copper cable in and including 50 mm PVC conduit medium grade will be measured as one unit.

S & F in repair distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 4 way with 200 Amps rated copper busbar, neutral bar, earth bar, IP 43 protection, single pole and neutral 250 Volts, flush to wall complete all as specified and directed. Make : Legrand Model: 507610 or equivalent in L&T/ABB/Scheneider/Seimens/C&S Electric/Havells

S & F in repair distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 8 way with 200 Amps rated copper busbar, neutral bar, earth bar, IP 43 protection, single pole and neutral 250 Volts, flush to wall complete all as specified and directed. Make : Legrand Model: 507611 or equivalent in L&T/ABB/Scheneider/Seimens/C&S Electric/Havells

S &F in repair distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 12 way with 200 Amps rated copper busbar, neutral bar, earth bar, IP 43 protection, single pole and neutral 250 Volts, flush to wall complete all as specified and directed. Make : Legrand Model: 507612 or equivalent in L&T/ABB/Scheneider/Seimens/C&S Electric/Havells

S & F in repair with taking down distribution board (DB), double door type made out of sheet metal enclosure (CRCA sheet) dust and vermin proof MCB DB, TPN 12 way with 200 Amps rated copper busbar, 415 Volts with in built MCCB 160 Amps, 10 KA, 01 No., earth bar IP 43 protection, flush to wall complete all as specified and directed. Make : Legrand Model: 507748 or equivalent in L&T/ABB/Scheneider/Seimens/C&S Electric/Havells

S & F in repair MCCB TP 415 V, 160 Amps, 36 KA, 3 Pole complete all as specified and directed.

S & F in repair MCB TPN, 415 Volts, 100 Amps complete all as specified and directed.

S & F in repair MCB TPN, 415 Volts, 40-63 Amps complete all as specified and directed.

S & F in repair MCB SPN, 240 Volts, 32-63 Amps complete all as specified and directed.

S & F in repair MCB SP, 240 Volts, 6-40 Amps complete all as specified and directed.

S & F in replacement for existing 36/40 Watt tube light fiiting by energy efficient LED light fitting 18/20 Watt,230 Volt of 1200 mm + 50 mm length along with fixture, heat sink, environmental friendly, energy efficient, wall mounted batten integrated electronic driver complete all as specified and directed. Make : Havells Cat Part LUMILINEBS20WLED865PCWH or equivalent in Philips/Bajaj/Crompton Greaves/C&S Electric/Halonix

S & F in replacement for existing 18/20 Watt tube light fiiting by energy efficient LED light fitting 9/10 Watt,230 Volt of 600 mm + 60 mm length 6000 K colour temp ,decorative ultra slim linear LED lighting fixture with extruded Al. heat sink, environmental friendly, energy efficient, wall mounted batten integrated electronic driver complete all as specified and directed. Make : Havells Cat part LUMILINESBS9WLED865SPCWH or equivalent in Philips/Bajaj/Crompton Greaves/C&S Electric/Halonix

Supply and fix in replacement Energy efficiency recessed mounted 40 W LED luminire suitable for 2 x 2 grid ceiling along with flat diffuser along with constant current electronic driver complete all as specified and directed by Engg-in-Charge Make : Havells Cat part VENUSNEOHE2X2PLR18-42WLED857MOD+LEDDRIVER36V36WS or equivalent in Philips/Bajaj/Crompton Greaves/C&S Electric/Halonix

S&F in replacement LED Street Light fitting 45 watt, system efficiency not less than 100 lumen / watt, IP65 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws, fixed on existing bracket & connecting including taking down old light fitting of any description complete all as specified and directed. Make : Havells Cat part ENDURAPEARLNEOSL45WLED757SASYTOPC or equivalent in Philips/Bajaj/Crompton Greaves/C&S Electric/Halonix

S &F in repair Earthing complete with galvanised GI earth plate eletrode 600x600x6mm thick,burried directly in ground (earth pit not less than 2.25mtrdeep below GL) with top edge of the plate not less than 1.5mtr below normal GL surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all round the plate using 4mm dia GI wire as earth wire electrode welded and revetted to earth plate at one end connected to main DBs of Bldg at another end GI earth wire encased in and including 15mm dia GI light grade pipe through upper end of earth plate upto main DB of bldg with 20mm bore GI pipe light grade as water pipe from earth chamber to upper edge of earth plate MS funnel with wire mesh fixed on water pipe and Provn of PCC pit in PCC 1:2:4 type B-1 chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type BI duly reinforeced with MS bars 8mm dia @ 150C/c with both ways complete with lifting handle all as shown in electrical plate no 5 of SSR of part-I (1991) complete all as specified and directed by Engr-in-charge.

M & L for painting of ceiling fans/ exhaust fan complete, in situ with syntetic enamel paint as per existing color by spraying including filling cavities with filler, one coat after cleaning all dust, and refixing the same its position after complete servicing all as specified and directed by Engg -in-charge.

S and F ceiling fan 1200mm, BEE 5 star rating including 2 to 3 feet size of down rod and flexible wire 2 core of size 23 X .0076' and clamps and nut and bolts complete all specidied and directed. Note :- Old unserveciable ceiling fan will be deposited to MES store yard.

S& F exhaust fan 300 mm dia sweep, 900 RPM, 240 Volt heavy duty exhaust fan with louver shutter and brackets, connection with flexible PVC copper cable 3 core of size 1.5 Sqmm of length from ceiling rose to exhaust fan including nut bolt and washers of suitable size complete all as specified and directed. Note :- Old unserveciable exhaust fan will be deposited to MES store yard.

S & F Water heater geyser of capacity 35 Ltr AC Single Phase 240 Volts, 2 KW with all assessories such as copper tank, assembly, element including plumbing works, elect connection ,geyser mounting , incl hot and cold water duty free pvc pipes of size 15mm bore and 60cm long for connection and inlet and outlet pipe line connection , inside the existing wall and making good disturbed surfaces complete all as specified and directed by engineer in charge. Note :- Old unserveciable geyser will be deposited to MES store yard.

S&F in repair of modular white cover plate with frame , 3 module complete all as specified and directed. Make: Anchor Roma/Crab tree/Legrand

S&F in repair of modular white cover plate with frame , 4 module complete all as specified and directed. Make: Anchor Roma/Crab tree/Legrand

S&F in repair of modular white cover plate with frame , 6 module complete all as specified and directed. Make: Anchor Roma/Crab tree/Legrand

S&F in repair of modular white cover plate with frame square type , 8 module complete all as specified and directed. Make: Anchor Roma/Crab tree/Legrand

S&F in repair of modular white cover plate with frame square type , 12 module complete all as specified and directed. Make: Anchor Roma/Crab tree/Legrand

Taking down / Dismantling carefully the indoor and outdoor unit of Split AC / Cassatte AC of capacity 1.5 TR / 2.0 TR with outdoor stand, plate for indoor unit and connected wiring, Transportation of complete set from location to MES store yard, refixing of same AC at location complete all as directed by Engr-in-Charge & detail as under:- (a) Fixing of indoor unit wall mounting type (to be installed inside the room) complete with, draining out arrangement for condensed water, fixing of inter connection pipe, all as directed. Fixing of cooling unit on wall shall be as per standard recommendation practice of manufacturers. (b) Erection of condenser, compressor unit on outside of the building, fixed over old clamp / bracket, all as per standard practice of manufacturer. (c) All civil work such as making hole in the wall for passing of pipe etc, to be done, as directed by Engr-in-Charge including making good disturbed surface. (d) Providing new suction & discharge copper tubing as recommended by manufacturer with cinnected clamp and insulation and 4 sqmm 3 core PVC insulated copper cable from indoor and outdoor unit and from main switch of indoor unit with necessory PVC piping all as specified by engineer in charge.

Taking down / Dismantling carefully the air curtain unit and connected wiring, Transportation of complete set from location to MES store yard, refixing of same unit at location complete all as specified and directed by Engr-in-Charge & detail as under:- (a) Fixing of unit wall mounting type (to be installed inside the room) complete with, wiring and accessories all as directed. Fixing of unit on wall shall be as per standard recommendation practice of manufacturers. (b) Erection of unit on outside of the building, fixed over old clamp / bracket, all as per standard practice of manufacturer. (c) All civil work such as making hole in the wall for passing of wire etc, to be done, as directed by Engr-in-Charge including making good disturbed surface. (d) Providing 4 sqmm 3 core PVC insulated copper cable for unit from main switch of unit with necessory PVC piping all as specified by engineer in charge.

Taking down carefully patient call bell, speaker and cameras and camera wiring, wall mounted fans and making good disturbed surfaces of wall floor etc and deposite to mes store yard and refixing the above said items at location during the execution of work complete all as specified and directed.

M & L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S and F in repair Rigid non-metallic PVC conduit of 25mm dia exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed.

S and F in repair Rigid non-metallic PVC conduit of 32mm dia exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed.

Supply and fix in repair for Modular Bell push 6A 1 Module complete all as specified and directed. Make :- Legrand Cat Part No :-573413 or equivalent in Anchor woods/Philips

Shivom Projects Private limited

M/s GANJOO AND CO

n s kumar and sons

AMIT ASSOCIATES

M/S Yamin