Construction of New Semen Lab in Exotic Cattle Breeding Farm at Eachenkottai in Thanjavur District

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with Filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and filling in foundation and basement with Filling Gravel in layers of not more than 15cm.thick well watered and rammed and consolidation etc., complete complying with standard specification and directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Cement Concrete 1:5:10 (One cement, Five crushed stone sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of M.sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

For Ground Floor

For First Floor

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 10-12mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

For Ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.110mm dia pipe

One Floor

Brick work in Cement Mortar 1:5 (one cement and five crushed stone sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4"including curing, etc., complete complying with standard specifiction.

Foundation and Basement

Brick work in Cement Mortar 1:6 (one cement and six crushed stone sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

For Ground Floor

For First Floor

Brick partition walls of 10.80cm thickness using best quality country bricks of size 8-3/4" x 4-1/4" x 2-1/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

For Ground Floor

Brick work in Cement Mortar 1:3 (one cement and three crushed stone sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Foundation and Basement

Plastering with Cement Mortar 1:5 (One cement and Five plastering sand), 12mm thick used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering .Sand) 10mm thick used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering .sand), 12mm thick used finishing in all floors including curing etc., complete complying with standard s conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Supplying and fixing of Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

UPVC VentilatorSpecification:Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing M.S grills of approved design for open to courtyard grill,grill work to doors, window and ventilators openings and grill gate etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primeretc., complete complying with standared specification.

Dadooing with printed design colour glazed tiles of size 300 x 450 x 6mm set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Supply and fixing of PVC wall Corner beading etc., complete

FLOORING - SEAMLESS VINYL FLOORING WITH ANTISTATIC AND ANTIMICROBIAL PORPERTY. It shall be self-leveling 3.00mm anti-static seamless PVC flooring.Floor shall be smooth, non-slip, impervious material conductive enough to dissipate static electricity but not conductive enough to endanger personnel from electric shock It shall be Electro Static Discharge (ESD) combat PVC seamless flooring of very high quality thickness not less than 2.00mm. Continuous roll shall be used and with minimum joints. The joints to be welded by special PV thermal units using PVC welding bars of same colors.The sheet shall be highly durable to shock and indentation. It shall be scratch proof, inert to body fluids, chemicals and disinfectants & shall not be affected by the temperature variations.The flooring shall be done by skilled workers of the accredited agencies, authorized by the supplier of PVC sheets. The Electrical resistance (Point to ground) shall be within 2.5 X 104 to 5 X 106 Ohms. The floor shall not allow buildup of Electrical charges beyond 100V due to antistatic effect. The corners shall not be terminated sharply & concealed coving shall be used to overlap the wall panel to a height of approx. 25mm & sealed perfectly & uniformly. Self leveling compounds shall be used.

Flooring with Self Designed colour Ceramic Flooring tiles 305 x 305 x 6mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone .Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five crushed stonesand] using best quality of Country Bricks of size 8" x 41/4" x 21/4" with Plastering with Cement Mortar 1:3 [One Cement and Three plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone Sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification. CLEAR SIZE 0.60 X 0.60

Supply & Fixing of Continuous sandwich PUF Wall panels 100 mm thick (Powder Coated) either as single piece, prefabricated, modular, factory made units which consist of an insulating layer of rigid polyurethane foam between two layers of metal sheets, comprises of PUF bonded between two sheets of Pre-coated GI sheets of 0.8 mm thick to produce straight-to-finish panels with all necessary fixtures to complete the work in all respect. The rate is inclusive of design ,shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and as directed by the departmental officers.

Supply & Fixing of Continuous sandwich PUF wall panels 50 mm thick (Pre Coated) either as single piece, prefabricated, modular, factory made units which consist of an insulating layer of rigid polyurethane foam between two layers of metal sheets, comprises of PUF bonded between two sheets of Pre-coated GI sheets of 0.8 mm thick to produce straight-to-finish panels with all necessary fixtures to complete the work in all respect. The rate is inclusive of design ,shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and as directed by the departmental officers.

Supply & Fixing of Continuous sandwich PUF wall panels 50 mm thick (Powder Coated) either as single piece, prefabricated, modular, factory made units which consist of an insulating layer of rigid polyurethane foam between two layers of metal sheets, comprises of PUF bonded between two sheets of Pre-coated GI sheets of 0.8 mm thick to produce straight-to-finish panels with all necessary fixtures to complete the work in all respect. The rate is inclusive of design ,shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and as directed by the departmental officers.

Supply & Fixing of 46 mm thick both side flush doors made of 0.8 mm thick PU painted GPSP sheet with honeycomb kraft paper as infill, 50mm thick door frame made of 1.2 mm thick GPSP powder coated sheets totally flush with the wall panels, hardware like push plates, handles,Double glazed view panel with flush design of sixe 450x750mm, DORMA TS-71 standard arm door closure, SS ball bearing butt hinges concealed automatic drop seal, 1.2mm thick SS 304 kick plate of height 300mm on push side.with all neccesary accessories and fittings as per the required and as per the approval for the Department Officer.

Double Door

Single leaf Door

Supply & Fixing of Hatch door of varying sizes with all neccesary accessories and fittings as per the required and as per the approval for the Department Officer.

Hatch Door (1.20x1.20)

Supplying and fixing of View panels double glazed 50mm thick/100mm thcik with all necessary accessories.

Supplying and fixing of Extruded aluminium powder coated clip on type R 70 covings for the entire wall to wall and wall to ceiling.3D internal/ external corner coves with all necessary accessories.

Supplying and fixing of Return Air risers made of 1.0mm thick GI powder coated sheets with projection above the ceiling for the duct connection, capsule type perforated grill pre-filter and GI collor dampers with all necessary accessories.

Supplying and fixing of Electro magnetic door interlocking system for airlock doors with normally close system logic. with all necessary accessories.

Supplying and fixing of Dynamic Pass Box with Overall Size : 750(W) x 680(D) x1200 (H) and Working Sizes : 600(W) x 600 (D) x 600 (H) with all necessary accessories.

Supplying and fixing of Dynamic Pass Box 3 door with Overall Size : 750(W) x 680(D) x1200 (H) and Working Sizes: 600 (W) x 600 (D) x 600 (H) with all necessary accessories.

Supplying and fixing of Clean room Double Glazed GI Window of fixed type from the profile the size of outer frame 60mm x 58mm with GI/1mm 125GSM and 100% corrosion free, Radiations free pin headed plain or brown colour glass 4mm thick should be provided along with necessary acceories The window should be got approved from the Executive Engineer before use on work

Supply & Fixing of Continuous sandwich PUF panels 50 mm thick for clean room false ceilling arrangements either as single piece, prefabricated, modular, factory made units which consist of an insulating layer of rigid polyurethane foam between two layers of metal sheets, comprises of PUF bonded between two sheets of Pre-coated GI sheets of 0.5 mm thick to produce straight-to-finish panels with all necessary fixtures to complete the work in all respect. The rate is inclusive of design ,shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and as directed by the departmental officers.

Providing accessories for Continuous sandwich PUF panels 50 mm thick for clean room false ceilling arrangements such has outer flashing, inner flasing and aluminium Tee suspension and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and as directed by the departmental officers.

Supply, Fabrication, Erection, alignment and levels as per approved shop drawing of structural steel work in built up sections comprising of ISMB, ISMC, angle, plates and round bar section etc., Necessary permanent rivets, bolts, washers and nuts, handling, straightening, cutting, drilling holes, welding, sand blasting, shop assembly, transport to erection site, storing, leading to erection site and apply a coat of anti-corrosive yellow primer paint of approved make and two coat of MRF enamel paint prior to erection t complete job in all respect. a) Connection Bolt are E350 GR.8.8 (IS3757) b) Hot Rolled are E250 GR, or Equivalent , Plate Grade E350 and all structural steel confirm to IS2062.c) Specification for Cold formed Light gauge Structural Steel Sections Confirm to IS: 811d) Painting confirm to IS 1477 part 1& 2.The rate is inclusive of design ,shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and painting two coats over one coat of primer and as directed by the departmental officers.

Supply, Fabrication, Erection, alignment and levels as per approved shop drawing of structural steel work in single section for purlins, tie runners with sag rods, etc., Necessary permanent rivets, bolts, washers and nuts, handling, straightening, cutting, drilling holes, welding, shop assembly, transport to erection site, storing, leading to erection site and apply a coat of anti-corrosive yellow primer paint and MRF enamel paint prior to erection. The rate is inclusive of design ,shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and painting two coats over one coat of primer and as directed by the departmental officers.

Purlin but with Painted cold rolled steel sections Z Section MET- Z Purlin 150 X 60 x 2.0

Sag rod

Supply and fixing of Ridge made out of 0.50mm thick colour coated galvanized steel sheet (JSW sheet brand or equivalent brand). The both sides will be of 275mm, center angle will be of 120mm and both end drop will be of 30mm. This sheet will be fixed with self-drilling screws. The rate is inclusive of design, shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and as directed by the departmental officers. All the materials used on work should be got approved by the executive engineer before use on works.

Supplying and fixing Colour Galvanum Sheet roof of 50mm thick along with 8mm aluminium bubble insulation sheet with weld mesh including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Supplying and fixing Colour Galvanum Sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying, laying and jointing UPVC Pipe (Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance. (Schedule-40) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. External (Above Ground Level)

40mm dia UPVC Pipe commercial

Supplying, laying and jointing CPVC (Chlorinated Poly Vinyl Chloride) Pipe (Higher pressure rating with higher pipe thickness) Standard Dimension Ratio-11 of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. External (Above Ground Level)

32mm dia CPVC Pipe

25mm dia CPVC Pipe

20mm dia CPVC Pipe

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements

40mm dia Elbow

40mm dia Tee

40mm dia Union

40mm dia Bend

40mm dia Coupler

40mmx32mm Reducer

40mmx32mm Reducer Elbow

40mmx32mm Reducer Tee

40mm Hex Nipple

20mmx15mm dia Reducer

25mmx20mm dia Reducer Elbow

32mmx25mm dia Reducer Elbow

25mmx20mm dia Reducer Tee

32mmx25mm dia Reducer Tee

Supplying CPVC Specials in water supply arrangements (both in internal and external water supply arrangements

20mm dia Elbow

25mm dia Elbow

32mm dia Elbow

20mm dia Tee

25mm dia Tee

32mm dia Tee

20mm dia Bend

25mm dia Bend

20mm dia Coupling

25mm dia Coupling

32mm dia Coupling

20mm dia Union

25mm dia Union

32mm dia Union

20mm dia Hex Nipple

25mm dia Hex Nipple

32mm dia Hex Nipple

Supplying and fixing in position 15mm dia brass SS Elbow Action Tap / SS Heavy Duty Long Body Tap / SS Swan Neck Tap of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

15mm dia brass Big Cock Long Body

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

40mm dia Gate Valve

32mm dia Gate Valve

25mm dia Gate Valve

Supplying and fixing in position White / Colour Special Delux Model Glazed Cascade Type Parryware / Hindware / Equivalent Wall Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover Wall Fitting

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing of White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mm

Supplying and fixing of SS Sink of size 1200 x 550 x 180mm complete as directed by the departmenttal officers.

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories.(a) MS Skid - 1 No.(b) Media 11054 No. Vessel with 20 nb MultiportValve (with Media Pubble and Fine Sand andActivated Carbon Filling) set(c) Feed Pump 0.50 HP – 1 No.(d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents /Osmonic (USA) - 1 No. and Membrane PressureVessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos.(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No.Low Pressure Switch - 1 No.,Level Switch - 1 No. &Necessary CPVC Pipes and Fittings.The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact 500 Liter capacity

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid

160 mm dia PVC Pipe

75 mm dia PVC Pipe

110 mm dia PVC Pipe

Supplying and fixing in position PVC specials of ISI mark of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia PVC Plain bend

110mm dia PVC "Y" with Single door

110mm dia PVC Cowl

110mm dia PVC Tee

75mm dia PVC Plain bend

75mm dia PVC "Y" with Single door

75mm dia PVC Cowl

75mm dia PVC Tee

Supplying and fixing in position CP Two Way Bib Cock with Health Faucet etc., complete complying with standard specification.

Supplying and fixing position CI Nahani Trap of size 100 x 75mm with stainless steel gratings with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing approved best quality CP towel rail 600mm long and 20mm dia pipe.The ends of the pipe is to be bended with required depth and the same is fixled in the wall firmly and the ends are covered with stainless steel cup etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

supplying and fixing if Fine Polished Granite Slab 1200 x 600 of 18 / 20mm thick thick in all floors for urinal partition including for labour charges for fixing and polishing etc.,

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing best approved best quality Procelain CP soap tray of size 150 x 150 x 50 mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position of Steel Ladder using MS Angle of 50 x 50 mm thick for frames and steps. Icluding cutting, granding, welding, and making charges etc., Complete complying with standard specification. And as directed by the depatemetnal officers.

Supply and fixing of Manhole Cover SFRC as per following size including labour and transportation charges etc., complete as directed by the departmenttal officers.

Supply and installation of 24HP VRF outdoor units equipped with highly efficient invertor scroll compressors, special acrylic precoated heat exchanger, low noise condensor fan, auto check function for connection error, auto address setting, with multiple outdoor units, including providing gas charging, pressure testing, leak testing, complete including cartage etc. as required. Refrigerant shall be R410A and all compressors shall be of inverter type only for better efficiency. The part load under normal operating conditions. [

Supply and installation of 20HP VRF outdoor units equipped with highly efficient invertor scroll compressors, special acrylic precoated heat exchanger, low noise condensor fan, auto check function for connection error, auto address setting, with multiple outdoor units, including providing gas charging, pressure testing, leak testing, complete including cartage etc. as required. Refrigerant shall be R410A and all compressors shall be of inverter type only for better efficiency. The part load under normal operating conditions.

Supply and installation of 16HP VRF outdoor units equipped with highly efficient invertor scroll compressors, special acrylic precoated heat exchanger, low noise condensor fan, auto check function for connection error, auto address setting, with multiple outdoor units, including providing gas charging, pressure testing, leak testing, complete including cartage etc. as required. Refrigerant shall be R410A and all compressors shall be of inverter type only for better efficiency. The part load under normal operating conditions.

Design, supply, installation, commissioning and testing of 25±2 mm thick PUF insulated double skinned Floor Mounted AHU of sectionalised sheet steel construction Air handling unit of minimum capacity as indicated and suitable for pumping air against a minimum static head as indicated and complete with fan section with DIDW backward curved centrifugal fan, coil section with cooling coil, suitable for pumping air against a minimum static head of 50 mm wg, 11600 cfm, 29TR, Maximum face velocity across the coil : 500 fpm, Minimum number of rows 6 row,volume control damper provided in supply air outlet. [MR]

Design, supply, installation, commissioning and testing of 25±2 mm thick PUF insulated double skinned Floor Mounted AHU of sectionalised sheet steel construction Air handling unit of minimum capacity as indicated and suitable for pumping air against a minimum static head as indicated and complete with fan section with DIDW backward curved centrifugal fan, coil section with cooling coil, suitable for pumping air against a minimum static head of 50 mm wg, 6800 cfm, 17TR, Maximum face velocity across the coil : 500 fpm, Minimum number of rows 6 row,volume control damper provided in supply air outlet. [MR]

Design, supply, installation, commissioning and testing of 25±2 mm thick PUF insulated double skinned Floor Mounted AHU of sectionalised sheet steel construction Air handling unit of minimum capacity as indicated and suitable for pumping air against a minimum static head as indicated and complete with fan section with DIDW backward curved centrifugal fan, coil section with cooling coil, suitable for pumping air against a minimum static head of 50 mm wg, 4600 cfm, 11.5TR, Maximum face velocity across the coil : 500 fpm, Minimum number of rows 6 row,volume control damper provided in supply air outlet. [M-2683]

Design, supply, installation, commissioning and testing of 25±2 mm thick PUF insulated double skinned Floor Mounted AHU of sectionalised sheet steel construction Air handling unit of minimum capacity as indicated and suitable for pumping air against a minimum static head as indicated and complete with fan section with DIDW backward curved centrifugal fan, coil section with cooling coil, suitable for pumping air against a minimum static head of 50 mm wg, 4200 cfm, 10.5TR, Maximum face velocity across the coil : 500 fpm, Minimum number of rows 6 row,volume control damper provided in supply air outlet. [MR]

Supply, fabrication and erection of Aluminium made duct with supports, etc., for Supply and Return Air Duct, etc.,

Supply and installation of Thermal Insulation for Supply air duct, etc.,

Supply and Installation of Accoustic Insulation for Plenum

Supply and fixing of Extruded Aluminium Supply air Diffusers / Grills with Volume Control Damper

Supply and fixing of Flexible hose [MR]

Supply and Fixing of Hard drawn copper refrigerent piping sizing of 28.60mm with all fittings for suction line

Supply and Fixing of Hard drawn copper refrigerent piping sizing of 22.20mm with all fittings for liquid line

Supply and Charging of R410A refrigerent gas.

Supply and Fixing of PVC Draing piping with fittings, etc

Supply and Fixing of Flexible Canvas connection between Indoor unit and ducting for Supply air duct with unit supply air mouth

Supply and fixing of suitable MS angle frames / Brick , if required necessary Base frame for mounting the VRF outdoor units. [MR]

Supply and fixing of Duct mouth dampers between Indoor unit to ducting, etc.,

Supply and fixing of Fuisible link fire damper for Return Air Duct in AHU Room.

Supply and fixing of 1000 CFM propeller exhaust fan, etc., [MR]

Supply and fixing of High Efficiency particulate Air (HEPA) filter of size 8ft x8ft with 99.97% optical efficiency at .3 micron with following specification: Filter Size : 2 feet x 2 feet x 1 feet Classification : H-13 Construction :Panel Type Efficiency :99.97% Optical efficiency at .3 micron Media : Micro glass fiber paper Spacers: Aluminium Initial pressure drop:25 mm W.C Final pressure drop : 75 mm W.C Duct holding capacity:4750gm/Sq.mtr Framing :Aluminium (Box type) No of pleats : 72 Filtration Area: 26.8 Sq.mtr Face Area : .372 Sq.mtr Washable : No Pleating Process : Machine Pleated Class : 100 accuracy as per NABH Norm

Supply, Installation, testing and commissioning of 2 Mtr EHV Air Curtain with CRCA Powder Coated body, SS 304 Blower Blade with 16Mtr/sec Air Through Velocity. Operating on Single Phase 230V 50Hz AC Supply.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box on wall with 6A one way module switch with module front plate with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box on wall with 6A one way module switch with module front plate with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC Rigid pipe on wall and ceiling with PVC accessories with suitable Module Plastic surface mounting switch box on wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5sq.mm copper wire for Open PVC conduit Plug point ( 8 points / Coil) Higher End

Supply and fixing of single box type 4'20W LED fitting with LED (Higher End) complete with T.W. round block on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 2'X2' 36W LED clean room square type recessed fitting with LED (Higher End) on false ceiling with suitable hanging support with PVC unsheathed copper leads from terminals to fitting

Supply and fixing of 1'X1' 18W LED clean room square type recessed fitting with LED (Higher End) on false ceiling with suitable hanging support with PVC unsheathed copper leads from terminals to fitting

Supply and fixing of WT Bulk Head fitting with suitable with 7W / 9W LED bulb.

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm (12") sweep (Heavy Duty) AC exhaust fan complete with necessary wall opening and making good of the wall.

Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep (light duty) AC exhaust fan.

Supply and fixing of 48W LED Street Light Fitting with LED (Higher End) with 32mm dia. GI Pipe (Class 'B') with 1 No 32mm GI Bend complete on the existing Post / On Wall with PVC Unsheathed Copper Leads With MS Clamps and Painting.

Supply and fixing of 2x3W LED Outdoor Wall Light Fitting IP54 on Wall with PVC unsheathed Copper leads from terminals to the fitting with MS Clamps.

Supply and fixing of 18W LED Outdoor Gate Light Fitting IP54 on Wall with PVC unsheathed Copper leads from terminals to the fitting with MS Clamps.

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

Supply and fixing of 1 no. 6/16A two module socket, 1 no. 16A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End.

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End.

Supply and fixing of 32A DP Surface Mounting Industrial Socket with 32A DP MCB in Sheet Steel Enclosure on wall and making good with Earth Connection. (Higher End)

Supply and fixing of 32A FP Surface Mounting Industrial Socket with 32A FP MCB in Sheet Steel Enclosure on wall and making good with Earth Connection. (Higher End)

Supply and fixing of 32A DP MCB in DP Sheet Steel Enclosure on wall and making good with Earth Connection. (Higher End)

Supply and fixing of 32A FP MCB in FP Sheet Steel Enclosure on wall and making good with Earth Connection. (Higher End)

Supply and fixing of 63A FP MCB in FP Sheet Steel Enclosure on wall and making good with Earth Connection. (Higher End)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only. i) 63A 4P MCB - 1 no ii) 63A 4P 30MA RCCB/ELCB - 1 no. iii) 63A DP MCB Isolator -3 nos. iv) 6A to 32A SP MCB - 18 nos.

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 6 nos. 32A 3P MCB , 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 315 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire with painting of suitable colour.

Supply and run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 6 sq.mm copper wire with painting of suitable colour

Supply and run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth Wire connection of 6 sq.mm copper wire with painting of suitable colour.

Supply and run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth Wire connection of 10 sq.mm copper wire with painting of suitable colour.

Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 4 X 10 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 4 X 10 sq.mm PVC Armoured LTUG Cable with earth connection.

Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3-1/2 x 120 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3½ X 120 sq.mm PVC Armoured LTUG Cable with earth connection.

Supply and providing cable end termination of 3½ X 120 sq.mm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and Laying of 3 1/2 x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3-1/2 x 240 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3-1/2 x 240 sq.mm PVC Armoured LTUG Cable with earth connection.

Supply and providing cable end termination of 3½ X 240 sq.mm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Earthing as per ISI Specification with an Earth electrode of 2.10 Mtr. Class 'B' GI pipe of dia not less than 40mm with Copper Earth Plate of size 125mmX50mmX6mm with Necessary Funneling Arrangements with Necessary Masonry Work and with 38mm RCC Cover Slab for the Brick Masonry.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.

Supply, Commissioning, testing and handing over of 7.5KVA Three Phase input to Single Phase Output True online Micro processor Controlled Double conversion type, True On line UPS system with Isolation transformer with 12V SMF batteries of required numbers with suitable battery Interlink cables for 2 Hours Back up Time, DC power should be minimum 15000W-Hour and with suitable MS powder coated Rack for Batteries complete with the following specifications. CONFIGURATION True On line double conversion ups system with pulse width modulation (PWM) Technology using IGBT inverter. RECTIFIER Full wave(shall fully meet the specified input power requirements ) INPUT: 3 phase 320V – 460V OUT PUT:230V +1% on battery mode FREQUENCY: 47HZ-53HZ SYSTEM DC VOLTAGE: 288V INVERSION TECHNOLOGY: Micro processor controlled, pulse width modulation with Instantaneous sine Wave control using IGBT.INVERTER OUT PUT : ( Out put Galvanic Isolation through Double winding Isolation Transformer at Output of Inverter shall be part of UPS Design ) LOAD POWER FACTOR: 0.8 to lag to unity REGULATION : for Balanced load + 1% For 100% unbalanced load + 2% FREQUENCY: 50Hz + 0.5% WAVE FORM : True sine wave TOTAL HARMONIC DISTORTION : Less than 5% OVERLOAD CAPACITY: Inverse Time Characteristic 125% for 10 minutes 150% for 1 minutesEFFICIENCY : 1. Converter – 90% 2.Inverter - 85% 3. Overall – 80 % ( full load) OPERATING TEMPERATURE : 0 to 45 Degrees centigrade on full load CREAST FACTOR: 3 : 1 RELATIVE Humidity : : 95% at 35 Degree Centigrade non- Condensing CHARGER: Built in solid state automatic float- cum boost charger with constant current, constant voltage mode of charging along with current limiting features. Ripple in DC shall not exceed 2% when battery is disconnected.

PROTECTION( in built) i) output under Voltage ii) output over Voltage iii) ) output over load iv) output short circuit. v) HRC fuses /output/ battery vi) Battery low trip vii) battery charges current limit. INDICATIONS: i. Mains ON ii. Inverter ON iii. UPS ON battery iv. Load On UPS v. Battery LOW METERING: i. Input AC Voltage ii.Output AC Voltage / Load details and Frequency By Pass: Manual

Specially designed to meet stringent MoEF/ CPCB norms of 75 dBA @ 1mtr at 75% load under free field conditions. ƒ The acoustic enclosure is made of CRCA sheets in Munsel green shade and a structural/ sheet metal base frame painted in black. ƒƒ High quality noise absorbant and fre-retardant grade acoustic insulation material (Rockwool) complying to IS 8183. (1) Supply of manuals for operation & maintenance of DG set with warranty card etc. (SR) (H) Fuel Tank 300Ltrs. Removable Fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet an outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for cleaning or any maintenance. I) Battery : 1 No 12 Volts 120AH BatteryJ) Erection, Testing and Commissioning:The Erection shall comprise of the following for generator set.1) Transporting the generating set to the site, unloading the set and move to the existing foundation.2) Erection of generator set with proper alignment over the existing foundation.3 ) Mounting of starting batteries on 1/2" thick hylem sheet base with suitable angle iron frame work supports on the floor by the side of the Generator set to confirm to lates CEIG conditions.4) Providing earth connection by 1" x 1/8" copper and inter connection of earth pit 1" x 1/8" copper flat thirty meters.5) Supply and laying annunciation cable of suitable capacity between engine and the control panel of the generator set 15 mts.6) First charging of lubricating oil first charging of battery and providing requied fuel to the full tank level while handing over to the user dept. to run the set for eight hour on full load testing and commissioning.7) Supply of tools required for the maintenance and operations of the Generator set.8) Supply of maintenance manual books with engine and alternator parts list.9) Supply of installing of exhaust piping of sufficient length with suitable MS pipes extended to outside.10) Erection of acoustic enclosure suitable for 160 KVA Diesel generators, complete with all accessories as above with suitable supports.11) Supply and Filling of Fuel to Run the Genset for Load Testing at Full Load for 8 Hours using Water Rheostat or suitable loading element. After Treatment System: The Entire After Treatment System which includes SCR, DEF Lines, DEF Supply Unit and DEF Tank.

Supply and installation of exhaust piping of sufficient length with suitable MS pipe so as to extend outside the generator with necessary thermal insulation .

Supply of tools such as 1no. 15” cutting pliers, 1no. 6” screw driver, 2nos. 9” screw drives, 1set of 6nos, double ended spanners, 1no. Adjustable spanner, 1no. ½ Ib hammer, 1no. Spanner for removing engine oil plug, 1no. Line tester required for the maintenance and operation of the generator set -1set.

Supply and fixing of AC Chargeable Emergency Lamp 2x11W PL Lamp with all connected accessories

2mx1m Rubber mat suitable for 22 kv installation confirming to IS (5 nos)

Supply and fixing of First Aid Box complete with all First Aid Medicines

Supply and fixing of Shock Treatment Chart fixed in glass frame

Supply and fixing of 4 Nos. Fire Buckets made out of 40x40x6mm MS Angle

Supply and demonstration of Hand Gloves 11KV Grade

Supply and fixing of Danger Board as required by the Electrical Authorities

Supply and fixing of Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Supply and demonstration of Earth Discharge Rod

Preparation of site plan, physical layout, electrical line schematic diagram in 5 sets for HT point and 3 sets for Genset Arrangements, getting drawing approval from CEIG, preparation of completion report, rectification report and arranging CEIG inspection and obtaining safety certificate. Preparation of 1 set of approved drawing and a copy of safety certificate in a neat frame work to be fixed in electrical room and payment of CEIG inspection fees.

Supply and Erection of 300mm Hot Dip/ Powder Coated GI Cable Tray to be fixed with the existing wall, Structure or in Trench in suitable angle iron support.

Supply, erection, testing and commissioning of 250 KVA Servo Voltage Stabilizer for performing 340V-470V Three Phase Input with 415V±1% Output with Line Frequency of 47-53Hz Sipply. Copper wound, indoor type, Oil Cooled transformer mounted on base channel bolted to a suitable RCC plinth capable of bearing 2 ton weight and connected works fitted with the following:1)Cable End box suitable for connection of 2 x 185 sq.mm LT Cable end box 2) Control: Digital 3) LCD Display: Date & Time, Input Voltage, Output Voltage & Current 4) Log book Memory (Non-volatile):- a) No. of Hrs. of operation on mains b) Peak Current demand c) Nos. of Abnormal High Voltage cut-off events. d) Nos. of Abnormal Low Voltage cut-off events. E) No. of Hrs. of operation. 5) Programmable Features: a) HV cut-off set. b) LV cut-off set. c) O/L trip set. d) Time delay set e) Operating mode (auto/manual) 6) Efficiency: >97% 7) Cooling Type: ONAN 8) Protection: a) Automatic Switch-Off against:· Under / Over-Voltage. Over-Load & Short – Circuit & Single Phasing. b) Class C Type Secondary surge Protection.

Design, supply, erection of 200KVAR, 8 stage switching, sequence automatic power factor correction wall mounting stand vermin proof cubical panel board made of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting capacitor chamber relay with metering chamber and compartmentalised out going feeders with suitable capacity MCCB with panel board with provision for louvers and cooling fan for proper ventilation to manage heat load incoming - DPX 400A FP MCCB with rotary handle. Outgoing : 8 stage capacitor bank Contactors : Bharatia Cuttler Hammer/L&T Heavy Duty contactors. Relays : World class solid state relays with TM2 technology as an option. Capacitor MPP capacitor 8 stage from 1 KVAR to 200 KVAR 1. stage -1 KVAR 2. stage -1 KVAR 3. stage -3 KVAR 4. stage -5 KVAR 5. stage -15 KVAR 6. stage -25 KVAR 7. stage -25x2 KVAR 8. stage -50X2 KVAR Bus bar: 2 run of 25mm x 3mm tinned copper Metering : 1-250A Ammeter with CT coil 2) 0-500V voltmeter 3) Advance micro controller based intelegent power factor controller with self dianostic sensing and digital net work analayset with software for mentiory and saving para meter of a suitable multi function meter. Indication: R,Y,B The panel should be coated with Epoxy based painting and the whole assembly fixed in suitable cubical panel grouted in floor with connection complete

Supply and clamping of 8mm dia Aluminium alloy Solid Round Conductor of material AlMgSi used as down conductor system with necessary Conductor Holder,glue, connectors, joints and expansion piece etc as per IEC 62561-2 recommendation and site condition

Supply and installation of air termination rod of 2mtr length of material AlMgSi of diametre ø 16/10 mm crimped on both the ends (Tappered Type). The rod shall be mounted with stainless steel clamp and fixing accessories. It should satiesfies IEC 62561-1 & 2 and it should Withstand Minimum wind velocity of 150m/s.

Supply and Installation of Battery operated LCD type Lightning counter - LCD screen shows the number of lightning strikes, hour and date of lightning events Buttons enable TIME/DATE setting and log viewing. Replaceable battery, working life minimum five years, Complies with IEC/EN 62561-6.

Supply and run of Rust resistant non corossive 10 mm dia Copper Bonded Steel round conductor used for Earth termination inside the concrete and soil with necessary masonary and excavation work .

Supply and installation of stainless steel SS 304 Grade conductor Holder for fixing the 8-10 mm dia round conductor on the wall Test Parameter: a. Mechanical Load b. Environmental Test Should be Tested as per IEC 62561-4

Supply of Maintenance Free Copper bonded Earth rod of 3000mm length having the dia of 17.2 mm with copper coating thickness of 254 microns. The rod has been tested for Dimension, Marking, Tensile Strength, Salt mist, coating thickness, Electrical resistivity test before and after corrosion test as per IEC 62561-2.

Supply and insallation Cabinet Type Class 1 and 2 Combined Model SPD in 4P enclosure box to arrest surges and overvoltages in the power linedue to lighning switching action etc. they must be installed in the incoming MCC panel / DB of the respective building in parallel to the power circuit by using 4 of 6 Sqmm Cu (3 phase power network)

ADD GST 18%

MUTHUSWAMY CONSTRUCTION (BID ID -1210384)

SURA BUILDERS (BID ID -1210643)