ADDITION/ALTERATION TO BLDG NO P-127 (JCOS MESS) OF HQ AFSOD, PROVN OF TOILET BLOCK AND ALLIED INFRA NEAR BLDG NO. T-05 AT AFSOD AND PROVN OF RCC STAIR CASE 2 NOS (TWO WAYS EACH STAIR) FOR FIRE SAFETY OF KV NO.3 AGRA UNDER GE (W) AGRA

Amount

Dismantling brick tiles on roof top laid bedded & pointed in any mortar and removing from site all as specified and directed.

Dismantling of mud in roofs, any thickness, including plastering and leaping (whether full thickness removed or only a part thereof) all as specified and directed. (Removing of debries shall be measured & paid separately)

Disposal of demolished soil/materials exc 1.50 km but n. exc 5 km and depositing where directed complete all as specified and directed.

Cutting grooves in brick wall 75 to 125mm wide and 65mm deep and shaping horizontal face of groove making good with CM 1:3 or PCC 1:2:4, type B0 (using 12.5 mm graded stone aggregate) complete all as specified and directed.

M&L cement concrete 1:2:4, type B-0 (using 12.5 mm graded aggregate) in benching, coping, padding, roof kerbs or mud stops, rounded or chamfered on edges and similar work including necessary use & waste of form work all as specified and directed.

M & L for water proofing treatment of roof slab all as follows: - (a) M&L for preparation of roof surfaces by brushing, cleaning and Applying a priming coat with bitumen primer @ 0.5 ltr/Sqm (b) Applying a hot blown bitumen grade 85/25 @ 1.2 Kg/sqm (c) Laying APP modified water proofing membrane weighing not less than 3 Kg/Sqm will be laid over applied bitumen. (d) Applying a tack coat of hot bitumen grade 85/25 @ 1.2 Kg/Sqm and sand in confirming to Zone II in dry condition will be dusted over the bitumen @1.00 Kg/Sqm

M&L brick tiles 40 mm thick laid over 15 mm thick screed bed in CM 1:3 and jointed in CM 1:3 mixed with 5% of crude oil by weight of cement complete all as specified and directed.

All as per item No. 7 above but EXCEPT brick tiles. Note : Re-usable brick tiles obtained from item No 1 shall be used after cleaning.

Demolition of wall, ceiling board ( fiber pulp, insulation etc) or insulation board/ slabs/blankets, any thickness, incl cover fillets all as spd and directed

M&L Anodised aluminium snap grid frame work for false ceilingcomplete all as specified and directed

M&L for hangers 6mm dia GI (up to 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed

M&L 6mm Exposed metal frame ceiling with calcium silicate board if siliceous and calcareous material reinforced with cellulose fiber for fixing in 600 x 600mm grid complete all as specified and directed (Frame work for ceiling shall be measured and paid separately)

S&F in repair vitreous china squatting pan Orissa pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including traps complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan pedestal pattern P-Trap white complete with seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

PCC 1:3:6 C-1 (using 20 mm graded crushed stone aggregate) as in cement concrete in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, bed blocks for fixing hold fasts, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed all as specified.

M&L Machine cut kota stone 20-25 mm thick as in floor, stair case, landing etc. laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and mirror polishing over 20mm thick screed bed in CM ( 1:6) as in floor complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed

M&L for coloured glazed ceramic tiles (Digital & designer Pattern) in vertical surface 350 x 250 x 7 mm / 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including taking down cement plaster and 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed .

M&L ceramic joint free coloured tiles (1st quality/premium quality) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11Sqm but not exc. 0.18 Sqm as in floors, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.38 sqm, in floors, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM ( 1:6) complete all as specified and as directed.

Taking down cement or cement lime plaster of any description on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately)

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

M&L for 15mm thick rendering in CM 1:6 on any faces of brick or concrete surfaces of walls & finishing the surface complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on brick or concrete surface with water proofing compound @ manufacturers instructions finished fair complete all as specified and directed. Note : Water proofing compound will be measured and paid separately under respective item of Sch ‘A’.

M & L for rendering 10mm thick in CM 1:3 on ceiling surface finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

M&L for applying three coats of white wash on wall including preparation of new plastered surfaces of walls, complete all as specified and directed.

M&L for preparation of old decorated plastered or un-plastered surface of wall and applying one coat of white wash complete all as specified and as directed

M&L for applying three coats of white wash on ceiling including preparation of new plastered surfaces, complete all as specified and directed.

M&L for preparation of old decorated plastered or un-plastered surface of ceiling and applying one coat of white wash complete all as specified and as directed

M&L for applying two coats of external weather proof paint over a coat of alkali resistance priming paint on wall including preparation of new plastered surfaces, complete all as specified and directed.

M&L for applying two coats of external weather proof paint over a coat of alkali resistance priming paint on wall including complete removal of old treatment ,complete all as specified and directed.

M&L for two coats of oil bound distemper over a coat of average 1mm thick putty on new plastered surfaces complete all as specified and directed.

M&L complete removal of existing treatment and applying two coats of oil bound distemper over a coat of average 1mm thick putty on new plastered surfaces complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying one coat of weather proof in different tint as in band/strips and similar works complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

S&F mild steel joist channel, angle, I sections or tee sections fixed independently with out connecting plates as in water tank platform, supports for staircase, chajjas etcof grade fe-410-0 & fe 310-0 complete all as specified and directed..

S&F 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs, platforms etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection complete all as specified and directed.

S&F 15mm bore steel water tubing, medium grade, galvanized including fittings and fixed to walls, ceilings, floors or laid in floors complete all as specified and directed.

S&F 20mm bore steel water tubing medium grade galvanized including fittings and fixed to walls, ceilings, floors or laid in floors complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth etc. brick walls complete all as specified and directed.

S&F in repairs CP Bib taps fancy type long body 15 mm cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and directed.

S&F in repairs 10 ltrs capacity PVC flushing cistern low level (white) with inlet ball valve and handle including brackets, rubber bush, washers etc complete all as specified and directed.

S&F in repair 15 mm bore CP Angle/Stop valves, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

S & F in repair CP health faucet with 1.5 mtr PVC connection pipe complete all as spd and directed

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified & directed.

S&F CP brass urinal spreader for fixing with 15mm dia pipe complete all as specified & directed.

S & F in repairs CP Swivel shower fixing to 15mm pipe including fixing to steel pipe or union complete all as specified and directed

S&F in repairs CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed

S&F in repairs Vitreous china wash basin white flat back size 550 x 400mm incl waste pipe chain plug brackets complete all as specified and directed. .

S&F in repairs Vitreous china wash basin pedestal type white flat back size 550 x 400mm incl waste pipe chain plug brackets complete all as specified and directed.

S&F 15mm bore, brass chromium plated pillar cock swan neck (foam flow) screwed down for pipe and fixed complete all as specified and directed.

S&F CP waste coupling of PTMT (half or full threaded) of 32mm bore suitable for wash hand basin/ kitchen sink/urine pot complete all as specified and directed.

S&F 32 mm dia PVC waste pipe for urine pots/wash basin /sinks 800mm long complete all as specified and directed. Make Prayag Cat No 327 or equivalent

S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

S&F in repair 500 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F in repair 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter sunk wash basins and like in cement mortar 10mm (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed

Chamfer, splays or arris in face work of granite, marble etc complete all as specified and as directed

S&F in repairs kitchen sink double bowl with single drain board made of stainless steel 1mm thick with plugs, washers and wasts pipe including bedding in cement mortar on to dwarf wall or including supply & fix cast iron cantilever brackets and connecting union to pipe, overall size 1730x510mm bowl size 510x405x250 mm complete all as specified and directed.

S&F in repair plate rack of 1mm thick stainless steel of size 36" x 48" 10" (inches) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel windows with side hung shutters including projecting type hinge with steel handle and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and directed.

S & F steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, guard bars etc, with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe 290 Gde E-165 complete all as specified & directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10 cm width or girth, not otherwise described complete all as specified and directed.

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F 3 mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

M&L Rolled sections as in framing for cladding, door chowkats, cooler stands, glazing and the like fixed with angle cleats and connecting plates, etc (Fe-290 gde E-165). complete all as specified and directed.

S&F 12mm toughened frosted glass door (made in required design) of size 2.1m x 1.4m including 2 x Fancy handles 300mm x 20mm size, top and bottom locking devices, top and bottom spring mechanism complete all as specified and as directed

S&F solid PVC frame of size 50x47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube supplying & fixing in opening as specified in clause No. 8B.3 at Sl page No. 145 and shown in drawing on sl page No 160 of SSR 2010 respectively and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed

S&F 100 mm long stainless steel hinges type B-12 complete all as specified and directed.

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F powder coated (15 micron) aluminium door/window/ventilator frame and side/top hung or sliding shutter complete and fixed with fittings, one or more rebates including jointing cleat, glazing clips, rubber neoprene packing, aluminium snap beading, screws, anodised aluminium fittings etc. complete all as specified. Note: (i) Sheet glass and particle board, hinges, lock, handle, floor spring, hydraulic door closer will be measured and paid separately (ii) Aluminium door frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed. (iii) The gap shall be sealed externally with Polysulphide sealant and finished flush with the surface

S&F aluminium grills of standard section, type A diagonal, with U rail, necessary jointing cleats, screws fixed with frame etc complete all as specified and as directed.

S&F 10 mm toughened glass frosted in approved design fixed to aluminium frame complete all as specified and as directed

S&F 5.5mm Sheet glass, ordinary quality fixed to aluminium frame complete all as specified and as directed

S&F 35 mm thick 2nd class hard wood (Hollock/Sal/Bijasal), locally fabricated glazed skeleton door shutters open rebated and prepare to receive glass, gauge (without sash bars) edges of framing plain chamfered or rounded, fitted with cut including mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I section 8, clause No 8.24 (a) complete all as specified and directed.

S&F 35 mm thick 2nd class plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer including preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth complete all as specified and directed.

M & L for applying one coat of synthetic enamel paint including preparation of old wooden surface of any description not otherwise described over 10 cm width or girth, complete all as specified and directed.

S&F 100 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified and directed.

M&L 300mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F in repair 18 mm thick Rajshree Celuka ply of grade 1 quality of one side pre-laminated and other side plain white colour to make kitchen cabinet/drawer shutters including necessary frame work in desired pattern complete as per specification and as directed by Engineer-in-Charge.

S&F magnetic catcher as in cup boards and drawers complete all as specified and as directed

S&F 50mm dia, polished, hard wood knobs fixed with screws complete all as specified and as directed

S & F Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed

S&F in repairs 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F repairs150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs stainless steel curtain rods rods, 25mm diameter including two decoratine type brackets in each curtain rod incl stainless steel fixing arrangement with drilling holes in walls, brackets etc complete all as specified and directed.

S&F in repairs 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed

S&F in repairs PVC (SWR) Gully traps/nahani traps 125/110mm setting and jointing with solvent cement complete all as specified and as directed

Excavation in trenches in soft/ loose soil not exceeding 1.5 m wide n.exc 1.5m depth for fdn etc for shaft, wells, cesspits, man holes, pier holes etc. n.exc 10sqm on plan and n.exc 1.5m depth and getting out in soft loose soil complete all as specified and as directed

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/ loose soil complete all as specified and as directed

Demolition and breaking up drain pipe (SGSW, AC, RCC or PVC) of 100mm bore incl demolition of PCC as in benching and hauching etc complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in bed of drain pipe incl packing under and haunching against the sides of pipe after they are laid and tested for 150mm dia of pipe complete all as specified and directed.

M&L for Surface excavation n.exc. 30 cm deep and averaging 9cm deep and getting out in loose/soft soil

Removing Excavated soils to a distance exc 1.5 KM but not exc 5.0 KM and depositing where directed at a level not exc1.5 M above the starting point complete all as specified and directed.

M&L 100mm thick PCC 1:4:8 type D-2 (Using 40 mm graded aggregate) as in hard standing, pavement complete all as specified.

M&L 40mm thick PCC 1:2:4 type B-1 (Using 20 mm graded aggregate) as in sub bases, sub floors, floors and pavings finished even and smooth without using extra cement complete all as specified.

M&L for chequered cement concrete tiles 300mm x 300mm x 25 mm thick , with grey cement and pigments, set & jointed in neat cement slurry and pointed with grey cement & pigment in floors laid over and including 20 mm thick screed bed or bedding layer in cm 1:4 complete all as specified and directed.

Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etcof grade fe-410-0 & fe 310-0 complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in Soft/ Loose soil complete all as specified and directed.

M&L for PCC type D2 (1:4:8) as in foundation, filling and mass concrete complete all as specified and directed.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exc 6m mean radius in half brick thick built in cm (1:6) complete all as specified and directed.

Removing excavated material n. exc 50m and depositing where directed at level n. exc 1.50 in soils complete all as specified and directed.

M&L for reinforced cement concrete M25 Design Mix as in footing foundation beam plinth beams bases for columnsetcetc etc complete complete all as specified and directed.

M&L for reinforced cement concrete M25 Design Mix as in columns ,pillars, post And strut etc complete all as specified and directed.

M&L for reinforced cement concrete M25 Design Mix as in beam ,bressummers,lintels over 1.5m span etc complete all as specified and directed.

M&L for reinforced cement concrete M25 Design Mix as in Chajjas etc complete all as specified and directed.

M&L for reinforced cement concrete M25 Design Mix as in Slab supported on walls ,beams and columns in floors, roofs, landings, balconies and in shelves and the like complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:4 with water proofing compound over RCC slab , RCC chajja when it is green etc complete ( Note WPC will be measured & paid separately) complete all as specified and directed.

M&L for form work to soffits of suspended slab/chajja etc not exc 200mm thick rough finished surface of concrete etc complete all as specified and directed.

M&L for form work to sides of concrete foundations , footings, bases of columns ,raft beams ,sides and sofit ( if any) of foundation and plinth beams and similar work or to better rough finished surface of concrete etc complete all as specified and directed.

M&L for form work to sides and soffits of floor or roof beams ,beam haunchings etc also splays between floors and beams etc complete all as specified and directed.

M&L for form work to sides of pillars,posts,strut,piers,columns and stanchions finished surface of concrete etc complete

S&F mild steel TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns hooking ends and binding with mild steel wire anealed not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 6 to 8 mm dia and over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns hooking ends and binding with mild steel wire anealed not less than 0.9mm dia or securing with clips complete all as specified and directed.

.-ditto- 5mm dia and over upto and including 10mm dia in stirrups etc complete all as specified and directed.

M&L for 15 mm thick plastering on other than fair faces in CM 1:4 incl water proofing compound complete all as specified and directed.

M&L for sand filling in floors or pavings laid in layers n. exc 15cm thick spread, levelled and rammed including watering etc complete all as specified and directed.

M&L hard core with broken stone or boulder n. exc 63mm deposited spread and levelled in layers n. exc 15cm thick complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 ( 20mm graded stone agg) 50 mm thick as in floor etc complete all as specified and directed.

M&L coloured non skid ceramic tiles 7mm to 8mm thick ( square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20mm thick screed but n. cm 1:6 complete all as specified and directed.

M&L coloured tile glazed ceramic in vertical surfaces 300x200x7mm set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick backing coat in CM 1:4 complete all as specified and directed.

Mild steel farmed work as in doors (as in ckowkats) or gates of angle or other section with guest plates rail, brasses rail etc exclusive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Gde Fe-290 including shop coat of red oxide including preparation of surface before fixing complete all as specified and directed.

S&F 200mm long mild steel barrel tower bolts, stove enamelled black with bright bolt etc complete all as specified and directed.

M&L for preparation of new surfaces of wall and applying two coats of cement base paint paint over a coat of alkali resistance primer complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 ( 40mm graded stone agg) 75mm thick as in plinth protection laid in alternate by etc complete all as specified and directed.

S&F 1000 ltrs capacity rotational moulded polythene water storage tank ( cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F 15mm dia bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.

S&F 15mm dia stop valve PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.

S&F 15mm dia angle /stop cock PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.

S&F 15mm dia pillar tap PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.

S&F grating round 140mm size of PTMT etc complete all as specified and directed.

S&F towel rail 600mm long of PTMT fixed with R incl chromium plated brass crew with wooden plastic cleats complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mmcomplete all as specified and directed.

S&F 110mm dia PVC(SWR) pipes single sockets in any length with rubber ring joints laid to walls etc complete all as specified and directed.

S&F 110mm dia PVC single T with acceridoor equal of unequal angle etc complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solucent cement of 75mm dia complete all as specified and directed.

S&F PVC (SWR) gully trap, plain with grating including jointing with solucent cement of 125/110 mm dia complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in only length 75mm dia with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F vitreous china squatting pan " ORISSA" pattern, size 580x440mm white with integral foot rest excluding flushing pipe etc complete all as specified and directed.

S&F 10 ltr capacity PVC valueles, symphonic action type, flushing cistern top level, white with inlet, ball valve, float and handle incl bracket 32mm dia flush pipe etc complete all as specified and directed.

S&F vitreous china wash basin, white, flat back, size 550x400mm excluding teps, waste chain 7 plug and porcelain stopper but including brackets complete all as specified and directed.

S&F vitreous china bowl urinal flat back ,size of 465x355x265 mm white(minimum) white grating and union for discharge pipe (excluding flushing cistern ,flush pipe and waste pipe) complete all as specified and directed.

S&F High Density polythene (HDPE) 32 mm dia pipes of pressure rating 6 kgf/sqcm complete all as specified and directed.

S&F 20mm dia gun metal globe or gate valves with iron wheel head screwed both ends per iron pipe etc complete all as specified and directed.

M&L providing reinforced cement concrete type B-1 ,1:2:4 (20mm graded aggregate) in precast manhole,posts,fencing post etc complete as directed.

S&F SGSW drain pipes150 mm dia, laid in tranches and jointed complete all as specified and directed.

Excavating in over areas n exc 1.5m deep and getting out in soft/loose soil, complete all as specified and directed.

M & L RCC M25 (Nominal mix) for foundations, incl rafts, footings, foundations beams , plinth beams, bases for columns etc complete all as specified and directed.

M & L for RCC M25 (Nominal mix) for Walls, retaining walls, basement walls, ballast walls, Stair rails and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

Use and waste of formwork to faces of walls, retaining walls, abutments ,parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, rough finished complete all as specified and directed.

M & L for machine cut & polished smooth surface of kota stone slab 12-15mm thick as in skirting, including 10 mm thick cement mortar rendering 1:4 fix in position etc complete all as specified and directed

S&F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

M&L 15 mm thick plastering in cement mortar 1:4 on fair faces of concrete, surfaced finished even and fair complete all as specified

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc by cement/ colour /plaster to match with the existing location spot complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC FRLS insulated, unsheathed, single core, multi stranded copper conductor cable 1100 volts grade including 1.5sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as earth continuity conductor drawn in and including rigid PVC conduit of suitable size but not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0 mm thick ISI marked plastic laminated sheet cover for fixing switches/ socket/regulators etc including cutting chases in wall as per standard engineering practice & making good the disturbed surfaces to match with existing for the one light/ fan/street/bell point controlled by 1 one way switch 5/6 Amps complete all as specified & directed.

All as per item No-2 here in before but One socket outlet 5/6 Amps on independent bd controlled by one switch complete all as specified & directed.

All as per item No-2 here in before but One socket outlet 5/6 Amps controlled by one switch on same board with other switches complete all as specified & directed.

All as per item No-2 here in before but one socket out let 3/5 pin, 5/6 Amps controlled by one 1way switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

All as per item No-2 here in before but using 2.5 sqmm PVC FRLS insulated stranded copper cunductor cable and for one socket out let 3/6 pin, 15/16 Amps controlled by one 1 way switch on independent board complete all as specified & directed. NOTE-For item no 2 to 6 -: (i)The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillers etc for concealing the conduits to required depth & making good the disturbed surfaces in cement mortar 1:4 including finishing the surface to match with the existing surface.The portion of point wiring at RCC Coloumns/Beams/Ceilings etc shall be in surface conduit of suitable size fixed on surface with using PVC rawl plug and provision of covering terminal boxes/junction boxes of any shape and size with 3 mm thick bakelight laminated sheet fixed with suitable GI screws and cup washers. (ii) Fittings like switches,sockets,regulators,lamp holders,light foittings shall be measured and paid for separately under appropriate item of schedule A. (iii)The size of conduits shall be determined on permissible no of runs of wires as specified in SSR part-I clause 19.125 (B).However minimum size of conduit shall be 20 mm dia (medium grade)

Supply and fix switch piano, flush type, single pole, 5/6 Amps one way, 230 volts complete all as specified and directed. Make: Anchor Cat No.38058 or equivalent as approved by GE.

Supply and fix switch piano, flush type, single pole, 15/16 Amps one way, 230 volts complete all as specified and directed. Make: Anchor Cat No.39991 or equivalent as approved by GE.

Supply and fix socket outlet, 5/6 Amps, flush type, 5 pin 230 volts complete all as specified and directed. Make: Anchor Cat No.38320 or equivalent as approved by GE.

Supply and fix socket outlet, multi-purpose 3 pin 5/6 Amps and 3 pin 15/16 Amps complete all as specified and directed. Make: Anchor Cat No.39994 or equivalent as approved by GE.

S&F for ceiling rose surface bakelite 62.5 x 25 mm size 3 terminals complete all as specified and directed. Make -Anchor CAT Part No-39072 or equivalent as approved by GE.

S&F switch, bell push button, single pole, 5/6 Amps, one way, 230 Volts complete all as specified and directed. Make -Anchor CAT Part No-38047 or equivalent as approved by GE.

Supply and fix electrical bell model city ding dong (Ding dong type) AC, 230 Volts complete all as specified & directed. Make:- Anchor / Cona / Plaza as approved by GE.

Supply and fix lamp holder insulated body with back plate for batten fitting complete all as specified and directed. Make: Anchor Cat No. 39797/ 39800 or equivalent as approved by GE.

Supply & fix rotory stepped type electronic fan regulator mini flush type 100 watt 230 Volts complete all as specified & directed. Make: Anchor Cat No.38284/38660 or equivalent as approved by GE.

Supply & fix in replacement, single pole and neutral sheet metal enclosure (AC box) with a two pin & earth plug and socket with one no. MCB SP of capacity 20 Amps 240 volts IK-08 As per IEC 61439-3 complete all as specified & directed. Make:- Legrand cat part No- 5078 11 & 4085 93 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply and fixing LED Bulb 15 watt, single phase, 230 Volts AC supply suitable for lamp holder complete all as specified and directed. Make :- Havells cat part No-LHLDDEEEML8R015 or equivalent Model of Philips/Bajaj/CG/ Wipro as approved by GE.

Supply & fix surface/wall mounting LED batten 20 watt luminaire having extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver with mounting accessories complete with lamp holders fixed to wall/ ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No-ENDURALINEARNEOBS20WLED865SPCWH or equivalent Model of Philips/Bajaj/CG as approved by GE.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make:- Havells cat part No- LHECDEFOIH1W028 or equivalent model of make ,Philips/Bajaj/ Crompton Greaves as approved by GE.

Supply & fix, outdoor security light LED 36/40 watt luminaire IP 65/66 protection polyster powder coated with pressure die cast aluminium housing and robust construction with reflector cover pre anodised and flat white high transmission acrylic cover or toughened glass, natural white type with electronic driver, connector block etc with internally prewired fixed to building with and including 1.20M long bracket made out of 40mm dia light grade GI pipe bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/MS clamps & 12mm dia bolts, nuts & washers etc and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- ENDURAPEARLNEOSL40WLED757PASYTOPC,Phillips cat part no BRP052 LED 036 CW HP SLA FG S1 PSU GR or equivalent as approved by GE.

Supply & fix NEW GENERATION POST TOP energy saving envirmental friendly long life 35 watt LED luminaire light fitting, IP 65 protection with reflector cover electronic driver, connector block etc with internally prewired fixed to brcket on gate with fixing accessories and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No-RUBYPT35WLED757PSYMTOPC or equivalent model of make Philips/Bajaj/ Crompton Greaves as approved by GE.

Supply & fix surface mounting type bulkhead 10 watt LED luminaire ENDURA RUGBY NEO IP 65 environmental friendly, altra modern energy saving , decorative oval comprising of high brightness LEDs, connector block etc with internally prewired fixed to wall with fixing accessories and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- Cat part No FT10WLED857SSYMBOPC or equivalent model of make Philips/ Bajaj/ Crompton Greaves as approved by GE.

Taking down care fully sub main wiring / service connections of any size including batten/ conduit, and making good the disturbed surfaces of wall/ floor .

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 6.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 4.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

Taking down distribution boards any size any type including MCB TPN/SPN/SP etc and making good the disturbed surfaces.

Supply and fix MCB DB vertical type 4 way VTPN sheet metal enclosure 415 volts with 100 Amp fully insulated standard copper bus bar for each face & surrounded with neutral bars and two common neutral bar, two earth bar including cable ties for cable manegement suitable for housing MCCB TPN 415 Volts as incommer, IP-43, IK-09 as per IEC 61439-3 with metal doors all enclosed on standard steel sheet flush mouting type double door factory fabricated complete without MCB & MCCB but with enclosue blank plate complete all as specified and directed. Make:- Legrand CAT No.507725 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply and fix MCB DB sheet metal enclosure factory fabricated double door SPN 8 way with 100 amps rated copper bus bar 240 volts IP-43, IK-09 with metal doorscomplete all as specified and directed. Make:- Legrand Cat Part No. 5076 11 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply and fix MCCB 4 pole 100 to 125 Amp Icu 16 Kilo Amp and Ics 100% of Icu with adjustable 70% to 100% and thermal magnetic release suitable for fixing in VTPN DB. Make : Legrand cat part 4200 15 to 4200 16 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply & fix Isolator SPN , 63 Amps, 240 volts, 50Hz, IP-20 as per IEC 60947-3 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4065 02 or equivalent model of make ABB/ L&T/ Schneider as approved by GE.

Supply & fix Isolator SPN , 40 Amps, 240 volts, 50Hz, IP-20 as per IEC 60947-3 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4065 01 or equivalent model of make ABB/ L&T/ Schneider as approved by GE.

Supply & fix MCB SP, 40 to 63 Amps, 'C' Curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4085 96 to 4085 98 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply & fix MCB SP, 6 to 32 Amps, 'C' curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4085 87 to 4085 95 or equivalent model of make Siemens/ Schneider as approved by GE.

M & L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanised steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe upto 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Looose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1 .

M&L for electrically disconnecting and taking down existing ceiling/Exhaust fans from any hight or in any position from existing bldg and keeping in safe custody for reuse at site after necessary repare/ servicing & painting with one coat of synthetic enable paint and writing of MES/identification No. of fans and re hanging/ re-fixing in original position but including replacement of three cor flexible copper conductor cable from ceiling rose to fan connector block of soze 0.75 Sqmm and hanging fan clamps, nuts, bolts and rubber reel bush etc & testing for proper functioning complete all as directed at site by Engr-in- Charge

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver including connecting from ceiling rose to fan connector complete all as specified and directed. Make:- Usha/ Bajaj/ Havells

Supply & fix exhaust fans AC single phase 230/ 240 V of size 450 mm sweep with louver including connecting from ceiling rose to fan connector complete all as specified and directed. Make:- Usha/ Bajaj/ Havells

Supply & fix fans ceiling complete with electronic type regulator and accessories 230 V,1200 mm sweep. BEE 5 star rated, complete all as specified and directed. Make :- Havells, Bajaj, Khetain, Usha

Supply & fix Air Circulator fans 230 volts single phase oscillating 400 mm sweep suitable for wall mounting including connecting from ceiling rose to fan connector complete all as specified and directed. Make:- Usha/ Bajaj/ Havells

Supply & Laying, testing ,cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade, with stranded aluminium conductor of size 50 Sqmm 3½ core compele all as specified and as directed. Make :- Havells, Grandlay, Polycab, Finolex

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr deep in soft/loose/ soil for taking out/laying CI/GI pipe line and getting out soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick layers complete all as specified and as directed by Engineer-in-Charge.

Removal of excavated material n.exc 50 mtr away and depositing where directed at a level n.exc 1.5 mtr above from starting point complete all as specified and as directed by Engineer-in-Charge.

Supplying and laying un-rainforced precast concrete cable cover LV type-I flat size 250 mm x 150 mm x 40 mm in trenches for protection of cable.

M&L for sand cushioning dry fine for cable cushioning below and above the cable complete all as directed at site by Engr- in-Charge.

Supply and fixing GI Pipe 40mm Light grade , for cable protection laid in trench under road or path or fixed on pole or wall with clamps with all fittings complete all as specified and as directed. Make :- TATA, Jindal, Prakash Surya

Supply and fix 'Medium Grade' galvanised iron tubes with all fittings such as tees bends elbow etc laid in trenches of 25 mm bore complete all as specified and as directed

Supply and fix 'Medium Grade' galvanised iron tubes with all fittings such as tees bends elbow etc fixed on walls/ floors of 20 mm bore complete all as specified and as directed

Supply and fix 20mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed

Supply and fix 25mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed

Material and labour for cutting the road for laying of pipe and repair the same with cement concrete work in pavement/hard standing using 400kg of cement per cubic meter complete all as specified and as directed

Supply and fix ball PVC ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule of size 20mm bore complete all as directed

Material and labour for Drilling and tapping cast iron water mains (in position) for branch connections of the internal 20 mm dia complete all as directed.

M&L for Straight plain brass ferrules (or connecting screws) screwed both ends and fixed Bore Diameter of pipe in 20 mm

Supply & Laying, testing ,cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade, with stranded aluminium conductor of size 16 Sqmm 2 core compele all as specified and as directed.

M/s J S & SONS

Om shri sain ram enterprises

R.S BUILDERS

PD GUPTA AND COMPANY