Special repairs to bldg No. 43 and 45 at CME

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceedidng 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in subbase 75mm thick complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

All as per item No. 4 above, but in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement to match complete over and including 10 mm thick cement mortar in CM 1:4 complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof covering complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

S&F mild steel , corrugated (1.25 mm thick), black sheet in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or river sand fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation boards/slabs/blankets) any thickness, including cover fillets complete all as specified and directed.

M & L for Asbestos cement Plain building boards , fixed to timber framework with screws(false ceiling with 6mm thick board) complete all specified and directed by engr-in-Charge.

M & L for plain fillets work (Square, rectangular or triangular in section, clean sawn, secured with nails or brads), exc. 13 & n.exc. 25 Sq cm complete all specified and directed.

M & L for second class hard wood in (wrought timber framed and fixed) in scantlings complete all specified and directed.

Demolition of brickwork or stone/block/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc or pre-cast concrete articles etc all as specified and directed.

M & L for precast plain cement concrete solid block type C-1, 1:3:6 built in CM 1:6 complete as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key, scrubbing down with water all as specified and directed.

M&L rendering 15mm thick on stone/block masonry surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on stone masonry surfaces in CM 1:4 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth with sagol all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of Cement based paint as per manufacturers instruction complete all as specified and directed. Note : The rate quoted by the contractor shall be included for scaffolding to carry out the work for height more than 10.00 mtrs.

M&L for preparing newly plastered surfaces of wall and applying 3mm thick Birla wall care putty and applying two coats of oil bound distemper over one coat primer on walls complete all as specified and directed.

M&L for preparation of newly plastered surfaces ceiling and applying complete ceiling with 3mm POP/Birla putty and making smooth surface and applying three coats of white wash all as specified and directed.

M&L for two coats of synthetic enamel paint on steel and iron surfaces over one coat of red oxide zinc chrome primer of any description over 10 cm in width or girth including preparation of new surfaces complete all as specified and directed

M&L preparing old Steel and Iron Surfaces of any descriptions, over 100mm in width or girth and applying one Coat of Synthetic Enamel Paint, complete all as specified and as directed.

M & L cutting hole in stone walls (exc. 150 sq. cm but n. exc. 400 sq cm) for any purpose and making good dismantled portion in cement mortar 1:3 or cement concret 1:2:4 type B-1 as required complete all as specified and directed.

M & L for PCC Tpye B2 1:2:4 (40 mm graded stone aggregate) in filling and mass concrete complete all as specified and directed.

S&F steel work in tubular trusses including special washer etc., purlins, rafters, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed.

Taking down chowkats or frames, not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames), complete all as specified and as directed.

Taking down chowkats or frames, exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames), complete all as specified and as directed.

S&F 2nd class hard wood plain, solid, straight chowkhats, and frames, wrought, framed rebated on the solid rounded or chamferred, put to gether with glue pinned at joints supplied and fixed complete all as specified and directed.

S& fixed factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edged or panel of 9mm BWP commercial ply over 12mm thick veneered particle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified and directed.

S & F Mild Steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminous paint and sanded, complete all as specified and directed.

M & L for cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed.

S & F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 .

M&L barrel tower bolts stove enamelled black of size 200 mm complete all as specified and directed.

S & F 150mm long Aluminium handles, cast type anodised all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F 300 mm Mild steel sliding door bolts,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 150mm dia double legged door stopper of aluminium alloy with rubber complete all as specified and directed.

M&L for two coats of synthetic enamel paint on wood and wood based surfaces over one coat of pink primer of any description over 10 cm in width or girth including preparation of new surfaces complete all as specified and directed

S & F three track sliding window with two or more shutter with 4 mm thick plain glass or toughened glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make including taking down existing old window with frame of any description complete all as specified and directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & vertical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & bottom 20844

S&F aluminum powder coated fixed partition with frame of size 101.6mmx44.45mmx1.27mm thick and 101.60mmx44.45mmx1.20mm thick with total height (as required at site). The panels shall be made out of 5mm thick plain /tinted (frosted) glass in top & bottm of 12 mm thick both side laminated particle board (i.e 50-50) including door with accessories i.e floorspring, hydraulic door closer, butt hinges, handle, tower bolt, necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screw etc including diamntling , making good to the disturbed portion complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, bell, socket or power) complete including fixture and fittings such as switches, ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. credit for above items should be made as per conditions separately.

M & L for point wiring with FRLSH cable 1.5 Sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 Volt grade in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.50sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface/flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators, etc. complete making good to disturbed surface of wall etc. complete all as specified and directed.

One light point controlled by one switch

One fan/exhaust fan point controlled by one switch and regulator

Scoket outlet, three pin 5 Amps on the same board

Socket outlet, three pin, 5 Amps, independent

All as per item No. 44 above, but with 2.5 Sqmm cable and 2.5 Sqmm for earth continuity for multipin 15 Amps socket outlet flush type on independent board

S & F switch paino, flush type, single pole one way 5 Amps complete all as specified and directed.

S & F switch paino, flush type, single pole one way 15 Amps complete all as specified and directed.

S & F socket outlet 2 in 1, 5 pin, 5 Amps flush type complete all as specified and directed.

S & F socket outlet 5 in 1, 5 pin, 15 Amps flush type complete all as specified and directed.

S & F ceiling rose, PVC/polycarbonate isloted body, surface bakelite 65x50mm. 3 terminal incl PVC square block complete all specified and directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and directed.

S & F surface and wall mounted LED batten (LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 Watt and 02 Nos. PVC square blocks incl taking down old unsv fitting. Make : Havells cat No. LUMILINEBS20WLED830SPCWH or equivalent of Philips/Bajaj/Shakti

S & F LED panel 2 feet x 2 feet size 36 Watt glare free symmetrical including driver and taking down old unsv one complete all as specified and directed. Make: Havells cat No. ENDURASLIMPROPLUS2X2PLR28/36WLED840MOD or equivalent of Philips/Bajaj

M & L for sub main wiring with two run of 4 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 Volt FRLSH cable in and including 1100 Volt electrical grade PVC casing caping of desired colour not less than 1.2mm thick and 25mm wide & 4 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and directed incl taking down old unserviceable one.

All as per item No. 54 above, but size 2.5 sqmm two runs and with one run 2.5 sqmm FRLSH copper wire for earth continuity.

All as per item No. 54 above, but size 1.5 sqmm two runs and with one run 1.5 sqmm FRLSH copper wire for earth continuity.

S & F MCB distribution board double door SPN 240 Volts 12 way with 200 Amps rated bus bar and making good to disturbed surfaces of floors wall etc. including taking down old unserviceable one all as specified and directed.

S & F MCB distribution board double door SPN 240 Volts 8 way with 200 Amps rated bus bar and making good to disturbed surfaces of floors wall etc. including taking down old unserviceable one all as specified and directed.

S & F MCB distribution board double door 240 Volts 4 way with 200 Amps rated bus bar and making good to disturbed surfaces of floors wall etc. including taking down old unserviceable one all as specified and directed.

S & F MCB TPN 63 Amps, 415 Volts, AC incl taking down old unserviceable one complete all as specified and directed.

S & F MCB SP 6 to 32 Amps, 230 Volts, AC incl taking down old unserviceable one complete all as specified and directed.

S & F MCB SPN 40 to 63 Amps, 230 Volts, AC incl taking down old unserviceable one complete all as specified and directed.

Taking down ceiling fan of any size/sweep after disconnecting the wire from existing ceiling rose and refixing the same after cleaning dust, oiling greasing etc. including providing flexible three core from ceiling rose to connector of fan all as specified and directed.

M & L for earthing complete with GI earth plate electrode 60x60cmx6mm thick burried directly in ground in earth pit not less than 2.25 mtr depth below normal ground level with top edge of the plate vertically to depth of not less than 1.5 mtr below ground level connected to & including GI lead 4mm dia as earthing lead connecting to equipment by means of GI bolts & nuts etc with provision of charcoal and salt etc all as per electrical plate No.3 of SSR part-I 2009 including RCC cover and MS angle iron frame, watering with GI pipe 20mm dia (medium grade) & MS funnel, concrete pit including excavation and earthwork in any strata and testing on completion etc. complete all as specified and directed.

GGS Infra

Mukund Engineers and Contractors

BSK Construction

SHINDE DHEERAJKUMAR SIDRAM