8570 REPAIR TO PLUMBING SANITARY FITTINGS TILING AND CONNECTED MISC B R AT 15 JAT UNIT VBV DCA MAP PH I UNDER AGE B R I OF GE SOUTH PUNE

Amount

S&F 30 mm thick flush shutters, solid core construction, with particle board core and plywood face panels, one face is to be covered with decorative face veneer with lipping / beading patti around edges etc. complete all as specified and directed

S & F 30 mm thick 2nd class hard wood glazed and skeleton shutters, devided into squares with plain, chamfered or rounded mitered and rebated sash bars any numbers, open rebated prepared to receive gauze, edges of framing plain, chamfered or rounded , fitted with cut and mitered beads for securing glass etc size of members of shutters in SSR Part- I, Section 8, Clause 8.24 (a), complete all as specified and directed

M & L for preparation of new or previously untreated surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer to newly wood surfaces complete all as specified and directed.

S&F factory made precast SFRC cover slab with frame area of each not exc. 0.75 Sqm and thickness not less than 75 mm in concreting including groove and hook arrangement for lifting and placing at site and also side of cover slab shall be covered MS sheet with collars etc complete all as specified and directed.

M & L for rendering 15mm thick in cement mortar 1:6 on brick / concrete surfaces finished even & smooth with a thin layer of sagol finish, including taking down of old unserviceable plaster, racking out joints, etc. complete all as specified and directed

M&L for 10mm thick rendering in cement mortar (1:4) on ceiling surfaces and finished even and smooth with sagol finish, including taking down of old unserviceable cement plaster from ceiling, etc. complete all as specified and directed

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over and including 2 mm thick wall care putty complete all as specified and directed.

M & L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed

S & F in repairs vitreous china squatting Pan " Orissa " pattern of size 580 mm X 440 mm white with integral foot rests ( excluding flushing cistern and flush pipe) including provn of cement concrete bedding complete all as specified and directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed

S & F in repairs wash hand basins, vitreous china of size 550mm X 400mm ( flat back or angle back type) including cutting for and pinning in ends of brackets or erecting stand inclusive of supply and fixing waste pipe etc. complete all as specified and directed.

S&F 32 mm bore CP waste coupling suitable for kitchen sink with necessary washer and gratings, etc. complete all as specified and directed.

S & F in repairs 15 mm bore pillar taps, fancy type cast copper alloy with capstan heads, chromium plated , screwed down high pressure with or without lattered " HOT" or " COLD" with long screwed shanks and fly nuts, complete all as specified and directed.

S & F in repairs 15 mm bore bib taps, fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 32 mm bore waste fittings brass chromium plated with long screwed shanks and fly nuts,screwed for iron pipe suitable for WHB complete all as specified and directed.

S & F in repairs 15 mm bore, 600 mm long PVC connections with PTMT nuts complete fixed to iron pipe at both ends complete all as specified and directed.

S & F in repairs 15 mm stop valves, fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down and screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repairs 15 mm stop valves, concealed, fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down and screwed both ends for iron pipe or for union complete all as specified and directed.

M&L for mild steel structural steel work, framed as in trusses, purlins, rafter etc. conforming to grade E-250 (Fe-410W, quality A) including shaped washers including necessary cutting required length, notching drilling, riveting and or welding or connecting with nut bolts with angle cleats, fish plat, gusset plate and also erecting in true position including dismantling of old unserviceable truss complete all as specified and directed

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surface of any description exc. 10 cm width or girth, including preparation of new steel surfaces, complete all as specified and directed.

S & F roof sheeting pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws including taking down of old unserviceable AC sheet complete all as specified and directed.

Supplying, fixing, jointing and testing galvanised iron tubing medium grade including with all fitting & fixtures such as bends, elbow, socket, reducer etc and fixed to wall, ceiling or laid in floor including taking up or down of old unserviceable GI water tubing complete all as specified and as directed for the following sizes:- (a). 15mm bore.

(b). 20mm dia bore.

Excavation in any type of soil for post holes (or similar holes) each n.exc. 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth arround, in layers n. exc. 25 cm, watering, and removing surplus soil to a distance n. exc. 50m and making good disturbed surfaces, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation filling / mass concrete / base of fencing posts, complete all as specified and directed.

Taking down angle iron chowkhat or frames exc. 1.5 sqm but n. exc. 4 sqm each with shutter without taking off shutter from the frame complete all as specified and directed.

M&L for 18/19mm thick pre-laminated particle board both side decorative face, including providing second class hard wood 6mm thick beading for edges of board alround including dismantling of unserviceable boards complete all as specified and directed

S&F catch spring or fanlight pivot with plate size 20 mmx50 mm and suitable for shutter of 25 mm thickness, fixed with screws, etc. complete all as specified and directed

S&F 30 mm flap width continuous piano hinges, mild steel, bright finish or electro galvanised, etc. complete all as specified and directed

S&F 125 mm size, extruded brass handles, fabricated type, and polished, etc. complete all as specified and directed

S&F brass Locks, cupboard, grade I, size 65 mm (2 lever) with two keys complete all as specified and directed

M&L for 75mm thick PCC 1:4:8 type D-2 (Using 40mm graded stone aggregate) as in sub base of floor, finished the surfaces fair & even to receive floor finishes, including demolition of old existing unserviceable cement concrete floor / pavings and remove debries outside the defence land complete all as specified and directed

M&L for coloured precast cement concrete interlocking tiles 60mm thick, M-35 grade of any shape and size, conforming to IS-15658-2006 glossy finish as in floor / pavement laid over and including 40mm thick stone dust cushioning, laid dry to the profile over rammed sub base complete all as specified and directed

Taking down shutters of any description exc. 1 sqm and not exc. 2 sqm each, complete all as specified and directed.

Taking down wooden chowkhat or frames exc. 1.5 sqm but n. exc. 4 sqm each with shutter without taking off shutter from the frame complete all as specified and directed.

Taking down wooden chowkhat or frames n. exc. 1.5 sqm each with shutter without taking off shutter from the frame complete all as specified and directed.

Taking down / cutting steel window shutters by means of gas cutter without disturbing of soffit / jambs / cills etc. of any description n.exc. 1.5 sqm (without taking off guard bars) complete all as specified and as directed

S&F three track sliding window with two or more shutter witth 4 mm thick tinted glass , one shutter of stainless steel wire cloth 0.36 mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing, handle lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to following catalogue of 'JINDAL' or of equivalent make as mentioned in list of makes here-in-after complete all as specified directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & Verrtical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & Bottom 20844 (f) Glazing Clip 19352

S&F ventilators / louvers with partially gauged shutter using 4 mm thick x10 cm width frosted glass strip with following aluminium powder coated sections confirming to JINDAL catalogue or of equivalent makes as mentioned in list of makes here-in-after with and including necessary rubber beading, cleats and locking arrangements, etc. complete all as specified and directed:- (a) SP-20048 (b) glazing clips-19352

S & F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, including flush pipe 32 mm dia, complete all as specified and directed.

S & F gratings 100 mm dia of PTMT (minimum weight 25 gms), complete all as specified and directed.

S & F in repairs 125 mm dia swivel type brass chromium plated shower rose of approved quality, complete all as specified and directed.

S&F in repairs 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe including taking down old unserviceable valve etc. complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 500 Litres capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with and including tank nipple of existing size including dismantling of old unserviceable water tanks and removing to store complete all as specified and directed

S&F PVC black colour water tank cover with fixing brackets suitable for 500/1000 ltrs capacity tanks, etc complete all as specified and directed.

S & F Transparent Glass 7.5 x 7.5 inch as in corner bathroom shelves with bracket (set of 2) (Model- Joyo Cera Gls 132 or equivalent), complete all as specified and directed.

S & F 100 mm long butt hinges medium weight, cold rolled mild steel for door shutters, complete all as specified and directed.

S&F 150 mm aluminium anodized barrel tower bolts of extruded section for door shutters, complete all as specified and directed.

S & F 300 mm long aluminium alloy , anodised sliding door bolt with hasp , staple( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast - aluminium alloy and fixed, complete all as specified and directed.

S & F 150 mm extruded aluminium alloy handles, fabricated type anodised, complete all as specified and directed.

M&I for repairs to stainless steel cupboard and way locking system handle, MS butt hinges, shelves partition, replacement locks with replacement of damaged steel handle with mortise lock of mild steel, vertical type, 65mm size, two lever ISI marked and provide suitable hinges and proper erection of CB shutters with and including 12 mm dia locking rods applying one coat of synthetic enamel paint over a coat of primer etc. complete all as specified and directed by Engr-in-Charge

Hacking out old broken glass (any thickness size, quality or description ) from Aluminium sliding window/ metal frames and M & L for providing sheet glass 4mm thick ordinary quality tinted / plain fixed with rubber beading or glazing clips ,etc, each pane exc. 0.5 Sqm in area, complete all as specified & as directed .

Taking down old fly proof wire mesh from aluminium three track window shutters (any thickness size, quality or description) and M & L for replacement of stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm & fixed with stainless wire staples, bearing, window lock, beadings and including servicing for smooth functioning of sliding of each pane exc. 0.50 Sqm in area, complete all as specified and directed

M&L for hasp & staple 75mm size, aluminium anodised, safety type, aluminium anodised, including bolt to hing plate and fixed with screws, complete all as specified and directed.

S&F in repairs stainless steel plate rack made from 1.00 mm thick sheet grade SS- 304 of standard size 30"x32"x8"/10" and of approved quality of finish complete all as specified and directed.

S&F two legged aluminium floor door stepper with rubber shoe 140mm long complete all as specified and directed.

M&L for complete removal of existing treatment from wall surfaces, applying two coats of oil bound distemper over a coat of primer including preparation of old painted surface, etc. complete all as specified and directed

S&F in repair tubular towel rail brass chromium plated 20mm dia 600mm long fixed with brass screws, complete all as specified and directed.

Taking down shutters of any description n.exc 1.0 sqm each and resecuring or easing & adjusting after repair in door opening and connected carpentry work and refixing at same opening complete all as speicified and directed.

Taking down shutters of any description exc 1.0 sqm but n.exc 2.00 Sqm each and resecuring or easing & adjusting after repair in door opening and connected carpentry work and refixing at same opening complete all as speicified and directed.

Rounding to edges of stone slabs one edge, such as in steps, shelf cooking platform, and other similar situations, complete all as specifed and directed.

M&L for machine cut cudappah stone slab, 20mm to 25 thick, laid over and including cement screed base of 15 mm thick in CM 1:6 laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing including dismantling of old unserviceable stone slab and removal of debries outside MD land etc. complete all as specified and directed

M&L for Non skid ceramic colored tiles 300x300x7to8mm thick, (square/ rectangular) as in floor etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer in CM 1:6, including demolition of old unserviceable tiles and removing of debries outside MD land,etc. complete all as specified and directed.

M&L for coloured glazed ceramics tiles 450x300x7to8mm thick in vertical surfaces such as skirting dado set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick rendering in cement mortar 1:4 on stone / brick/ concrete masonry surfaces of walls with and including triangular filletting in CM 1:4 on top edges including demolition of old unserviceable tiles of any description or thickness laid bedded and pointed in any mortar etc and removing of debries outside MD land complete all as specified and as directed.

M&L for (light shade) vitrified ceramic tiles of size 600x600x10 mm thick (square/ rectangular) polished as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, including demolition of old unserviceable tiles and removing of debries outside MD land, etc. complete all as specified and directed.

M&L for machine cut kota stone slab 20-25 mm thick as in steps riser and tread, landing and mid landing of staircase, laid over and including 15 mm thick screed bed in cement mortar 1:4 and jointed and pointed in neat cement slurry mixed with pigment to match the shade of kota stone including rubbing and mirror polishing including dismantling of old concrete damaged slab tiles and removal of debries outside MD land etc. complete all as specified and directed

M & L granite ( of any type ) work ( table rubbed and polished ) 18 to 20 mm thick as in steps, jambs, pillars, window cill, cooking platform and flooring in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite with and including screed bed or bedding layer of 15 mm thick in CM 1:6 on masonry surfaces, including dismantling of old unserviceable stone slab and removal of debries outside MD land etc. complete all as specified and directed

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to steel or wooden windows / door / shutters / frames etc. complete all as specified and as directed.

S&F in repairs, Harrison rail, mild steel, chromium plated as in curtain rod, 25mm bore (Medium weight) with fixing brackets, stops, rollers etc. complete all as specified and directed.

S & F mild steel, chomium plated brackets suitable for 25mm bore curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc and match as required, complete all as specified and directed.

S&F 32 mm bore PVC waste pipe of 90 cm long suitable for kitchen sink / WHB waste water, etc.complete all as specified and directed.

S&F 40 mm bore PVC waste pipe including fitting elbow, tee, socket, etc., fixed to wall / in floor for WHB, etc. complete all as specified and directed.

S&F door closer hydraulicaly regulated, designation No.3 universal type, suitable for door shutters of 851 mm to 1000 mm width and weight between 61 to 80 kg,etc.complete all as specified and directed.

S&F double action floor spring spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main boady with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specified and directed.

Cutting chases, pinning in, concrete block walling & making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc. and cutting chases for concealed water tubing and making good, cutting n. exc. 10 cm girth, complete all as specified and directed.

M&Lfor fly ash bricks, straight or curved on plain exc. 6m mean radius, built in cement morter 1:4, as in half brick thick walling including demolition of half brick wall and removal of debries to out side MD land etc. complete all as specified and directed.

M&L soap dish chromium plated brass fixed width brass screws as in repair complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with M.S square tube, supplying & fixing in opening as per specifications, drawings complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting, of frame made out of M.S tubes for top & bottom rails M.S frame shall be covered with heat molded plain co lour PVC ‘C’ channel having a PVC sheet strip of 20mm width struck inside with solvent cement for steel & plain co lour PVC sheets for top rail, lock rail& bottom rail on either side & or gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile & rails with suitable PVC sheet banding, and joints to gather with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F for 110 mm dia PVC SWR pipes single socketed in any length with rubber ring joints fixed to wall including clamp etc including taking down of old unserviceable pipes, complete all as specified and directed.

S&F for 75 mm dia PVC SWR pipes single socketed in any length with rubber ring joints fixed to wall including clamp etc including taking down of old unserviceable pipes, complete all as specified and directed.

S&F pressed steel frames of size 125mm X 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strikes plate, including providing PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) to fill up the hollow portion of the frame complete all as specified and directed.

S&F pressed steel frames of size 105mm X 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strikes plate, including providing PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) to fill up the hollow portion of the frame complete all as specified and directed.

M&L for providing cement concrete type C- 1, 1: 3:6 (using 20mm graded stone aggregate) 75 mm thick as in plinth protection finishing even and fair on top using extra cement with 6mm wide joints throughout the thickness of plinth protection including demolition of existing unserviceable plinth of any type and remove debries complete all as specified and directed.

S&F PVC (SWR) bends of 110 mm bore, complete all as specified and directed.

S&F PVC (SWR) bends with oval access door of 110 mm bore, complete all as specified and directed.

S&F PVC(SWR) bends of 75mm bore, complete all as specified and directed.

S&F PVC(SWR) bends with oval access door of 75mm bore, complete all as specified and directed.

S&F in repairs PVC SWR Branch piece single (Single Y) equal or unequal 110mm dia with door access, complete all as specified and directed.

S&F in repairs PVC SWR Branch piece single (Single Y) equal or unequal 75 mm dia with door access.

S&F in repairs 75mm dia SWR junction (single 'T') equal or unequal with door access, complete all as specified and directed.

S&F in repairs 110mm dia SWR junction (single 'T') equal or unequal with door access, complete all as specified and directed.

S&F in repairs 110mm dia SWR junction (single 'T') equal or unequal, complete all as specified and directed.

M&L for carrying out non destructive water proofing treatment to sunken slab of toilets consisting of one WC, one nahani trap at bathroom and one nahani trap at Kitchen including cleaning of surface with wire brush to removing loose particles, greasy elements, detecting leakage point, sealing joints of tiles / cracks in floor and wall and injecting injection of CORESEAL 135A/ CORESEAL 135B all as per manufactures insrtuctions complete all as directed by Engr-in-Charge. (Make:- AQYATYTE, CREAT, SEAL, grouting compound of Ashwin Enterprises, GPSS (Ground Penetrating sealing systems) of Saga Polytech or similar brand as approved)

R k construction

REKHA ELECTRICALS

SARATH ENTERPRISES

shiva traders

Gauri Associates

Santosh Pandurang Pise

AJINKYA VIKRAM GAIKWAD