REPAIR/MAINT OF LT PANELS, STARTERS, MCCBS JUNCTION BOXES LT DISTRIBUTION NETWORK AND ALLIED ITEMS AT SUNJUWAN MIL STATION

Amount

Taking out of old defective LT panels from site including removing LT cable connection, earthing strips etc including making good the disturb surface complete all as specified and directed by Engineer in-Charge.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board,double door, indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 630 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 400 Amps, 4 pole, DMX SP 2500, 50 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 200 Amps, 4 pole, 36 KA -02 No. (ii) MCCB 125 Amps, 4 pole, 25 KA - 01 No. (iii) Manual Changeover Switch 200A 4 Pole SS Enclosure Extended Handle -02 Nos Foundation- (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on top plateform shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door, indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 630 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 400 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 200 Amps, 4 pole, 36 KA -02 Nos. (ii) MCCB 100 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door, indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 500 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 320 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 250 Amps, 4 pole, 25 KA -01 No. (ii) MCCB 100 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board,double door indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 630 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 400 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 250 Amps, 4 pole, 25 KA -02 No. (ii) MCCB 125 Amps, 4 pole, 25 KA - 01 No. (iii) MCCB 100 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door, indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 630 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 400 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 200 Amps, 4 pole, 36 KA -02 No. (ii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 500 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 320 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 125 Amps, 4 pole, 25 KA -02 No. (ii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 900 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 630 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 320 Amps, 4 pole, 36 KA -01 No. (ii) MCCB 250 Amps, 4 pole, 25 KA - 02 Nos. (iii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubical type, CPRI approved LT panel board, double door indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 900 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 630 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 400 Amps, 4 pole, 36 KA -01 No. (ii) MCCB 200 Amps, 4 pole, 25 KA - 02 Nos. (iii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 500 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 320 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 125 Amps, 4 pole, 36 KA -02 Nos. (ii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door, indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 630 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 400 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 200 Amps, 4 pole, 36 KA -02 Nos. (ii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 500 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 320 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 160 Amps, 4 pole, 25 KA -02 Nos. (ii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. (iii) Manual Changeover Switch 100 Amp, 4 Pole SS Enclosure Extended Handle -01 Nos Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 630 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 400 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 200 Amps, 4 pole, 25 KA -02 Nos. (ii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door, indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 400 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 250 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 100 Amps, 4 pole, 25 KA -02 Nos. (ii) MCCB 63 Amps, 4 pole, 25 KA - 01 No. (iii) Manual Changeover Switch 100 Amp, 4 Pole SS Enclosure Extended Handle -01 Nos Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Supply, installation , Commissiong and Testing cubicle type, CPRI approved LT panel board, double door, indoor type, totally enclosed, dust & vermin proof (protection class IP 65) front opening with self locking arrangment fitted with LT panel made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade internally and externally. The panel shall be suitable for 415 volts, 50 Hz, 3 phase 4 wire system and shall be complete with 630 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables, angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation including earth work and all connected acessories required for functioning of panel board such as thimbles, glands, bolts, nuts, washers etc complete comprising of following-:

INCOMING-: (i) MCCB 400 Amps, 4 pole, 36 KA - 1 No. (ii) Digital type volt meter - 01 set. (iii) Digital type ammeter with suitable rating CTs conforms to relevent IS specification:- 01 set. (iv) LED type indicator lamp set of red , yellow and blue - 01 set. OUT GOING-: (i) MCCB 160 Amps, 4 pole, 25 KA -02 Nos. (ii) MCCB 125 Amps, 4 pole, 25 KA - 02 Nos. (iii) Manual Changeover Switch 100 Amp, 4 Pole SS Enclosure Extended Handle -01 Nos Foundation -: (i) PCC plateform for the panel with PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation, brick work in 1:6 with sub class"B" old size bricks with rendering 15mm in CM 1:6 of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stone aggregate on of top plateform and shall be of a height 45cm above nearest road level.

Earthing complete with GI earth plate electrode 60cmx60cmx6.3mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with top edge of the plate not less than 1.5 meter below normal ground level, connected to and including galvanized iron strip 25x4mm as earth lead by means of GI bolts, nuts, check nuts and washers earth pit surrounded by picked layer of coal dust & salt in equal ratio in all around bottom and top and watering pipe 20mm bore of GI medium grade with funnel all as shown in electrical plate NO 5 of SSR Part I (1991) and connecting to earthing test point, including CI cover, frame and PCC (1:3:6) type C-2 using 20mm graded stone aggregate as in earthing pit with CI cover and framing including necessary earth work etc, complete all as specified. Note :- (i) PCC chamber shall be constructed at least one meter away from building shall be provided in slanting manner. (ii) PCC pit cover shall be precast of RCC 1:2:4 (using 12.5mm crushed stone aggregate.)

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25x4 mm strip galvanised iron or steel complete all as specified.

Earth contuinity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 mm dia galvanized iron or steel wire complete all as specified and directed by Engineer-in-Charge.

GI tubing light grade of size 80 mm dia with all fitting for protecting the cables in tranches,floors,on poles,in walls complete all as specified and as directed.

Cutting of existing road/floor/plinth/drain for taking ot /laying of UG cable throgh GI pipe inclding necessary earth work , excavation and making good to match with existing surface complete all as specified with PCC 1:3:6 type- C1(using 20mm graded crushed stone aggregate ) complete all as specified.

PCC type D-2 ( 1:4:8) using 40mm graded stone aggregates in foundation incl neccessory form work and fair finis to exposed surface without using extra cement etc.complete all as specified.

Aluminium thimble stud type suitable for size of cable 400 sq mm all as specified and directed by Engineer-in-charge.

Aluminium thimble stud type suitable for size of cable 185 sq mm all as specified and directed by Engineer-in-charge.

Aluminium thimble stud type suitable for size of cable 120 sq mm all as specified and directed by Engineer-in-charge.

Aluminium thimble stud type suitable for size of cable 95 sq mm all as specified and directed by Engineer-in-charge.

Aluminium thimble stud type suitable for size of cable 25 sq mm all as specified and directed by Engineer-in-charge.

MCCB TPN 200 Amps , 415 Volts, 25 KA ,4 POLE, Ics=100% Icu , overload adjustable short circuit adjustable type incl complete connection all as per direction of Engr-in-Charge.

MCCB TPN 160 Amps , 415 Volts, 25 KA ,4 POLE, Ics=100% Icu , overload adjustable short circuit adjustable type incl complete connection all as per direction of Engr-in-Charge.

MCCB TPN 125 Amps , 415 Volts, 25 KA ,4 POLE, Ics=100% Icu , overload adjustable short circuit adjustable type incl complete connection all as per direction of Engr-in-Charge.

MCCB TPN 100 Amps , 415 Volts, 25 KA ,4 POLE, Ics=100% Icu , overload adjustable short circuit adjustable type incl complete connection all as per direction of Engr-in-Charge.

MCCB TPN 63 Amps , 415 Volts, 25 KA ,4 POLE, Ics=100% Icu , overload adjustable short circuit adjustable type incl complete connection all as per direction of Engr-in-Charge.

Dismantling old broken plateform and keep in material away from the site and M&L for Construction of platform of size 2.0 mx 2.0m x1.5m of brick work in 1:6 incl excavation 150mm thick PCC 1:4:8 type D-2 in fdn, RFR, filling under floor duly spreading, leveling, ramming, 100mm thick PCC 1:3:6 over 150mm hardcore, finished the top surface with 75mm thick PCC 1:2:4 type B-2 finished even and smooth with using extra cement, Wall finished with 15mm thick plastering in CM 1:4 with WPC, finished the surface even and smooth and apply two coats of cement base paint over a coat of alkali resistance primer, a 750mm wide plinth protection 75mm thick in PCC 1:3:6 type C-1 shall be provided complete all as per specified and directed by Engineer-in-Charge.

Supply/fabricating and fixing of new Chain Link Fencing 50x50mm mesh size for covered the 11 KV substation of 10 to 14mtr length as per site requirement with 2.5m high Chain link fencing, 50x50mm of mesh size made with 4mm GI wire incl 04 Nos of 10mm dia tie round bars, securing with 12mm dia 100mm long botls @ 04 Nos at each post alongwitg 50x6mm FI with 8 Nos of 65x65x6mm angle iron post embedded in PCC 1:3:6 of foundation size of 1.2x 0.50 x0.60 mtr including excavation in post holes and removal of surplus soil to a distance 50m away from the site and provision of MS steel gate of size 2.0 x 2.0m, bottom portion covered with 1.60mm thick MS black sheet and painting work for fencing and gate with two coats of synthetic enamel paint over a coat of red oxide primer colour complete all as specified and as directed by Engr-in-Charge.

Green shade multiporpose HDPE Net 90% superior quality to cover the chain link fencing srounding by tightining by high quality PVC tegs with the iron angle and MS pipe at a suitable distance on plateform of the transformer to avoid approches of animals/children and unwanted persons for safety measures all as specified and directed by Engr-in charge .

Vertical Distribution Board (TP&N) 4 way double door suitable for and including MCCB 125 Amp 16 KA four pole as incomer and out going MCBs and should be IP 43 protected with Copper BusBars, Neutral Links, Earthing bar all as specified and directed. including taking down old UNSV DB/MCB any type. Note:- (i) Rate includes MCCB four pole 125 Amp, 16 KA, 415 volts with adjustable thermal settings. (ii) MCBs shall be measured and paid separately. (iii) TPN DB and MCCB should be of same make.

Distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud TPN 4 way 415 volts double door complete all as directed by Engr-in-Charge. Note:- Distribution board and MCBs should be same make.

Distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as directed by Engr-in-Charge. Note:- Distribution board and MCBs should be same make.

MCB TPN four pole 63-100 Amp 415V 10KA 'B' curve in the DB complete with connection testing and commissioning complete all as directed by Engr-in-Charge.

MCB single poles and current carrying capacity 6 to 32 AMP, 10 KA, B' curve, 240 volt in the MCB DB Complete with connection testing and commissioning complete all as directed by Engr-in-Charge.

MCB SPN and current carrying capacity 32 AMP, 10 KA, B' curve, 240 volt in the MCB DB Complete with connection testing and commissioning complete all as directed by Engr-in-Charge.

Preparation of rusted or previous untreated surface of old painted surfaces of LT panels , cutting/welding of old broken hinges of LT panels the hinges including fixed new CRCA sheet of 3.15 mm thick as per IS 5039 where reqired, cleaning/rubbing and removing the rust from the panel applying two coat of red oxide and two coat of synthetic enamelled paint colour as per existing or as directed by enr-in-charge complete all as specified and as directed.

Fully automatic star delta motor starter in sheet steel enclosure type MN 32 FASD with single phase protection feature and motor rating AC-3 duty, 415 volt, 50 Hz, 3 phase suitable for up to 35 HP motor pump set complete all as specified and as directed.

Fully automatic star delta motor starter in sheet steel enclosure type MN 32 FASD with single phase protection feature and motor rating AC-3 duty, 415 volt, 50 Hz, 3 phase for 20 to 30 HP motor pump set complete all as specified and as directed.

Fully automatic star delta motor starter in sheet steel enclosure type MN 32 FASD with single phase protection feature and motor rating AC-3 duty, 415 volt, 50 Hz, 3 phase suitable for 60 to 100 HP motor pump set complete all as specified and as directed.

M/s Sahib Construction and engineers (BID ID -3489605)

M/S DC CONSTRUCTIONS (BID ID -3489759)

M/S S K Electricals Regd (BID ID -3483977)

M/S AKHILESHWAR ASSOCIATES (BID ID -3487077)

kailu construction co (BID ID -3489676)

VEE ESS ENGINEERS (BID ID -3483948)

M/S JIWAN SINGH (BID ID -3487660)